A combinatorial approach to the study of particle size effects on supported electrocatalysts: oxygen reduction on gold

A novel high-throughput technique has been developed for the investigation of the influence of supported metal particle size and the support on electrocatalytic activity. Arrays with a gradation of catalyst particle sizes are fabricated in a physical vapor deposition system that also allows selection of the support material. Simultaneous electrochemical measurements at all electrodes in the array, together with determination of the actual particle size distribution on each of the electrodes by transmission electron microscopy (TEM), then allows rapid determination of the activity as a function of catalyst center size. The procedure is illustrated using data for the reduction of oxygen on gold nanoparticles supported on both substoichiometric titanium dioxide (TiO(x)()) and carbon and the conclusions are verified using voltammetry at rotating disk electrodes. Gold centers with diameters in the range 1.4-6.3 nm were investigated and it is demonstrated that, with both supports, the catalytic activity for oxygen reduction decays rapidly for particle sizes below 3.0 nm. This may be observed as a decrease in current at constant potential or an increase in the overpotential for oxygen reduction.     

Catalytic activity of platinum nanoparticles on highly boron-doped and 100-oriented epitaxial diamond towards HER and HOR

Platinum nanoparticles supported on boron-doped single-crystalline diamond surfaces were used as a model system to investigate the catalytic activity with respect to the influence of particle morphology, particle density and surface preparation of the diamond substrates. We report on the preparation, characterization and activity regarding hydrogen evolution reaction (HER) and hydrogen oxidation reaction (HOR) of these Pt/diamond electrodes. Two kinds of diamond layers with boron doping above 10(20) cm(-3) were grown epitaxially on (100)-oriented diamond substrates; post-treatments of wet chemical oxidation and radio frequency (rf) oxygen plasma treatments were applied. Electrochemical deposition of Pt was performed using a potentiostatic double-pulse technique, which allowed variation of the particle size in the range between 1 nm and 15 nm in height and 5 nm and 50 nm in apparent radius, while keeping the particle density constant. Higher nucleation densities on the plasma processed surface at equal deposition parameters could be related to the plasma-induced surface defects. Electrochemical characterization shows that the platinum particles act as nanoelectrodes and form an ohmic contact with the diamond substrate. The catalytic activity regarding HER and HOR of the platinum nanoparticles exhibits no dependence on the particle size down to particle heights of ～1 nm. The prepared Pt on diamond(100) samples show a similar platinum-specific activity as bulk platinum. Therefore, while keeping the activity constant, the well-dispersed particles on diamond offer an optimized surface-to-material ratio.     

Size-controlled synthesis of colloidal platinum nanoparticles and their activity for the electrocatalytic oxidation of carbon monoxide

Using polyvinylpyrrolidone (PVP) as a stabilizing agent, stable colloidal solutions of platinum nanoparticles of different size distributions have been prepared by reducing H2PtCl6 with hydrogen. The UV-vis adsorption peaks at 258 nm due to the adsorption of Pt(IV) species disappear completely, indicating that the Pt(IV) species has been used up and colloidal Pt has been formed. The electrodes have been prepared from aqueous Pt colloids and glassy carbon (GC). The effect of platinum particle size of Pt/GC catalyst electrode on the electrocatalytic oxidation of carbon monoxide has been investigated. The voltammetry shows that a higher potential is needed for the oxidation of absorbed carbon monoxide with a decrease of the platinum particle size for particle sizes larger than 1 nm. But for particle sizes smaller than 1 nm, the potential remains constant while the activity decreases with decreasing the size. The snowlike, well-dispersed, and highly ordered platinum nanoparticles demonstrate high activity in the oxidation reaction of carbon monoxide. The reason may be due to the geometric structure of platinum nanoparticles.     

Electronic and chemical properties of supported Au nanoparticles

Oxidation and reduction behaviors of Au nanoparticles with different sizes on highly ordered pyrolytic graphite (HOPG) and silica were studied using X-ray photoelectron spectroscopy (XPS). For Au nanoparticles smaller than 6 nm in diameter, we found a novel oxygen species formed in Au nanoparticles, which is absent in larger particles and Au bulk crystals. This new oxygen species is attributed to the subsurface oxygen: for a complete understanding of the structures of catalytically active Au, the new oxygen species should be taken into account. In this context, it is worth mentioning that the subsurface oxygen species has been suggested to play an important role in heterogeneous catalysis. With decreasing Au particle size, a positive core level shift can be observed, which can be mostly attributed to the final state effects. Increase of the number of undercoordinated atoms with decreasing particle size is evidenced by a reduced splitting between 5d_3/2 and 5d_5/2 states and a band narrowing. Our results on electronic structures of Au nanoparticles on silica are compared to those on other substrates such as zirconia and titania to shed light onto the metal-support interactions.     

