Block copolymer micelle shuttles with tunable transfer temperatures between ionic liquids and aqueous solutions

Four poly((1,2-butadiene)- block-ethylene oxide) (PB-PEO) diblock copolymers were shown to self-assemble into micelles with PB cores and PEO coronas (including spheres, cylinders, and vesicles) in the ionic liquid, 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([EMIM][TFSI]). All four systems exhibited the "micelle shuttle" (He, Y.; Lodge, T. P. J. Am. Chem. Soc. 2006, 128, 12666-12667), whereby PB-PEO micelles transferred, reversibly and with preservation of micelle structure, from an aqueous phase at room temperature to a hydrophobic ionic liquid at high temperature. The micelle size (both mean and distribution) depends on whether it was initially dissolved in water or in the ionic liquid, but the initial micelle structures in the ionic liquid were shown by dynamic light scattering to be preserved during the transfer and persist essentially unchanged for months in both the ionic liquid and water. The transfer was shown to be driven by the deteriorating solvent quality of water for PEO at high temperature, while the ionic liquid remains a good solvent. The transfer temperature could be tuned by adding ionic or nonionic additives to the aqueous phase to change the solvent quality of water for PEO, and by using ionic liquids with different polarity.     

Nanoscale elastic modulus variation in loaded polymeric micelle reactors

Tapping mode atomic force microscopy (TM-AFM) enables mapping of chemical composition at the nanoscale by taking advantage of the variation in phase angle shift arising from an embedded second phase. We demonstrate that phase contrast can be attributed to the variation in elastic modulus during the imaging of zinc acetate (ZnAc)-loaded reverse polystyrene-block-poly(2-vinylpyridine) (PS-b-P2VP) diblock co-polymer micelles less than 100 nm in diameter. Three sample configurations were characterized: (i) a 31.6 μm thick polystyrene (PS) support film for eliminating the substrate contribution, (ii) an unfilled PS-b-P2VP micelle supported by the same PS film, and (iii) a ZnAc-loaded PS-b-P2VP micelle supported by the same PS film. Force-indentation (F-I) curves were measured over unloaded micelles on the PS film and over loaded micelles on the PS film, using standard tapping mode probes of three different spring constants, the same cantilevers used for imaging of the samples before and after loading. For calibration of the tip geometry, nanoindentation was performed on the bare PS film. The resulting elastic modulus values extracted by applying the Hertz model were 8.26 ± 3.43 GPa over the loaded micelles and 4.17 ± 1.65 GPa over the unloaded micelles, confirming that phase contrast images of a monolayer of loaded micelles represent maps of the nanoscale chemical and mechanical variation. By calibrating the tip geometry indirectly using a known soft material, we are able to use the same standard tapping mode cantilevers for both imaging and indentation.     

Reversed micelle formation in a model liquid-liquid extraction system

The formation of reversed micelles and the roles of extractant and extracted complexes were investigated in the Cyanex923/n-heptane/H(2)SO(4) system. Interfacial tension (gamma), electrical conductivity (kappa), and water content measurements showed that Cyanex923 had a tendency to self-assemble, forming reversed micelles. The changes in electrical conductivity with concentration of H(2)SO(4) in the organic phase (C(H2)SO(4), o) exhibited an S-type curve: a correlation was found between the change in electrical conductivity and the water content as a function of C(H2)SO(4), o. The changes of electrical conductivity were mainly induced by the components and microstructure in the organic phase, while the conversion of extracted complex also resulted in the changes of components and microstructure in the organic phase. Fourier transform infrared (FTIR) spectroscopy and dynamic light scattering (DLS) were used to characterize the organic phases and sizes of the reversed micelles, respectively. The extractant and extracted complexes, such as Cyanex923H(2)SO(4), were involved in the formation of reversed micelles.     

Two-step phase transition via in situ hydrolysis of thermosensitive polymeric micelles with acid-labile core

This communication reports thermoresponsive diblock copolymer micelles composed of a hydrophilic poly(ethylene glycol) (PEG) shell with temperature-responsive functionality and an acid-labile, hydrophobic poly(N-acryloyl-2,2-dimethyl-1,3-oxazolidine) (PADMO) core. Because of the partial in situ hydrolysis of these micelles, an interesting two-step phase transition occurs, exhibiting two separate cloud points. This can be attributed to the dual characters displayed by poly(2-hydroxyethyl acrylamide) (PHEAM), the hydrolysis product of PADMO in an acid medium. The formation of hydrogen bonding between PEG and PHEAM enhances the hydrophobicity of PEG chains and promotes the phase transition that takes place at a lower temperature than before. On the other hand, generation of water-soluble PHEAM increases the hydrophilicity of the whole micelles and requires higher temperature that induces dehydration of these micelles. This finding could help us better understand the relationship between micellar microstructure and thermosensitive behaviors.     

