氨丙基封端聚氰丙基甲基硅氧烷改性环氧树脂——两相相溶性及表界面形态研究

本文针对聚二甲基硅氧烷改性环氧树脂相溶性太差,性能不够理想等问题,提出用氰丙基替代部分甲基以减小聚硅氧烷与环氧树脂的溶度参数差,改善两相的相溶性。采用氨丙基封端的聚氰丙基甲基硅氧烷低聚体(表1)单独或与二乙烯三胺(固化剂)一同与双酚A环氧树脂反应,合成了一系列不同聚硅氧烷分子量和重量百分比的样品(表2)。并用示差扫描量热计(DSC)、动态力学谱(DMA)、光电子能谱(XPS)、接触角仪、扫描电子显微镜(SEM)、电子拉力试验机对其进行研究。结果表明在聚硅氧烷软段中引入氰丙基可提高两相的相溶性并使增韧效果明显改善。     

超亲水性韧性聚乳酸纤维毡的制备

通过高压静电纺丝制备了具有不同三醋酸甘油酯(GTA)含量的聚乳酸超细纤维毡,场发射扫描电子显微镜、示差扫描量热仪、水接触角和力学性能测试结果表明,随着GTA含量的增加,纤维之间趋于粘连,形成立体网状结构.纤维毡的断裂伸长率、回弹率、拉伸强度可分别达到200%、85%、4.24 MPa.当GTA质量分数高于50%时,水能迅速浸润纤维毡.     

累托石/聚丙烯插层纳米复合材料的制备与性能

采用熔融共混法制备了有机改性累托石 (OREC)粘土 均聚聚丙烯 (PP)纳米复合材料 ,以X 射线衍射分析 (XRD)及透射电子显微镜分析 (TEM)观察了复合材料的相貌结构 ,研究了复合材料的力学性能及热性能 .结果表明 ,OREC在添加份数较少时可与均聚聚丙烯熔融插层形成插层型聚丙烯纳米复合材料 ,该复合材料与纯PP相比 ,具有较高的拉伸强度、断裂伸长率及冲击强度 .在有机粘土添加 2 %时 ,复合材料的拉伸强度、断裂伸长率、冲击强度最高 ,与纯PP相比 ,2 %添加量的聚丙烯纳米复合材料拉伸强度提高 6 5 7% ,断裂伸长率提高 2 89 3% ,冲击强度提高 14 1% ,10 %失重率时对应的热分解温度提高 50K .     

多乙烯基硅油改性丙烯酸酯乳液的合成及性能

以自制阳离子型乳化剂H、多乙烯基硅油和丙烯酸类单体为主要原料,采用一步法和半连续种子乳液聚合法合成有机硅改性丙烯酸酯乳液。研究了不同聚合方法、不同有机硅含量对硅丙乳液乳胶膜的吸水率、疏水性能的影响,通过纳米粒度-Zeta电位分析仪、接触角仪、红外光谱、透射电镜对乳液及聚合物结构进行了表征。结果表明有机硅单体参与了聚合,乳液稳定性好、平均粒径小。采用半连续种子乳液聚合法合成乳液,有机硅最大添加量为40%(占壳层单体总量),乳胶膜的吸水率只有3.2%,对水的接触角达到105.2o。     

纳米纤维素晶须的表面改性及其在环氧树脂中的应用

以棉纤维素为原料,采用硫酸水解法制备了纳米纤维素晶须.以N,N-二甲基甲酰胺(DMF)为分散介质,二甲基氨基吡啶(DMAP)为催化剂,十二烯基琥珀酸酐为酯化剂对纳米纤维素晶须进行化学改性,得到了一系列取代程度不同的改性产物(记为DCNW).采用红外光谱(FTIR)、X射线衍射(XRD)、透射电子显微镜(TEM)和X射线光电子能谱(XPS)等手段对DCNW的结构和性能进行了分析和表征.选择表面取代度为0.3的改性产物作为复合材料的增强相.该改性产物能在丙酮中均匀分散和稳定悬浮,并且保持了改性前纳米纤维素晶须的棒状形态和高结晶度.将其分散于环氧单体中,通过浇铸法制备了纳米复合材料,考察了改性纳米纤维素晶须添加量对纳米复合材料拉伸性能、动态力学性能及耐湿热性的影响规律.结果表明,与空白环氧树脂相比,添加了改性纳米纤维素晶须的纳米复合材料的拉伸强度、杨氏模量和断裂伸长率都得到了提高.玻璃化转变温度、耐湿热性也得到了显著改善.其中,当改性纳米纤维素晶须的添加量为3.5%时,拉伸强度从纯环氧的39.85 MPa提高到72.33 MPa,增加了82%;杨氏模量增大了21%;断裂伸长率从纯环氧树脂的2.45%提高到7.29%,增加了198%;Tg值从纯环氧的103.4℃,提高到134.1℃;吸水率从1.9%下降到1.4%.     

