室温铁磁性Ni2+掺杂TiO2纳米带的制备与表征

通过水热离子交换方法, 制得不同含量的过渡金属离子Ni2+掺杂的、锐钛矿型的TiO2纳米带. 使用X射线衍射(XRD), 扫描电子显微镜(SEM), 透射电子显微镜(TEM), 高分辨透射电子显微镜(HRTEM), X射线光电子能谱(XPS), 傅立叶变换红外(FTIR)光谱和磁性测试等手段对样品进行了详尽的表征. 结果表明, 经过离子交换, Ni2+离子进入到了TiO2纳米带的晶格中, 其中并没有形成金属Ni团簇或纳米颗粒. 此外, 磁性测试的结果表明, 实验制备的Ni-TiO2样品具有室温铁磁性和磁滞回线特性, 并且, 由于TiO2纳米带中Ni2+离子有较好的分散性, 在相同的外磁场条件下, 样品的磁化强度随着掺杂Ni2+含量的增加而增大.     

TiO2纳米线的制备及其光电性能研究

利用在钛箔表面沉积一层TiO₂纳米粒子作为晶种，与NaOH反应，制备了一维物质TiO₂纳米线。并用XRD、SEM、TEM、HRTEM及EDS等分析手段对TiO₂纳米线的成分、形貌、结构进行表征。结果表明，采用该方法制得的TiO₂纳米线直径在20～50 nm左右、长度可达几微米。反应温度能显著影响所得纳米线的形貌。研究了TiO₂纳米线的光电化学性能。随反应温度的升高TiO₂纳米线光电转换效率增大。     

太阳光活性的ZnTiO3 /TiO2纳米复合催化材料的制备及其表征

通过溶胶-凝胶(Sol-Gel)法制备了ZnTiO3/TiO2纳米复合光催化剂,利用透射电子显微镜(TEM)、X射线衍射(XRD)、紫外-可见光谱(UV-Vis)、红外光谱(FTIR)和ζ电位等技术进行了表征。以亚甲基蓝(MB)的降解为模型反应,考察了煅烧条件对复合材料光催化性能的影响。结果表明:600℃下焙烧3 h时所得样品具有最佳的光催化效果。如太阳光下7 h可使MB溶液的脱色降解率达92.9%,而TiO2的催化脱色率仅为68.9%;该催化剂还具有良好的稳定性能,重复使用5次后仍能保持MB溶液的脱色降解率在80%以上,且该催化剂易于离心分离去除。样品的结构缺陷-氧空位和TiO2-ZnTiO3相结与其催化性能有密切关系。     

N 掺杂TiO2光催化剂的制备及其可见光活性研究

A visible-light-active photocatalyst was prepared by calcination of the hydrolysis product of tetrabutyl titanate with ammonia as precipitant. The photocatalyst was characterized by X-ray diffraction (XRD), UV-Vis diffuse reflection spectra (DRS), thermal gravimetric-differential thermal analysis (TG-DTA), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM). The color of the photocatalyst was yellow and could absorb light wavelength under 550 nm as measured by DRS. The catalyst calcined at higher temperature will give lower absorbance for visible light. Structures of the sample were characterized mainly to be anatase by XRD except for the sample calcined at 700 ℃ which gave mixtures of anatase and rutile. TG-DTA results showed that temperature for anatase formation was 415 ℃. XPS results showed that doped-nitrogen was presented in the sample, they are important to show visible-light absorbency. The photocatalytic activities were evaluated using methyl orange and phenol as model pollutants, the results showed that over 90% of phenol could be degraded under visible light using N/TiO₂ as the catalyst after 4 hours reaction. Almost the same activity was found for the TiO₂ photocatalyst calcined at different temperature under sunlight but activities were different when the treatment was under UV light.     

TiO2-CoFe2O4磁性复合材料制备及太阳光催化性能

以四氯化钛、三价铁盐和二价钴盐为前驱体,采用超声波技术一步合成了TiO2-CoFe2O4新型复合光催化剂,运用VSM、XRD、TEM和UV-Vis技术进行了表征,以甲基橙为模拟污染物在太阳光照射下研究其光催化活性。结果表明:所制得的样品具有良好的顺磁性,其饱和磁化强度为212 Gs;样品中TiO2和CoFe2O4分别以锐钛矿相和尖晶石结构存在,粒径尺寸在40～50 nm之间;样品在紫外-可见区有很强的吸收。光催化结果表明复合催化剂具有较高的太阳光催化活性,循环使用3次,仍能保持良好的催化活性。     