A novel approach to study the inclusion mechanism of imidazole derivatives in micellar chromatography

A chromatographic approach was proposed to describe the existence of surfactant micelles in a surfactant/hydroorganic phosphate buffer mobile phase. Using this mixture as a mobile phase, a novel mathematical theory is presented to describe the inclusion mechanism of imidazole derivatives in surfactant micelles. Using this model, enthalpy, entropy and the Gibbs free energy were determined for two chromatographic chemical processes: (i) the transfer of the imidazole derivative from the mobile phase to the stationary phase; and (ii) the imidazole derivative inclusion in surfactant micelles. These thermodynamic data indicate that the main parameter determining chromatographic retention is distribution of the imidazole derivatives to micelles of surfactant while the interaction with the stationary phase play a minor role.     

Enhanced solubilization of bovine serum albumin in reverse micelles by compressed CO2

The effect of compressed CO2 on the solubilization of bovine serum albumin (BSA) in water/sodium bis-(2-ethylhexyl) sulfosuccinate (AOT)/isooctane reverse micelles was studied by observing phase behavior and recording UV-visible spectra under different conditions. The pH values within the water cores of reverse micelles at different CO2 pressures were also determined. The solubilization capacity of the reverse micelles for the protein increased considerably as CO2 pressure increased within the low-pressure range, but decreased at higher CO2 pressures, so that the micelles eventually lost their ability to solubilize the protein. The effect of CO2 on the stability of the reverse micelles played an important role in the relationship between pressure and protein solubility. A "multicomplex" model was proposed to explain these effects. The different solublization capacities within different pressure ranges demonstrates the unique advantage of using compressed CO2 in the extraction of proteins with reverse micelles.     

Investigation of the chiral surfactant N-dodecoxycarbonylvaline in electrokinetic chromatography: improvements in elution range and pH stability via mixed micelles and vesicles, and the hydrophobicity determination of basic pharmaceutical drugs

The chiral surfactant dodecoxycarbonylvaline (DDCV) has proven to be an effective pseudostationary phase for the separation of many enantiomeric pharmaceutical compounds. In this study the elution range and the prediction of octanol-water partitioning for the DDCV micellar system was examined. Through incorporation of DDCV in mixed micelles and unilamellar vesicles, enhancement of the elution range was observed. The mixed micelles contained a second anionic surfactant, sodium dodecyl sulfate (SDS), while the vesicles were composed of DDCV and the cationic surfactant cetyltrimethylammonium bromide (CTAB). Enantioselectivity, as well as other chromatographic and electrophoretic parameters, were compared between the mixed micelles, vesicles, and DDCV micelles. The hydrophobicity of the DDCV system was also evaluated as a predictor of n-octanol-water partition coefficients for 15 beta amino alcohols. The correlation between the logarithm of the retention factor (log k) and log P(ow) for seven hydrophobic beta-blockers and eight beta-agonists were r2 = 0.964 and r2 = 0.814, respectively.     

Theory of surface micelles of semifluorinated alkanes

Surface structures of semifluorinated alkanes F(CF(2))(n)(CH(2))(m)H (referred to as FnHm) spread on the air/water interface are investigated theoretically. The study is focused on the disklike surface micelles that were recently identified by AFM and scattering techniques at sufficiently high surface concentrations. We show that (1) the micelles emerge as a result of liquid/liquid (rather than liquid/gas) phase separation in the Langmuir layer; (2) the micelles are islands of the higher-density phase with roughly vertical orientation of FnHm molecules (F-parts extend toward air, H-parts toward water) and the matrix is the lower density-phase where the FnHm diblocks are nearly parallel to the water surface; (3) the micelles and the hexagonal structure they form are stabilized by the electrostatic interactions which are mainly due to the vertical dipole moments of the CF(2)- CH(2) bonds in the vertical phase; and (4) the electrostatic repulsive interactions can serve to suppress the micelle size polydispersity.     