Thermal-induced growth of gold nanoparticles conjugated with thermoresponsive polymer without chemical reduction

The growth of gold nanoparticles without chemical reduction of gold (III) ions was achieved by the disruption of thermoresponsive polymers conjugated with the gold nanoparticles through the phase transition of the polymers. When a solution of gold nanoparticles coated with thermoresponsive polymers was heated, chains of the thermoresponsive polymers were disrupted because of dehydration, resulting in the fusion of gold nanoparticles to form larger nanoparticles. The evolution of the extinction band around 550 nm evidenced the formation of these large (post-fusion) gold nanoparticles, which were characterized by transmission electron microscope (TEM) and dynamic light scattering (DLS). TEM images verified the formation of the large gold nanoparticles having particle sizes of 80-100 nm, whereas DLS indicated the existence of large nanoparticles with hydrodynamic diameters exceeding 200 nm. The deposition did not require the addition of reductants or trivalent gold ions for the formation of the large gold nanoparticles. Both the heating and the solution conditions were studied to elucidate the mechanism of the formation of large gold nanoparticles.     

Oxygen reduction at platinum monolayer islands deposited on Au(111)

Atomic monolayer islands of Pt, namely, two-dimensional Pt nanoparticles, on a Au(111) electrode have been studied for the first time, focusing on their electrocatalytic activities for oxygen reduction in acid solutions. The Pt islands' electrodes were prepared using the self-assembled technique of thiols together with the replacement of Pt with a Cu monolayer. The states of adsorbed OH and the catalytic activities of oxygen reduction were sensitive to the Pt island size. As island size decreased, a delay in the reduction of surface oxide was observed. However, negligible influence of adsorbed OH on activity for oxygen reduction was observed. Pt islands of sizes ranging from 5 to 10 nm showed higher specific catalytic activities for oxygen reduction. Specific catalytic activities decreased by a factor of 10 with a decrease in island sizes from 5.5 to 3.1 nm. Size effects observed in Pt monolayer islands were discussed in comparison with three-dimensional nanoparticles, to obtain information concerning the size effects of metal nanoparticles.     

Size dependent catalysis with CTAB-stabilized gold nanoparticles

CTAB-stabilized gold nanoparticles were synthesized by applying the seeding-growth approach in order to gain information about the size dependence of the catalytic reduction of p-nitrophenol to p-aminophenol with sodium borohydride. Five different colloidal solutions of stabilized gold nanoparticles have been characterized by TEM, AFM, UV-Vis, SAXS, and DLS for their particle size distributions. Gold nanoparticles (mean sizes: 3.5, 10, 13, 28, 56 nm diameter) were tested for their catalytic efficiency. Kinetic data were acquired by UV-Vis spectroscopy at different temperatures between 25 and 45 °C. By studying the p-nitrophenol to p-aminophenol reaction kinetics we determined the nanoparticle size which is needed to gain the fastest conversion under ambient conditions in the liquid phase. Unexpectedly, CTAB-stabilized gold nanoparticles with a diameter of 13 nm are most efficient.     

Hybrid gold-nanoparticle-cored conjugated thiophene dendrimers: synthesis, characterization, and energy-transfer studies

A series of hybrid Au-nanoparticle-dendrimer materials: nanoparticle-cored thiophene dendrimers (NCTDs) were synthesized, characterized, and investigated for their energy-transfer properties. These hybrid nanoparticles were obtained by the simultaneous and in situ reduction of gold(III) chloride and self-assembly of the thiol-containing thiophene dendritic ligands. The dendron ligands were radially attached to the gold nanoparticles and were analyzed by TEM, UV/Vis, (1)H NMR, and FTIR spectroscopies. The solution fluorescence of the attached thiophene dendrons are quenched progressively. Both alkyl-chain length and dendron size have significant influence on the energy-transfer efficiency, as well as on core sizes and size distribution of the Au nanoparticles. In spite of the phenomenon's dependence on nanoparticle size, the energy transfer generally follows the 1/d(2) distance dependence. Single NCTD nanoparticles were also adsorbed on highly ordered pyrolytic graphite (HOPG) and uniform aggregates were observed on mica flat substrates.     

