Combined slit and plate–plate magnetorheometry of a magnetorheological fluid (MRF) and parameterization using the Casson model

We describe a magneto-slit die of 0.34 mm height and 4.25 mm width attached to a commercial piston capillary rheometer, enabling the measurement of apparent flow curves of a magnetorheological fluid (MRF) in the high shear rate regime (apparent shear rates 276 up to 20,700 s^???1, magnetic flux density up to 300 mT). The pressure gradient in the magnetized slit is measured via two pressure holes. While the flux density versus coil current without MRF could directly be measured by means of a Hall probe, the flux density with MRF was investigated by finite element simulations using Maxwell® 2D. The true shear stress versus shear rate is obtained by means of the Weissenberg–Rabinowitsch correction. The slit die results are compared to plate–plate measurements performed in a shear rate regime of 0.46 up to 210 s^???1. It is shown that the Casson model yields a pertinent fit of the true shear stress versus shear rate data from plate–plate geometry. Finally, a joint fit of the slit and plate–plate data covering a shear rate range of 1 up to 50,000 s^???1 is presented, again using the Casson model. The parameterization of the MRF behavior over the full shear rate regime investigated is of relevance for the design of MR devices, like, e.g., automotive dampers. In the Appendix, we demonstrate the drawbacks of the Bingham model in describing the same data. We also show the parameterization of the flow curves by applying the Herschel–Bulkley model.     

Annular Pulse Shaping Technique for Large-Diameter Kolsky Bar Experiments on Concrete

The goal of this study is to design a novel annular pulse shaping technique for large-diameter Kolsky bars for investigating the dynamic compressive response of concretes. The purpose of implementing an annular pulse shaper design is to alleviate inertia-induced stresses in the pulse shaper material that would otherwise superpose unwanted oscillations on the incident wave. This newly developed pulse shaping technique led to well-controlled testing conditions enabling dynamic stress equilibrium, uniform deformation, and constant strain-rate in the testing of a chosen concrete material. The observed dynamic deformation rate of the concrete is highly consistent (8 % variation) with the stress in the specimen well equilibrated confirming the validity of this new technique. Experimental results at both quasi-static (10^?4 s^?1) and dynamic (100 s^?1, 240 s^?1) strain rates showed that the failure strength of this concrete is rate-sensitive.     

Strain-rate history and temperature effects on the torsional-shear behavior of a mild steel

Previous investigations on the effects of strain-rate and temperature histories on the mechanical behavior of steel are briefly reviewed. A study is presented on the influence of strain rate and strain-rate history on the shear behavior of a mild steel, over a wide range of temperature Experiments were performed on thin-walled tubular specimens of short gage length, using a torsional split-Hopkinson-bar apparatus adapted to permit quasi-static as well as dynamic straining at different temperatures. The constant-rate behavior was first measured at nominal strain rates of 10^?3 and 10³ s^?1 for ?150, ?100, ?50, 20, 200 and 400°C. Tests were then carried out, at the same temperatures, in which the strain rate was suddenly increased during deformation from the lower to the higher rate at various large values of plastic strain. The increase in rate occurred in a time of the order of 20 μs so that relatively little change of strain took place during the jump. The low strain-rate results show a well-defined elastic limit but no yield drop, a small yield plateau is found at room temperature. The subsequent strain hardening shows a maximum at 200°C, when serrated flow occurs and the ductility is reduced. The high strain-rate results show a considerable drop of stress at yield. The post-yield flow stress decreases steadily with increasing temperature, throughout the temperature range investigated. At room temperature and below, the strain-hardening rate becomes negative at large strains. The adiabatic temperature rise in the dynamic tests was computed on the assumption that the plastic work is entirely converted to heat. This enabled the isothermal dynamic stress-strain curves to be calculated, and showed that considerable thermal softening took place. The initial response to a strain-rate jump is approximately elastic, and has a magnitude which increases with decrease of testing temperature; it is little affected by the amount of prestrain. At 200 and 400° C, a yield drop occurs after the initial stress increment. The post-jump flow stress is always greater than that for the same strain in a constant-rate dynamic test, the strain-hardening rate becoming negative at large strains or low testing temperature. This observed effect of strain-rate history cannot be explained by the thermal softening accompanying dynamic deformation. These and other results concerning total ductility under various strain-rate and temperature conditions show that strain-rate history strongly affects the mechanical behavior of the mild steel tested and, hence, should be taken into account in the formulation of constitutive equations for that material.     