Morphology, crystalline structure and thermal properties of PEO/MEEP blends

Poly(ethylene oxide) and poly[bis[2-(2′-methoxyethoxy) ethoxy] phosphazene], PEO/MEEP, polymer blends were investigated by thermal analysis, X-ray diffraction, and atomic force microscopy. MEEP is an amorphous polymer and its semicrystalline blends with PEO showed two distinct glass transitions, whose composition dependence was analysed by the Lodge and McLeish self-concentration model. It appears that an amorphous miscible phase is present in these blends. Excess melting enthalpy was observed for blends with high MEEP concentration. PEO lamellar characteristics exhibited changes as a function of MEEP content, both in X-ray patterns and AFM images that indicated the intercalation of MEEP side chains in the lamellar crystalline structure.     

Phase behavior of a mixture of poly(isoprene)-poly(oxyethylene) diblock copolymer and poly(oxyethylene) surfactant in water

The phase behavior of a mixture of poly(isoprene)-poly(oxyethylene) diblock copolymer (PI-PEO or C250EO70) and poly(oxyethylene) surfactant (C12EO3, C12EO5, C12EO6, C12EO7, and C12EO9) in water was investigated by phase study, small-angle X-ray scattering, and dynamic light scattering (DLS). The copolymer is not soluble in surfactant micellar cubic (I1), hexagonal (H1), and lamellar (Lalpha) liquid crystals, whereas an isotropic copolymer fluid phase coexists with these liquid crystals. Although the PI-PEO is relatively lipophilic, it increases the cloud temperatures of C12EO3-9 aqueous solutions at a relatively high PI-PEO content in the mixture. Most probably, in the copolymer-rich region, PI-PEO and C12EOn form a spherical composite micelle in which surfactant molecules are located at the interface and the PI chains form an oil pool inside. In the C12EO5/ and C12EO6/PI-PEO systems, one kind of micelles is produced in the wide range of mixing fraction, although macroscopic phase separation was observed within a few days after the sample preparation. On the other hand, small surfactant micelles coexist with copolymer giant micelles in C12EO7/ and C12EO9/PI-PEO aqueous solutions in the surfactant-rich region. The micellar shape and size are calculated using simple geometrical relations and compared with DLS data. Consequently, a large PI-PEO molecule is not soluble in surfactant bilayers (Lalpha phase), infinitely long rod micelles (H1 phase), and spherical micelles (I1 phase or hydrophilic spherical micelles) as a result of the packing constraint of the large PI chain. However, the copolymer is soluble in surfactant rod micelles (C12EO5 and C12EO6) because a rod-sphere transition of the surfactant micelles takes place and the long PI chains are incorporated inside the large spherical micelles.     

Phase Behavior and Aggregate Structure in Aqueous Mixtures of Sodium Cholate and Glycerol Monooleate

The phase behavior of the glycerol monooleate (GMO)-sodium cholate-water (or 0.9 wt% NaCl) system has been examined in the solvent-rich part, using small-angle X-ray scattering and conventional methods. Addition of cholate up to 7% of the total amphiphile swells the cubic phase of the binary GMO-water system so that it takes up almost 70% of water in the salt-free case and 55% in salt. With more bile salt the lamellar phase also appears highly swollen (up to 85% in water, 75% in brine). In the salt solution a small isotropic L3-phase region replaces the lamellar phase at a solvent content of about 79%. The lamellar phase can accept only about 0.2 cholate molecule per GMO, in both water and brine, and a phase with globular micelles (L1) follows and dominates the diagram. No threadlike micelles appear in this system. Investigation of the particle structures with cryo-transmission electron microscopy (TEM) in dilute systems (99% solvent) show globular micelles and coexisting vesicles and globular micelles. In the presence of salt, dilution of the L3 phase results in dispersed globular particles with an irregular internal morphology that suggests they are a dispersed L3 phase. These particles coexist with faceted particles having an inner structure giving a hexagonal pattern in projection, suggested to derive from the cubic phase. The cubic phase in the salt-free systems did not give dispersions stable enough for cryo-TEM examination. Copyright 1999 Academic Press.     

The effect of the detergent cetyltrimethylammoniumchloride on the phase behaviour of dipalmitoylphosphatidylcholine: A high precision calorimetric study.

