不同形貌Bi4Ti3O12粒子的可控合成及光催化性能

研究了用一步水热法制备的不同形貌的钛酸铋(Bi₄Ti₃O₁₂, BIT)粒子的光学和可见光催化性能, 并对其晶体结构和微观结构用X射线衍射(XRD)、场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)和高分辨透射电子显微镜(HRTEM)等手段进行了表征. XRD结果表明, 所制备的BIT 样品为层状钙钛矿结构. FESEM结果表明, 通过控制水热过程的反应参数可以得到不同形貌的纳米粒子. 紫外-可见漫反射光谱(UV-Vis DRS)表明BIT 样品的带隙能约为2.88-2.93 eV. 利用可见光(λ>420 nm)照射下的甲基橙(MO)降解实验评价了BIT 样品的光催化性能. 结果表明, BIT 的光催化活性比掺氮TiO₂ (N-TiO₂)高得多. 研究了形貌对BIT 光催化性能的影响. 所制备的BIT纳米带光催化效率最高, 经可见光照射360 min, 甲基橙溶液的降解率可达到95.0%.     

纺锤形BiVO4微米管：低温离子熔盐合成及光催化性能

以Bi(NO₃)₃·5H₂O和NH₄VO₃为原料,以氯化胆碱和尿素组成的低温离子熔盐为反应介质,采用离子热合成法成功制备出了具有纺锤状外形的BiVO₄微米管。利用XRD,SEM,UV-Vis DRS,光催化测试等手段考察了BiVO₄颗粒的物相、形貌和光催化性能。结果表明,在离子熔盐环境下可以制备出结晶良好的BiVO₄纺锤形微米管,该BiVO₄微米管长10~15 μm,直径为1.5 μm左右,管壁厚约为200 nm。同时,研究了pH值对BiVO₄颗粒物相与形貌的影响,发现随着pH值的变化可分别合成出具有柱状、纺锤形微米管、柱状微米管和针柱状单斜相BiVO₄颗粒。光催化测试结果表明,这些单斜白钨矿BiVO₄颗粒在可见光范围都具有一定的光催化活性,其中纺锤状微米管对罗丹明B的降解效果最佳,可见光照射4.5 h后罗丹明B的降解率可达到93％。     

PW11Cu/TiO2膜光催化剂的制备及可见光催化性能

以PW₁₁Cu为可见光活性组分, TiO₂为载体结构组分, 采用溶胶-凝胶法制备了PW₁₁Cu/TiO₂复合膜可见光催化剂, 并用UV-Vis DRS、IR、Raman、XRD、SEM、TEM等手段对催化剂的光吸收性质、化学组成、晶相、表面结构和形貌进行了表征, 同时, 以模型污染物RhB的可见光降解为探针评估了它的光催化活性, 考察了膜处理温度、PW₁₁Cu含量和溶液酸性对催化活性的影响, 最后, 通过催化剂循环降解RhB试验评估了PW₁₁Cu/TiO₂膜的稳定性。实验结果表明, PW₁₁Cu/TiO₂膜对可见光有明显吸收, 低温(100 ℃)处理的膜为无定形态, 高温(500 ℃)处理的膜为多晶态;低温处理的膜具有较高的可见光催化活性, 用于RhB的可见光催化降解, 在中性条件下反应80 min, RhB的降解率为100%, TOC去除达32%(4 h);提高溶液酸性有利于催化剂活性的提高, 在pH=2.5的条件下, 达到100%的RhB降解仅需30 min。在本实验条件下, PW₁₁Cu的最佳剂量是3.0 g。经过10次循环降解RhB, 催化剂的光催化活性仍保留约90%。     