有机硅-聚氨酯共聚乳液的制备和乳胶膜相结构及其性能研究

以端羟丙基聚二甲基硅氧烷(HP-PDMS)、异佛尔酮二异氰酸酯、2,2-二羟甲基丁酸等为主要原料,采用分步投料法和无皂相反转乳化工艺制得粒径约50 nm的有机硅-聚氨酯共聚乳液,并对有机硅-聚氨酯乳胶膜的相结构和性能进行了表征,考察了HP-PDMS用量对乳胶膜相结构和性能的影响.DSC测试结果显示,与聚醚型聚氨酯乳胶膜相比,有机硅-聚氨酯乳胶膜中存在明显的相分离结构.FTIR分析结果表明,有机硅-聚氨酯乳胶膜硬段之间存在较强的氢键,它促进了相分离结构的形成.从AFM相图上可以观察到有机硅-聚氨酯乳胶膜中存在明显的海岛型相分离结构,其中聚硅氧烷软段的无定形微区构成了岛状分散相.随着有机硅含量的增加,有机硅-聚氨酯乳胶膜的相分离程度增加,弹性模量降低,断裂伸长率和柔韧性显著升高.有机硅-聚氨酯乳胶膜的起始分解温度低于聚醚型聚氨酯乳胶膜,但其在高温阶段的稳定性明显优于后者;对乳胶膜接触角和吸水率的研究表明,有机硅-聚氨酯乳胶膜的耐水性远高于聚醚型聚氨酯乳胶膜.     

改性TiO2纳米粒子对聚丙烯抗紫外光老化及结晶性能的影响

用苯乙烯-丙烯酸丁酯乳液共聚物包覆纳米TiO2,制备出P(St-BA)/TiO2复合粒子.利用扫描电子显微镜、偏光显微镜、差示扫描量热分析法和力学性能测试,研究复合纳米粒子对聚丙烯(PP)的结晶行为、力学性能和抗紫外光老化性能的影响.结果表明,P(St-BA)/TiO2复合纳米粒子能使PP的球晶尺寸得到细化,更好地分散在基体树脂中.改性TiO2纳米粒子能有效提高PP的力学性能和抗紫外光老化性能,PP的断裂伸长率从89%提高到106%;缺口冲击强度从2.6 KJ/m2提高到了3.4KJ/m2.经紫外光老化500h后,断裂伸长率保持率为31%,PP仅为8%;老化后缺口冲击强度保持率为65%,PP为31%.     

邻苯二酚-四乙烯五胺改性超高分子量聚乙烯纤维

应用Cat-TEPA改性超高分子量聚乙烯(UHMWPE)纤维,在难黏附的纤维表面形成均匀涂层.采用透射电子显微镜(TEM)、红外光谱(FTIR)、X射线光电子能谱(XPS)、X射线衍射(XRD)、示差扫描量热(DSC)、热重分析(TGA)和静态接触角测试等手段对其结构和性能进行了表征,并通过单丝拔出实验研究改性前后纤维与环氧树脂之间的界面剪切强度(IFSS),探索了反应物配比、反应时间对表面性能的影响,并确定最佳改性条件.结果表明Cat-TEPA共沉积改性未影响纤维的结晶和热稳定性,改性后纤维表面浸润性得到改善,且适当增加反应时间和TEPA含量能够提高纤维和树脂之间的IFSS,当Cat-TEPA摩尔比为1:4,反应时间为24 h时效果最佳,与未改性纤维相比,界面剪切强度提升约44%.     