The influence of the linear, positively charged detergent cetyltrimethylammoniumchloride (CTAC1) on the well known phase behaviour of fully hydrated dipalmitoylphosphatidylcholine (DPPC) has been studied along fourteen isopleths of the phase diagram using high sensitivity scanning microcalorimetry. Particular interest was focused towards the effects of very small amounts of detergent down to the region of 1 CTAC1 per 10⁴ DPPC-molecules.Even starting with such low concentrations distinct changes of the thermograms are detectable by high sensitivity DSC. Essentially, the phase diagram is cut into four domains between the two limiting cases of pure phospholipid multilamellar dispersion and isotropic solution of detergent micelles, respectively. At the present stage these four regions in the phase diagram are identified as follows : 1. 0–1 Mol % CTAC1: a modified lamellar phase 2. 1–50 Mol % CTAC1: a two-phase region with this modified lamellar phase coexisting with a newly formed detergent-rich phase. 3. 50–90 Mol % CTAC1: large mixed micelles. 4. > 90 Mol % CTAC1: an isotropic solution of small mixed phospholipid/detergent micelles.     

Formation of Copper(II) Thiocyanato and Cadmium(II) Iodo Complexes in Micelles of Nonionic Surfactants with Varying Poly(ethylene oxide) Chain Lengths

Formation of copper(II) thiocyanato and cadminum(II) iodo complexes in micelles of poly(ethylene oxide) (PEO)-type nonionic surfactants with varying PEO chain lengths of 9.5 (Triton X-100), 30 (Triton X-305), and 40 (Triton X-405) has been studied by titration spectrophotometry and calorimetry at 298 K. In a given surfactant solution, all data obtained were analyzed by assuming formation of ternary complexes MX(n)Y(m)((2-n)+) (M = Cu(II),Cd(II); X = SCN(-), I(-); Y = surfactant), and the complexes thus form in aqueous phase (m = 0) or in micelles (m = 1). In the Cu(II)-SCN(-) system, spectrophotometric data obtained by varying concentrations of the surfactant can be explained well in terms of formation of Cu(NCS)(2)Y in micelles and Cu(NCS)(+) and Cu(NCS)(2) in an aqueous phase, and it turned out that formation constant of Cu(NCS)(2)Y increases with increasing PEO chain length. In the Cd(II)-I(-) system, the formation of CdI(3)Y(-) and CdI(4)Y(2-) is concluded in micelles, and that of CdI(+), CdI(3)(-), and CdI(4)(2-) in an aqueous phase. Interestingly, formation enthalpies of CdI(3)Y(-) and CdI(4)Y(2-) become significantly less negative with increasing PEO chain length. This suggests that transfer of the complexes from aqueous solution to a hydrophobic octylphenyl (OP) moiety in micelles is significantly more exothermic than that to a hydrophilic PEO one. Thermodynamic parameters of transfer of CdI(3)(-) and CdI(4)(2-) from aqueous solution to the OP and PEO moieties of micelles have been evaluated. Copyright 2000 Academic Press.     

Reverse micelles: inert nano-reactors or physico-chemically active guides of the capped reactions

Reverse micelles present self-assembled multi-molecular entities formed within specific compositional ranges of water-in-oil microemulsions. The structure of a reverse micelle is typically represented as nano-sized droplet of a polar liquid phase, capped by a monolayer of surfactant molecules, and uniformly distributed within a non-polar, oil phase. Although their role in serving as primitive membranes for encapsulation of primordial self-replicating chemical cycles that anticipated the very origins of life has been proposed, their first application for 'parent(hesis)ing' chemical reactions with an aim to produce 'templated' 2D arrays of nanoparticles dates back to only 25 years ago. Reverse micelles have since then been depicted as passive nano-reactors that via their shapes template the growing crystalline nuclei into narrowly dispersed or even perfectly uniform nano-sized particles. Despite this, numerous examples can be supported, where from deviations from the simple unilateral correlations between size and shape distribution of reverse micelles and the particles formed within may be reasonably implied. A rather richer, dynamical role of reverse micelles, with potential significance in the research and design of complex, self-assembly synthesis pathways, as well as possible adoption of their application as an aspect of biomimetic approach, is suggested herein.     