静电自组装制备纳米TiO2/SiO2光催化材料

采用静电自组装方法制备了纳米TiO2/SiO2光催化材料。采用巯丙基三甲氧基硅烷偶联剂对SiO2进行干法改性,采用双氧水/冰醋酸将偶联剂巯基基团氧化为磺酸基基团。在正负电荷的吸引下,带负电荷的SiO2与带正电荷的钛聚合阳离子自发地组装在一起,经一定温度热处理得到纳米TiO2/SiO2光催化材料。采用XRD、FTIR、PL、UV-Vis DRS、SEM和ICP等对材料进行了分析和表征。采用甲基橙溶液评价材料的光催化性能。结果表明:SiO2促使锐钛矿的形成,抑制锐钛矿向金红石的转变,减小TiO2的晶粒尺寸,使得TiO2光吸收波长发生蓝移。TiO2与SiO2通过Si-O-Ti键发生结合。采用静电自组装方法制备的材料中TiO2的含量高于传统方法,导致材料的光催化性能有所提高。     

双介孔结构的纳米TiO2/I2复合材料的制备及其可见光催化性能

以钛酸丁酯为前驱体, 碘溶胶为碘源, 在室温下采用水解沉淀法制备了单质碘和纳米TiO₂复合的双介孔结构光催化剂(M-I₂-TiO₂). 采用X射线衍射(XRD)、透射电子显微镜(TEM)、比表面分析(BET)、紫外-可见(UV-Vis)漫反射光谱和傅里叶变换-红外光谱(FT-IR)对M-I₂-TiO₂进行了表征. 以次甲基蓝(MB)溶液为模拟废水, 对M-I₂-TiO₂的光催化性能进行了评价, 研究了不同热处理温度对光催化活性的影响. 结果表明, M-I₂-TiO₂在可见光区有显著的吸收, 300 ℃热处理得到的样品比表面积高达227.6 m²/g, 600 ℃热处理所得样品的比表面积仍高达111.8 m²/g, 而400 ℃热处理所得样品具有最好的光催化降解性能. 双介孔结构纳米TiO₂/I₂复合材料的光催化降解性能显著高于相同方法制备的纯TiO₂和Degussa P-25商业产品. 催化剂经6次重复使用其光催化活性基本保持不变.     

磁载光催化剂TiO2/SiO2/Ni0.5Fe2.5O4的制备及其催化氧化性能

采用固相反应法制备磁载体(SiO₂/Ni_0.5Fe_2.5O₄),溶胶-凝胶法得到易于磁分离回收的磁载光催化剂TiO₂/SiO₂/Ni_0.5Fe_2.5O₄。用XRD、SEM、IR和UV-Vis等进行表征。研究了太阳光下催化剂对亚甲基蓝溶液的脱色性能。结果表明,在太阳光下,磁载光催化剂TiO₂/SiO₂/Ni_0.5Fe_2.5O₄可使亚甲基蓝溶液迅速脱色；3次循环使用后脱色率仍为95%以上,回收率为98.8%。     

蛭石负载TiO2光催化剂的制备与性能

以新疆尉犁工业蛭石为载体,采用溶胶-凝胶法制备负载型二氧化钛光催化剂,利用XRD、TG、SEM、IR和低温N₂吸附－脱附对负载型二氧化钛进行表征,并以亚甲基蓝为目标降解物对其光催化性能进行研究。讨论了不同TiO₂负载量、反应温度和煅烧温度等因素对负载型二氧化钛光催化性能的影响,结果表明：TiO₂负载量为4.0wt%,反应温度为40 ℃,煅烧温度为400 ℃时,复合材料光催化效果最好,经60 W紫外灯照射20 min后,TiO₂/VMT复合材料对亚甲基蓝溶液的降解率为92.08%。     

Preparation and photocatalytic degradability of TiO2/polyacrylamide composite

Based on the unique absorbent characters and three-dimensional network structure of polyacrylamide (PAM) superabsorbent polymer, a photocatalytic degradable TiO₂/PAM composite was synthesized by an aqueous solution polymerization method with N,N′-methylene bisacrylamide as crosslinker, potassium peroxydisulfate as initiator, acrylamide as monomer, and TiO₂ (P-25) as functional filler. The photocatalytic degradability of the composite was evaluated using methyl orange as photodegradation target, and the recovery and reproducibility of the composite was investigated. It was found that TiO₂/PAM composite had a good photocatalytic degradability, the composite also possessed a good reproducibility of photocatalytic degradability, which is possible to be used in practical process.     

