Sulfonated poly(arylene ether sulfone) ionomers containing fluorenyl groups for fuel cell applications

A series of sulfonated poly(arylene ether sulfone)s (SPEs) containing fluorenyl groups as bulky components were synthesized and characterized for fuel cell applications. Introduction of disodium 3,3′-disulfo-4,4′-difluorophenyl sulfone (SFPS) monomer gave ionomers with high acidity and accordingly high proton conductivity as well as high proton diffusion coefficient (D_σ) at low humidity. The membrane of SPE60 (where the number denotes mole percentage of the component containing sulfonic acid groups; IEC (ion exchange capacity) = 1.68 mequiv./g) exhibited high proton conductivity of 4.6 × 10⁻³ S/cm at 40% RH and 80 °C, which is one order of magnitude higher than that (6 × 10⁻⁴ S/cm) of our previous SPE (SPE-1, IEC = 1.58 mequiv./g). D_σ of SPE60 membrane was ca. 4 times higher than that of the SPE-1 membrane at low water volume fraction. SPE membranes showed good oxidative and hydrolytic stability as well as favorable thermal and mechanical properties. Small-angle X-ray scattering analyses showed that the phase separation of SPE membranes was much less developed than that of the perfluorinated Nafion membrane which accounts for lower hydrogen and oxygen permeability of the former membranes.     

New proton conducting hybrid membranes for HT-PEMFC systems based on polysiloxanes and SO3H-functionalized mesoporous Si-MCM-41 particles

For increased efficiency of high-temperature polymer electrolyte membrane fuel cells (HT-PEMFC), new types of membranes have to be developed. This approach has been realized by preparing hybrid membranes containing SO₃H-functionalized mesoporous Si-MCM-41 as hydrophilic inorganic modifier in a polysiloxane matrix exhibiting sulfonic acid groups and basic heterocyclic groups like benzimidazole. The proton conductivity of sulfonated particles was modelled on the atomic scale in order to understand the influence of the density of sulfonic acid groups and of the presence of water molecules. The different hybrid membranes are characterized concerning their thermal stability, water uptake, and proton conductivity. Whereas the proton conductivity of well-established, but expensive and at >120 °C not long-time stable Nafion membranes continuously decreases with increasing temperature, the polysiloxane membranes, which suffer from a low-proton conductivity at around 100 °C, recover at about 120 °C due to intrinsic proton transport. At 180 °C the pure polysiloxane shows a proton conductivity which is only one order of magnitude lower than that of Nafion. Moreover, if the polysiloxane membrane contains additionally 10 wt.% of an SO₃H-modified Si-MCM-41, the proton conductivity of such hybrid membrane at temperatures >180 °C and low relative humidity <10% is higher than that of Nafion membranes by a factor of 10.     

Heterogeneous ion-exchange membranes based on sulfonated poly(1,4-phenylene sulfide) and linear polyethylene: preparation, oxidation stability, methanol permeability and electrochemical properties

Poly(1,4-phenylene sulfide) was sulfonated with chlorosulfonic acid in 1,2-dichloroethane. The product (IEC = 2.38 mequiv./g) was ground and sieved (mesh size 63 μm) to obtain small particles. The particles and linear polyethylene were mixed in various ratios and the resulting blends were press-molded at 150 °C to obtain the membranes. Membranes containing up to 66 wt.% of sulfonated particles could be prepared without any problem in mechanical strength. The membranes were characterized by their stability in oxidative environment, ionic conductivity, and diffusive permeability to methanol. The membrane containing 66 wt.% of sulfonated particles was almost as conductive as Nafion 117; it exhibited, however, much lower diffusive permeability to methanol. In a strongly oxidative environment (3% aqueous H₂O₂ at 70 °C), the prepared membranes were less stable than Nafion 117, but much more stable than membranes with sulfonated poly(styrene-co-divinylbenzene) particles. In preliminary laboratory tests with H₂/O₂ and direct methanol fuel cells, the prepared membranes with high concentrations of sulfonated particles performed similarly to Nafion 117.     