Observing Single Hollow Porous Carbon Catalyst Collisions for Oxygen Reduction at Gold Nanoband Electrode

The evaluation of single carbon particle catalysts is critical to better understand the relationship between structure and properties. Here, we use an electrochemical collision method to study the electrocatalytic behaviour of single hollow porous carbon catalyst on gold nanoband electrodes (AuNBE). We observed the catalytic current of oxygen reduction of single carbon particle and quantified the contribution of the porous structure to the catalytic performance. We find that the meso/microporous and hollow structures contribute to the electrocatalytic current. Our research provides direct evidence that the hollow/porous structures improve the electrocatalytic performance.     

pH值对微波协助乙二醇法制备PtRu/C催化剂的影响

以微波协助乙二醇工艺合成了碳负载不同粒径大小的PtRu/C纳米催化剂, 主要考察了溶液pH值对PtRu粒子大小的影响. 利用紫外可见光谱、能量散射X射线谱、透射电镜和X射线衍射谱对PtRu纳米催化剂进行了表征. 结果表明, pH值是一个对PtRu粒子大小有着重要影响的因素. TEM结果显示随着溶液pH值的增加, PtRu粒径从3.5 nm减小到1.5 nm. 当溶液pH值达到11.0时, 由于金属粒子被保护, 合成的催化剂中金属载量明显减少. 溶液pH 值在9.0 右合成的PtRu/C催化剂具有适宜粒径(2.4 nm)和均匀分布的金属颗粒, 具有最好的甲醇电氧化活性.     

Bimodal Size Distribution of Gold Nanoparticles under Picosecond Laser Pulses

The evolution of size distributions of gold nanoparticles under pulsed laser irradiation (Nd:YAG, lambda = 355 nm, pulse width 30 ps) was carefully observed by transmission electron microscopy. Interestingly, the initial monomodal size distribution of gold nanoparticles turned into a bimodal one, with two peaks in the number of particles, one at 6 nm and the other at 16-24 nm. The sizes for small particles depended very little on the irradiated laser energy. This change is attributed to laser-induced size reduction of the initial gold nanoparticles followed by the formation of small particles. In our analysis, we extracted a characteristic value for the size-reduction rate per one pulse and revealed that laser-induced size reduction of gold nanoparticles occurred even below the boiling point. When laser energy is insufficient for the boiling of particles, formation of gold vapor around liquid gold drops is thought to cause the phenomenon. With enough laser energy for the boiling, the formation of gold vapor around and inside liquid gold drops is responsible for the phenomenon. We also observed particles with gold strings after one pulse irradiation with a laser energy of 43 mJ cm(-2) pulse(-1), which is sufficient energy for the boiling. It is considered that such particles with gold strings are formed by the projection of gaseous gold from liquid gold drops with some volume of liquid gold around the bubble. On the basis of comparison with previous work, picosecond laser pulses are thought to be the most efficient way to cause laser-induced size reduction of gold nanoparticles.     

Extinction coefficient of gold nanoparticles with different sizes and different capping ligands

Extinction coefficients of gold nanoparticles with core size ranging from approximately 4 to 40 nm were determined by high resolution transmission electron microscopy analysis and UV-vis absorption spectroscopic measurement. Three different types of gold nanoparticles were prepared and studied: citrate-stabilized nanoparticles in five different sizes; oleylamide-protected gold nanoparticles with a core diameter of 8 nm, and a decanethiol-protected nanoparticle with a diameter of around 4 nm. A linear relationship between the logarithms of extinction coefficients and core diameters of gold particles was found independent of the capping ligands on the particle surface and the solvents used to dissolve the nanoparticles. This linear relation may be used as a calibration curve to determine the concentration or average size of an unknown nanoparticle or nanoparticle-biomolecule conjugate sample.     

