Comparison of the time-temperature superposition of the relaxation modulus and time-to-break of preswollen gels

This paper describes the work carried out to investigate the pore pressures occurring in secondary consolidation. A theoretical approach and an experimental technique was developed in order to conduct the study. By considering compression to occur only due to water leaving the soil it was possible to derive an expression for the dissipation of pore pressure in the secondary phase. By further simplified assumptions which are based on experimental observations, the above general solution was reduced to a simple formula which predicted the observed behaviour of pore water pressures during secondary consolidation.     

Rheology on the drawing zone in glass spinning

This paper describes the work carried out to investigate the pore pressures occurring in secondary consolidation. A theoretical approach and an experimental technique was developed in order to conduct the study. By considering compression to occur only due to water leaving the soil it was possible to derive an expression for the dissipation of pore pressure in the secondary phase. By further simplified assumptions which are based on experimental observations, the above general solution was reduced to a simple formula which predicted the observed behaviour of pore water pressures during secondary consolidation.     

Nonlinear motion equations for a non-Newtonian incompressible fluid in an orthogonal coordinate system

This paper describes the work carried out to investigate the pore pressures occurring in secondary consolidation. A theoretical approach and an experimental technique was developed in order to conduct the study. By considering compression to occur only due to water leaving the soil it was possible to derive an expression for the dissipation of pore pressure in the secondary phase. By further simplified assumptions which are based on experimental observations, the above general solution was reduced to a simple formula which predicted the observed behaviour of pore water pressures during secondary consolidation.     

Rhéologie particulière des solutions de polymères en millieus poreux

This paper describes the work carried out to investigate the pore pressures occurring in secondary consolidation. A theoretical approach and an experimental technique was developed in order to conduct the study. By considering compression to occur only due to water leaving the soil it was possible to derive an expression for the dissipation of pore pressure in the secondary phase. By further simplified assumptions which are based on experimental observations, the above general solution was reduced to a simple formula which predicted the observed behaviour of pore water pressures during secondary consolidation.     

An extension of Reiner’s “Deborah Number” concept to a wide field of rheological investigations

This paper describes the work carried out to investigate the pore pressures occurring in secondary consolidation. A theoretical approach and an experimental technique was developed in order to conduct the study. By considering compression to occur only due to water leaving the soil it was possible to derive an expression for the dissipation of pore pressure in the secondary phase. By further simplified assumptions which are based on experimental observations, the above general solution was reduced to a simple formula which predicted the observed behaviour of pore water pressures during secondary consolidation.     

考虑桩体内径向渗流的复合地基固结解

考虑了桩体内径竖向组合渗流和涂抹区土体水平渗透系数的两种变化模式,得到了此类固结问题的控制方程.采用新的初始条件,得到了控制方程的解答,给出了桩周土体和桩体内的平均孔压.在此基础上,把桩体的固结压缩引人对复合地基总平均固结度的定义中,分别给出了复合地基按应力和按应变定义的总平均固结度.结果表明:按应力和按应变定义的复合地基的总平均固结度相等;考虑桩体内径向渗流比不考虑桩体内径向渗流的复合地基固结度要小,而且随着桩间距的增大,两者之间的差值逐渐减小;考虑涂抹区水平渗透系数逐渐变化比假定涂抹区水平渗透系数保持不变的复合地基的总平均固结度大.     

渗透固结试验装置的改进

针对传统固结仪不能进行渗透试验的不足,对固结仪进行了改装。改装后的固结仪不仅可以交叉进行固结、渗透试验,以研究不同荷载作用下土样的渗透特性,而且可以通过三通阀控制排水条件,进行双面排水固结试验,或在单面排水条件下量测固结过程中试样不排水面处的孔隙水压力,也可通过串联固结仪分别研究试样不同截面处孔隙水压力的消散规律。新仪器具有构造简单,密封性能好的特点。通过与常规固结、渗透试验的结果对比,验证了采用改装固结仪测定固结模型参数的可靠性。另外,通过单面排水固结试验发现了孔压滞后现象。     