低聚端羟基聚硅氧烷接枝增韧酚醛树脂的制备及性能

由低聚羟基封端聚硅氧烷（HO-PDM）与甲醛和苯酚的接枝反应制备了增韧改性酚醛树脂,用FT-IR对改性酚醛树脂的结构进行表征,用电子万能试验机测试了改性前后酚醛树脂的力学性能,用热重分析仪测试改性酚醛树脂的热稳定性。 测得改性酚醛树脂的断裂伸长率、冲击强度、抗拉强度分别为2.8%、2.875 kJ/m2和23.2 MPa;树脂失重20%的温度为431.28 ℃,峰值温度为441.8 ℃,800 ℃的残重率为51.02%。     

ma-异氰酸酯改性app及其在lldpe中耐水性的评价

依次用密胺(MA)、2,4-甲苯二异氰酸酯(TDI)对聚磷酸铵(APP)进行改性,并分别应用于低密度线性聚乙烯(LLDPE)中。分别用APP在水中的溶解度变化,APP处理的LLDPE水浸后的极限氧指数(LOI)变化和磷含量变化评价了APP的耐水性。结果发现,改性后的APP在水中的溶解度减小,未改性APP的溶解度是0.368 0,MA-TDI-APP是0.212 3,减小了42.3%。改性后APP处理的LLDPE水浸后的LOI变化量减小,添加量均为30%时,未改性APP处理的LLDPE的LOI值降低了5.3%,AM-TDI-APP处理的LLDPE的LOI值降低了2.5%。改性后APP处理的LLDPE水浸后磷含量损失降低,不同APP添加量的LLDPE,未改性APP处理的磷含量损失均在6.5%以上,MA-TDI-APP处理的磷含量损失在4%以下。用扫描电子显微镜观察了改性前后APP与LLDPE的相容性,改性后的APP与LLDPE的相容性较好,MA-TDI改性的APP与LLDPE的相容性最好。     

Study on damping properties of HVBR/EVM blends prepared by in situ polymerization

In comparison with normal damping rubbers such as natural rubber (NR), styrene butadiene rubber (SBR), isobutylene isoprene rubber (IIR) etc., Mo-based high vinyl polybutadiene rubber (HVBR) with high loss factor, excellent aging resistance and glass transition temperature closer to room temperature, is a promising damping material. The effective damping temperature range of HVBR could be further broadened by blending with ethylene-vinyl acetate (EVM) and the effects of blending methods (in situ polymerization blending or mechanical blending) and blending ratios on the damping properties and physical properties of HVBR/EVM blended rubber were studied. HVBR/EVM in situ polymerization blends was prepared by butadiene coordination polymerization by Mo-base catalyst in a toluene solution of EVM. The results of dynamic mechanical analysis (DMA) and scanning electron microscopy (SEM) of the blended vulcanizates via in situ polymerization blending revealed that the compatibility between HVBR and EVM was improved compared with that of the blended vulcanizates via the traditional mechanical blending method. The two phases of HVBR/EVM in situ polymerization blends had good dispersion and uniformity, the damping temperature range was significantly expanded, and the peak and valley of the damping temperature range were greatly improved. A blending ratio of HVBR/EVM900 = 100/40 showed the best damping properties and the effective damping temperature range (tanδ>0.3) was extended from −6.6 °C to 39.4 °C.     

Dichlorocarbene modified butadiene rubber (DCBR): Preparation,kinetic study,and its properties in natural rubber/DCBR blend vulcanizates

