Surface Adjustment of the SRAO 6-M Antenna Based on Near-Field Radio Holography at 86 GHz

In an attempt to measure and correct the surface profile of the SRAO 6- antenna, we carried out a with-phase holographic experiment at 86 GHz with a transmitter in the near field. Unlike other previous experiments, for cost-effectiveness, we utilized harmonic mixers for frequency conversion together with a microwave synthesizer for local oscillators, while still maintaining the S/N ratio above the required value of 30 dB. We measured the complex beam patterns over ±30 _FWHM both in azimuth and elevation and Fourier-transformed them to obtain the surface profile at 10-cm spatial resolution. It is found that the surface accuracy of the antenna is improved from 100 m to better than 30 m. The edge taper is also estimated to be 11.2 dB in good agreement with the design value, 12 dB. To verify the improvement, we observed the Venus and found that the aperture and beam efficiencies are 72% and 76%, respectively, and are roughly independent of frequency over the whole 3-mm band.     

Corrugated waveguide band edge filters for CMB experiments in the far infrared

Millimetre wave corrugated waveguide-horn structures are used as both single-moded and multi-moded bolometer feeds in a number of cosmic microwave background (CMB) experiments (e.g. PLANCK, Archeops, QUaD). Such horns tend to be employed over a relatively wide bandwidth and for single-moded horns the waveguide acts as the high pass filter. In this paper we report on our investigation on how the waveguide details determine the exact location of the low frequency band edge of such corrugated horns. A sharp step-like band edge, below which there is negligible propagation, is ideally required. Furthermore any leakage below the expected cut-off, possible in corrugated guides, could lead to non-idealised cross-polar effects. Typically deeper corrugations are required in the waveguide filter than at the horn aperture for wide bandwidth operation, thus necessitating a transition section over which the corrugation depth smoothly varies. An electromagnetic mode matching technique and a surface impedance hybrid mode model are used to compute the horn transmission characteristics. We have also undertaken laboratory measurements of the band edge of prototype corrugated horns in order to test the models.     

船载C+S频段共面单脉冲天线设计与应用

本文针对船载测控站空间狭小的特点,介绍了一种C+S双频段共面天线的设计。设计时采用了计算机辅助技术,确定了天线反射面和馈源喇叭的形式及相对关系尺寸。并通过仿真计算和实测结果,该天线在两个频段的方向图指标均满足设计要求,达到了天线的小型化和双频段合建目的,满足航天测量船船载设备的使用要求。     

Design of a Compact Millimeter-Wave Microstrip Antenna with Wide Bandwidth and Broad Beamwidth

Design of a novel compact millimeter-wave microstrip antenna with wide bandwidth and broad beamwidth is presented. In the structure, multiple layers and a parasitic element as well as a coupling aperture are used to achieve wideband, while a conducting cylinder and the coupling aperture are used to obtain broad beamwidth. Finally, phased array with eight present elements has been designed as an example. Compared to traditional microstrip antennas and arrays, present antenna and array are of smaller dimension and broader beamwidth as well as wider bandwidth.     

Corrugated Horn Antenna for Low-Power Testing of the Quasioptical Transmission Lines at TJ-II Stellerator

This paper presents the design and characterisation of a millimetre-wave corrugated horn antenna to perform low power measurements of the main parameters of the quasioptical transmission lines of the Electron Cyclotron Resonance Heating (ECRH) at TJ-II stellerator experiment working in Madrid (E). The antenna generates a practically pure Gaussian Beam at 53.2 GHz that simulates the stellerator gyrotron output beam. Simulations of the designed corrugated horn, by using a specially developed computer code, are presented. The far field radiation pattern of the constructed prototype was measured at the ESTEC Compact Antenna Test Range (CATR). The measurement results are in excellent agreement with those obtained from simulations.     

Very high resolution far infrared synchrotron radiation spectrum of methanol-D1 (CH2DOH) in the first three torsional-vibrational modes