Sulfonated poly(arylene thioether phosphine oxide)s copolymers for proton exchange membrane fuel cells

High molecular weight sulfonated poly(arylene thioether phosphine oxide)s (sPATPO) with various sulfonation degrees were prepared directly by aromatic nucleophilic polycondensation of 4,4′-thiobisbenzenethiol with sulfonated bis(4-fluorophenyl) phenyl phosphine oxide and bis(4-fluorophenyl) phenyl phosphine oxide. sPATPO in the acid form with sulfonation degrees of 60–100% exhibits a glass transition temperature higher than 230 °C and a 5% weight loss temperature above 400 °C, indicating high thermal stability. sPATPO with a high sulfonation degree shows high proton conductivity and good resistance to swelling as well. For instance, sPATPO-70 displays the conductivity of 0.0783 S/cm and a swelling ratio of 11.6% at 90 °C. TEM micrographs showed that sPATPO membranes with a high sulfonation degree could form continuous ion channels, which are favorable for improving the proton conductivity but harmful to remaining the mechanical property. The membranes are expected to show good performances in fuel cell applications.     

Supported carbon molecular sieve membranes based on a phenolic resin

The preparation of a composite carbon membrane for separation of gas mixtures is described. The membrane is formed by a thin microporous carbon layer (thickness, 2 μm) obtained by pyrolysis of a phenolic resin film supported over a macroporous carbon substrate (pore size, 1 μm; porosity, 30%). The microporous carbon layer exhibits molecular sieving properties and it allows the separation of gases depending on their molecular size. The micropore size was estimated to be around 4.2 Å. Single and mixed gas permeation experiments were performed at different temperatures between 25°C and 150°C, and pressures between 1 and 3.5 bar. The carbon membrane shows high selectivities for the separation of permanent gases like O₂/N₂ system (selectivity≈10 at 25°C). Gas mixtures like CO₂/N₂ and CO₂/CH₄ are successfully separated by means of prepared membranes. For example, the membrane prepared by carbonization at 700°C shows at 25°C the following separation factors: CO₂/N₂≈45 and CO₂/CH₄≈160.     

Sul-containing fluorinated polyimides for optical waveguide device

Novel sul-containing fluorinated polyimides have been synthesized by the reaction of 2,2′-bis-(trifluoromethyl)-4,4′-diaminodiphenyl sulfide (TFDAS) with 1,4-bis-(3,4-dicarboxyphenoxy)benzene dianhydride (HQDPA), 2,2′-bis-(3,4-dicarboxyphenyl)hexafluoropropane dianhydride (6FDA), 4,4′-oxydiphthalicanhydride (ODPA) or 3,4,3′,4′-biphenyl-tetracarboxylic acid dianhydride (s-BPDA). The fluorinated polyimides, prepared by a one-step polycondensation procedure, have good solubility in many solvents, such as N-methyl-2-pyrrolidinone (NMP), dimethylacetamide (DMAc), dimethyl sulfoxide (DMSO), cyclohexanone, tetrahydrofuran (THF) and m-cresol. The molecular weights (M_n's) and polydispersities (M_n/M_w's) of polyimides were in the range of 1.24 × 10⁵ to 3.21 × 10⁵ and 1.59–2.20, respectively. The polymers exhibit excellent thermal stabilities, with glass-transition temperatures (T_g) at 221–275 °C and the 5% weight-loss temperature are above 531 °C. After crosslinking, these polymers show higher thermal stability. The films of polymers have high optical transparency. The novel sul-containing fluorinated polyimides also have low absorption at both 1310 and 1550 nm wavelength windows. Rib-type optical waveguide device was fabricated using the fluorinated polyimides and the near-field mode pattern of the waveguide was demonstrated.     

Preparation and characterization of sulfated zirconia (SO4/ZrO2)/Nafion composite membranes for PEMFC operation at high temperature/low humidity

Fine particle superacidic sulfated zirconia (SO₄²⁻/ZrO₂, S-ZrO₂) was synthesized by ameliorated method, and composite membranes with different S-ZrO₂ contents were prepared by a recasting procedure from a suspension of S-ZrO₂ powder and Nafion solution. The physico-chemical properties of the membranes were studied by ion exchange capacity (IEC) and liquid water uptake measurements, scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis, thermogravimetry–mass spectrometry (TG–MS) and Fourier transform infrared (FT-IR) spectroscopy. The results showed that the IEC of composite membrane increased with the content of S-ZrO₂, S-ZrO₂ was compatible with the Nafion matrix, the incorporation of the S-ZrO₂ could increase the crystallinity and also improve the initial degradation temperature of the composite membrane. The performance of single cell was the best when the S-ZrO₂ content was 15 wt.%, and achieved 1.35 W/cm² at 80 °C and 0.99 W/cm² at 120 °C based on H₂/O₂ and at a pressure of 2 atm, the performance of the single cell with optimized S-ZrO₂ was far more than that of the Nafion at the same condition (e.g. 1.28 W/cm² at 80 °C, 0.75 W/cm² at 120 °C). The 15 wt.% S-ZrO₂/Nafion composite membrane showed lower fuel cell internal resistance than Nafion membranes at high temperature and low relative humidity (RH).     