Dichlorocarbene modified butadiene rubber (DCBR) was prepared via the addition of the dichlorocarbene group in the presence of 2 phase transfer agents (cetyltrimethylammonium bromide and tetraethylammonium chloride). The effects of the reaction temperature and time, amount of dichlorocarbene precursor, and the type and amount of phase transfer agent on the chlorine content were investigated. The highest chlorine content (30%) in DCBR was obtained using 0.062 mol chloroform and 0.003 mol cetyltrimethylammonium bromide at room temperature for 19 hours although 27.9% was obtained after 12 hours. The kinetics of this dichlorocarbene modification was best described by the pseudo–first order rate law with 2 rate constants. For practical applications, the DCBR with chlorine contents of 10%, 20%, or 30% were blended with natural rubber (NR) and then vulcanized using the sulfur‐curing system. Although the polarity of DCBR was increased, a good compatibility between NR and DCBR still existed, resulting in improved mechanical properties. The oil resistance, flame retardant, and ozone resistance properties of the NR/DCBR blend vulcanizates were enhanced compared to those of a NR/butadiene rubber blend vulcanizate, which was related to the amount of chlorine incorporated into the DCBR.     

Preparation and mechanical properties of water-dispersible hyperbranched polymer grafted carbon black/natural rubber composites by latex blending method

In order to improve the mechanical properties of rubber-matrix composites, carboxyl-terminated hyperbranched poly (2-hydroxypropane-1,2,3-tricarboxylic acid) grafted carbon black (CB-g-CTHBP) was prepared, and it could be stably dispersed in water for up to 90 days. CB-g-CTHBP dispersion and natural rubber latex were blended to obtain NR/CB-g-CTHBP, and the effect of CB-g-CTHBP content on the mechanical properties of composites was discussed. The results show that the dispersibility and wettability of CB-g-CTHBP to composites are significantly improved after grafting hyperbranched polymer onto the surface. Compared with the composite filled with NR/CB, when the amount of filler is 30 phr, tensile strength, tear strength, and shore A hardness of NR/CB-g-CTHBP increase by 54.78%, 55.13%, and 20.96%, respectively. Moreover, CB-g-CTHBP could disperse more evenly in the natural rubber-matrix, and the interaction between CB-g-CTHBP and rubber-matrix could further enhance in the composite.     

In vitro drug release from silicone rubber–polyacrylamide composite

Composite materials containing drugs were prepared from silicone rubber and hydrogel. Cross linked polyacrylamide (PAAm) hydrogel particles were incorporated into a silicone rubber to enhance the hydrophilicity and drug release capacity of silicone rubber as a matrix. Progesterone and Thymol Blue were used as a hydrophobic and hydrophilic drug model, respectively. Different amounts of polyacrylamide (PAAm) were mixed with the drugs and uncured silicone rubber at room temperature. The composite matrices were formed using a compression molding press and cured by thermal and γ-irradiation curing methods. In vitro drug release behavior of composites and their physical and mechanical properties were investigated. The results indicated that the hydrophilic character of silicone rubber was more pronounced with increasing the amount of PAAm. Also, a significant effect on the drug release profiles was observed. The γ-irradiation curing method improved mechanical properties of composites and affected the drug release profiles. It was found that the amounts of released progesterone from γ-irradiated samples increased in comparison with the thermally cross linked composite since released Thymol Blue was reduced.     

微波处理和溶胶凝胶法共同改性废胶粉及其与天然橡胶复合材料性能的研究

采用微波处理打断废胶粉(WRP)的三维网状结构用来提高WRP在有机溶剂中的溶胀性,然后采用溶胶凝胶法,将微波改性后的WRP浸入正硅酸乙酯中,通过水解反应和缩合反应,在WRP表面原位生成SiO2网络,从而制得改性废胶粉(MWRP).将制得MWRP与天然橡胶(NR)共混,制备了NR/MWRP复合材料,研究了NR/MWRP复合材料的性能.通过热重分析仪、差示扫描量热仪和力学分析表明微波处理最佳时间是20 s.由于微波处理提高了NR与WRP的相容性,原位生成的SiO2粒子起到了补强作用,所以所制备的NR/MWRP复合材料拥有较好的力学性能;随着Si69的加入,抑制了SiO2粒子聚集,提高了SiO2粒子的分散性,从而进一步提高复合材料的力学性能并降低复合材料的Payne效应;在进行频率扫描时,硫化胶的储存模量随频率的增大而增大;硫化胶的温度扫描结果表明,随着温度的升高,复合材料中SiO2粒子聚集程度加剧并且复合材料出现老化的现象.为了提高复合材料的耐老化性能,N,N-间苯撑双马来酰亚胺(BMI)作为一种防老剂加入复合材料中,BMI利用Diels-Aider反应补偿橡胶在老化过程中所损失的交联键并提高NR与WRP的界面相容性,从而提高复合材料的耐老化性能.     

