纳米Fe3O4分离富集-悬浮进样-氢化物发生原子荧光法测定砷形态

研究了以纳米Fe3O4为固相吸附剂对痕量无机砷形态的吸附与分离富集,建立了无需洗脱分离的悬浮进样-氢化物发生-原子荧光法测定砷形态的方法。选择的反应体系为0.64 g/L Fe3O4悬浮液-1.0%(m/V)NaBH4溶液-5.0%(V/V)HCl(pH 8),进样5.0 mL时,得到本方法的检出限为13.5 ng/L;As(Ⅲ)浓度在0.05～3.5μg/L范围内呈良好的线性关系;测定0.5μg/L As(Ⅲ)的精密度RSD=3.4%。用国家标准物质GBW10010(大米)验证了本方法测定砷的准确性,测定结果(0.101±0.010μg/g)与标准值(0.102±0.008μg/g)吻合。采用本方法测定了近海海水和雪水样品中的无机砷形态,并进行了加标回收实验。对As(Ⅲ)和As(Ⅴ)的加标回收率在95%～110%之间,结果令人满意。     

新型磷酸盐受体的合成与性能研究

由二茂铁经甲酰基化、氧化和酰氯化制备的1，1′-二茂铁二酰氯与对苯二胺和对硝基苯胺缩合反应，合成了新型磷酸盐敏感试剂：1，1′-二[(对苯二胺基)-N-羰基]-二茂铁(L1)和1，1′-二[(对硝基苯胺基)-N-羰基]二茂铁(L)，并研究了Ll，L2与磷酸盐阴离子的电子结合性能。Ll，L2对磷酸盐响应灵敏。Ll对H2PO4^-响应的线性为1．00μg/mL～10．00μg/mL，检测限(3σ／k)为0．01μg/mL；也对PO4^3-响应的线性为6．60μg/mL～54．50μg/mL，检测限(3σ／k)为0．03μg/mL。     

HPLC–AFS联用测定海产品中砷的形态

建立了高效液相色谱–原子荧光分光光度法测定海产品中无机砷(As V,AsⅢ)、有机砷(DMA,MMA,AsB)含量的方法。样品经含10%(体积分数)HCl的提取液振荡提取、离心分离、二路形态分析预处理、高效液相色谱分离,用原子荧光光度计检测As(Ⅲ),DMA,MMA,As(V);四路条件(过氧化氢氧化和开启紫外灯)形态分析预处理装置处理,高效液相色谱分离,原子荧光光度计测定AsB。As(Ⅲ)线性范围为0～100.00μg/L,r2=0.999 7;DMA线性范围为0～100.00μg/L,r2=0.999 3;MMA线性范围为0～100.00μg/L,r2=0.999 0;As(V)线性范围为0～100.00μg/L,r2=0.999 1;AsB线性范围为0～200.00μg/L,r2=0.999 4。3个样品加标回收率为As(Ⅲ)86.7%～89.4%,DMA 111.2%～117.0%,MMA 109.7%～111.6%,As(V)83.8%～90.7%,AsB 88.3%～90.4%。用该方法测定虾仁(干)5个价态测定结果的相对标准偏差为3.07%～9.93%(n=6)。5个价态的检出限(S/N=2)为As(Ⅲ)0.29μg/L,DMA 0.36μg/L,MMA 0.27μg/L,As(V)0.56μg/L,AsB 1.46μg/L。该方法适用于海产品中As(Ⅲ),DMA,MMA,As(V),AsB含量的测定。     

固相支持液-液萃取/液相色谱-串联质谱法测定人全血中环孢素A

采用固相支持液-液萃取/液相色谱-串联质谱(LC-MS/MS)技术建立了人全血中环孢素A的分析方法。全血样品经蛋白沉淀后,上样至固相支持液-液萃取柱,经甲基叔丁基醚洗脱,Shim-pack XR-ODS色谱柱(75 mm×3. 0 mm i. d.,2. 2μm)分离,电喷雾电离源、正离子模式和多反应监测模式下采集数据,以环孢素D为内标物定量。结果表明,环孢素A在1. 5～500μg/L范围内呈良好的线性关系,相关系数(r)为0. 998,检出限和定量下限分别为0. 5μg/L和1. 5μg/L,在50、100、400μg/L 3个加标浓度下的平均回收率为78. 6%～83. 5%,日内和日间相对标准偏差(n=3)分别为3. 1%～5. 6%和4. 5%～8. 3%。该方法操作简便、灵敏度高,可用于全血中环孢素A的分析。     

固相萃取-超高效液相色谱串联质谱法测定水中13种苯胺类化合物

建立了固相萃取-超高效液相色谱串联质谱法测定水中13种苯胺类化合物。样品通过HC-C₁₈固相萃取小柱富集，洗脱后加入内标苯胺-D5进行氮吹浓缩，经HSS T3色谱柱(150 mm×2.1 mm,1.8μm)分离，采用多反应监测扫描模式，以内标法定量。13种苯胺类化合物在0.1～100μg/L(其中3-硝基苯胺为0.2～200μg/L)范围内与特征离子的色谱峰面积线性关系良好，相关系数均大于0.995，方法检出限为0.001～0.006μg/L，平均加标回收率为67.3%～117%，测定结果的相对标准偏差为3.77%～16.9%(n=6)。该法操作简单、稳定性好，能够满足实际水体中13种苯胺类化合物大批量样品分析的需求。     