Synthesis and characterization of P2O5–SiO2–X (X = phosphotungstic acid) glasses as electrolyte for low temperature H2/O2 fuel cell application

A new class of proton conducting glass membranes for hydrogen fuel cell applications are being developed using phosphotungstic acid. These glasses are being design to yield high proton conductivities could be potential substitutes for electrolytes in H₂/O₂ fuel cell. P₂O₅–SiO₂–PWA glasses have been non-crystalline phases confirmed by structural studies. The glass materials showed good mechanical and thermal stability, and also found a maximum proton conductivity of 9.1 × 10⁻² S/cm at 90 °C and 30% RH. The average pore size less than 5 nm was determined by Barrett–Joyner–Halenda (BJH) desorption method. The electrochemical activity was investigated by polarization curves and current–voltage profiles. A maximum power density value of 10.2 mW/cm² was obtained using 0.15 mg/cm² of Pt/C loaded on electrode and 5P₂O₅–87SiO₂–8PWA glasses at 30 °C and 30% humidity.     

Regioselective addition of protic acids to tricarbonyliron complexes of 2,3,5,6-tetrakis(methylene)-7-oxabicyclo[2.2.1]heptane. Crystal structure of (C10H10O)Fe2(CO)6

The main product of the thermal reaction between the title oxatetraene (I) and Fe₂(CO)₉ in ether/pentane is the bimetallic complex (C₁₀H₁₀O)Fe₂(CO)₆-diexo (II), which has C_2υ symmetry both in the solid state (X-ray analysis) and in solution. Whereas the protonation of the free ligand leads usually to polymerisation, the addition of a protic acid such as CF₃CO₂H to II proceeds cleanly at 0°C giving first a (η 3-allyl)Fe(CO)₃O₂CCF₃ complex (III). The intermediate III adds a second equivalent of acid in a slower step (k₂/k₁ = 0.1, CF₃CO₂D/CHCl₃, 0°C) giving the trans-bis(η³-allyl) isomer IV with high regioselectivity. The addition of CF₃CO₂D yields the corresponding deuteriomethylallyliron tricarbonyl trifluoroacetates III′ and IV′. No further deuterium incorporation is observed at 0°C, thus confirming the kinetic control of the regioselective double addition of protic acid to II.     

A new three-dimensional supramolecular network, [Cd(Hbic)2(H2O)]·(4,4′-bpy)·H2O (H2bic = 1-H-benzimidazole-5-carboxylic acid; 4,4′-bpy = 4,4′-bipyridine): Synthesis, crystal structure and luminescence property

A photoluminescent supramolecular compound [Cd(Hbic)₂(H₂O)]·(4,4′-bpy)·H₂O, H₂bic = 1-H-benzimidazole-5-carboxylic acid, has been synthesized and structurally characterized. With CH–π stacking and hydrogen bond, the 4,4′-bipyridine is used as template to construct the neighboring layers into a three-dimensional supramolecular architecture. Solid-state emission spectrum of compound 1 shows luminescence with emission peak at 565 nm.     

Resistance properties of a macroporous silica-based N,N,N′,N′-tetraoctyl-3-oxapentane-1,5-diamide-impregnated polymeric adsorption material against nitric acid, temperature and γ-irradiation

The resistance of a novel silica-based N,N,N′,N′-tetraoctyl-3-oxapentane-1,5-diamide (TODGA) polymeric adsorption material (TODGA/SiO₂-P) against nitric acid, temperature and γ-irradiation had been investigated. The adsorption property of the treated TODGA/SiO₂-P was evaluated by a 3 M HNO₃ solution containing 0.01 M Nd(III). It was found that both 3 and 0.01 M HNO₃ concentrations did not decrease the stability of TODGA/SiO₂-P at 25°C. The quantity of TODGA leaked from TODGA/SiO₂-P was equivalent to its solubility in the corresponding HNO₃ aqueous solution. The effect of 3 M HNO₃ on the leakage of TODGA at 80°C was significantly higher than that in 0.01 M HNO₃ as well as in all cases at 25°C. The amount of Nd(III) adsorbed towards the treated TODGA/SiO₂-P was determined in the range of 0.143–0.148 mmol/g for the HNO₃ concentration effect and 0.142–0.0506 mmol/g for the temperature effect. γ-Irradiation showed a more noticeable destruction effect on TODGA/SiO₂-P. The content of TODGA leaked increased with an increase in the γ-irradiation dose (ID) from 1.06 to 3.72 MGy in terms of the linear equation [TODGA]=794.5ID+84.0. The amount of Nd(III) adsorbed onto the irradiated TODGA/SiO₂-P decreased rapidly from 0.134 to 0.0438 mmol/g, which was lower than 0.153 mmol/g, the adsorption of fresh TODGA/SiO₂-P for Nd(III), according to the equation Q_Nd(III)=−0.0301ID+0.160, showing that a large quantity of TODGA leaked from TODGA/SiO₂-P. The adsorbed amount of Nd(III) decreased obviously in this order: the HNO₃ concentration effect, temperature effect and γ-irradiation.     