PW11Cu/TiO2膜光催化剂的制备及可见光催化性能

以PW₁₁Cu为可见光活性组分,TiO₂为载体结构组分,采用溶胶-凝胶法制备了PW₁₁Cu/TiO₂复合膜可见光催化剂,并用UV-Vis DRS、IR、Raman、XRD、SEM、TEM等手段对催化剂的光吸收性质、化学组成、晶相、表面结构和形貌进行了表征,同时,以模型污染物RhB的可见光降解为探针评估了它的光催化活性,考察了膜处理温度、PW₁₁Cu含量和溶液酸性对催化活性的影响,最后,通过催化剂循环降解RhB试验评估了PW₁₁Cu/TiO₂膜的稳定性。实验结果表明,PW₁₁Cu/TiO₂膜对可见光有明显吸收,低温(100℃)处理的膜为无定形态,高温(500℃)处理的膜为多晶态;低温处理的膜具有较高的可见光催化活性,用于RhB的可见光催化降解,在中性条件下反应80 min,RhB的降解率为100%,TOC去除达32%(4 h);提高溶液酸性有利于催化剂活性的提高,在pH=2.5的条件下,达到100%的RhB降解仅需30 min。在本实验条件下,PW₁₁Cu的最佳剂量是3.0 g。经过10次循环降解RhB,催化剂的光催化活性仍保留约90%。     

层状、花形和棒状钛酸铋纳米结构的可控合成及光催化性能

通过可控水热法,制备出层状、花形和棒状钛酸铋(Bi₄Ti₃O₁₂,BIT)纳米结构。通过X射线衍射(XRD)和场发射扫描电子显微镜(FESEM)观测其结构和形貌特征。XRD图显示,所制备的样品为层状钙钛矿结构。FESEM结果表明,通过控制水热过程的反应参数可以得到不同形貌的纳米粉体。紫外-可见漫反射光谱(UV-VisDRS)表明BIT样品的带隙能约为2.63~2.95eV。利用可见光(λ>420nm)照射下的甲基橙降解实验评价了BIT样品的光催化性能。结果表明,BIT的光催化活性比掺氮TiO₂(N-TiO₂)高得多。所制备的层状BIT纳米结构光催化效率最高,经可见光照射360min,甲基橙溶液的降解率可达95.0%。同时还研究了结构和形貌对不同条件下制备的BIT样品光催化活性的影响。     

可见光响应催化剂BiVO4六角形微米棒的水热合成

以Bi(NO₃)₃·5H₂O和NH₄VO₃为原料并以聚乙烯吡咯烷酮(PVP)为模板剂通过水热法制备了BiVO₄六角形微米棒晶体。采用XRD、SEM、IR、Raman、UV-Vis、光催化等对产品进行了表征和分析。结果表明,PVP辅助水热法能够合成直径125~300 nm、长度在1.0~1.6 μm内的形貌均一且结晶度高的单斜白钨矿BiVO₄六角形微米棒晶体。相比BiVO₄颗粒,该棒状样品的紫外-可见光吸收边发生了稍许红移,其能带隙减小至2.25 eV。光催化结果表明,添加2.0 g PVP时的BiVO₄微米棒对亚甲基蓝具有最强的可见光催化降解活性,其光照射浓度为10 mg·L^-1亚甲基蓝溶液2 h时的降解率达到99%。     

Bi2MoO6/BiVO4异质结的水热合成和可见光催化活性

采用一步水热法制备Bi₂MoO₆/BiVO₄复合光催化剂. 利用X 射线衍射(XRD)、场发射扫描电子显微镜(FESEM)、高分辨透射电子显微镜(HRTEM)等手段对其晶体结构和微观结构进行了表征. 结果表明, Bi₂MoO₆纳米粒子沉积在BiVO₄纳米片表面从而形成异质结结构. 紫外-可见漫反射光谱(UV-Vis DRS)表明所制备的Bi₂MoO₆/BiVO₄异质结较纯相Bi₂MoO₆和BiVO₄对可见光吸收更强. 由于形成异质结结构及其光吸收性能使Bi₂MoO₆/BiVO₄ 光催化活性有较大提高. 可见光下(λ>420 nm)光催化降解罗丹明B (RhB)实验结果表明,Bi₂MoO₆/BiVO₄光催化活性较纯相Bi₂MoO₆和BiVO₄高. Bi₂MoO₆/BiVO₄样品光催化性能提高的原因是Bi₂MoO₆和BiVO₄形成异质结, 从而有效抑制光生电子-空穴对的复合, 增大了可见光吸收范围及比表面积.     

