Dynamics of fibronectin adsorption on TiO2 surfaces

In the present work we analyze the dynamics of fibronectin (FN) adsorption on two different stable titanium oxides, with varied surface roughness, and chemically similar to those used in clinical practice. The two types of titanium oxide surfaces used were TiO2 sputtered on Si (TiO2 sp) and TiO2 formed on commercially pure titanium after immersion in H2O2 (TiO2 cp). Surface characterization was previously carried out using different techniques (Sousa, S. R.; Moradas-Ferreira, P.; Melo, L. V.; Saramago, B.; Barbosa, M. A. Langmuir 2004, 20 (22), 9745-9754). Imaging and roughness analysis before and after FN adsorption used atomic force microscopy (AFM) in tapping mode, in air, and in magnetic alternating current mode, in liquid (water). FN adsorption as a function of time was followed by X-ray photoelectron spectroscopy (XPS), by radiolabeling of FN with 125I (125I-FN), and by ellipsometry. Exchangeability studies were performed using FN and HSA. AFM roughness analysis revealed that, before FN adsorption, both TiO2 surfaces exhibited a lower root-mean-square (Rq) and maximum peak with the depth of the maximum valley (Rmax) roughness in air than in water, due to TiO2 hydration. After protein adsorption, the same behavior was observed for the TiO2 sp substrate, while Rq and Rmax roughness values in air and in water were similar in the case of the TiO2 cp substrate, for the higher FN concentration used. Surface roughness was always significantly higher on the TiO2 cp surfaces. AFM led to direct visualization of adsorbed FN on both surfaces tested, indicating that after 10 min of FN incubation the TiO2 sp surface was partially covered by FN. The adsorbed protein seems to form globular aggregates or ellipsoids, and FN aggregates coalesce, forming clusters as the time of adsorption and the concentration increase. Radiolabeling of FN revealed that a rapid adsorption occurs on both surfaces and the amount adsorbed increased with time, reaching a maximum after 60 min of incubation. Time dependence is also observed for the evolution of the atomic (%) of N determined by XPS and by the increase of the thickness by ellipsometry. TiO2 cp adsorbs more FN than the TiO2 sp surfaces, after 60 min of adsorption, as shown by the radiolabeling data. FN molecules are also more strongly attached to the former surface as indicated by the exchangeability studies. The overall results provide novel evidence that FN spontaneously adsorbs as a self-assembly at TiO2 surfaces as a function of time. The aggregate structure is an intermediate feature shared by some protein fibrillar assemblies at interfaces, which is believed to promote cell adhesion and cytoskeleton organization (Pellenc, D.; Berry, H.; Gallet, O. J. Colloid Interface Sci. 2006, 298 (1), 132-144. Maheshwari, G.; Brown, G.; Lauffenburger, D. A.; Wells, A.; Griffith, L. G. J. Cell Sci. 2000, 113 (10), 1677-1686).     

Arrays of lipid bilayers and liposomes on patterned polyelectrolyte templates

This paper presents novel methods to produce arrays of lipid bilayers and liposomes on patterned polyelectrolyte multilayers. We created the arrays by exposing patterns of poly(dimethyldiallylammonium chloride) (PDAC), polyethylene glycol (m-dPEG) acid, and poly(allylamine hydrochloride) (PAH) on polyelectrolyte multilayers (PEMs) to liposomes of various compositions. The resulting interfaces were characterized by total internal reflection fluorescence microscopy (TIRFM), fluorescence recovery after pattern photobleaching (FRAPP), quartz crystal microbalance (QCM), and fluorescence microscopy. Liposomes composed of 1,2-dioleoyl-sn-glycero-3-phosphocholine (DOPC) and 1,2-dioleoyl-sn-glycero-3-phosphate (monosodium salt) (DOPA) were found to preferentially adsorb on PDAC and PAH surfaces. On the other hand, liposome adsorption on sulfonated poly(styrene) (SPS) surfaces was minimal, due to electrostatic repulsion between the negatively charged liposomes and the SPS-coated surface. Surfaces coated with m-dPEG acid were also found to resist liposome adsorption. We exploited these results to create arrays of lipid bilayers by exposing PDAC, PAH and m-dPEG patterned substrates to DOPA/DOPC vesicles of various compositions. The patterned substrates were created by stamping PDAC (or PAH) on SPS-topped multilayers, and m-dPEG acid on PDAC-topped multilayers, respectively. This technique can be used to produce functional biomimetic interfaces for potential applications in biosensors and biocatalysis, for creating arrays that could be used for high-throughput screening of compounds that interact with cell membranes, and for probing, and possibly controlling, interactions between living cells and synthetic membranes.     