Temperature- and pH-responsive unimolecular micelles with a hydrophobic hyperbranched core

The dendritic unimolecular polymeric micelles with a hydrophobic dendritic polyester (Boltorn H40) as the core and the grafted biocompatible poly(N, N-diethylacrylamide)-b-poly(2-(dimethylamino)ethyl methacrylate) (PDEAAM-b-PDMAEMA) as the shell were synthesized by successive reversible addition–fragmentation transfer (RAFT) polymerization of N, N-diethylacrylamide (DEAAM) and 2-(dimethylamino)ethyl methacrylate (DMAEMA) monomers. Laser light scattering studies indicated that the resulting unimolecular polymeric micelles H40–PDEAAM–PDMAEMA with double stimuli-responsive shells exhibited a reversible two-stage phase transition behavior. The effect of varying the block length of PDMAEMA on the thermosensitivity of unimolecular polymeric micelles was studied. With an increase in the outer corona length of PDMAEMA, the temperature range of phase transition for the inner shell PDEAAM would become broad. As pH decreased to 2, the high hydrophilic PDMAEMA blocks with high protonation were independent of temperature, and the size of unimolecular polymeric micelles increased due to the extended-chain conformation of outer layer. The internal core cavities of the unimolecular polymeric micelles exhibited a great potential of loading guest molecules according to the analysis of pyrene probe fluorescence spectra.     

Structural evolution in the isotropic channel of a water-nonionic surfactant system that has a disconnected lamellar phase: a 1H NMR self-diffusion study

We showed in a previous study that a water-nonionic surfactant system, where the surfactant is a 9:1 mixture of tetraethylene glycol monodecyl ether (C(10)E(4)) and pentaethylene glycol monodecyl ether (C(10)E(5)), forms a disconnected lamellar (L(α)) phase. Thus, the isotropic phase spans the whole concentration range from the water-rich L(1) region to the surfactant-rich L(2) region of the phase diagram. The L(1) and L(2) regions are connected via an isotropic channel that separates the two regions of the L(α) phase. In this letter, we monitored the structural evolution of the isotropic phase along a path through this isotropic channel via (1)H NMR self-diffusion measurements. We used this technique because it enables us to distinguish between discrete and bicontinuous structures by comparing the relative self-diffusion coefficients (obstruction factors) D/D(0) of the solvents (i.e. of water and surfactant in the present case). We found that the obstruction factor of water decreases whereas the obstruction factor of the surfactant increases with increasing surfactant concentration and increasing temperature. This trend is interpreted as the transition from a water-continuous L(1) region, which contains discrete micelles, to a bicontinuous structure, which may extend to very high surfactant concentrations. Although there is good evidence of bicontinuity over a broad concentration range, there is no evidence of inverse micelles or any other microstructure at the highest concentration studied in the surfactant-rich L(2) phase.     

Phase behavior of cetyltrimethylammonium surfactants with oligo carboxylate counterions mixed with water and decanol: attraction between charged planes or spheres with oligomeric counterions

Cetyltrimethylammonium surfactants with a range of oligo carboxylate anions bearing 2, 3, or 4 negative charges have been synthesized, and their respective behaviors in binary mixtures with water and in ternary mixtures with added decanol have been investigated. In binary mixtures with water, all surfactants formed nearly spherical micelles at high water contents; however, the interactions between micelles varied strongly with the number of charges in the counterion. Micelles with divalent counterions were generally miscible with water, whereas micelles with tri- or tetravalent counterions demixed in one concentrated and one dilute phase. Addition of decanol resulted in all cases in the appearance of a lamellar phase, and all investigated oligo carboxylate anions (di-, tri-, and tetravalent) gave rise to a strong attraction between the lamellar planes, resulting in a limited swelling (up to 35-40 wt % water) of the lamellar phase in contact with excess water. These experiments confirm the theoretically predicted influence of aggregate geometry (spheres or planes) on the attraction between colloidal aggregates neutralized by multivalent counterions. Further addition of decanol resulted in the appearance of a second birefringent phase in equilibrium with the lamellar phase. SWAXS showed this phase to be lamellar and to display short-range order that disappeared upon heating. This phase is identified as a lamellar gel phase (Lbeta-phase).     