正常固结饱和黏性土三剪有限变形弹塑性本构模型研究

基于三剪统一强度准则,利用等量代换法和坐标平移法分别推导出正常固结饱和黏性土的三剪破坏应力比,并将其与修正剑桥模型相结合,得到三剪统一屈服面方程。为反映饱和黏性土的变形非线性及大变形特性,基于有限变形理论,建立了正常固结饱和黏性土的三剪统一有限变形等量代换法和坐标平移法2种弹塑性本构模型。为验证模型的适用性,取江西红黏土制备三种不同压实度的试样,在不同围压下进行常规三轴固结不排水和固结排水压缩试验。将试验数据与本文所提2种有限变形模型及相应的2种小变形模型计算结果进行了对比分析,结果表明,随着变形的发展,有限变形模型相对于小变形模型更接近试验结果,能较好地反映黏性土因高孔隙率（低初始压实度、小围压及压缩变形前期）而产生的大变形特性,虽然小变形模型的计算偏差会随着土样初始压实度和所施加围压的增大而减小,但有限变形模型对不同压实度和围压的计算偏差均相对较小,其中,等量代换法有限变形模型在初始压实度较大或者围压较高时所得计算偏差相对最小。对所提本构模型所做真三轴分析表明,中间主应力影响系数b和初始压实度对土体的强度和变形特性具有一定的影响。主应力差、孔隙水压力和体应变与b值呈正相关性,主应力差与初始压实度呈正相关性,孔隙水压力和体应变与初始压实度呈负相关性。     

Pore Water Pressure Distribution and Dissipation During Thaw Consolidation

A novel apparatus was developed for measurement of pore water pressure distribution and dissipation during thaw consolidation. Thaw consolidation tests were conducted to verify the applicability of nonlinear stress–strain relationship in 3-D large strain thaw consolidation theory. During thawing process, the measured pore pressure at different layers of soil samples increased sharply at first; when a certain value was approached, it stepped into dissipation stage. It was proved that the calculated results have a good agreement with tested results on both pore pressure distribution and dissipation. Further analysis indicated that nonlinearity of pore pressure distribution was proportionally related to thaw consolidation ratio (R), while it was opposite for thaw consolidation degree.     

温度梯度水分扩散系数对非饱和双重孔隙岩体中THM耦合影响的有限元分析

建立了一种饱和–非饱和遍有节理岩体的双重孔隙—裂隙介质热—水—应力耦合模型,并研制出相应的二维有限元程序。通过一个假定的位于非饱和双重孔隙—裂隙岩体中的高放废物地质处置库算例,就温度梯度水分扩散系数不同的三种工况,考察了岩体中的温度、孔隙水压力、饱和度、地下水流速和主应力的变化、分布情况。结果显示：各工况计算域中温度场及应力场基本相同, 当岩体温度梯度水分扩散系数较大时,近场的负孔隙水压力上升到很高的数值,负裂隙水压力有所下降,饱和度亦有相应的变化,当温度梯度水分扩散系数小到一定程度后,其影响也将逐渐消失。     

真空预压法加固吹填土的孔隙水压力试验研究

利用真空预压法处理吹填土时,孔隙水压力变化常常反映土体固结程度的好坏。通过6个模型箱试验,监测不同排水系统下孔隙水压力变化,确定有效排水体间距。研究发现0.4m间距的土内孔压下降效果比0.8m间距的土内孔压下降效果好; 排水体内的孔隙水压力与排水体类型有关,且距离排水体10cm处土体内的孔隙水压力仅为排水体内孔隙水压力的1/2弱; 滤膜排水系统中的吹填土孔隙水压力下降幅度最快,B型排水板系统次之,而砂井系统最慢。另外,对于吹填土而言,排水体有效间距介于0.4m与0.8m之间,其中滤膜的有效间距最大,B型排水板次之,砂井远小于前两者。     