盐酸溶液处理钒酸铋增强可见光催化活性及其机理

采用盐酸水溶液处理BiVO₄ 的方法获得增强的光催化活性. 在0.1 mol·L^-1 酸溶液中浸渍反应6 h,BiVO₄ 的可见光催化降解苯酚的活性提高了3.5 倍. 采用X 射线衍射(XRD), 扫描电镜(TEM)和漫反射光谱(DRS)等表征手段研究处理后样品的晶相组成和表面形貌, 结合不同酸和氯化物处理的对照实验, 结果表明,在H⁺和Cl^-的协同作用下, BiVO₄表面部分溶出并以BiOCl 沉积, 形成了表面具有凹陷沟壑的BiVO₄颗粒与片状结构BiOCl 的复合物. 采用悬浮液光电压法测定BiOCl 平带电位, 通过BiVO₄和BiOCl 的能带分析及其混合颗粒的光催化活性测试, 确证二者间不存在颗粒间电子转移效应. 增强的光催化活性主要归因于BiVO₄表面形成了有助于光生电荷迁移的凹凸不平结构. 这种表面处理方法有望成为一种增强半导体化合物光催化活性的有效途径.     

原位碳、氮共掺杂二氧化钛空心球的制备与可见光光催化性能

在H₂O₂-HF 的乙醇-水混合溶液中, 通过水热处理碳氮化钛(TiCN)制备了碳、氮共掺杂TiO₂ 空心球(CNTH). 用X 射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)、X 射线光电子能谱(XPS)和紫外-可见(UV-Vis)吸收光谱表征了所制备的样品. 在可见光(λ≥400 nm)照射下, 通过降解甲基蓝检测了碳、氮共掺杂TiO₂空心球的光催化活性. 结果表明, 源于TiCN中的部分碳和氮原子原位掺入了TiO₂的晶格中, 部分碳掺入TiO₂点阵的间隙中. 该材料在整个可见光区展示了增强的可见光吸收, 其带边明显红移. 光催化研究表明在强可见光吸收和独特的空心球结构的协同作用下, 碳、氮共掺杂TiO₂空心球展示了比P25更高的可见光光催化活性.     

Ag3PO4/BiVO4复合光催化剂的制备及可见光催化降解染料

结合回流法和原位沉淀法成功制备磷酸银/矾酸铋(Ag₃PO₄/BiVO₄)复合光催化剂. 通过X 射线衍射(XRD)、场发射扫描电子显微镜(FESEM)、能量色散X射线光谱(EDS)、紫外-可见漫反射光谱(UV-Vis DRS)及光致发光(PL)光谱对制备样品进行表征. XRD和FESEM结果表明成功制备Ag₃PO₄/BiVO₄复合光催化剂. 采用节能发光二极管灯(LED)作为可见光光源, 在低消耗光催化系统中评价制备样品可见光催化降解染料的活性.当Ag₃PO₄和BiVO₄的组成摩尔比为1:3 时, 复合Ag₃PO₄/BiVO₄光催化剂呈现出高于纯相Ag₃PO₄的催化活性,可减少Ag₃PO₄的使用量. Ag₃PO₄/BiVO₄复合光催化剂在中性溶液中表现出高活性, 同时证实其对阳离子染料的光催化降解效果强于阴离子染料. 在Ag₃PO₄/BiVO₄系统中, 超氧自由基和空穴是主要的活性物种. 经过三次循环利用, Ag₃PO₄/BiVO₄复合催化剂的可见光催化活性表现出不同程度的降低, 归因于降解过程中产生金属银.     

Visible light photocatalytic activity of BiVO4 particles with different morphologies

Bismuth vanadate (BiVO₄) particles with different morphologies were synthesized by a one-step hydrothermal process and their optical and photocatalytic properties were investigated. Their crystal structure and microstructures were characterized using X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM). XRD patterns demonstrate that the as-prepared samples are monoclinic cell. FESEM shows that BiVO₄ crystals can be fabricated in different morphologies by simply manipulating the reaction parameters of hydrothermal process. The UV–visible diffuse reflectance spectra (UV–vis DRS) reveal that the band gaps of BiVO₄ photocatalysts are about 2.07–2.21 eV. The as-prepared BiVO₄ photocatalysts exhibit higher photocatalytic activities in the degradation of rhodamine B (Rh B) under visible light irradiation (λ > 420 nm) compared with traditional N-doped TiO₂ (N-TiO₂). Furthermore, wheat like BiVO₄ sample reveals the highest photocatalytic activity. Up to 100% Rh B is decolorized after visible light irradiation for 180 min. The reason for the difference in the photocatalytic activities for BiVO₄ samples obtained at different conditions were systematically studied based on their shape, size and the variation of local structure.     