Coexistence of two kinds of fluorinated hydrogenated micelles as building blocks for the design of bimodal mesoporous silica with two ordered mesopore networks

A simple and effective route has been developed for the synthesis of bimodal (3.6 and 9.4 nm) mesoporous silica materials that have two ordered interconnected pore networks. Mesostructures have been prepared through the self-assembly mechanism by using a mixture of polyoxyethylene fluoroalkyl ether and triblock copolymer as building blocks. The investigation of the R(F)(8)(EO)(9)/P123/water phase diagram shows that in the considered surfactant range of concentrations the system is micellar (L(1)). DLS measurements indicate that this micellar phase is composed of two types of micelles; the size of the first one at around 7.6 nm corresponds unambiguously to the pure fluorinated micelles. The second type of micelles at higher diameter consists of fluorinated micelles that have accommodated a weak fraction of P123 molecules. Thus, in this study the bimodal mesoporous silica is really templated by two kinds of micelles.     

Characterization of the initial stages of SBA-15 synthesis by in situ time-resolved small-angle X-ray scattering

The initial stages of SBA-15 synthesis have been studied by using in situ time-resolved small-angle X-ray scattering with a synchrotron radiation source. The quantitative analysis of X-ray scattering and diffraction intensities allows the structures of intermediates to be identified at the different stages of SBA-15 synthesis. Following tetraethylorthosilicate (TEOS) addition, an intense small-angle scattering and an associated secondary maximum are observed, which are attributed to non-interacting surfactant template micelles encrusted with silicate species. After 25-30 min of the reaction, the broad scattering disappears and narrow Bragg diffraction peaks typical of hexagonally ordered structure are observed. The cylindrical micelles identified from X-ray scattering data appear to be the direct precursors of 2D hexagonal SBA-15 structure. Just after the formation of the SBA-15 hexagonal phase, the cylindrical micelles are only weakly linked in the hexagonal structure. As the synthesis proceeds, the solvent in the void volume between the cylindrical micelles is gradually replaced by more dense silicate species. The unit cell parameter of SBA-15 is progressively decreasing during the SBA-15 synthesis, which can be related to the condensation and densification of silicate fragments in the spaces between the cylinders. The volume fraction of the 2D hexagonally ordered phase is sharply growing during the first 2 h of the reaction. The inner core radius of SBA-15 material remains almost constant during the whole synthesis and is principally affected by the size of the poly(propylene oxide) inner core in the original cylindrical micelles.     

Physicochemical characterization of degradable thermosensitive polymeric micelles

Amphiphilic AB block copolymers consisting of thermosensitive poly(N-(2-hydroxypropyl) methacrylamide lactate) and poly(ethylene glycol), pHPMAmDL-b-PEG, were synthesized via a macroinitiator route. Dynamic light scattering measurements showed that these block copolymers form polymeric micelles in water with a size of around 50 nm by heating of an aqueous polymer solution from below to above the critical micelle temperature (cmt). The critical micelle concentration as well as the cmt decreased with increasing pHPMAmDL block lengths, which can be attributed to the greater hydrophobicity of the thermosensitive block with increasing molecular weight. Cryogenic transmission electron microscopy analysis revealed that the micelles have a spherical shape with a narrow size distribution. 1H NMR measurements in D2O showed that the intensity of the peaks of the protons from the pHPMAmDL block significantly decreased above the cmt, indicating that the thermosensitive blocks indeed form the solidlike core of the micelles. Static light scattering measurements demonstrated that pHPMAmDL-b-PEG micelles with relatively large pHPMAmDL blocks possess a highly packed core that is stabilized by a dense layer of swollen PEG chains. FT-IR analysis indicated that dehydration of amide bonds in the pHPMAmDL block occurs when the polymer dissolved in water is heated from below to above its cmt. The micelles were stable when an aqueous solution of micelles was incubated at 37 degrees C and at pH 5.0, where the hydrolysis rate of lactate side groups is minimized. On the other hand, at pH 9.0, where hydrolysis of the lactic acid side groups occurs, the micelles started to swell after 1.5 h of incubation and complete dissolution of micelles was observed after 4 h as a result of hydrophilization of the thermosensitive block. Fluorescence spectroscopy measurements with pyrene loaded in the hydrophobic core of the micelles showed that when these micelles were incubated at pH 8.6 and at 37 degrees C the microenvironment of pyrene became increasingly hydrated in time during this swelling phase. The results demonstrate the potential applicability of pHPMAmDL-b-PEG block copolymer micelles for the controlled delivery of hydrophobic drugs.