Thermal Responses of Saturated Silty Clay During Repeated Heating–Cooling Processes

The thermal responses of the saturated silty clay to repeated heating–cooling are studied in laboratory. Results show that the pore pressure induced by undrained heating increases with increasing temperature, but the peak pore pressure appears a degradation trend with increasing temperature cycles. During the consolidation process at an elevated temperature, the specimen contracts due to the dissipation of the pore pressure; however, the thermally induced pore pressure is under no conditions fully dissipated to zero, therefore, there always exists a residual pore pressure in the specimens once a thermal loading higher than the ambient temperature is applied. During the undrained cooling, pore pressure continues to decline and eventually falls below zero. During the isothermal consolidation at the original temperature, the specimen begins to expand due to water absorption caused by the negative pore pressure, and eventually reaches a steady value. In addition, the consolidation volumetric strain generated during the drainage process at 50°C is greater than that during the water absorption process at 25°C, the difference seems to be most obvious for the first three cycles, and begins to diminish gradually thereafter.     

软粘土深基坑开挖时间效应的有限元分析

目前对开挖工程一般只作总应力法分析,本文将Ｂｉｏｔ固结有限元用法饱和软粘土地基深基坑性状的研究,通过典型算例分析土体超散负孔压的分布及分步开挖工程的固结效应,阐述了开挖速率的影响。最后对某深开挖工程实例进行了分析,旨在为基坑工程的设计和施工提供参考。     

岩土介质非稳态热固结耦合问题的热源函数法

考虑耦合效应的饱和土体热固结问题控制方程,利用Fourier变换、Laplace变换给出其在变换域上的解,将初始温度场分布视为虚拟的热源或者将热源等价为特定的初始温度分布,利用热源函数法给出瞬时线热源非稳态温度场、应力场和位移场的解析求解方法,通过在时间域和空间域上进行积分,给出有初始温度场分布以及有分布内热源存在且热源强度随时间变化条件下的热固结问题计算方法。对一无限大物体内存在有平面矩形域热源情况下周围介质的温度、孔隙水压力以及位移等的变化特征进行分析。研究表明,热源函数法可有效地求解一系列复杂情况下的热固结问题。     

A new method for solving Biot＇s consolidation of a finite soil layer in the cylindrical coordinate system

A new method is developed to solve Biot＇s consolidation of a finite soil layer in the cylindrical coordinate system. Based on the governing equations of Biot＇s consolidation and the technique of Laplace transform, Fourier expansions and Hankel transform with respect to time t, coordinate θ and coordinate r, respectively, a relationship of displacements, stresses, excess pore water pressure and flux is established between the ground surface （z = 0） and an arbitrary depth z in the Laplace and Hankel transform domain. By referring to proper boundary conditions of the finite soil layer, the solutions for displacements, stresses, excess pore water pressure and flux of any point in the transform domain can be obtained. The actual solutions in the physical domain can be acquired by inverting the Laplace and the Hankel transforms.     

黄土固结蠕变特性试验研究

基于杨凌地区黄土的单向固结试验资料,分别研究了加载条件下原状黄土和扰动黄土的固结蠕变特性,由试验数据整理分析出不同含水率、不同固结压力下的固结蠕变曲线簇,根据蠕变曲线形态特征,推导出单向固结条件下黄土的应变-时间关系并拟合得到该关系中的参数,在分析参数与固结压力之间关系的基础上推导出黄土的一维固结蠕变本构关系,经试验证明,该关系能较好的描述杨凌地区黄土的固结蠕变特性。另外,基于试验资料以及Buisman次固结系数的概念,分析出次固结系数与固结压力之间的定量关系,为确定固结压力对黄土次固结特性的影响提供了一种新途径。     

Steady state responses of poroelastic half-space soil medium to a moving rectangular load

The dynamic steady state responses of a poroelastic half-space soil medium subjected to a moving rectangular load are investigated analytically/numerically. The full dynamic poroelastic theory of Biot is employed, under the assumption of an incompressible solid grain and neglecting the apparent mass density. Using the Fourier transform, the governing equations of motion are then reduced to a system of four coupled ordinary differential equations which are solved semi-analytically. Soil vertical displacements, accelerations and pore water pressures induced by moving load are calculated. Computed result shows that load velocity and intrinsic permeability of the soil medium shows an apparent effect on its dynamic responses and pore water pressures.     