In our effort to systematically study the far infrared (FIR) spectra of asymmetrically mono deuterated methanol (CH₂DOH) and thereby obtain the transition wavenumbers with better and better accuracy (Mukhopadhyay, 2016a,b), the complete Fourier transform (FT) spectra from FIR to infrared (IR) vibrational bands (in the range 50–1190 cm⁻¹) have been re-recorded using the Synchrotron Radiation Source at the Canadian Light Sources in Saskatchewan, Canada. The resolution of the spectrum is unprecedented, reaching beyond the Doppler limited resolution as low as about 0.0008 cm⁻¹ with a signal to noise (S/N) ratio is many fold better than that can be obtained by commercially available FT spectrometer using thermal sources (e.g., Globar). Spectra were also recorded beyond 1190 cm⁻¹ to about 5000 cm⁻¹ at a somewhat lower resolution of 0.002–0.004 cm⁻¹. In this report the analysis of the b-type and c-type torsional - rotational spectra in the ground vibrational state corresponding to gauche- (e₁/o₁) to gauche- (e₁/o₁) and gauche- (e₁/o₁) to trans- (e₀) states in the ground vibrational state are reported and an atlas of the wavenumber for about 2500 FIR assigned absorption lines has been prepared. The transitions within a given sub-band are analyzed using state dependent expansion parameters and the Q-branch origins. The data from previous results (Mukhopadhyay, 2016a,b) along with the present work allowed a global analysis yielding a complete set of molecular parameters. The state dependent molecular parameters reproduce the experimental wavenumbers within experimental uncertainty. In addition, the sensitivity of the spectrum allowed observation of forbidden transitions previously unobserved and helped reassignment of rotational angular momentum quantum numbers of some ΔK = ±1, Q-branch transitions in highly excited states recently reported in the literature. To our knowledge the wavenumbers reported in the present work are the most accurate so far reported in the literature and represent the highest resolution spectra for this molecular species.     

Signal Level Simulation Modeling for Antenna Array of Aperture Synthesis Radiometer Based on the Equivalent Complex Baseband Representations

This paper presents a signal-level simulation model for simulating the process that antenna array of Aperture Synthesis Radiometer (ASR) collecting thermal radiation and transforming thermal radiation signal into radio frequency (RF) signal. By using the equivalent complex baseband signals to represent the practical thermal radiation and RF signals, simulation efficiency is improved significantly. The statistic characteristics of simulation results are found to match the corresponding theoretical analysis well. Results of an imaging simulation experiment show that this model can be employed in ASR system-level simulator design.     

Scaling invariance for the escape of particles from a periodically corrugated waveguide

The escape dynamics of a classical light ray inside a corrugated waveguide is characterised by the use of scaling arguments. The model is described via a two-dimensional nonlinear and area preserving mapping. The phase space of the mapping contains a set of periodic islands surrounded by a large chaotic sea that is confined by a set of invariant tori. When a hole is introduced in the chaotic sea, letting the ray escape, the histogram of frequency of the number of escaping particles exhibits rapid growth, reaching a maximum value at np and later decaying asymptotically to zero. The behaviour of the histogram of escape frequency is characterised using scaling arguments. The scaling formalism is widely applicable to critical phenomena and useful in characterisation of phase transitions, including transitions from limited to unlimited energy growth in two-dimensional time varying billiard problems.     

The design of a radio frequency quadrupole LINAC for the RIB project at VECC Kolkata

A radio frequency quadrupole LINAC has been designed for the VECC-RIB project for an input beam energy of 1.0 keV/u and q/A≥1/16. The output energy will be about 90 keV/u for a 3.4 m long, 35 MHz structure. A half-scale cold model of the RFQ has been fabricated and tested for rf structure design study. The beam dynamics and rf-structure design along with the results of the cold model tests will be presented.     

Polarization Performance of a New Spectrometer Based on a Multilayer-Coated Laminar Grating in the 150-190-eV Region

We constructed a polarization spectrometer based on a laminar grating applied with a Mo/B₄C multilayer coating. The multilayer-coated grating had been previously evaluated to have high polarizance at around 6.7 nm (184 eV) due to the Brewster reflection. In this study the polarization spectrometer was found to be usable in a range from 150 to 190 eV. Using it, σ and π emission spectra in the B 1s emission from a CrB₂ single crystal were separately recorded for the first time in the soft x-ray region. The spectral feature of the emission was reasonably well reproduced by the band calculation.     

The Use of the FDTD Method for Electromagnetic Analysis in the Presence of Indepedently Time-Varying Media

The suitability of the finite-difference time-domain (FDTD) method for electromagnetic modelling in the presence of independently-time-varying materials is investigated. Two examples are given and results compared to those obtained using other theoretical approaches.     