Deposition of a thin film of TiOx from a titanium metal target as novel blocking layers at conducting glass/TiO2 interfaces in ionic liquid mesoscopic TiO2 dye-sensitized solar cells

In dye-sensitized TiO2 solar cells, charge recombination processes at interfaces between fluorine-doped tin oxide (FTO), TiO2, dye, and electrolyte play an important role in limiting the photon-to-electron conversion efficiency. From this point of view, a high work function material such as titanium deposited by sputtering on FTO has been investigated as an effective blocking layer for preventing electron leakage from FTO without influencing electron injection. X-ray photoelectron spectroscopy analysis indicates that different species of Ti (Ti4+, Ti3+, Ti2+, and a small amount of Ti0) exist on FTO. Electrochemical and photoelectrochemical measurements reveal that thin films of titanium species, expressed as TiOx, work as a compact blocking layer between FTO and TiO2 nanocrystaline film, improving Voc and the fill factor, finally giving a better conversion efficiency for dye-sensitized TiO2 solar cells with ionic liquid electrolytes.     

Adsorption of organic molecules on rutile TiO2 and anatase TiO2 single crystal surfaces

The interaction of organic molecules with titanium dioxide surfaces has been the subject of many studies over the last few decades. Numerous surface science techniques have been utilised to understand the often complex nature of these systems. The reasons for studying these systems are hugely diverse given that titanium dioxide has many technological and medical applications. Although surface science experiments investigating the adsorption of organic molecules on titanium dioxide surfaces is not a new area of research, the field continues to change and evolve as new potential applications are discovered and new techniques to study the systems are developed. This tutorial review aims to update previous reviews on the subject. It describes experimental and theoretical work on the adsorption of carboxylic acids, dye molecules, amino acids, alcohols, catechols and nitrogen containing compounds on single crystal TiO(2) surfaces.     

Human serum albumin adsorption on TiO2 from single protein solutions and from plasma

In the present work, the adsorption of human serum albumin (HSA) on commercially pure titanium with a titanium oxide layer formed in a H(2)O(2) solution (TiO(2) cp) and on TiO(2) sputtered on Si (TiO(2) sp) was analyzed. Adsorption isotherms, kinetic studies, and work of adhesion determinations were carried out. HSA exchangeability was also evaluated. Surface characterization was performed by atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and wettability studies. The two TiO(2) surfaces have very distinct roughnesses, the TiO(2) sp having a mean R(a) value 14 times smaller than the one of TiO(2) cp. XPS analysis revealed consistent peaks representative of TiO(2) on sputtered samples as well as on Ti cp substrate after 48 h of H(2)O(2) immersion. Nitrogen was observed as soon as protein was present, while sulfur, present in disulfide bonds in HSA, was observed for concentrations of protein higher than 0.30 mg/mL. The work of adhesion was determined from contact angle measurements. As expected from the surface free energy values, the work of adhesion of HSA solution is higher for the TiO(2) cp substrate, the more hydrophilic one, and lower for the TiO(2) sp substrate, the more hydrophobic one. The work of adhesion between plasma and the substrates assumed even higher values for the TiO(2) cp surface, indicating a greater interaction between the surface and the complex protein solutions. Adsorption studies by radiolabeling of albumin ((125)I-HSA) suggest that rapid HSA adsorption takes place on both surfaces, reaching a maximum value after approximately 60 min of incubation. For the higher HSA concentrations in solution, a multilayer coverage was observed on both substrates. After the adsorption step from single HSA solutions, the exchangeability of adsorbed HSA molecules by HSA in solution was evaluated. The HSA molecules adsorbed on TiO(2) sp seem to be more easily exchanged by HSA itself than those adsorbed on TiO(2) cp after 24 h. In contrast, after 72 h, nearly all the adsorbed albumin molecules effectively exchange with other albumin molecules.     