Polysulfone ionomers for proton-conducting fuel cell membranes: sulfoalkylated polysulfones

Polysulfones (PSUs) carrying short pendant alkyl side-chains with terminal sulfonic acid units have been prepared and studied as proton-conducting membrane materials. The first step in the preparation involved quenching of lithiated PSU with SO₂ gas, resulting in sulfinated PSU. In the second step, the lithium sulfinate units on the polymer were reacted with sodium 2-bromoethanesulfonate, sodium 3-bromopropanesulfonate, or 1,4-butane sultone to produce sulfoethylated, sulfopropylated, or sulfobutylated PSUs, respectively. Analysis by thermogravimetry showed that membranes based on the sulfoalkylated polymers were stable up to approximately 300 °C under N₂ atmosphere. Calorimetry measurements revealed that the modified polymers absorbed large amounts of non-freezing water, corresponding to 11–14 mol H₂O/mol SO₃H under immersed conditions. The proton conductivity of a membrane based on a PSU carrying 0.9 sulfopropyl chains per repeating unit was measured to be 77 mS/cm at 70 °C under humidifying conditions.     

Chains, ladders and sheets of d metal–organic polymers generated from the flexible bipyridyl ligands

By use of the three-layer diffusion method, reactions of flexible bipyridyl ligands (4,4′-bpp or 3,3′-bpp) with M(II) salts (M = Zn, Cd) and multi-carboxylate ligands resulted in the formation of four interesting d¹⁰ metal–organic coordination polymers: [Zn(μ-4,4′-bpp)Br₂]_n (1), [Zn(μ-4,4′-bpp)(1,2-bdc)]_n · nH₂O (2), [Zn(μ-3,3′-bpp)(1,3-bdc)]_n · nCH₃OH · 2nH₂O (3) and [Cd(μ-3,3′-bpp)(C₄H₂O₄)]_n · 3nH₂O (4) (4,4′-bpp = 2,2′-bis(4-pyridylmethyleneoxy)-1,1′-biphenylene; 3,3′-bpp = 2,2 ′-bis(3-pyridylmethyleneoxy)-1,1′-biphenylene; bdc=benzenedicarboxylate, C₄H₄O₄ = fumaric acid). Complex 1 has a 2D sheet structure consisting of two unusual zigzag Zn(II) chains which are nearly perpendicular to each other. Complex 2 is comprised of two-leg ladders, in which [Zn(4,4′-bpp)] chains serve as the side rails and 1,2-bdc ligands serve as the cross rungs. In complex 3, every two 1,3-bdc ligands connect the neighbouring Zn(II)-3,3′-bpp dimetallic rings in η¹ coordination modes into an interesting chain structure. Complex 4 consists of an anionic macrocycle-containing cadmium dicarboxylate sheets that are separated by 3,3′-bpp. These d¹⁰ metal complexes exhibit high thermal stabilities and strong luminescence efficiencies.     

Membrane purification of Cl2 gas: I. Permeabilities as a function of temperature for Cl2, O2, N2, H2 in two types of PDMS membranes

Permeability (P) of Cl₂, O₂, N₂ and H₂ was measured in polydimethylsiloxane (PDMS) composite membranes with two different degrees of cross-linking. The permeability was measured in the low pressure range (1–3 bar absolute) over a fairly large temperature range 35–120°C. The functionalities of the membranes were compared on the basis of permeation rate and ability to separate the gases Cl₂–O₂. These results are part of an extensive survey where perfluorinated and carbon membranes are also included (not reported here). The purpose of the project is to develop an industrial membrane with high permselectivity for either O₂ or Cl₂ (depending on the type of membrane) at temperatures preferably above 70°C. Process conditions are set in an industrial project. The PDMS membranes are good candidates for this separation, having a high permeation rate for Cl₂ and a selectivity of Cl₂/O₂ in the range of 8–25 depending on temperature. Durability of the PDMS membranes in this aggressive environment is found to be very dependent on process conditions and on how the material is polymerized and cured. For documentation of durability, various silicones were tested; these results are to be reported separately.     