The effect of strain rate and heat developed during deformation on the stress-strain curve of plastics

Polymethylmethacrylate, cellulose acetate butyrate, polypropylene and nylon 6–6 have been characterized in compression at various strain rates from 10^?4 s^?1 to 10³ s^?1 at room temperature. A medium strain-rate machine and a split-Hopkinson-bar apparatus are used in conducting the experiments. The temperature rise developed during deformation is also measured by using a thermocouple. All four materials tested definitely show a viscous effect at the beginning of the deformation and a plastic flow follows thereafter. Test results also indicate that the temperature rise developed during deformation cannot be neglected in determining the dynamic response of those materials investigated in this study.     

Influence of Mass Ratio on Forward and Reverse Ballistic Impact Equivalence: Experiments,Simulations, and Mechanism Analysis

Reverse ballistic impact tests are widely used for studying dynamic responses because they provide more comprehensive and quantitative projectile/rod response results than forward impact tests. To examine equivalent forward and reverse conditions, a series of 8-cm length oxygen-free copper rods with varying length–diameter ratios was used in forward and reverse ballistic Taylor impact experiments with velocities and strain ratios of 104–215 m/s and 1.25?×?10³–2.5?×?10³ s^-1, respectively. Digital image correlation (DIC) and traditional optical measurements were used to determine instantaneous responses at the μs level. Based on DIC, transient structural deformation, and plastic wave propagation, the forward and reverse length difference at similar velocities ranges from 2 to 6.95 %. Rules governing deformation from the perspective of energy, along with rules for changes in energy and plastic wave propagation were determined. The relative deformation energy error was below 5 % for target projectile mass ratios above 20.     

High strain-rate crack growth in rate-dependent plastic solids

At high crack velocities in metallic materials nearly all plastic strain accumulates at very high strain-rates, typically in the range 10³ s^?1 to 10⁵ s^?1. At these rates, dislocation motion is limited by dynamic lattice effects and the plastic strain-rate increases approximately linearly with stress. The problem for a crack growing at high velocity is posed for steady-state, small scale yielding in elastic/rate-dependent plastic solids. A general expression is derived for the near-tip stress intensity factor in terms of the remote intensity factor, or equivalently for the near-tip energy release-rate in terms of the overall release-rate. An approximate calculation of the plastic strain-rates provides this relation in analytical form. Imposition of the condition that the near-tip energy release-rate be maintained at a critical value provides a propagation equation for the growing crack. A single, nondimensional combination of material constants emerges as the controlling parameter. Implications for dynamic crack propagation are discussed.     

Anisotropic responses, constitutive modeling and the effects of strain-rate and temperature on the formability of an aluminum alloy

Finite deformation anisotropic responses of AA5182-O, over a wide range of strain-rates (10⁻⁴ to 10⁰ s⁻¹) and temperatures (293-473 K) are presented. The plastic anisotropy parameters were experimentally determined from tensile experiments using specimens from sheet material. Using the experimental results under plane stress conditions, the anisotropy coefficients for Barlat’s yield function (YLD96) were calculated at different strain-rates and temperatures. The correlations obtained from YLD96 are in good agreement with the observed experimental results. The strain-rate sensitivity of AA5182-O alloy changed from negative at 293 K to positive at 473 K. Khan-Huang-Liang (KHL) constitutive model is shown to correlate the observed strain-rate and temperature dependent responses reasonably well. The material parameters were obtained from the experimental responses along the rolling direction (RD) of the sheet. Marciniak and Kuckzinsky (M-K) theory was used to obtain the theoretical strain and stress-based forming limit curves (FLCs) at different strain-rates and temperatures. The experimental result from the published literature is compared with the FLCs from the current study.     