Adsorption and conformation behavior of biotinylated fibronectin on streptavidin-modified TiO(X) surfaces studied by SPR and AFM

It is well-known that protein-modified implant surfaces such as TiO(2) show a higher bioconductivity. Fibronectin is a glycoprotein from the extracellular matrix (ECM) with a major role in cell adhesion. It can be applied on titanium oxide surfaces to accelerate implant integration. Not only the surface concentration but also the presentation of the protein plays an important role for the cellular response. We were able to show that TiO(X) surfaces modified with biotinylated fibronectin adsorbed on a streptavidin-silane self-assembly multilayer system are more effective regarding osteoblast adhesion than surfaces modified with nonspecifically bound fibronectin. The adsorption and conformation behavior of biotinylated and nonbiotinylated (native) fibronectin was studied by surface plasmon resonance (SPR) spectroscopy and atomic force microscopy (AFM). Imaging of the protein modification revealed that fibronectin adopts different conformations on nonmodified compared to streptavidin-modified TiO(X) surfaces. This conformational change of biotinylated fibronectin on the streptavidin monolayer delivers a fibronectin structure similar to the conformation inside the ECM and therefore explains the higher cell affinity for these surfaces.     

钛白粉载体对选择性催化还原脱硝催化剂性能的影响

钛白粉(TiO2)是钒钛类选择性催化还原(SCR)脱硝催化剂的载体,TiO2的晶型、比表面积、粒度、孔结构以及SO42-和P2O5含量直接影响所制备的SCR催化剂的性能。一般而言,TiO2的比表面积越大,以其制备的SCR催化剂的比表面积也越大,活性也较高;但对于纳米级TiO2,由于颗粒粒径太小,容易发生烧结,而且形成钒钛化合物,导致催化剂比表面积较载体明显下降,因而活性降低。锐钛型TiO2由于比表面积大和不易被硫化,较金红石型TiO2适合做载体。多孔结构的TiO2使得钒物种在载体表面处于高度分散状态,从而提高催化剂的活性。TiO2中本身含有的少量SO42-和P2O5有助于提高催化剂的性能。     

Synthesis of TiO2 nanoparticles on the Au(111) surface

The growth of titanium oxide nanoparticles on reconstructed Au(111) was investigated by scanning tunneling microscopy and x-ray photoelectron spectroscopy. Ti was deposited by physical-vapor deposition at 300 K. Regular arrays of titanium nanoparticles form by preferential nucleation of Ti at the elbow sites of the herringbone reconstruction. The titanium oxide nanoclusters were synthesized by subsequent exposure to O(2) at 300 K. Two-and three-dimensional titanium oxide nanocrystallites form during annealing in the temperature range from 600 to 900 K. At the same time, the Au(111) surface assumes a serrated 110-oriented step-edge morphology suggesting step-edge pinning by titanium oxide nanoparticles. The oxidation state of the titanium oxide nanoparticles varies with annealing temperature. Specifically, annealing to 900 K results in the formation of stoichiometric TiO(2) nanocrystals as judged by the Ti(2p) binding energies measured in the x-ray photoelectron data. The nanodispersed TiO(2) on Au(111) is an ideal system to test the various models proposed for the enhanced catalytic reactivity of supported Au nanoparticles.     

共沉淀法制备氧化硅改性的纳米二氧化钛及其性质

采用共沉淀法合成了氧化硅改性的具有高比表面积的纳米二氧化钛.氧化硅的添加提高了二氧化钛纳米颗粒的热稳定性能,有效地抑制了纳米二氧化钛的颗粒增长、团聚和锐钛向金红石的晶型转换.光催化降解亚甲基蓝证明,样品具有较高的光催化活性,而且随着氧化硅添加量的增加,光催化活性提高.     

Titania-silver and alumina-silver composite nanoparticles: novel, versatile synthesis, reaction mechanism and potential antimicrobial application

Titania-silver (TiO(2)-Ag) and alumina-silver (Al(2)O(3)-Ag) composite nanoparticles were synthesised by a simple, reproducible, wet chemical method under ambient conditions. The surface of the oxides was modified with oleic acid, which acted as an intermediate between the oxide surface and the silver nanoparticles. The resulting composite nanoparticles were thoroughly characterised by XRD, TEM, XPS, FTIR and TGA to elucidate the mode of assembly of Ag nanoparticles on the oxide surfaces. Epoxy nanocomposites were formulated with TiO(2)-Ag and Al(2)O(3)-Ag to examine potential applications for the composite nanoparticles. Preliminary results from disc diffusion assays against Escherichia coli DH5α and Staphylococcus epidermidis NCIMB 12721 suggest that these TiO(2)-Ag and Al(2)O(3)-Ag composite nanoparticles have potential as antimicrobial materials.     