Pd encapsulated and nanopore hollow fiber membranes: Synthesis and permeation studies

New types of supported Pd membranes were developed for high temperature H₂ separation. Sequential combinations of boehmite sol slip casting and film coating, and electroless plating (ELP) steps were designed to synthesize “Pd encapsulated” and “Pd nanopore” membranes supported on -Al₂O₃ hollow fibers. The permeation characteristics (flux, permselectivity) of a series of unaged and aged encapsulated and nanopore membranes with different Pd loadings were compared to those of a conventional 1 μm Pd/4 μm γ-Al₂O₃/-Al₂O₃ hollow fiber membrane. The unaged encapsulated membrane exhibited good performance with ideal H₂/N₂ separation factors of 3000–8000 and H₂ flux 0.4 mol/m² s at 370 °C and a transmembrane pressure gradient of 4 × 10⁵ Pa. The unaged Pd nanopore membranes had a lower initial flux and permselectivity, but exhibited superior performance with extended use (200 h). At the same conditions the unaged 2.6 μm Pd nanopore membrane had a H₂ flux of 0.16 mol/m² s and separation factor of 500 and the unaged 0.6 μm Pd nanopore membrane had a H₂ flux of 0.25 mol/m² s and separation factor of 50. Both nanopore membranes stabilized after 40 h of operation, in contrast to a continued deterioration of the permselectivity for the other membranes. An analysis of the permeation data reveals a combination of Knudsen and convective transport through membrane defects. A phenomenological, qualitative model of the synthesis and resulting structure of the encapsulated and nanopore membranes is presented to explain the permeation results.     

Structures of 3,3′-dicarbometoxy-2,2′-bipyridine complexes with silver(I) and copper(II) cations

The structures of 3,3′-dicarbometoxy-2,2′-bipyridine (dcmbpy) complexes with copper(II) and silver(I) cations have been determined using single crystal X-ray-diffraction. The crystals of Cu(dcmbpy)Cl₂ are monoclinic, C2/c, a = 16.966(3), b = 18.373(3), c = 13.154(2) Å, β = 126.543(3)°. The crystals of Ag(dcmbpy)NO₃ · H₂O are also monoclinic, C2/c, a = 16.7547(13), b = 11.0922(9), c = 18.7789(18) Å, β = 100.228(7)°. The results have been compared with the literature data on the complexes of dcmbpy and its precursors: 2,2′-bipyridine (bpy) and 3,3′-dicarboxy-2,2′-bipyridine (dcbpy). Two types of complexes of 3,3′-carboxy derivatives of bpy are distinguished: (1) with metal atom bonded to two N atoms of the same molecule and (2) with metal atom bonded to two N atoms of two different molecules. The Cu(dcmbpy)Cl₂ complex belongs to the first type, whereas Ag(dcmbpy)NO₃ · H₂O belongs to the second type.     

Olefin polymerization by (cyclopentadienyl)(ketimide)titanium(IV) complexes of the type, Cp′TiCl2(N=CBu2)-methylaluminoxane (MAO) catalyst systems

Effects of substituents on cyclopentadienyl group for homopolymerization of ethylene, 1-hexene, and for ethylene/1-hexene copolymerization using a series of nonbridged (cyclopentadienyl)(ketimide)titanium complexes of the type, Cp′TiCl₂(N=C^tBu₂) [Cp′ = Cp (1), ^tBuC₅H₄ (2), C₅Me₅ (Cp^*, 3), and indenyl (4)] have been explored in the presence of methylaluminoxane (MAO) cocatalyst. Complexes 1–3 showed the similar catalytic activities for ethylene polymerization although the activity by 4 was somewhat low, whereas the activity for 1-hexene polymerization increased in the order 1 > 4 2 > 3. These complexes showed significant activities for ethylene/1-hexene copolymerization affording high molecular weight poly(ethylene-co-1-hexene)s with unimodal molecular weight distributions, and the activity increased in the order: 4 > 1 2, 3. The r_Er_H values in the polymerization by 1–3 at 40 °C were 0.35–0.52 which clearly indicate that the 1-hexene incorporation in the copolymerization did not proceed in a random manner. The r_E values by 1–3 were 6.0–6.4 and the values were independent upon the cyclopentadienyl fragment employed; the r_E values by 4 at 40 °C were 10.2–10.9 which were close to those by ansa-metallocene complex catalysts. These values were influenced by the polymerization temperature, and the 1-hexene incorporation by 1–4 became inefficient at higher temperature, although the observed activities especially by 1, 4 were highly remarkable.     