Behaviors of three BCC metal over a wide range of strain rates and temperatures: experiments and modeling

The elastic–plastic behaviors of three body-centered cubic metals, tantalum, tantalum alloy with 2.5% tungsten, and AerMet 100 steel, are presented over a wide range of strains (15%), strain rates (10⁻⁶–10⁴ s⁻¹) and temperatures (77–600°F). Johnson-Cook and Zerilli-Armstrong models were found inadequate to describe the observations. A new viscoplastic model is proposed based on these experimental results. The proposed constitutive model gives good correlations with these experimental results and strain-rate jump experiments. In the next paper (Liang, R., Khan A.S., 2000. Behaviors of three BCC metals during non-proportional multi-axial loadings and predictions using a recently proposed model. International Journal of Plasticity, in press), multi-axial loading results on these materials and comparison with the proposed model will be presented.     

超强钢18NiC250在不同加载速率下的断裂韧性

为了揭示国产超强钢18NiC250的强度、断裂韧性随加载速率的变化规律,利用电子万能试验机和Hopkinson压杆,测试其在0.001～2 000 s-1的塑性流动应力应变曲线及在10-1~106 MPam1/2/s的断裂韧性,同时对断裂破坏机理进行了微观分析。结果表明:该材料的强度对加载速率不敏感,即流动应力基本保持在1.9 GPa;而断裂韧性很敏感,当加载速率由10-1 MPam1/2/s增大到106 MPam1/2/s时,断裂韧性降低了38.2%,断裂模式由韧窝断裂转变为解理断裂。     

Synchronous Full-Field Strain and Temperature Measurement in Tensile Tests at Low,Intermediate and High Strain Rates

Tensile tests with simultaneous full-field strain and temperature measurements at the nominal strain rates of 0.01, 0.1, 1, 200 and 3000 s^?1 are presented. Three different testing methods with specimens of the same thin and flat gage-section geometry are utilized. The full-field deformation is measured on one side of the specimen, using the DIC technique with low and high speed visible cameras, and the full-field temperature is measured on the opposite side using an IR camera. Austenitic stainless steel is used as the test material. The results show that a similar deformation pattern evolves at all strain rates with an initial uniform deformation up to the strain of 0.25–0.35, followed by necking with localized deformation with a maximum strain of 0.7–0.95. The strain rate in the necking regions can exceed three times the nominal strain rate. The duration of the tests vary from 57 s at the lowest strain rate to 197 μs at the highest strain rate. The results show temperature rise at all strain rates. The temperature rise increases with strain rate as the test duration shortens and there is less time for the heat to dissipate. At a strain rate of 0.01 s^?1 the temperature rise is small (up to 48 °C) but noticeable. At a strain rate of 0.1 the temperature rises up to 140 °C and at a strain rate of 1 s^?1 up to 260 °C. The temperature increase in the tests at strain rates of 200 s^?1 and 3000 s^?1 is nearly the same with the maximum temperature reaching 375 °C.     

A Novel Image-based Ultrasonic Test to Map Material Mechanical Properties at High Strain-rates

An innovative identification strategy based on high power ultrasonic loading together with both infrared thermography and ultra-high speed imaging is presented in this article. It was shown to be able to characterize the visco-elastic behaviour of a polymer specimen (PMMA) from a single sample over a range of temperatures and strain-rates. The paper focuses on moderate strain-rates, i.e. from 10 to 200 s^?1, and temperatures ranging from room to the material glass transition temperature, i.e. 110^°C. The main originality lies in the fact that contrary to conventional Dynamic Mechanical Thermal Analysis (DMTA), no frequency or temperature sweep is required since the experiment is designed to simultaneously produce both a heterogeneous strain-rate state and a heterogeneous temperature state allowing a local and multi-parametric identification. This article is seminal in nature and the test presented here has good potential to tackle a range of other types of high strain-rate testing situations.     