SiO2负载氮掺杂TiO2可见光响应光催化剂的制备及性能

以四氯化钛为钛源,尿素为氮源,采用液相水解-沉淀法制得SiO2负载N掺杂TiO2可见光响应TiO2-xNy/SiO2光催化剂(TSN)。以苯酚为模型物,考察了TSN在可见光区、紫外光区及太阳光下的光催化活性,以及催化剂的使用寿命、分离性能。采用XPS、FTIR、UV-Vis DRS、XRD、TEM和低温氮物理吸附等对催化剂的结构进行表征。结果表明,N以阴离子形式进入TiO2体相并置换晶格中的O,适量N掺杂的TSN在紫外光区、可见光区及太阳光下均表现出较高的活性。SiO2与TiO2界面间有Ti-O-Si键形成,结合牢固。N掺杂在TiO2表面生成Ti-O-N键,形成新的能级结构,使催化剂的吸收红移至450~500 nm,诱发TiO2可见光催化活性。SiO2负载可减小TiO2颗粒平均尺寸,增加催化剂比表面积;同时SiO2负载还可改善催化剂的分离性能,提高催化剂使用寿命。     

Cu掺杂TiO2及其纳米管的制备、表征与光催化性能

通过溶胶-凝胶法和水热法制备了Cu掺杂TiO₂纳米粉末及其纳米管,并通过XRD、TEM、FE-SEM、EDS、UV-Vis/DRS等手段分析了样品的结构。发现以Cu掺杂TiO₂纳米粉末为水热反应原料制备的纳米管中不含Cu,对其原因进行了分析讨论并通过Zn掺杂TiO₂纳米粉末证实：以金属掺杂TiO₂纳米粉末为原料,通过水热法制备TiO₂纳米管中不含有相应金属离子,这是由于金属离子在强碱水热条件下形成金属配离子,使金属离子溶解于水中而不能形成金属掺杂TiO₂纳米管。对所得样品进行了光催化性能测试,发现：Cu掺杂TiO₂粉末的光催化产氢效率为0.75 μmol·(g·h)^-1,高于由其本身及P25通过水热法制备的TiO₂纳米管(分别为：0.42 μmol·(g·h)^-1,0.25 μmol·(g·h)^-1)的光催化产氢效率。     

等离子体修饰磁载TiO2光催化剂性能研究

以化学共沉法制备的CoFe₂O₄纳米粒子为磁核,采用TiCl₄水解包覆技术制备磁载二氧化钛纳米复合粒子CoFe₂O₄ /TiO_x(TCF),利用低温等离子体技术修饰TCF制备了CoFe₂O₄/TiO₂(PTCF)纳米复合光催化剂。运用VSM(振动样品磁强计)技术对样品磁性能进行研究,结果表明：等离子体修饰后的复合材料仍具有较高的饱和磁化强度,可在外加磁场作用下实现催化剂在水中的分离与回收;样品的XRD、TEM和UV-Vis分析测试结果表明：等离子体修饰后的复合材料有锐钛矿型TiO₂存在;TEM谱图显示磁核CoFe₂O₄的平均粒径约为20 nm,TCF复合粒子的粒径约为30~40 nm,TiO₂包覆层的厚度为10~20 nm。与纯TiO₂相比PTCF样品对光的吸收拓展到整个紫外-可见区,扩大了光谱响应范围;对甲基橙溶液降解的光催化活性评价研究表明：TCF复合粒子等离子体修饰后的PTCF纳米复合光催剂的光催化活性明显提高。     

The release of TiO2 and SiO2 nanoparticles from nanocomposites

There is a growing interest in the development of nanocomposites consisting of organic polymers and TiO₂ or amorphous SiO₂ nanoparticles. These nanoparticles may be released from nanocomposites. There is evidence that amorphous SiO₂ and TiO₂ nanoparticles can be hazardous. Thus, in the design of nanocomposites with such nanoparticles, hazard reduction extending to the full nanocomposite life cycle would seem a matter to consider. Options for hazard reduction include: changes of nanoparticle surface, structure or composition, better fixation of nanoparticles in nanocomposites, including persistent suppression of oxidative damage to polymers by nanoparticles, and design changes leading to the release of relatively large particles.     

正钛酸胶溶法制纳米TiO2薄膜及性能表征

The Nanometer TiO₂ thin film was prepared by sol method with titanic acid precursor from industrial TiOSO₄ solution. The characters of the sol and the factors affecting sol formation were investigated by ζ electricity potential. The crystalline structure, particle size, appearance shape and photo-catalytic activity were characterized by XRD, SEM, TEM and spectrophotometer. The study show: (1) pH value and HNO₃concentration effected importantly on the forming process and stability of the sol. The thermodynamic condition for forming sol is pH=0.5～1.5. The lower the HNO₃concentration,the more stable the sol. The ζ electricity potential of the sol, with 5% HNO₃as gluing reagent, was up to 48 mV, and shelf life of the sol could more than 10 months. (2) The film, made from the sol and crystallized at 400 ℃, had the characters of anatase structure and crystal size of 18.5 nm by XRD analysis. The SEM imagines show that TiO₂ film was with the characteristics of tight surface structure, The TEM imagine showed the mean particle size is about 20 nm. The photo-degrading test data indicate that the photo-degrading rate to methyl orange solution of 20 mg·L^-1 was more than 84% in 5 hours.     