BIOT’S CONSOLIDATION ANALYSIS FOR CYLINDRICAL SOIL-SAMPLE BASED ON HANSBO’S FLOW1)

诸多黏性土渗流试验表明,在低水力梯度下渗流会出现明显偏离Darcy定律的现象. 为了分析渗流的非Darcy特性对固结过程 的影响,引入Hansbo渗流方程描述圆柱土样内的渗流,重新推导轴对称条件下的Biot固结方程,并给出方程的Crank--Nicolson有限 差分格式. 通过与Darcy渗流条件下轴对称Biot固结方程解析解的对比,验证计算方法的有效性. 然后分析Hansbo模型参数对圆柱 土样固结过程的影响. 计算结果表明：与Darcy渗流相比,Hansbo渗流会延缓圆柱土样的固结过程. 随着Hansbo渗流参数m或I¹的增大,在固结前期,Mandel--Cryer效应会更加显著,即孔隙水压力峰值将提高,且达到该峰值的时间 会延迟;在固结中后期,孔压消散滞后的现象也更加明显. 不过,Hansbo渗流对位移的影响很小.     

衰变热源作用下饱和多孔介质热固结问题的扩展精细积分法

热源作用下饱和多孔介质热固结效应是土木及能源工程领域的一个重要课题.由于问题的复杂性,已有的研究大多将介质假定为均匀各向同性,且将热源假定为恒定强度.实际工程中,天然饱和多孔介质常表现出明显的分层特性,热源强度也存在衰变性,为此本工作采用扩展精细积分法对衰变热源作用下层状饱和多孔介质的热固结问题进行研究.借助于积分变换,将饱和多孔介质热固结问题的偏微分方程转化为变换域内的常微分方程;然后对饱和多孔介质微层元进行合并消元,并结合边界条件,推导出衰变热源作用下层状饱和多孔介质热固结问题在积分变换域内的扩展精细积分解;对所得解答进行相应的数值积分逆变换,可获得所求温度、超静孔压及竖向位移在物理域内的解答.基于上述求解过程,编制相应的计算程序进行数值计算,通过与已有文献对比,验证本文扩展精细积分法在求解层状饱和多孔介质热固结问题中的适应性和正确性;最后通过几组算例,分析热源衰变周期、热源埋深及介质的成层性对热固结效应的影响.结果表明:热源衰变周期对温度和超静孔压的峰值、以及达到峰值的时间均有明显影响,衰变周期越长,二者峰值均越大,且达到峰值所需时间越长;热源埋深对超静孔压及竖向位移变化影响显著,深埋热源作用时热源两侧竖向位移呈对称分布,而浅埋热源两侧则无此现象;饱和多孔介质的分层特性对热固结效应影响明显.     

A RHEOLOGICAL CONSOLIDATION MODEL FOR SOFT CLAY WITH CONSIDERATION OF TEMPERATURE AND THE ANALYTICAL

基于四元件流变模型,考虑温度影响,建立了宁波软黏土流变固结模型,并利用拉普拉斯变换得到瞬时加载条件下的考虑温度 影响的饱和软黏土流变固结解析解;利用不同温度下软黏土的流变固结试验结果,拟合获得了四元件流变模型参数,进行编程得到理论值, 并与试验值进行对比. 结果表明：该模型能较好反映宁波软黏土流变固结特性,计算结果与试验结果较为吻合.温度的升高导致渗透系数增大,在相同的时间内孔压消散 越快, 固结 越快.