Preparation of Nanosize Tin Oxide Particles from Water-in-Oil Microemulsions

Nanoparticles of tin oxide (SnO2) have been prepared from water-in-oil microemulsions consisting of water, AOT (surfactant), and n-heptane (oil). Precursor hydroxides were precipitated in the aqueous cores of water-in-oil microemulsions and then calcined at 600 degrees C for 2 h to form tin oxide powder. The formation of phase pure tin oxide was confirmed by means of X-ray diffraction analysis. The tin oxide powder was found to be less than 40 nm in particle diameter and to have a higher specific surface area, about 73 m2/g, when compared with tin oxide powder prepared through the conventional precipitation method (19 m2/g). Copyright 1999 Academic Press.     

Mechanism for the formation of tin oxide nanoparticles and nanowires inside the mesopores of SBA-15

The formation of polycrystalline tin oxide nanoparticles (NP) and nanowires was investigated using nanocasting approach included solid-liquid strategy for insertion of SnCl₂ precursor and SBA-15 silica as a hard template. HR-TEM and XRD revealed that during the thermal treatment in air 5 nm tin oxide NP with well defined Cassiterite structure were formed inside the SBA-15 matrix mesopores at 250 °C. After air calcination at 700 °C the NP assembled inside the SBA-15 mesopores as polycrystalline nanorods with different orientation of atomic layers in jointed nanocrystals. It was found that the structure silanols of silica matrix play a vital role in creating the tin oxide NP at low temperature. The pure tin chloride heated in air at 250 °C did not react with oxygen to yield tin oxide. Tin oxide NP were also formed during the thermal treatment of the tin chloride loaded SBA-15 in helium atmosphere at 250 °C. Hence, it is well evident that silanols present in the silica matrix not only increase the wetting of tin chloride over the surface of SBA-15 favoring its penetration to the matrix pores, but also react with hydrated tin chloride according to the proposed scheme to give tin oxide inside the mesopores. It was confirmed by XRD, N₂-adsorption, TGA-DSC and FTIR spectra. This phenomenon was further corroborated by detecting the inhibition of SnO₂ NP formation at 250 °C after inserting the tin precursor to SBA-15 with reduced silanols concentration partially grafted with tin chloride.     

Praseodymium hydroxide and oxide nanorods and Au/Pr6O11 nanorod catalysts for CO oxidation

Praseodymium hydroxide nanorods were synthesized by a two-step approach: First, metallic praseodymium was used to form praseodymium chloride, which reacted subsequently with KOH solution to produce praseodymium hydroxide. In the second step the hydroxide was treated with a concentrated alkaline solution at 180 degrees C for 45 h, yielding nanorods as shown by the scanning and transmission electron microscopy images. The results of X-ray diffraction and energy-dispersive X-ray spectroscopy experiments indicate that these nanorods are pure praseodymium hydroxide with a hexagonal structure, which can be converted into praseodymium oxide (Pr6O11) nanorods of a face-centered cubic structure after calcination at 600 degrees C for 2 h in air. Gold was loaded on the praseodymium oxide nanorods using HAuCl4 as the gold source, and NaBH4 was used to reduce the gold species to metallic nanoparticles with sizes of 8-12 nm on the nanorod surface. These Au/Pr6O11 nanorods exhibit superior catalytic activity for CO oxidation.     

A Novel Method for Making NiO Nanofibres via An Electrospinning Technique

Thin PVA/nickel acetate composite fibres were prepared by using sol-gel processing and electrospinning technique. After calcination of the above precursor fibres, NiO nanofibres with a diameter of 50-150nm could be successfully obtained. The fibres were characterized by SEM,FT-IR, WAXD, respectively.     

An electron microscopy investigation of tin-molybdenum oxides

Tin-molybdenum oxides prepared by the calcination of precipitates at high temperatures have been investigated by electron microscopy. The solids, which adopt the rutile-related tin(IV) oxide-type structure, are composed of crystalline particles containing planar defects, some of which have been characterized as twin boundaries. Although molybdenum has been found to be concentrated at these planar faults the examination of pure tin(IV) oxide prepared by similar methods shows that their formation is not dependent on the presence of molybdenum. It is suggested that molybdenum segregates to the twin boundaries during the calcination process to accommodate itself in more favorable coordination.     