Visible-light responsive dye-modified TiO2 photocatalyst

A series of dye-modified TiO₂ photocatalysts were synthesized using dye Chrysoidine G (CG), tolylene-2,4-diisocyanate (TDI), and commercial TiO₂ (Degussa P25) as starting materials. TDI was used as a bridging molecule whose two -NCO groups reacted with Ti-OH of TiO₂ and -NH₂ groups of CG, respectively. As a result, special organic complexes were formed on the TiO₂ surface via stable π-conjugated chemical bonds between TiO₂ and dye molecules, confirmed by FT-IR, XPS, and UV-vis spectra. Due to the existence of π-conjugated surface organic complexes, the as-synthesized photocatalysts showed a great improvement in visible absorption (400-550 nm). Methylene blue, as a photodegradation target, was used to evaluate the photocatalytic performance, and the dye-modified TiO₂ exhibited much better activity under the visible light irradiation than bare TiO₂.     

Preparation, characterization, and infrared emissivity property of optically active polyurethane/TiO2/SiO2 multilayered microspheres

Optically active polyurethane/titania/silica (LPU/TiO₂/SiO₂) multilayered core–shell composite microspheres were prepared by the combination of titania deposition on the surface of silica spheres and subsequent polymer grafting. LPU/TiO₂/SiO₂ was characterized by FT-IR, UV–vis spectroscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TGA), SEM and TEM, and the infrared emissivity value (8–14 μm) was investigated in addition. The results indicated that titania and polyurethane had been successfully coated onto the surfaces of silica microspheres. LPU/TiO₂/SiO₂ exhibited clearly multilayered core–shell construction. The infrared emissivity values reduced along with the increase of covering layers thus proved that the interfacial interactions had direct influence on the infrared emissivity. Besides, LPU/TiO₂/SiO₂ multilayered microspheres based on the optically active polyurethane took advantages of the orderly secondary structure and strengthened interfacial synergistic actions. Consequently, it possessed the lowest infrared emissivity value.     

二氧化钛纳米管阵列的制备、改性及应用

二氧化钛因其在光催化、染料敏化太阳电池、生物医药等应用领域表现出优异性能而成为材料科学领域重点研究的化合物之一。本文介绍了近年来阳极氧化法制备不同形貌的TiO2纳米管(TiO2NTs)阵列,探讨了电解液、阳极氧化时间、电压三个因素对TiO2纳米管形貌的影响,综述了掺杂、复合、表面修饰这三种能对TiO2纳米管进行化学或物理修饰的改性手段以及改性后的TiO2纳米管阵列在光催化、太阳能电池、生物医学、传感等领域的应用研究进展。最后,指出国内外针对二氧化钛纳米管阵列研究现状所存在的问题,并对今后的研究工作提出了展望。     

Pt / InVO4 / TiO2可见光催化剂的制备及性能研究

采用溶胶-凝胶法制备了Pt / InVO₄ / TiO₂三元体系可见光催化剂。以乙烯为模拟目标分子，评价其光催化活性并与二元体系催化剂Pt / TiO₂ 和InVO₄ / TiO₂进行比较。用DRS，XRD对催化剂的吸收带边和晶型进行了表征。结果表明：Pt / InVO₄ / TiO₂在可见光区（λ>450 nm）的光催化比活性比Pt / TiO相似文献   

Synthesis and Characterization of TiO2/YFeO3 and Its Photocatalytic Oxidation of Gaseous Benzene

YFeO₃ was prepared by coprecipitation method and citric acid method, and TiO₂/YFeO₃ heterosystem photocatalysts were synthesized by loading TiO₂ sol on the surface of YFeO₃via sol-gel method. Their photocatalytic activities were evaluated by the decomposition of gaseous benzene under UV light illumination. The prepared photocatalysts were characterized by nitrogen adsorption-desorption, X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and UV-Vis diffuse reflectance spectroscopy. Results revealed that the heterosystem photocatalysts prepared by coprecipitation method showed higher activity, and the maximum conversion of benzene could reach 44.7% within 180 min. The YFeO₃ samples prepared from coprecipitation method and citric acid method were absolutely in orthorhombic phase. The deposited titania was dispersed on the surface of carrier and a certain interaction existed between TiO₂ and YFeO₃. The two heterosystems photocatalysts had narrow band-gap energies.