Induction heating for surface triggering styrene polymerization on titanium modified with ATRP initiator

Titanium and its alloys present high interests for technological applications due to their high corrosion resistance, mechanical properties and biocompatibility. In combination with these remarkable characteristics, some Ti applications require specific surface properties that can be imparted with suitable surface functionalizations of the TiO(2) oxide layer. The present work aims to study the surface-initiated ATR polymerization of styrene on titanium substrates, using grafted 11-(2-bromoisobutyrate)-undecyl-1-phosphonic acid as initiator and to compare the impact of two different heating ways on the efficiency of this polymerization: induction vs. conventional heating. The ability of the initiator to bind titanium substrates and act as an initiator for ATRP of styrene is investigated: both heating conditions led to the polymerization of styrene on modified titanium substrates. However, induction heating appeared to be much more efficient than conventional heating, leading to the formation of a thicker, much denser polystyrene layer than conventional heating after only 1h of polymerization.     

Theory of oxides surfaces, interfaces and supported nano-clusters

Oxides surfaces and thin films are finding continuous new technological applications and represent an important class of systems in materials science. Today we assist to a considerable effort to characterize the surfaces and the interfaces of oxide materials at an atomistic level. The intense experimental activity in this field has stimulated a parallel computational activity based on high-quality first principle calculations. In this review we focus our attention on the properties of oxide surfaces, and we describe the main factors that contribute to determine their behaviour: (1) nature of the bonding and electronic structure of the oxide; (2) surface morphology and defectivity; (3) doping and functionalization; (4) redox properties; (5) nano-dimensionality (e.g. in ultra-thin films). We also show how each of these parameters can affect the properties of supported metal atoms and nano-particles.     

Atomistic mechanism of charge separation upon photoexcitation at the dye-semiconductor interface for photovoltaic applications

Charge separation in excited states upon visible light absorption is a central process in photovoltaic solar cell applications. Employing state-of-the-art first principles calculations based on time-dependent density functional theory (TDDFT), we simulate electron-hole dynamics in real time and illustrate the microscopic mechanism of charge separation at the interface between organic dye molecules and oxide semiconductor surfaces in dye-sensitized solar cells. We found that electron-hole separation proceeds non-adiabatically on an ultrafast timescale <100 fs at an anthocyanin/TiO(2) interface, and it is strongly mediated by the vibrations of interface Ti-O bonds, which anchor the dye onto the TiO(2) surface. The obtained absorption spectrum and electron injection timescale agree with experimental measurements.     

Ordering of TiO2-based nanostructures on SrTiO3(001) surfaces

A class of nanostructured surface phases on SrTiO3(001) is reported and characterized through atomic-resolution scanning tunneling microscopy and Auger electron spectroscopy. These surface phases are created via argon ion sputtering and UHV annealing and form close-packed domains of highly ordered nanostructures. Depending on the type of nanostructures present, the domain ordering exhibit either (6 x 2), (9 x 2), (12 x 2), (6 x 8), or (7 x 4) surface patterning. The nanostructures are composed of TiO2-derived complexes surrounded by a TiO2 surface termination. Such surface ordering phenomena introduce another level of complexity in the chemistry of perovskite oxide surfaces and provide a basis from which potential photocatalytic and molecular-ordering applications may be developed.     

Physicochemical characterization of an anatase TiO2 surface and the adsorption of a nonionic surfactant: an atomic force microscopy study