Nanofibers of LiMn2O4 by electrospinning

Through sol-gel processing and electrospinning technique, extrathin fibers of poly(vinyl alcohol) (PVA)/lithium chloride/manganese acetate composite fibers were prepared. After calcination of the above precursor fibers at 600 degrees C, the spinel lithium manganese oxide (LiMn2O4) nanofibers, with a diameter of 100-200 nm, were successfully obtained. The fibers were investigated by TG-DTA, XRD, FT-IR, and SEM, respectively. The results showed that the crystalline phase and morphology of the fibers were largely influenced by the calcination temperature.     

Preparation of Mn3O4 Nanofibres via An Electrospinning Technique

Thin PVA/manganese acetate composite fibres were prepared by using sol-gel processing and electrospinning technique.After calcinations of the above precursor fibres,Mn3O4 nanofibres with a diameter of 50-200 nm could be successfully obtained.The fibres were characterized by SEM,FT-IR,XRD.The results showed that the crystalline phase and morphology of nanofibres were largely influenced by the calcination temperature.     

静电纺丝法制备NiO纳米纤维及其表征

纳米级NiO因具有优良的催化和热敏等性能而被广泛用于催化剂^[1]、电池电极^[2,3]、光电转化材料^[4～6]、电化学电容器^[7～8]等诸多方面.迄今,已成功地制备出N iO的纳米颗粒^[9]、纳米线^[10]及纳米薄膜^[11],但是对于具有准一维结构的NiO纳米纤维的制备及性能研究尚未见报道.     

Investigations of the tin-antimony-oxygen system by high-resolution electron microscopy

A range of tin-antimony oxides, prepared by the calcination of precipitates, were examined by high-resolution electron microscopy. Products formed at 600°C contain small crystals of a rutile-type material and, depending on antimony concentration, varying amounts of disordered and/or amorphous phases. The observations are consistent with a resistivity to bulk phase equilibrium under conditions of low temperature and high antimony concentrations. Heating of the tin-antimony oxides to 1000°C for prolonged periods is accompanied by an increase in the crystallinity and particle size of the rutile-type material as a result of the thermally induced aggregation of tin(IV) oxide units. The observations are consistent with limited antimony incorporation in the bulk tin(IV) oxide lattice and a migration of antimony to surface sites. There was no evidence for any discrete, readily identifiable, antimony oxide phases, although a nonrutile-type material was observed at higher antimony concentration. The rutile-type phases often contained planar faults which were identified in some instances as twin boundaries; the possibility that these might provide a means of accommodating antimony within the tin oxide lattice is briefly considered. The relationship between our observations and the information available from other techniques is discussed.     

Synthesis, structure, texture, and CO sensing behavior of nanocrystalline tin oxide doped with scandia

Weakly agglomerated nanocrystalline scandia doped tin oxide powders with high surface area (170-220 m(2)/g) and uniform size (3-4 nm) were synthesized for the first time by a two-step hydrothermal process in the presence of urea, followed by the calcination between 500 and 1200 degrees C. The structure and texture of the binary oxide system were characterized by thermogravimetry and differential thermal analysis, Brunauer-Emmett-Teller-specific surface area analysis, transmission electron microscopy, X-ray diffraction, Raman spectroscopy, and X-ray photoelectron spectroscopy. A metastable scandium tin oxide solid solution in tetragonal structure was formed for the scandia content lower than 6 mol % as the samples were calcined at 800 degrees C, and the excess Sc atoms were dispersed at the surface of the crystallites above this limit. The solid solution was metastable, so scandium migrated toward the surface region of the crystallites and produced a second phase of Sc(4)Sn(3)O(12) during calcining at high temperatures over 1000-1200 degrees C. In the case of the samples with higher dopant concentration (>15 mol %), the calcination at the temperature between 500 and 800 degrees C caused the precipitation of Sc(2)O(3), and the calcination over 1000-1200 degrees C led to the formation of more Sc(4)Sn(3)O(12). Textural analysis showed that doping an appropriate amount of Sc(2)O(3) into nanosized SnO(2) could effectively inhibit the grain growth and stabilize the surface area against high-temperature calcinations below 1000 degrees C. CO gas-sensing property measurements revealed that the dispersion of Sc at the surfaces of the SnO(2) nanocrystallites could improve the CO sensitivity significantly, and the pellet sample with scandia content of 10 mol % sintered at 800 degrees C showed the best CO gas-sensing property in the operation temperature range of 300-400 degrees C. On the basis of the structural and textural analysis, the correlation between the structure/texture and the sensitivity to CO for the as-calcined (SnO(2))(1-x)(Sc(2)O(3))(x) nanocrystallites has been established and explained.     

