Ce0.63Zr0.37MnxO2复合氧化物在CH4选择性催化还原NO反应中的研究

以Ce0.63Zr0.37MnxO2复合氧化物(OSM)为载体,Pt为活性组分,制备Pt质量百分含量为1%的催化剂。考察了OSM中Mn含量对CH4催化还原NO反应的性能,并利用XRD和H2-TPR对催化剂进行了表征。结果表明Pt/OSM催化剂在有氧条件下对CH4催化还原NO具有较好的催化活性,Mn含量为10%和15%的OSM制备的催化剂活性最好。XRD结果表明,Ce0.63Zr0.37MnxO2复合氧化物以固熔体形式存在,且Pt高度分散于载体上。H2-TPR结果表明,Pt/OSM2和Pt/OSM3催化剂具有较强的可还原性能,而Pt/OSM1和Pt/OSM4催化剂的可还原性能较弱。     

Pt/γ-AlOOH纳米棒复合催化材料的制备与性能

水热法制备了γ-AlOOH纳米棒,再以此纳米棒为载体,通过浸渍-NaBH4还原法制备了Pt/γ-AlOOH催化剂,考察了Pt/γ-AlOOH室温催化氧化甲醛的性能及Pt负载量对催化性能的影响。通过XRD,XPS,TEM和N2吸附-脱附测试等手段对所制备的样品进行表征。研究结果表明:Pt/γ-AlOOH催化剂比Pt/γ-Al2O_3具有更高的催化活性,主要是由于前者表面具有丰富的羟基基团和高分散Pt纳米颗粒。Pt/γ-AlOOH催化剂的活性先随Pt含量(0.05%~0.5%(w/w))的增加而增加,最后基本保持不变。从催化活性和成本两方面考虑,0.2%(w/w)Pt为最佳负载量。     

稀土尾矿基整体催化剂的制备及其低浓度甲烷催化燃烧性能

以稀土尾矿泡沫陶瓷(Tailings foam ceramics,简称TFC)为载体,采用拟薄水铝石制备铝溶胶,经过泡沫陶瓷载体表面涂覆铝溶胶和Cu溶液浸渍得到CuO/γ-Al₂O₃/TFC整体式催化剂,并利用SEM,XRD,XPS,H₂-TPR等技术对催化剂进行表征,评价其甲烷催化燃烧反应性能。结果表明,与原泡沫陶瓷相比,负载CuO的样品催化活性明显增强;随着CuO的负载量增加,催化性能呈现先升高后降低的趋势,CuO的负载量达到4%时催化活性最佳,甲烷转化率为10%和90%时的反应温度分别为301和581℃。CuO的负载量达到6%时,催化剂的活性中心由分散态CuO转变为晶相CuO,导致CuO在载体表面分散度降低并且利用率下降,催化活性降低。负载到泡沫陶瓷载体上的CuO形貌呈球形,整体催化剂活性组分中所有催化剂铈以Ce³⁺,Ce⁴⁺形态共存,铜以Cu²⁺和Cu~+形态共存,各金属元素间变价表明催化剂有较高的氧化还原能力,催化剂表面发生反应：Cu^2...     

碳纳米管负载铂催化剂的制备、结构及电化学加氢特性

采用浸渍沉淀法制备Pt/CNTs和Pt/C催化剂,并对其结构及电催化性能进行比较,表征.实验表明,以碳纳米管作催化剂载体可使催化剂的负载量,载体上铂的分散度以及其活性中心大大提高.与Pt/C(JohnsonMatthey)催化剂相比,Pt/CNTs的电化学性能表现出更大的活性.碳纳米管作为阴极材料在质子交换膜燃料电池加氢反应器合成化学品中的作用十分明显.     