HL-2A 装置ECRH天线系统的结构设计

HL- 2A 装置电子回旋共振加热的天线系统主要由天线外壳、椭球镜、平面镜、转动机构和推动机构组成。转动机构可以推动平面镜环向、极向转动, 进行不同区域的等离子体的加热和电流驱动。平面镜环向转动的角度范围为0°~ 37°, 极向转动的角度范围为0°~ 15 °。给出了驱动杆与平面镜转动角度之间的关系和对应曲线。介绍了椭球镜的安装和推动机构的结构, 给出了椭球镜的椭球面方程。整个天线系统结构紧凑, 安装和拆卸容易, 调节方便。     

��Ƶ���������Ʊ������ٷ��о�

采用射频(RF)等离子体对颗粒形状不规则的钨粉球化,研究了加料速率和钨粉分散方式对球化率的影响。通过用电子扫描显微镜(SEM)观测得到的被球化粉末的百分比评估了球化效率。通过对球化处理的钨粉的X射线衍射谱(XRD)的检测,验证了在球化过程中无氧化发生和其它杂质介入。当钨粉以极短暂时间(约几毫秒)快速穿越等离子体炬时,钨粉颗粒因受热而熔化成液滴,快速冷却后,形成致密的球形固态颗粒。     

射流式单重态氧发生器研究

单重态氧O2 (a1Δg)是迄今唯一能用纯化学反应高效产生的具有长寿命的亚稳激发态分子 .为了考察提出的用两个O2 (1Δ)能量汇集反应生成氧第二单重激发态O2 (b1Σ+ g)以实现近可见短波长化学激光方案的现实性 ,设计和实验了一个氯流量为 3～ 10mmol/s的射流式单重态氧发生器 (JSOG) .考察了三种具有不同孔径和孔数目的喷头、氯气流量和脱水冷阱温度等对JSOG出口的O2 (1Δ)浓度、O2 (1Δ)分压、氯利用率及水蒸气含量的影响 .发现用聚氯乙烯管作冷阱时 ,最佳冷阱介质温度为 - 140～ - 15 0℃ ,对此提出了O2 (1Δ)表面脱活与脱水互相竞争的解释 .在最佳条件下 ,可将O2 (1Δ)气中水分压降低至 4Pa ,这一结果是首次报导     

Practical design of a 4 Tesla double-tuned RF surface coil for interleaved 1H and 23Na MRI of rat brain

MRI is proving to be a very useful tool for sodium quantification in animal models of stroke, ischemia, and cancer. In this work, we present the practical design of a dual-frequency RF surface coil that provides (1)H and (23)Na images of the rat head at 4 T. The dual-frequency RF surface coil comprised of a large loop tuned to the (1)H frequency and a smaller co-planar loop tuned to the (23)Na frequency. The mutual coupling between the two loops was eliminated by the use of a trap circuit inserted in the smaller coil. This independent-loop design was versatile since it enabled a separate optimisation of the sensitivity and RF field distributions of the two coils. To allow for an easy extension of this simple double-tuned coil design to other frequencies (nuclei) and dimensions, we describe in detail the practical aspects of the workbench design and MRI testing using a phantom that mimics in vivo conditions. A comparison between our independent-loop, double-tuned coil and a single-tuned (23)Na coil of equal size obtained with a phantom matching in vivo conditions, showed a reduction of the (23)Na sensitivity (about 28 %) because of signal losses in the trap inductance. Typical congruent (1)H and (23)Na rat brain images showing good SNR ((23)Na: brain 7, ventricular cerebrospinal fluid 11) and spatial resolution ((23)Na: 1.25 x 1.25 x 5mm(3)) are also reported. The in vivo SNR values obtained with this coil were comparable to, if not better than, other contemporary designs in the literature.     

Development of the Microstrip Circulator with a Magnetized Ferrite Sphere in Millimeter Wave Band

In this paper, a novel microstrip circulator with a magnetized ferrite sphere is proposed for various millimeter wave communications. A three-dimensional Finite-Difference Time-Domain (FDTD) approach for the analysis of this ferrite sphere based microstrip circulator is first presented. The electromagnetic fields inside the ferrite junction are calculated using special updating equations derived from the equation of motion of the magnetization vector and Maxwell's curl equations in consistency. Frequency dependent insertion loss, isolation and reflection loss of circulator are calculated over a wide band of frequencies with a single FDTD run. Experimental results at Ka band are presented and compared with theoretical simulations. As a result, a good agreement is found between them.     