Electrical and optical properties of ceramic–polymer nanocomposite coatings

Transparent, conductive composite coatings were fabricated from suspensions of poly(vinyl acetate‐acrylic) (PVAc‐co‐acrylic) copolymer latices (50–600 nm) and nanosized antimony‐doped tin oxide (ATO) particles (～15 nm). The suspensions were deposited as coatings onto poly(ethylene terephthalate) substrates and dried at 50 °C. Microstructure studies using field emission scanning electron microscopy and tapping‐mode atomic force microscopy (TMAFM) indicated that the latex particles coalesced during drying and forced the ATO particles to segregate into the boundaries between the latex particles. Low phase contrast was observed with TMAFM; this result was consistent with the presence of PVAc‐co‐acrylic in the ATO‐rich phase of the composite. The conductivity of the composite coatings followed a percolation power‐law equation, with the percolation threshold between 0.05 and 0.075 volume fractions of ATO and the critical conductivity exponent ranging from 1.34 to 2.32. The highest direct‐current conductivity of the composite coatings was around 10^?2 S/cm. The optical transmittance and scattering behavior of the coatings were also investigated. Compared with the PVAc‐co‐acrylic coating, the composite coatings had lower transparency because of the Rayleigh scattering. The transparency of the composite coatings was improved by a reduction in the coating thickness. The best transparency for the coatings with a direct‐current conductivity of approximately 10^?2 S/cm was around 85% at a wavelength of 600 nm. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1744–1761, 2003     

Direct formation of thermally stabilized amorphous mesoporous Fe2O3/SiO2 nanocomposites by hydrolysis of aqueous iron III nitrate in sols of spherical silica particles

Nanocomposite materials containing 10% and 20% iron oxide/silica, Fe2O3/SiO2 (w/w), were prepared by direct hydrolysis of aqueous iron III nitrate solution in sols of freshly prepared spherical silica particles (St?ber particles) present in their mother liquors. This was followed by aging, drying, calcination up to 600 degrees C through two different ramp rates, and then isothermal calcinations at 600 degrees C for 3 h. The calcined and the uncalcined (dried at 120 degrees C) composites were characterized by thermogravimetric analysis, differential scanning calorimetry, Fourier transform infrared spectroscopy, X-ray diffraction (XRD), N2 adsorption/desorption techniques, and scanning electron microscopy as required. XRD patterns of the calcined composites showed no line broadening at any d-spacing positions of iron oxide phases, thereby reflecting the amorphous nature of Fe2O3 in the composite. The calcined composites showed nitrogen adsorption isotherms characterizing type IV isotherms with high surface area. Moreover, surface area increased with the increasing of the iron oxide ratio and lowering of the calcination ramp rate. Results indicated that iron oxide particles were dispersed on the exterior of silica particles as isolated and/or aggregated nanoparticles. The formation of the title composite was discussed in terms of the hydrolysis and condensation mechanisms of the inorganic FeIII precursor in the silica sols. Thereby, fast nucleation and limited growth of hydrous iron oxide led to the formation of nanoparticles that spread interactively on the hydroxylated surface of spherical silica particles. Therefore, a nanostructured composite of amorphous nanoparticles of iron oxide (as a shell) spreading on the surface of silica particles (as a core) was formed. This morphology limited the aggregation of Fe2O3 nanoparticles, prevented silica particle coalescence at high temperatures, and enhanced thermal stability.     

Synthesis and characterization of ZnO nanowires by thermal oxidation of Zn thin films at various temperatures

In this research high-quality zinc oxide (ZnO) nanowires have been synthesized by thermal oxidation of metallic Zn thin films. Metallic Zn films with thicknesses of 250 nm have been deposited on a glass substrate by the PVD technique. The deposited zinc thin films were oxidized in air at various temperatures ranging between 450 °C to 650 °C. Surface morphology, structural and optical properties of the ZnO nanowires were examined by scanning electron microscope (SEM), X-ray diffraction (XRD), energy dispersive X-ray (EDX) and photoluminescence (PL) measurements. XRD analysis demonstrated that the ZnO nanowires has a wurtzite structure with orientation of (002), and the nanowires prepared at 600 °C has a better crystalline quality than samples prepared at other temperatures. SEM results indicate that by increasing the oxidation temperature, the dimensions of the ZnO nanowires increase. The optimum temperature for synthesizing high density, ZnO nanowires was determined to be 600 °C. EDX results revealed that only Zn and O are present in the samples, indicating a pure ZnO composition. The PL spectra of as-synthesized nanowires exhibited a strong UV emission and a relatively weak green emission.     