SO2存在条件下M/REY催化剂NH3选择性还原NO性能研究

采用浸渍法制备了以REY为载体负载金属氧化物催化剂。采用XRD、NH₃-TPD、NO-TPD、H₂-TPR和XPS对催化剂进行表征,并在固定床微型反应器上评价SO₂存在条件下催化剂在NH₃选择还原NO反应中的活性。实验结果表明,活性组分种类及负载量均影响催化剂性能,Cu(3)/REY催化剂在NH₃选择还原NO反应中表现出较好的低温活性,在SO₂存在条件下,254~390℃时NO的转化率大于95%。催化剂表征结果显示,Cu(3)/REY催化剂的催化活性与其良好的氧化还原性和对NO的吸脱附性能相关。     

有序介孔二氧化硅-碳纳米管复合材料载Pt 及其电催化性能

以十六烷基三甲基溴化铵(CTAB)为结构导向剂, 正硅酸乙酯(TEOS)为硅源, 通过添加碳纳米管(CNTs), 制备介孔二氧化硅包覆碳纳米管网状结构的复合材料(C/Si). X 射线衍射(XRD)和透射电子显微镜(TEM)显示, 介孔二氧化硅的孔道结构高度有序, CNTs 均匀分散于二氧化硅刚性骨架中. 以其为载体微波负载制备了Pt-C/Si-x 纳米粒子催化剂,研究了催化剂在硫酸和甲醇溶液中电催化性能, 结果表明, 具有较高导电性能的复合材料保持了二氧化硅的均匀的孔道结构有利于电解液存储和质子传输, 使得该催化剂显示了良好的电催化活性. 其中碳纳米管添加含量为40 mg 时,催化剂在H₂SO₄ 电解液中的电化学活性面积高达120.9 m²·g^-1, 远大于Pt/CNTs 的电化学活性面积, 对甲醇的催化峰电流也达80.3 mA·cm^-2. 预示其作为直接甲醇燃料电池催化剂载体具有良好的应用前景.     

Pt对Ni2P/MCM-41催化剂加氢脱硫性能的影响

以MCM-41为载体, 采用程序升温还原法制备了含有少量Pt的Ni-P/MCM-41催化剂, 并用氢气程序升温还原(H₂-TPR)、 X射线衍射(XRD)、 N₂吸附比表面积、 X射线光电子能谱(XPS)和透射电子显微镜(TEM)对催化剂的结构和性能进行了表征. 考察了P/Ni摩尔比及Pt含量对Ni-P/MCM-41催化剂催化二苯并噻吩(DBT)加氢脱硫(HDS)性能的影响. 结果表明, Pt能降低Ni₂P催化剂的还原温度, 并有助于Ni₂P相的生成, 抑制团聚现象, 提高催化剂的HDS活性. 当Pt的质量分数为0.6%, P/Ni摩尔比为2时, 催化剂具有最佳加氢脱硫活性, 在340 ℃, 3.0 MPa, 氢油体积比为500, 质量空速(WHSV)为2.0 h^-1的条件下, 二苯并噻吩转化率为100%, 且催化剂加氢脱硫活性在120 h内基本保持稳定.     

焙烧温度对V2O5/CNTs-TiO2催化剂脱氯性能的影响

用浓硝酸纯化改性碳纳米管(CNTs),以钛酸四丁酯为原料,通过溶胶-凝胶法制备碳纳米管-氧化钛(CNTs-TiO₂)复合载体并浸渍制得V₂O₅/CNTs-TiO₂催化剂,重点考察了制备过程中焙烧温度对催化剂催化氧化活性的影响.利用扫描电镜(SEM)、X射线衍射(XRD)仪、X射线光电子能谱(XPS)仪和紫外-可见(UV-Vis)分光光度计等对催化剂材料的结构、形貌和表面化学性质进行了表征分析.结果表明,硝酸处理后的碳纳米管纯度和石墨化程度增加, 450 ℃焙烧温度制备得到的催化剂活性组分分散度好, V₂O₅/CNTs-TiO₂催化剂中钒钛氧均以有利于催化反应的价态存在;催化剂表面活性氧的含量最高,催化剂表现出很好的电子迁移与氧移动的能力,从而提高催化剂的催化活性.实验表明,在250 ℃、催化剂用量为0.2 g、N₂ (80%) + O₂ (20%)下催化降解六氯苯(HCB)的效率可达到94.78%左右,并在24 h内保持很好的稳定性.     