Simulated Sunlight-Driven Degradation of Rhodamine B by Porous Peanut-Like TiO2/BiVO4 Composite

Porous peanut-like TiO₂/BiVO₄ composite nanostructures were synthesized via a template-free hydrothermal process with bismuth nitrate, ammonium metavanadate and anatase TiO₂ as raw materials. The crystal structures, morphologies, and optical properties of the as-prepared samples were characterized by X-ray powder diffraction, transmission electron microscope, scanning electron microscopy, X-ray photoelectron spectroscopy and UV–visible absorption spectra. Simulated sun-light induced photocatalytic degradation of Rhodamine B by porous peanut-like TiO₂/BiVO₄ nanostructures in the absence and presence of H₂O₂ has been investigated, and the results show these porous composite nanostructures with higher photocatalytic activity than pure BiVO₄ and anatase TiO₂. When TiO₂/BiVO₄ heterostructures were used as the photocatalysts under simulated sun-light irradiation, BiVO₄ could act as a sensitizer to absorb the visible light. Meanwhile, coupling different band-gap semiconductors of TiO₂ and BiVO₄, the compound facilitate separation of the photogenerated carriers under the internal field induced by the different electronic band structures of semiconductors.     

掺镁钛酸钡纳米棒的水热合成和光催化性能

用水热法制备掺镁钛酸钡(Ba1-xMgxTiO3(x=0,0.10,0.20,0.30,0.40),BMT)纳米粉体。运用X射线衍射仪(XRD)、场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)、紫外可见漫反射光谱技术(DRS)等手段对样品进行了表征,并在可见光照射下于溶液中考察了其光催化降解甲基橙反应活性。结果表明,通过控制氢氧根浓度可以得到不同形貌的纳米粉体。基于不同条件下制备的样品的微结构分析,提出了这些不同形貌的形成机制。制备出的BMT材料的带隙能约为2.61 eV。光催化反应结果表明BMT的光催化活性比掺氮TiO2高得多。OH-浓度为8 mol·L-1时制备的BMT纳米棒光催化效率最高,经可见光照射360 min,浓度为0.01 mmol·L-1甲基橙溶液的降解率可达到93.0%,且循环使用4次后,其光催化活性并没有明显降低,表明BMT是一种稳定有效的可见光催化剂.     

高效Ag@AgBr等离子体光催化剂的制备及可见光活性研究

采用水热法和光致还原法制备了具有等离子体共振效应的Ag@AgBr可见光催化剂,利用XRD,SEM,EDX,DRS和XPS等手段对产物的结构和性能进行表征,并研究了催化剂在可见光下对罗丹明B(RhB)的光催化降解性能,考察了催化剂的循环使用及捕获剂对Ag@AgBr光催化性能的影响.结果表明:贵金属Ag纳米粒子的表面等离子体共振效应可显著增强Ag@AgBr对可见光的吸收;催化剂对罗丹明B具有较高的可见光降解活性和稳定性,在可见光下照射90 min,对罗丹明B的降解率达95%以上,光催化剂循环使用5次仍具有良好的光催化降解活性;淬灭实验表明在Ag@AgBr降解罗丹明B过程中,吸附在催化剂表面的h+、·OH、O2·-是主要的活性物种.     

Bismuth titanate pyrochlore microspheres: Directed synthesis and their visible light photocatalytic activity

Bismuth titanates, Bi₂Ti₂O₇ (BIT), with well-defined spherical structures were synthesized by a facile hydrothermal process without the use of any surfactant or template. XRD and SEM studies have shown that spheres could be fabricated in high yields by simply manipulating the concentrations of hydroxide ions. In this case, hydroxide ions seem to play a pivotal role in controlling the formation of seeds and growth rates of the BIT particles. On the basis of structural analysis of samples obtained at different concentrations of OH⁻, we also proposed a plausible mechanism to account for the formation of these distinctive morphologies under different conditions. The as-prepared BIT microspheres with good stability exhibited higher photocatalytic activities in the degradation of Rhodamine B (RhB) under visible light irradiation than that in commercial P25 TiO₂. Furthermore, the enhanced photocatalytic performance for RhB degradation was also investigated with assistance of a small amount of H₂O₂.     