可调谐半导体激光器的瞬时光谱测量方法研究

可调谐半导体激光器在调谐过程中的瞬时光谱特性,如瞬时的波长、调谐率、功率、线型和线宽等参数影响着以激光器为光源的光学测量和光相干通信系统的精度。然而,能够同时测量这些瞬变参数的技术至今未见报道。提出了一个基于时频分析的测量半导体激光器在调谐过程中瞬时光谱参数的方法,利用一个短时延外差测量系统,利用激光器瞬时光谱参数与差拍信号瞬时参数的关系,最终获得了半导体激光器在连续电流调谐过程中的瞬时光谱。测量系统采用了10 cm光程差的Mach-Zehnder干涉仪,调谐电流是幅度为20~120 mA、频率是1 kHz的锯齿波,差拍信号可视为直流信号、载波信号与噪声的叠加,按照短时延相干光测量原理,差拍信号中的直流分量幅度的大小反映了激光器输出光信号的功率;载波信号是一种多项式相位信号,由其频率可以推算激光器输出光谱的中心频率或波长;噪声信号则与激光器输出光谱的线型和线宽相关,通过对噪声信号进行时频分析,可以获知激光器在连续电流调谐过程中每一时刻或每个电流下的瞬时线型、线宽。采用了趋势局部均值分解方法对差拍信号进行了准确分离,并对分离信号分别进行处理,同时获知了半导体激光器在调谐过程中的瞬时输出光功率、光波长、调谐率及线型、线宽。在去掉弛豫部分后截取的整周期差拍信号对应的调谐电流60~115 mA变化范围内,半导体激光器(FRL15DDR0A31-18950, Furukawa)瞬时输出光功率变化范围是5.16~10.6 mW,瞬时光波长变化范围为1 579.2~1 579.6 nm;激光器的瞬时调谐率在0.004 8~0.011 5 nm·mA-1范围内单调变化;线宽是852.55~954.95 kHz,呈非线性随机分布。基于短时延、局部均值分解和时频分析方法的瞬时光谱参数测量系统可以准确得到各瞬时光谱参数,测量结果与激光器的静特性相符,且测量系统结构简单,使我们更深入地理解激光器的工作原理,具有广阔的应用前景。     

Band selective small flip angle COSY: a simple experiment for the analyses of 1H NMR spectra of small chiral molecules

The NMR spectroscopic discrimination of enantiomers in the chiral liquid crystalline solvent is more often carried out using ²H detection in its natural abundance. The employment of ¹H detection for such a purpose is severely hampered due to significant loss of resolution in addition to indistinguishable overlap of the spectra from the two enantiomers. This study demonstrates that the band selected small flip angle homonuclear correlation experiment is a simple and robust technique that provides unambiguous discrimination, very high spectral resolution, reduced multiplicity of transitions, relative signs of the couplings and enormous saving of instrument time.     

Thermal Performance of a Capillary Pumped Loop for Automotive Cooling

The design and test results for a capillary pumped loop (CPL) for thermal management of up to 210 W at the source and heat transfer over a distance of 1 m are discussed. The design configuration of the CPL evaporator consists of an internally grooved aluminum evaporator, 31.70-mm outer diameter and 500-mm long, fitted with a porous ultra-high molecular weight polyethylene wick, 8- to 15-μm pore radius, and 38% porous volume. Heat was transferred using a stainless steel tube of 4.5-mm internal diameter for vapor and liquid lines. High-grade acetone (99.99% pure) was used as the heat transfer fluid inside the loop. In the tests, thermal characteristics of the CPL were specifically studied with respect to the temperature control capability using an active thermal device on the reservoir and to the start-up process through pressure priming of the capillary evaporator. The loop was able to start-up successfully at both low and high heat loads, although proper priming of the wick structure before start-up was necessary to attain low evaporator temperatures during steady-state operation. While maintaining constant reservoir temperature through active means, the loop was able to control evaporator temperature within 55 ± 3°C, even with changing input heat from 30 to 210 W. Total thermal resistance from the evaporator surface to the surroundings was 0.19° to 1.15° C/W with the minimum value achieved at the maximum heat load of 210 W. This study is intended to illustrate the thermal potential of the CPL as an effective temperature control device in automotive applications.     

Performance of the low pressure MWPCs for f ission fragments under a high background

Two couples of low pressure multi-wire proportional chambers (MWPC) were located in the target chamber to detect fission fragments in a hypernuclei producing experiment at Thomas Jefferson National Laboratory (Jlab). In the experiment, a continuous wave (CW) electron beam was applied to form hypernuclei by electromagnetic interaction. In the target chamber, the high energy (1.853 GeV) and high intensity (500 nA) primary electron beam caused a high particle background, which influenced the detection of the fission fragments. This report described the design of the MWPCs and studied the fission-fragment detecting performance of them under such a high background. The efficiency of the MWPCs was given with the help of a high resolution kaon spectrometer. At the same time, the background particles were discussed with a Monte Carlo code based on GEANT4.