CoAl2O4/Al2O3载体对钴基费托催化剂反应性能影响的研究

通过浸渍和高温焙烧,制得表面附着CoAl₂O₄微晶颗粒的改性Al₂O₃载体,并采用等体积浸渍法制备负载型Co基催化剂。结合 N₂物理吸附、XRD、H₂-TPR、XPS及H₂化学吸附等表征手段,研究改性载体及其负载钴基催化剂的织构特征;采用费托合成反应评价其催化性能。结果表明,Al₂O₃改性后,表面CoAl₂O₄的存在有效减少了载体与活性组分Co的相互作用,显著提高了催化剂的还原度和催化活性。载体的改性量在20%左右达到最佳值,继续增加,催化剂还原度和活性基本不再升高。载体改性促使催化剂CH₄选择性有所降低,C₅₊选择性略有提高。     

Ir/ZrO2催化剂对甲烷催化燃烧性能的研究

采用浸渍法制备了ZrO₂为载体负载Ir的催化剂(Ir/ZrO₂), 考察了催化剂的CH₄催化燃烧性能. 采用X射线衍射(XRD), 拉曼光谱(Raman), X射线光电子能谱(XPS), 氢气程序升温还原(H₂-TPR)等技术对催化剂的结构和Ir物种的存在形式进行了表征. 结果表明, Ir/ZrO₂催化剂中Ir是以IrO₂形式存在的, Ir/ZrO₂催化剂的CH₄燃烧表观活性随着Ir负载量的增加而提高, 并且催化剂表现出较高的催化活性和良好的反应稳定性. 在低Ir负载量(≤1%)时, CH₄燃烧的转换频率(TOF)随着Ir粒子的增大而提高|然而高Ir负载量(≥1%)时, TOF随着Ir粒子的增大保持不变.     

Catalytic activity and stability toward methanol oxidation of PtRu/CNTs prepared by adsorption in aqueous solution and reduction in ethylene glycol

In this paper, we reported an improved process for the preparation of PtRu/CNTs, which involves the adsorption of Pt and Ru ions on CNTs in aqueous solution and the reduction of the adsorbed Pt and Ru ions on CNTs in ethylene glycol. The surface morphology, structure, and compositions of the prepared catalyst were studied by transmission electron microscopy (TEM), X-ray diffraction (XRD), and energy-dispersive spectrometer. TEM observation showed that the particles size of the prepared PtRu alloy was in the range of 2–5 nm, XRD patterns confirmed a face-centered cubic crystal structure. The activity and stability of the prepared catalyst toward methanol oxidation were studied in 0.5 M H₂SO₄ + 1 M CH₃OH solution by cyclic voltammetry, chronoamperometry, and chronopotentiometry. The electrochemical results showed that the prepared catalyst exhibited higher activity and stability toward methanol oxidation than commercial PtRu/C with the same loading amount of Pt and Ru.     

碳纳米管负载高分散Pt纳米颗粒的制备及表征

近年来,碳纳米管(CNTs)[1]作为新型催化剂载体方面的研究[2～11]受到了广泛关注。由于碳纳米管具有纳米级卷曲的表面,与石墨烯相比其表面π键发生变化,从而导致新的电子结构[12],因此碳纳米管负载的催化剂在涉及电子传输过程的催化过程中具有特别的吸引力。燃料电池电极催化剂就是其中典型的一类[13～15]。已有研究者选用碳纳米管作为载体,将Pt[16～19]、PtRu[20,21]等具有催化活性的贵金属或其合金负载到碳纳米管上,展现出了很好的电催化氧化活性。然而,到目前为止,制备用于燃料电池的具有均匀尺寸和分散性的负载型纳米催化剂仍然是一项…     

Ethanol electro-oxidation on catalysts with TiO2 coated carbon nanotubes as support