Synthesis and structures of three 1-aminoethylidenediphosphonate compounds with transition-metal ions

Three new aminodiphosphonates, namely M(phen)(AEDPH₃)₂·4H₂O (M = Zn, (1); Ni, (2)) and Cu(phen)(AEDPH₃)₂·H₂O (4), in addition to the previously reported Co(phen)(AEDPH₃)₂·4H₂O (3), Cu(2,2′-bipy)(H₂O)(HEDPH₂)·2H₂O (5), and Cu(phen)(H₂O)(HEDPH₂)·2H₂O (6) (AEDPH₄ = 1-aminoethylidenediphosphonic acid, HEDPH₄ = 1-hydroxyethylidenediphosphonic acid, phen = 1,10-phenanthroline and 2,2′-bipy = 2,2′-bipyridyl), have been synthesized and characterized. These compounds are all synthesized at the similar condition (80 °C), whereas they illustrate different frameworks. Compounds 1, 2 and 3 are isomorphous, which contain two same chelate and one six-coordinated metal ion, and display a three-dimensional (3D) supramolecular structure through hydrogen bonds and π–π stacking interactions. Compound 4 contains a chelate and a monodentate , while the Cu ion is five-coordinated. The coordination model of Cu²⁺ in 4 is similar to that of 5 and 6. Comparing with four aminoethylidenediphosphonates, the difference of their structures is directed to the coordination model of the metal ions, while the three copper(II) diphosphonates illustrate different structures based on the deprotonized degree of the corresponding diphosphonic acids.     

Preparation and characterization of CPPO/BPPO blend membranes for potential application in alkaline direct methanol fuel cell

A series of hydroxyl-conducting anion-exchange membranes were prepared by blending chloroacetylated poly(2,6-dimethyl-1,4-phenylene oxide) (CPPO) with bromomethylated poly(2,6-dimethyl-1,4-phenylene oxide) (BPPO), and their fuel cell-related performances were evaluated. The resulting membranes exhibited high hydroxyl conductivities (0.022–0.032 S cm⁻¹ at 25 °C) and low methanol permeability (1.35 × 10⁻⁷ to 1.46 × 10⁻⁷ cm² s⁻¹). All the blend membranes proved to be miscible or partially miscible under the investigations of scanning electron microscopy (SEM) and differential scanning calorimeters (DSC). By condition optimization, the blend membranes with 30–40 wt% CPPO are recommended for application in direct methanol alkaline fuel cells because they showed low methanol permeability, excellent mechanical properties and comparatively high hydroxyl conductivity.     

Synthesis, water stability and proton conductivity of novel sulfonated polyimides from 4,4′-bis(4-aminophenoxy)biphenyl-3,3′-disulfonic acid

A novel sulfonated diamine monomer, 4,4′-bis(4-aminophenoxy)biphenyl-3,3′-disulfonic acid (BAPBDS) with the high basisity and flexible structure was synthesized by direct sulfonation of 4,4′-bis(4-aminophenoxy)biphenyl (BAPB). Sulfonated polyimides (SPIs) were prepared from 1,4,5,8-naphthalenetetracarboxylic dianhydride (NTDA), BAPBDS and nonsulfonated diamines such as BAPB. The SPI membranes showed much higher water stability at high temperatures than other sulfonated diamine-based SPIs reported so far. Their water vapor sorption isotherm, water uptake (WU), density, dimensional change and proton conductivity σ were investigated. The SPIs showed rather isotropic dimensional changes with WU and the volume increases were slightly smaller than those estimated from the additivity. The SPIs with ion exchange capacities (IECs) of 1.9–2.7 meq/g displayed the similar relationship between σ and WU each other, which was different from those of Nafion 117 and also of the SPIs with the lower IECs. The former SPIs showed reasonably high σ values of 10⁻² S/cm or more even at WU of 25 g/100 g dry polymer under 70% RH at 50 °C, whereas the latter showed the similarly high σ values only in liquid water, but not in the nearly saturated water vapor.