Preparation and Ethanol Sensing Properties of ZnO Nanofibers

ZnO nanofibers with an average diameter of about 90 nm were prepared by an electrospinning method combined with a calcination process. The as-electrospun nanofibers before and after calcination were characterized by means of differential thermal analysis(DTA), thermal gravimetric analysis(TGA), X-ray diffraction(XRD) and scanning electron microscopy(SEM). The fibers after calcination at 600 °C belong to the hexagonal wurtzite structure. The sensor based on ZnO nanofibers exhibited excellent ethanol sensing properties at 206 °C such as good linear dependence in the low concentration(1―100 μL/L), high response, and good selectivity. Fast response(less than 2 s) and recovery(about 16 s) were also observed in our investigations.     

Effect of synthesis methods on the morphology of nanosized tin dioxide particles

The effect of precursors on the microstructure of nanocrystalline tin dioxide is studied by thermal analysis, IR spectroscopy, electron microscopy, and X-ray powder diffraction. The precursor precipitated in an optimal pH range whose dehydration and crystallization occur over a wide temperature range with low degrees of oxolation yields crystalline tin dioxide with grain sizes on the order of 16 nm upon calcination at 800°C for 2 h.     

Surfactant mediated synthesis of spherical binary oxides photocatalytic with enhanced activity in visible light

Spherical silica and zirconia mixed titania and pure titania samples were prepared in presence of cetyltrimethylammonium bromide (CTAB) through controlled hydrolysis of corresponding metal alcoxides. Effect of surfactant amount and calcinations temperature on morphology, surface area and photocatalytic activity is studied using PXRD, SEM, FTIR, Solid state UV-vis spectroscopy and BET surface area. It is well observed that in presence of 2 mol% CTAB, uniform sized spherical oxide particles can be synthesized. However, increasing or decreasing the surfactant amount does not favor the spherical particle formation. Material synthesis in presence of CTAB not only helps in the spherical particle formation but also increases the surface area and visible light absorption. Studies on photocatalytic lead removal with respect to calcination temperature indicate that the calcination at 500 degrees C is most suitable for the best photocatalytic activity. Mixing of zirconia and silica helps in anatase phase stabilization even at 900 degrees C calcination. Accordingly low decrease in surface area even at 900 degrees C calcination is observed. Due to the phase stabilization and higher surface area binary oxide materials showed comparatively better photocatalytic activity even after calcination at 900 degrees C. So it can be concluded that present synthesis approach can produce uniform sized spherical binary oxide materials with better photocatalytic activity in visible light.     

Fabrication and characterization of polycrystalline WO3 nanofibers and their application for ammonia sensing

We describe the fabrication and characterization of tungsten oxide nanofibers using the electrospinning technique and sol-gel chemistry. Tungsten isopropoxide sol-gel precursor was incorporated into poly(vinyl acetate)(PVAc)/DMF solutions and electrospun to form composite nanofibers. The as-spun composite nanofibers were subsequently calcinated to obtain pure tungsten oxide nanofibers with controllable diameters of around 100 nm. SEM and TEM were utilized to investigate the structure and morphology of tungsten oxide nanofibers before and after calcination. The relationship between solution concentration and ceramic nanofiber morphology has been studied. A synchrotron-based in situ XRD method was employed to study the dynamic structure evolution of the tungsten oxide nanofibers during the calcination process. It has been shown that the as-prepared tungsten oxide ceramic nanofibers have a quick response to ammonia with various concentrations, suggesting potential applications of the electrospun tungsten oxide nanofibers as a sensor material for gas detection.     

Synthesis and photoluminescence of titania nanoparticle arrays templated by block-copolymer thin films.