Pt–TiO₂/CNTs electrocatalysts for direct ethanol fuel cells (DEFCs) were prepared by sol–gel and ethylene glycol reduction method. XRD and TEM showed that the size of the Pt particles on TiO₂/CNTs is 3.5–4 nm and with narrow particle size distribution. HRTEM revealed that a thin layer of uniform amorphous TiO₂ on CNTs was formed and the faces of the Pt crystal on Pt–TiO₂/CNTs catalysts were quite “rough” and “rounded” and some grain bounders and/or twins also appeared. The electrochemical studies using cyclic voltammetry (CV), chronoamperometry and CO stripping voltammetry indicate that Pt–TiO₂/CNTs catalysts have higher electro-catalytic activity and CO-tolerance for ethanol oxidation than Pt/C (20 wt% Pt, E-TEK) and Pt/CNTs catalyst in acid. The Pt/TiO₂ molar ratio was also optimized and proved that 1:1 was the best Pt/TiO₂ molar ratio.     

Pt掺杂对Mo-Ru-Se簇合物电催化氧还原性能的影响

直接甲醇燃料电池(DMFC)是理想的移动电源,但因金属Pt阴极催化剂的选择性较差,甲醇在阴极产生“混合电位”,导致电池效率降低。抗甲醇氧电还原催化剂可降低“混合电位”,是解决该问题的有效的方法。     

纳米三氧化钨复合催化剂的制备及对甲醇电催化性能

采用浸渍沉淀法制备出WO₃-碳纳米管(WO₃-CNTs)纳米复合材料, 微波辅助乙二醇法在其表面负载活性成分Pt, 得到纳米Pt/WO₃-CNTs 催化剂. 采用X射线衍射(XRD), 透射电子显微镜(TEM)和X射线光电子能谱(XPS)等测试手段对催化剂的结构和形貌进行表征, 结果表明Pt 纳米粒子为面心立方晶体结构, 粒径大小在3-5 nm之间, 均匀地分布在WO₃-CNTs 纳米复合材料表面, 同时发现催化剂中的Pt 主要以金属态的形式存在. 采用循环伏安和计时电流法研究了在酸性溶液中Pt/WO₃-CNTs 催化剂对甲醇的电催化氧化性能, 结果表明Pt/WO₃-CNTs 催化剂比用硝酸处理的碳纳米管载铂催化剂(Pt/CNTs)对甲醇呈现出更高的电催化氧化活性和抗CO中毒性能.     

载铂Sr(Zr1－xYx)O3－δ-TiO2异质结光催化剂模拟太阳光催化产氢

利用光化学还原法制备载铂Sr(Zr_1－xY_x)O_3－δ-TiO₂ (Pt-SZYT)异质结光催化剂, 采用XRD, SEM, UV-Vis, PL对催化剂的形貌及性能进行表征. 以工业有机污染物草酸为电子给体, 模拟太阳光下光催化产氢为探针, 评价了催化剂的活性. 研究了载铂量、草酸浓度对催化剂产氢活性的影响, 并探讨了Pt-SZYT催化剂产氢活性与光致发光(PL)性能的关系, 以及催化剂的连续使用效果. 结果表明: 模拟太阳光条件下, Pt-SZYT催化剂具有良好稳定的光催化产氢活性, 催化剂的最佳载铂量为0.90 wt%. PL分析表明Pt-SZYT的光催化产氢活性越高, 其荧光强度越弱. 草酸50 mmol•L^－1, 催化剂用量1.0 g•L^－1时, 催化剂(w＝0.90%) Pt-SZYT-70的平均产氢速率为1.68 mmol•h^－1.     

Photocatalytic hydrogen generation of Pt-Sr(Zr1 − x Y x )O3 − δ -TiO2 heterojunction under the irradiation of simulated sunlight