二甲基黄催化动力学光度法测定痕量钯

根据在 H2 SO4 介质中钯 ( )催化高碘酸钾氧化二甲基黄的褪色反应 ,提出了测定钯的新催化光度法。钯浓度在 0 .0～ 6.0μg/2 5 m L范围内与催化反应速率呈良好的线性关系。方法的检出限为 2 .1 9× 1 0 - 3μg /m L。对 3.0μg/2 5 m L钯 ( )测定的相对标准偏差为 0 .78% ( n=1 1 )。此法用于某些催化剂中钯的测定 ,标准加入回收率为 99.5 %～ 1 0 4 .1 %。     

浊点萃取-气相色谱-质谱法测定水中9种芳香胺类化合物

本研究基于以曲拉通X-114(Triton X-114)为萃取剂的浊点萃取技术和气相色谱-质谱法,建立了一种高效、高灵敏度的水体中9种芳香胺(2-氯胺、3-氯胺、4-氯胺、2-硝基苯胺、3-硝基苯胺、4-硝基苯胺、1-萘胺、2-萘胺和4-氨基联苯)的检测方法。采用单因素优化法对影响提取效果的重要因素进行了优化。采用气相色谱-质谱对水中9种芳香胺进行定性、定量分析,使用中等极性色谱柱DB-35 MS(30 m×0.25 mm×0.25μm)进行分离,在选择离子模式(SIM)下测定,内标法定量。实验结果表明,9种芳香胺在16 min内能够完全分离,且在各自的范围内线性关系良好,相关系数(R²)均大于0.998。9种芳香胺的检出限(LOD)和定量限(LOQ)分别为0.12～0.48μg/L和0.40～1.60μg/L。选取饮用水源地地表水、近海海水和典型印染行业废水3种类型水体进行加标回收试验,在2个加标水平(2.0、10.0μg/L)下,饮用水源地地表水的加标回收率为81.1%～109.8%,日内精密度为0.7%～5.2%,日间精密度为1.6%～6.2%;近海海水的加...     

固相萃取/超高效液相色谱-电喷雾串联质谱法检测酶制剂中3-硝基丙酸

采用高效液相色谱-电喷雾串联质谱对酶制剂中的3-硝基丙酸进行定性、定量分析。样品经乙腈提取,PSA固相萃取柱净化后,以Waters HSS T3柱(1.8μm,2.1 mm×100 mm)分离,乙腈和水为流动相,负离子模式扫描。结果表明,3-硝基丙酸在12.5～125μg/L范围内呈良好线性关系,相关系数大于0.993,定量下限为5.0μg/kg。在低、中、高3个加标水平下,3-硝基丙酸的回收率为69.1%～114.4%,相对标准偏差(RSD)为0.9%～8.9%。对酶制剂样品的测定表明该方法简便、快速,检测结果可靠。     

KBrO3氧化甲基紫褪色动力学光度法测定食品中痕量钒

基于0.004 mol/L的柠檬酸介质中,痕量V(Ⅴ)催化KBrO3氧化甲基紫的褪色反应,建立了测定痕量V(Ⅴ)的动力学光度法。方法的检出限为1.23μg/L,线性范围为0～0.16μg/mL。讨论了酸度、反应物浓度、温度、反应时间、干扰离子等因素的影响,确定了该体系反应的最佳条件。在25 mL溶液中,测定2.0μg V(Ⅴ)的RSD为1.9%(n=11)。方法可用于测定小麦和苹果中的痕量V(Ⅴ),RSD为1.1%～2.7%,标准加入回收率为97.6%～99.0%。     

邻-硝基酚分子印迹聚合物为涂层固相萃取搅拌棒的制备及其萃取性能研究

以邻-硝基酚为模板,甲基丙烯酸二甲胺乙酯和4-乙烯基吡啶为混合单体,利用整体材料"原位"聚合技术制备分子印迹聚合物为涂层的固相萃取搅拌棒(MIP-SBSE)。考察了制备条件对MIP-SBSE选择吸附性能的影响,并与高效液相色谱-二极管阵列检测器联用,探讨MIP-SBSE对环境水样中邻-硝基酚及其它酚类物质的选择萃取性能。考察了样品基底中离子强度、pH值以及吸附时间和解吸时间等萃取条件对目标化合物选择性能影响。结果表明,在最佳萃取条件下,MIP-SBSE对模板分子及其它酚类物质具有一定选择性能和较高的富集能力,对邻-硝基酚的线性范围为3.0～200μg/L;检出限LOD(S/N=3)为0.13μg/L;定量限LOQ(S/N=10)为0.40μg/L。在实际样品分析中,模板分子加标回收率为83.4%～120.9%;其它酚类物质的加标回收率在59.8%～129.0%之间。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.