Electrocatalytic hydrogen redox chemistry on gold nanoparticles

Electrocatalytic proton reduction leading to the formation of adsorbed molecular hydrogen on gold nanoparticles of 1-3 and 14-16 nm diameter stabilized by 1-mercapto-undecane-11-tetra(ethyleneglycol) has been demonstrated by cyclic voltammetry using a hanging mercury drop electrode. The nanoparticles were adsorbed to the electrode from aqueous dispersion and formed robust surface layers transferrable to fresh base electrolyte solutions. Unique electrocatalytic proton redox chemistry was observed that has no comparable counterpart in the electrochemistry of bulk gold electrodes. Depending on size, the nanoparticles have a discrete number of electrocatalytically active sites for the two-electron/two-proton reduction process. The adsorbed hydrogen formed is oxidized with the reverse potential sweep. These findings represent a new example of qualitative different behavior of nanoparticles in comparison with the corresponding bulk material.     

MOF-Mediated Fabrication of a Porous 3D Superstructure of Carbon Nanosheets Decorated with Ultrafine Cobalt Phosphide Nanoparticles for Efficient Electrocatalysis and Zinc–Air Batteries

Superstructures have attracted great interest owing to their potential applications. Herein, we report the first scalable preparation of a porous nickel-foam-templated superstructure of carbon nanosheets decorated with ultrafine cobalt phosphide nanoparticles. Uniform two-dimensional (2D) Co-metal organic framework (MOF) nanosheets (Co-MNS) grow on nickel foam, followed by a MOF-mediated tandem (carbonization/phosphidation) pyrolysis. The resulting superstructure has a porous 3D interconnected network with well-arranged 2D carbon nanosheets on it, in which ultrafine cobalt phosphide nanoparticles are tightly immobilized. A single piece of this superstructure can be directly used as a self-supported electrode for electrocatalysis without any binders. This “one-piece” porous superstructure with excellent mass transport and electron transport properties, and catalytically active cobalt phosphide nanoparticles with ultrasmall size (3–4 nm), shows excellent trifunctional electrocatalytic activities for oxygen evolution reaction (OER), hydrogen evolution reaction (HER), and oxygen reduction reaction (ORR), achieving great performances in water splitting and Zn–air batteries.     

Dendrimer-rhodium nanoparticle modified glassy carbon electrode for amperometric detection of hydrogen peroxide

Metallic nanoparticles of rhodium were prepared by using the newly synthesized N,N-bis-succinamide-based dendrimer as stabilizers. The Rh nanoparticles were spherical shaped with a particle size of ∼2 nm. The dendrimer Rh-encapsulated nanoparticles (Rh-DENs) were immobilized on glassy carbon electrode (GCE) and their electrocatalytic activity towards hydrogen peroxide reduction was investigated using cyclic voltammetry and chronoamperometry. The Rh-DENs modified GCE showed excellent electrocatalytic activity for hydrogen peroxide reduction reactions. The steady-state cathodic current response of the modified electrode at −0.3 V (vs SCE) in phosphate buffer (pH 7.0) showed a linear response to hydrogen peroxide concentration ranging from 8 to 30 μM with a detection limit and sensitivity of 5 μM and 0.03103 × 10⁻⁶ A μM⁻¹, respectively.     

In Situ Fabrication of Noble Metal Nanoparticles Modified Multiwalled Carbon Nanotubes and Related Electrocatalysis

Using multiwalled carbon nanotubes (MWNTs) as templates, noble metal (Au, Ag, Pt or Pd) nanoparticles (NPs) were fabricated in situ by electrochemistry with a diameter of 40–60 nm. Further, catalytic behaviors of these composite materials were investigated. Experiments showed that such carbon nanotubes decorated with Pd NPs modified glassy carbon electrodes exhibited higher electrocatalytic ability to some molecules such as evolution of hydrogen, reduction of oxygen and oxidation of ascorbic acid. Atomic force microscopy, X‐ray photoelectron spectroscopy and cyclic voltammetry were used to characterize the film formation and their properties.     

Deposition of gold nanoparticles onto thiol-functionalized multiwalled carbon nanotubes

Gold nanoparticles were deposited on the surface of multiwalled carbon nanotubes (MWNTs) functionalized with aliphatic bifunctional thiols (1,4-butanedithiol, 1,6-hexanedithiol, 1,8-octanedithiol, and 2-aminoethanethiol) through a direct solvent-free procedure. Small gold particles, with a narrow particle size distribution around 1.7 nm, were obtained on 1,6-hexanedithiol-functionalized MWNTs. For MWNTs functionalized with the aminothiol, the average Au particle size was larger, 5.5 nm, apparently due to a coalescence phenomenon. Gatan image filter (GIF) observations show that sulfur is at the nanotube surface with a non-homogeneous distribution. A higher sulfur concentration was observed around the gold nanoparticles' location.     