The Pt-Sr(Zr_{1 − x} Y _x )O_{3 − δ} -TiO₂(Pt-SZYT) heterojunction photocatalysts were prepared by a photodeposition method. The composite particles were characterized by XRD, SEM, UV-Vis DRS, and PL techniques. Photocatalytic hydrogen generation in H₂C₂O₄ aqueous solution under the irradiation of simulated sunlight was used as a probe reaction to evaluate the photocatalytic activity of the photocatalysts. The effects of the content of Pt loading and the concentration of oxalic acid on the photocatalytic activity of the catalyst were discussed. The continuous photocatalytic activity of the Pt-SZYT and the relationship between PL intensity and hydrogen generation were also discussed. The results show that Pt-SZYT catalysts had high photocatalytic activity of hydrogen generation. The content of Pt loading and the concentration of oxalic acid have important influence on the photocatalytic hydrogen generation. The optimal loading content of platinum was 0.90 mass%. Under this condition, the average rate of photocatalytic hydrogen generation was 1.68 mmol·h⁻¹ when the concentration of oxalic acid was 50 mmol·L⁻¹. The higher the photocatalytic activity, the weaker the PL intensity, which was demonstrated by the analysis of PL spectra. __________ Translated from Acta Chimica Sinica, 2008, 61 (in Chinese)     

Small‐Sized Tungsten Nitride Particles Strongly Anchored on Carbon Nanotubes and their Use as Supports for Pt for Methanol Electro‐oxidation

The anchoring of small‐sized WN (tungsten nitride) nanoparticles (NPs) with good dispersion on carbon nanotubes (CNTs) offers an effective means of obtaining promising materials for use in electrocatalysis. Herein, an effective method based on grinding treatment followed by a nitridation process is proposed to realize this goal. In the synthesis, a solution containing H₄[SiO₄(W₃O₉)₄] (SiW₁₂) and CNTs modified with polyethylenimine (PEI‐CNTs) was ground to dryness. Small‐sized WN NPs were anchored onto the CNTs with good dispersion after calcination under NH₃. Under hydrothermal assembly conditions (absence of grinding), WN particles of larger size and with inferior dispersion were obtained, demonstrating the important role of the grinding process. The benefit of the small‐sized WN has been demonstrated by using WN/CNTs as a support for Pt to catalyze the methanol electro‐oxidation reaction. The mass activity of Pt‐WN/CNTs‐G‐70 (where G denotes the grinding treatment, and 70 is the loading amount (%) of WN in the WN/CNTs) was evaluated as about 817 mA mg^?1_Pt, better that those of commercial Pt/C (340 mA mg^?1_Pt) and Pt/CNTs (162 mA mg^?1_Pt). The Pt‐WN/CNTs‐G also displayed good CO tolerance. In contrast, Pt‐WN/CNTs prepared without the grinding process displayed an activity of 344 mA mg^?1_Pt, verifying the key role of grinding treatment in the preparation of WN/CNTs with good co‐catalytic effect.     

ZrO_2负载Pt催化巴豆醛选择性加氢

以高比表面积ZrO2为载体,采用浸渍法制备了负载型Pt催化剂,应用于常压下气相巴豆醛加氢反应,考察了Pt负载量和H2还原温度等对巴豆醛选择性加氢性能的影响.实验结果表明,Pt负载量(质量分数)为3%的3Pt/ZrO2催化剂经500℃还原后,具有较高的巴豆醛选择性加氢性能:巴豆醛转化率为27%,巴豆醇的选择性为55%.X射线粉末衍射(XRD)分析,CO化学吸附,NH3程序升温脱附(NH3-TPD)表征结果表明Pt/ZrO2催化剂上Lewis强酸中心和适宜的Pt颗粒(约为8nm)有利于巴豆醛选择性加氢生成巴豆醇.     

具有优异甲醇催化氧化性能的Pt/MoO3-WO3/CNTs催化剂

以聚二烯丙基二甲基胺盐酸盐(PDDA)为连接剂,采用原位自组装方式将MoO3和WO3负载到碳纳米管(CNTs)上,然后通过乙二醇还原法负载Pt纳米颗粒,得到Pt纳米颗粒均匀分布的Pt/MoO3-WO3/CNTs催化剂.当氧化物总量控制在10 wt%,MoO3与WO3摩尔比为1:0.5时,Pt/MoO3-WO3/CNTs催化剂催化甲醇氧化活性最高,甲醇氧化峰电流If高达835 A/gPt.WO3和MoO3的加入提高了催化剂的甲醇氧化活性、抗CO中毒能力和稳定性,使得Pt/MoO3-WO3/CNTs催化剂表现出优异的甲醇电催化氧化性能.