Dehydration characteristics and mathematical modelling of lemon slices drying undergoing oven treatment

In this study, the effect of drying temperature on drying behaviour and mass transfer parameters of lemon slices was investigated. The drying experiments were conducted in a laboratory air ventilated oven dryer at temperatures of 50, 60 and 75 °C. It was observed that the drying temperature affected the drying time and drying rate significantly. Drying rate curves revealed that the process at the temperature levels taken place in the falling rate period entirely. The usefulness of eight thin layer models to simulate the drying kinetics was evaluated and the Midilli and Kucuk model showed the best fit to experimental drying curves. The effective moisture diffusivity was determined on the basis of Fick’s second law and obtained to be 1.62 × 10^?11, 3.25 × 10^?11 and 8.11 × 10^?11 m² s^?1 for the temperatures of 50, 60 and 75 °C, respectively. The activation energy and Arrhenius constant were calculated to be 60.08 kJ mol^?1 and 0.08511 m² s^?1, respectively. The average value of convective mass transfer coefficient for the drying temperatures of 50, 60 and 75 °C was calculated to be 5.71 × 10^?7, 1.62 × 10^?6 and 2.53 × 10^?6 m s^?1, respectively.     

Evaluation of the Material Properties of an OFHC Copper Film at High Strain Rates Using a Micro-Testing Machine

The material properties of an oxygen-free high thermal conductivity (OFHC) film with a thickness of 0.1 mm were evaluated at strain rates ranging from 10⁻³/s to 10³/s using a high-speed material micro-testing machine (HSMMTM). The high strain-rate material properties of thin films are important especially for an evaluation of the structural reliability of micro-formed parts and MEMS products. The high strain-rate material testing methods of thin films, however, have yet to be established to the point that the testing methods of larger specimens for electronics, auto-body, train, ship, and ocean structures are. For evaluation, a new type of HSMMTM was developed to conduct high-speed tensile tests of thin films. This machine is capable of testing at a sufficiently high tensile speed with an electromagnetic actuator, a novel gripping mechanism, and an accurate load measurement system. The OFHC copper film shows high strain-rate sensitivity in terms of the flow stress, fracture elongation, and strain hardening. These measures increase as the tensile strain rate increases. The rate-dependent material properties of an OFHC copper film are also compared with those of a bulk OFHC copper sheet with a thickness of 1 mm. The flow stress of an OFHC copper film is relatively low compared to that of a bulk OFHC copper sheet in the entire range of strain rates, while the fracture elongation of an OFHC copper film is much larger than that of a bulk OFHC copper sheet. A quantitative comparison would provide material data at high strain rates for the design and analysis of micro-appliances and different types of micro-equipment.     

Influence of Molecular Conformation on the Constitutive Response of Polyethylene: A Comparison of HDPE, UHMWPE, and PEX

The current work presents the characterization and comparison of the mechanical response of three different industrial forms of polyethylene. Specifically, high-density polyethylene (HDPE), ultra high molecular weight polyethylene (UHMWPE), and cross-linked polyethylene (PEX) were tested in compression as a function of temperature (−75 to 100°C) and strain-rate (10⁻⁴ to 2,600 s⁻¹). The responses of UHMWPE and PEX are very similar, whereas HDPE exhibits some differences. The HDPE samples display a significantly higher yield stress followed by a flat flow behavior. Conversely UHMWPE and PEX both exhibit significant strain hardening after yield. The temperature and strain-rate dependence are captured by simple linear and logarithmic fits over the full range of conditions investigated. The yield behavior is presented in terms of an empirical mapping function that is extended to analytically solve for the mapping constant. The power-law dependence on strain-rate observed in some polymers is explained using this mapping function.     

Role of strain-rate sensitivity in the crystal plasticity of hexagonal structures

In the first part of this paper the stress and strain-rate response of hexagonal crystal structures are examined when slip is viscoplastic according to a power law. The stress and strain-rate equi-potential surfaces are constructed and discussed as a function of the strain-rate sensitivity index m. The second part of this paper deals with the case of linear viscous slip; i.e., for the case when m is equal to one. A simple analytic solution is presented to obtain the deviatoric stress state for a given strain-rate. It is shown that the plastic spin is not zero for m = 1 in hexagonal crystal structures, contrary to the cubic case where the plastic spin vanishes. In addition, the rate of texture evolution in simple shear of a magnesium polycrystal is examined as a function of m.     