Atomic force microscopy was used to characterize an anatase TiO2 surface, prepared by the helical vapor preparation method. The forces between two bare TiO2 surfaces were measured in the presence of water at various pH values. This TiO2 isoelectric point (iep) was characterized by the presence of only a van der Waals attraction and was measured at pH 5.8; this value is similar to that for a rutile TiO2 surface. The adsorption mechanism of a nonionic surfactant molecule to this anatase TiO2 surface was investigated by measuring the forces between two such TiO2 surfaces at their iep pH in the presence of linear dodecanol tetraethoxylate (C12E4), a poly(ethoxylene oxide) n-alkyl ether. C12E4 was seen by the presence of steric forces to adsorb to the uncharged TiO2 surface. For low surfactant concentrations, C12E4 adsorbed with its hydrophobic tail facing the TiO2 substrate, to reduce its entropically unfavorable contacts with water. Additional surfactant adsorption occurred at higher surfactant concentrations by the hydrophobic and hydrophilic interactions between the surfactant tails and heads, respectively, and gave sub-bilayers. A two-step adsorption isotherm was subsequently proposed with four regions: (1) submonolayer, (2) complete monolayer, (3) sub-bilayer, and (4) bilayer. The absence of a long-range repulsive force between the two TiO2 surfaces in the presence of the C12E4 surface aggregates indicated that a C12E4 nonionic surfactant aggregate did not possess charge.     

Spontaneous immobilization of liposomes on electron-beam exposed resist surfaces

We have found an interesting immobilization technique of liposomes on electron-beam exposed resist surfaces. The immobilized liposomes have been visualized by the atomic force microscope and have shown well-organized three-dimensional physical structures, in which the liposomes maintain their shapes and sizes similar to those of the original design in prepared solution. The immobilization is based on a strong static charge interaction between the resist surface and the liposomes. Further experiments show that very strong charge in the surfaces produces the firm immobilization of the liposome. We believe these findings can be related to various liposome applications such as drug delivery system, electrochemical or biosensors, and nanoscale membrane function studies.     

Hierarchical interlinked structure of titanium oxide nanofibers

A novel hierarchical interlinking structure of titanium oxide nanofibers with high surface area has been prepared by a soft hydrothermal chemical process via the reactions of amorphous TiO2 gel (or commercial TiOSO4 particles) and NaOH solution.     

Island organization of TiO2 hierarchical nanostructures induced by surface wetting and drying

We report on the reorganization and bundling of titanium oxide nanostructured layers, induced by wetting with different solvents and subsequent drying. TiO(2) layers are deposited by pulsed laser deposition and are characterized by vertically oriented, columnar-like structures resulting from assembling of nanosized particles; capillary forces acting during evaporation induce bundling of these structures and lead to a micrometer-size patterning with statistically uniform islands separated by channels. The resulting surface is characterized by a hierarchical, multiscale morphology over the nanometer-micrometer length range. The structural features of the pattern, i.e., characteristic length, island size, and channel width, are shown to depend on properties of the liquid (i.e., surface tension) and thickness and density of the TiO(2) layers. The studied phenomenon permits the controlled production of multiscale hierarchically patterned surfaces of nanostructured TiO(2) with large porosity and large surface area, characterized by superhydrophilic wetting behavior without need for UV irradiation.     

Titanium dioxide nanoparticles-coated column for capillary electrochromatographic separation of oligopeptides

A novel column made through the condensation reaction of TiO2 nanoparticles (TiO2 NPs) with silanol groups of the fused-silica capillary is described. EOF measurements under various buffer constitutions were used to monitor the completion of reactions. The results indicated that the EOF was dependent on the interactions between buffers and the bonded TiO2 NPs. With formate/Tris buffer, EOF reversal at pH below 5 and cathodic EOF at pH above 5 were indicated. The pI of the bonded TiO2 NPs was found at approximately ph 5. Only cathodic EOF was illustrated by substituting the mobile phase with either glutamate or phosphate buffer. It was elucidated that both glutamate and phosphate buffer yield a negative charge layer on the surface of TiO2 NPs attributable to the formation of a titanium complex. The CEC performance of the column was tested with angiotensin-type oligopeptides. Some parameters that would affect the retention behavior were investigated. The interactions between the bonded phases and the analytes were explicated by epitomized acid-base functional groups of the oligopepetides and the speciation of the surface oxide in different pH ranges. The average separation efficiencies of 3.1 x 10(4) plates/m is readily achieved with a column of 70 cm (50 cm) x 50 mum ID under an applied voltage of 15 kV, phosphate buffer (pH 6.0, 40 mM), and UV detection at 214 nm.     

Low-cost synthesis of titanium dioxide anatase nanoclusters as advanced materials for hydrogen photoproduction

Research on Chemical Intermediates - Sub-nm titanium dioxide (TiO2) clusters are synthesized via the hydrolysis of TiCl4 in order to produce clean and surfactant-free oxide surfaces. By controlling...