The electrooxidation of small organic molecules on platinum nanoparticles supported on gold: influence of platinum deposition procedure

The electrocatalytic properties of small platinum nanoparticles were investigated for the oxidation of CO, methanol, and formic acid using voltammetry, chronoamperometry, and surface-enhanced Raman spectroscopy. The particles were generated by galvanostatic deposition of platinum on a polished gold surface from an H₂PtCl₆ containing electrolyte and ranged between 10 and 20 nm in diameter for low platinum surface concentrations, 10 and 120 nm for medium concentrations, and full Pt monolayers for high concentrations. CO stripping and bulk CO oxidation experiments on the particles up to 120 nm in diameter displayed pronounced structural effects. The CO oxidation current-time transients show a current decay for low platinum coverages and a current maximum for medium and high coverages. These results were also observed in the literature for particles of 2- to 5-nm size and agglomerates of these particles. The similarities between the literature and our results, despite large differences in particle size and morphology, suggest that particle structure and morphology are also very important catalytic parameters. Surface-enhanced Raman spectroscopy data obtained for the oxidation of CO on the Pt-modified Au electrodes corroborate this conclusion. A difference in the ratio between CO adsorbed in linear- and bridge-bonded positions on the Pt nanoparticles of different sizes demonstrates the influence of the surface morphology. The oxidation activity of methanol was found to decrease with the particle size, while the formic acid oxidation rate increases. Again, a structural effect is observed for particles of up to ca. 120 nm in diameter, which is much larger than the particles for which a particle size effect was reported in the literature. The particle shape effect for the methanol oxidation reaction can be explained by a reduction in available “ensemble sites” and a reduction in the mobility of CO formed by decomposition of methanol. As formic acid does not require Pt ensemble sites, decreasing the particle size, and thus, the relative number of defects, increases the reaction rate. Dedicated to Prof. Dr. Teresa Iwasita on the occasion of her 65th birthday in recognition of her numerous contributions to interfacial electrochemistry.     

电化学方法制备高分散Pt/CMK-3及其对甲醇电化学催化性能

采用直接电化学还原法在介孔碳(CMK-3)载体上直接电沉积高分散的铂纳米颗粒,制备CMK-3复合铂纳米颗粒电极(Pt/CMK-3)。 通过透射电子显微镜分析发现,铂纳米颗粒非常均匀的分布在CMK-3上,平均粒径约5 nm。 通过循环伏安测试,分析了催化剂不同负载铂含量时氯铂酸的利用率,在理论铂质量分数为20%时,这种方法制备的Pt/CMK-3所使用的氯铂酸的利用率最高,在1 mol/L CH3OH+0.5 mol/L H2SO4溶液中循环伏安测试电流密度达到382 A/g。 在相同实验条件下,Pt/CMK-3电极对甲醇电催化活性远高于Pt/XC-72(炭黑)电极和用常规电沉积方法制备的Pt/CMK-3电极。     

pH effect on electrocatalytic reduction of CO2 over Pd and Pt nanoparticles

Adsorbed hydrogen participates in electrocatalytic reduction of CO₂ and competitive hydrogen evolution reaction (HER) simultaneously, and its reaction pathway greatly affects the activity and selectivity of CO₂ reduction. In this work, we investigate pH effect on electrocatalytic reduction of CO₂ over Pd and Pt nanoparticles (NPs) with a similar size in a pH range from 1.5 to 4.2. Pt NPs completely contribute to HER in the pH range. Over Pd NPs, Faradaic efficiency for CO production at − 1.19 V (vs. reversible hydrogen electrode) varies from 3.2% at pH of 1.5 to 93.2% at pH of 4.2, and current density for CO production reaches maximum at pH of 2.2. The significant enhancement of Faradaic efficiency and current density for CO production over Pd NPs at high pH values is attributed to decreased kinetics of hydrogen evolution reaction by increasing hydrogen binding energy and lowered adsorption affinity of CO-like intermediate compared to Pt.