Effect of oxygen content and microstructure on the thermo-mechanical response of three Ti–6Al–4V alloys: Experiments and modeling over a wide range of strain-rates and temperatures

Results from a series of experiments on three different titanium alloys, under quasi-static and dynamic loading conditions are presented. The Ti–6Al–4V titanium alloys include the ELI version and two with higher oxygen contents. The strain-rates are varied from 10⁻⁶ to 3378 s⁻¹ while observations are made at temperatures from 233 to 755 K. The alloys initial and deformed photomicrographs and various deformation mechanisms responsible for the induced plastic deformation, are presented and discussed. Differences in the responses of these alloys are observed in terms of thermal softening, work hardening, and strain-rate and temperature sensitivities. The Khan–Huang–Liang (KHL) model is used to effectively simulate the observed responses obtained from these experiments. The model, with the constants determined from these experiments, is then used to predict strain-rate jump experimental results, and also high temperature dynamic experiments for one of the alloys; the predictions are found to be very close to the observations.     

Constitutive modeling of the dynamic fracture of smooth tensile bars

A recently developed viscoplastic-damage type of constitutive theory for high strain-rate flow processes and ductile fracture is used to model the deformation and fracture of dynamically loaded smooth cylindrical tensile bars. The analysis assumes polycrystalline materials which usually contain microvoids with an average density of the order of 10⁶ per cm³ that are dispersed homogeneously throughout. It is shown that for dynamically imposed loading that produce nominal strain rates ranging between 5 × 10² − 5 × 10³ sec ⁻¹, the inhomogeneous fields of stress and deformation caused by wave propagation and wave reflection induce necking at different locations along the gauge section, depending upon the strain-rate imposed. This occurs without imposition of any geometrical or material irregularity to preposition the location of the necking. The imposed rate of strain is also shown to affect the magnitude of the strain at which necking initiates, as well as the strain required for fracture.     

45钢柱壳膨胀断裂的应变率效应

采用前照明高速分幅照相技术拍摄到在爆轰加载下45钢柱壳表面裂纹生成、扩展及产物泄漏过程的清晰图像,较准确地测量了膨胀断裂的时间与应变。 45钢柱壳在炸药爆轰加载下,断裂应变随应变率的增加而增加,当应变率达到一定值,断裂应变随应变率的增加而降低,出现了动态断裂中的塑性峰现象。     

Stress-strain relationships for spruce wood: Influence of strain rate,moisture content and loading direction

The influence of strain rate, moisture content and loading direction on the stress-strain relationships for spruce wood has been investigated. The strain rates were approximately 8×10⁻³ s⁻¹, 17s⁻¹ and 1000 s⁻¹, and the states of moisture content were those corresponding to oven dry, fiber saturated and fully saturated. Compressive loads were applied along the principal directions of the stem of the tree, i.e., radially, tangentially and axially. The low and medium strain-rate tests were performed with the aid of a servohydraulic testing machine, while the high strain-rate tests were carried out using the split Hopkinson pressure bar (SHPB) technique. Magnesium or steel bars were used in the different SHPB tests in order to reduce impedance mismatch for the different directions of the wood specimens. The strain rate was found to have large influence on the behavior of the wood, especially under the condition of full saturation, where water transport in the deforming specimen is of major importance.     

Compression-impact testing of aluminum at elevated temperatures

This paper presents and experimental technique for determining compressive stress-strain curves well into the plastic range of relatively soft metals at strain rates from 300 to 2000 sec^?1 at six temperatures from 30 to 550° C. More than 100 curves were obtained on annealed 1100° F aluminum. The strain-rate dependence in these tests could be fitted quite well either by a power function (log-log plot) or by a semilogarithmic plot, but the power function gave a better correlation of the present data with that obtained at lower strain rates by Alder and Phillips.¹