High-density arrays of titania nanoparticles were prepared using a polystyrene-b-poly(ethylene oxide) block copolymer (PS-b-PEO) as a template and a titanium tetraisopropoxide based sol-gel precursor as titania source via a spin-coating method. The hydrophilic titania sol-gel precursor was selectively incorporated into hydrophilic PEO domains of PS-b-PEO and form titania nanoparticle arrays, due to a microphase separation between the PS block and the sol-gel/PEO phase. Field emission scanning electron microscopy (FESEM) and scanning probe microscopy (SPM) images showed that the uniformity and long-range order of the titania/PEO domains improved with increasing sol-gel precursor amount. Grazing incidence small-angle X-ray scattering (GISAXS) results indicate that the ordered structures exist over large length scales. Titania nanocrystal arrays of anatase modification were obtained by calcination at 600 degrees C for 4 h. After calcination, separated particles were observed for low and medium amounts of sol-gel precursors. Films with higher precursor amounts showed wormlike structures due to the aggregation between neighboring particles. Removal of the polymer matrix via UV treatment leads to highly ordered arrays of amorphous titania while retaining the domain size and interparticle distance initially present in the hybrid films. Photoluminescence (PL) properties were investigated for samples before and after calcination. The PL intensity increases with the increasing amount of sol-gel precursor. Bands at 412 nm were ascribed to self-trapped exitons and bands at 461 and 502 nm to oxygen vacancies, respectively. Uncalcined or UV-treated samples also showed PL properties similar to calcined samples, indicating that the local environment of the titanium atoms is similar to the environment of the crystalline anatase modification.     

Systematic synthesis and characterization of single-crystal lanthanide orthophosphate nanowires

A simple hydrothermal method has been developed for the systematic synthesis of lanthanide orthophosphate crystals with different crystalline phases and morphologies. It has been shown that pure LnPO(4) compounds change structure with decreasing Ln ionic radius: i.e., the orthophosphates from Ho to Lu as well as Y exist only in the tetragonal zircon (xenotime) structure, while the orthophosphates from La to Dy exist in the hexagonal structure under hydrothermal treatment. The obtained hexagonal structured lanthanide orthophosphate LnPO(4) (Ln = La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, and Dy) products have a wirelike morphology. In contrast, tetragonal LnPO(4) (Ln = Ho, Er, Tm, Yb, Lu, Y) samples prepared under the same experimental conditions consist of nanoparticles. The obtained hexagonal LnPO(4) (Ln = La --> Tb) can convert to the monoclinic monazite structured products, and their morphologies remained the same after calcination at 900 degrees C in air (Hexagonal DyPO(4) is an exceptional case, it transformed to tetragonal DyPO(4) by calcination), while the tetragonal structure for (Ho--> Lu, Y)PO(4) remains unchanged by calcination. The resulting LnPO(4) (Ln = La --> Dy) products consist almost entirely of nanowires/nanorods with diameters of 5-120 nm and lengths ranging from several hundreds of nanometers to several micrometers. Europium doped LaPO(4) nanowires were also prepared, and their photoluminescent properties were reported. The optical absorption spectrum of CePO(4) nanowires was measured and showed some differences from that of bulk CePO(4) materials. The possible growth mechanism of lanthanide phosphate nanowires was explored in detail. X-ray diffraction, field-emission scanning electron microscopy, transmission electron microscopy, electron diffraction, infrared absorption spectra, X-ray photoelectron spectroscopy, optical absorption spectra, and photoluminescence spectra have been employed to characterize these materials.     

Preparation of nanometer-sized In2O3 particles by a reverse microemulsion method

Nanometer-sized indium oxide (In(2)O(3)) particles have been prepared by chemical reaction of inorganic indium compounds and ammonia gas in a reverse microemulsion system consisting of water, Triton X-100 (surfactant), n-heptanol (co-surfactant), and n-octane (oil). Precursor hydroxides precipitated in the droplets of water-in-oil (W/O) microemulsion were calcined at different temperatures to form indium oxide powder. The factors affecting the particle size have been discussed; the calcination temperature is considered to be the important factor for controlling the size. In(2)O(3) calcined at 400 degrees C had a spherical form and a narrow size distribution. Calcination at 800 degrees C led to the formation of particles not only of irregular shape, but also of a wide size distribution. With the increase in calcination temperature from 400 to 800 degrees C, the average size of the particles grew from 7 to about 40 nm. The species of reactants used in the aqueous phase had a significant effect on the size of the particles. The average diameter of In(2)O(3) particles derived from reactant InCl(3) was 7 nm; that of particles derived from In(NO(3))(3) was 15 nm. The In(2)O(3) nanoparticles were characterized by transmission electron microscopy and X-ray diffraction. The phase behavior of the microemulsions is discussed.