Studies on radiation grafting of methyl methacrylate onto natural rubber for improving modulus of latex film

Methyl methacrylate (MMA) can be grafted onto natural rubber (NR) in latex by gamma irradiation for improving the mechanical properties of the dry films. Physical blending of MMA-grafted NR latex with radiation vulcanized natural rubber latex (RVNRL) or simultaneous radiation grafting and crosslinking are found to be useful techniques for improving the properties of latex films. Moduli of the films are improved with increasing MMA content; however, tensile strength is reduced. High modulus without much reduction in tensile strength can be achieved if the MMA content is 50–60 parts per hundred rubber.     

Influence of Carbon Black and Silica Filler on the Rheological and Mechanical Properties of Natural Rubber Compound

Rubber compounds are reinforced with fillers such as carbon black and silica. In general, filled rubber compounds shows smooth rheological behavior and mechanical properties. Variation in rheological behavior and mechanical properties was studied in terms of the filler composition using natural rubber compounds filled with both carbon black and silica CB/Si = 0/60, 20/40, 30/30, 40/20 and 60/0 phr (parts per hundred rubber is parts of any non-rubbery material per hundred parts of raw gum elastomer (rubbery material)). The rheological behaviour can be showed in measurement of Mooney viscosity and cure time. The Mooney viscosity of rubber compounds increase with the increasing the carbon black in the compounds. The compound filled with CB/Si of 30/30 and 60/0 showed abnormal rheological behaviour in which the cure time decreased suddenly and the increased at certain ratio during the measurement. The mechanical properties such as hardness, abrasion resistance and tensile stress at 300% elongation were studied. In the hardness and abrasion resistance measurement, the higher ratio CB/Si decrease contribution of silica, which resulting smaller of hardness value. Ratio CB/Si 40/20 gives an optimum filler blended. It is also clearly understood that higher abrasion resistance mainly due to the lower hardness value under the same condition. The tensile stress at 300% elongation of rubber compound increased with the increasing carbon black filler.     

纳米ZnO对天然橡胶交联反应和热稳定性的影响

纳米氧化锌;纳米ZnO对天然橡胶交联反应和热稳定性的影响     

Blending of Natural Rubber/Recycled Ethylene-Propylene-diene Rubber: Promoting the Interfacial Adhesion Between Phases by Natural Rubber Latex

This article deals with blends based on natural rubber (NR) and recycled ethylene-propylene-diene rubber (R-EPDM). Natural rubber latex (NRL) was introduced into the blends to enhance interfacial adhesion between NR and R-EPDM. A new route of compounding was also suggested. The blends were prepared by mixing R-EPDM and other additives in NRL before blending with natural rubber on a two-roll mill. By applying this method, the homogeneity of the blends and cross-linking distribution are significantly improved. The blends exhibited superior state of cure, swelling resistance, mechanical properties and dynamic mechanical properties. The degree of entanglement between NR and R-EPDM also increased after NRL modification.     

Preparation and characterization of thermoplastic elastomer of poly(vinyl chloride) and chlorinated waste rubber

In order to develop applications for the abundant waste rubber powder, chlorinated waste rubber (Cl-WR) was prepared by a water based chlorination method using chlorine as chlorinating agent. In this paper, Cl-WR was used as an elastic filler and blended with poly(vinyl chloride) (PVC) matrix to develop a new thermoplastic elastomer PVC/Cl-WR. The mechanical properties, hydrophilicity, swelling resistance, morphology and thermal properties of PVC/Cl-WR were characterized and compared with those of PVC/waste rubber powder (PVC/WR) blends. The results indicated that the mechanical properties, hydrophilicity, swelling resistance and thermal properties of the PVC/Cl-WR blends showed noticeable improvements over PVC/WR blends due to the improved polarity of Cl-WR. Also, the excellent miscibility and compatibility of Cl-WR with PVC was demonstrated by scanning electron microscope (SEM) images of the resulting blends.