铋掺杂二氧化钛纳米颗粒的制备及其可见光催化性能

采用水热法,以纳米管钛酸为前驱物制备了Bi掺杂的TiO₂,并利用X射线衍射、透射电子显微镜、X射线光电子能谱、紫外-可见漫反射光谱等手段对样品进行了表征. 以甲基橙的光催化降解为模型反应评价了样品的可见光催化性能. 结果表明,Bi离子并没有进入TiO₂的晶格中,而是以BiOCl的形式存在. 所制得的BiOCl/TiO₂复合物对甲基橙降解表现出较优越的可见光催化活性;当Bi/Ti摩尔比为1%,水热温度为130℃时,所制催化剂的光催化性能最佳,并对光催化活性提高的机理进行了讨论. 同时,该催化剂对4-氯苯酚降解也表现出较高的光催化性能.     

四角星形BiVO4/Bi2O3催化剂的制备及性能

采用水热法合成具有四角星形貌的钒酸铋,再将钒酸铋浸渍在碱溶液里二次水热,制备出BiVO_4/Bi_2O_3催化剂。采用X射线粉末衍射(XRD)、扫描电子显微镜(SEM),紫外-可见漫反射(UV-Vis DRS)等方法对样品进行表征。可见光下,BiVO_4/Bi_2O_3复合物的光催化降解罗丹明B性能及光电流响应均优于纯BiVO_4。这是由于BiVO_4/Bi_2O_3复合材料形成了异质结构,有效抑制了光生电子与空穴的复合效率。     

Synthesis of BiVO4 nanosheets-graphene composites toward improved visible light photoactivity

Two-dimensional (2-D) BiVO₄ nanosheets-graphene (GR) composites with different weight addition ratios of GR have been prepared via a facile wet chemistry process. X-ray diffraction (XRD), Raman spectra, X-ray photoelectron spectra (XPS), UV-vis diffuse reflectance spectra (DRS), field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), nitrogen adsorption-desorption, transient photocurrent response and photoluminescence (PL) spectra were employed to determine the properties of the samples. It is found that BiVO₄ nanosheets could pave well on the surface of graphene sheets. BiVO₄ nanosheets-GR composites with a proper addition amount of GR exhibited higher photocatalytic activity than bare BiVO₄ nanosheets toward liquid-phase degradation of rhodamine B (RhB) and methyl orange (MO) under visible light irradiation. The enhancement of photocatalytic activities of BiVO₄ nanosheets-GR composites can be attributed to the effective separation of photoexcited electron-hole pairs. This work not only provides a simple strategy for fabricating specific 2-D semiconductor-2-D GR composites, but also opens a new window of such 2-D semiconductor-2-D GR composites as visible light photocatalysts toward an improved visible light photoactivity in purifying polluted water resources.     

Hydrothermal Synthesis and Characterization of Visible-Light-Driven Dumbbell-Like BiVO4 and Ag/BiVO4 Photocatalysts

Visible-light-driven dumbbell-like BiVO₄ and Ag/BiVO₄ photocatalysts has been successfully synthesized by a simple hydrothermal method at 180 °C for 24 h. The as-synthesized photocatalysts were characterized by X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and UV–Vis absorption spectroscopy. The results obtained showed that ethylenediamine, citric acid, pH and hydrothermal reaction temperature have pronounced effects on the morphology of BiVO₄. Transmission electron microscopy observation shows that the Ag nanoparticles are homogenously dispersed on the surface of the BiVO₄ nanorods. Photocatalytic activities of the dumbbell-like BiVO₄ and Ag-loaded BiVO₄ photocatalysts were also evaluated by using methylene blue as a representative dye indicator under visible light irradiation. It is found that the photocatalytic performance of the as-synthesized BiVO₄ is obviously improved with the incorporation of the Ag nanoparticles. Mechanism for the enhancement of the photocatalytic activity of the Ag/BiVO₄ photocatalyst is also discussed.