首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
We have prepared superhydrophobic surfaces which become superhydrophilic by heat-treatment at 500°C or irradiation of UV-light. When hydrolyzed fluoroalkyltrimethoxysilane (FAS) was coated on Al2O3 gel film with a roughness of 20 to 50 nm, the films showed superhydrophobicity and high transparency; the contact angle for water of the film was 165° and the transmittance for the visible light was higher than 92%. When the FAS-coated thin films were heat-treated at temperatures higher than 500°C, the films became superhydrophilic; the contact angle for water on the films was smaller than 5°. Thin films of amorphous TiO2 or anatase TiO2 were coated between Al2O3 gel and FAS layer, and the contact angle for water was also about 160°. UV irradiation using high-pressure mercury lamp on these films resulted in the contact angle to be smaller than 5°. When UV light was irradiated through a photomask, superhydrophobic-superhydrophilic micropatterns applicable as a stamper for printing or a substrate of micro-optical components were successfully obtained on the films.  相似文献   

2.
Irradiation of metallic surfaces using ultra-short pulse laser results in a dual-scale structure. While metallic surfaces are superhydrophilic immediately after laser irradiation, prolonged exposure to air renders surfaces superhydrophobic due to surface reactions and deposition of carbonaceous materials onto the surface. In this work, we have fabricated a paraboloid microstructure, which is analyzed thermodynamically through the use of the Gibbs free energy to obtain the equilibrium contact angle and contact angle hysteresis. The effects of the geometrical details on maximizing the superhydrophobicity of the nanopatterned surface are also discussed in an attempt to design surfaces with desired and/or optimum wetting characteristics.  相似文献   

3.
This article describes development of a simple and convenient method to provide stable low-surface-energy coatings on organic surfaces, by designing and synthesizing a surface-reactive molecule 4-azido-N-dodecylbenzamide, which bears an azide group as the reactive surface anchor and an alkyl chain as the hydrophobic tail. After the hydrophobic modification, rough organic surfaces with contact angle of about 0 degrees can change their surface wetting properties from superhydrophilicity to superhydrophobicity, whose contact angles are above 152 degrees and tilt angles lower than 5 degrees. Moreover, by changing the alkyl chain to a PEO segment, a similar concept can be used to adjust the surface wetting properties from hydrophobic (contact angle approximately 130 degrees) to superhydrophilic (contact angle approximately 0 degrees).  相似文献   

4.
A facial chemical etching method was developed for fabricating superhydrophobic aluminum surfaces. The resultant surfaces were characterized by scanning electron microscopy, water contact angle (WCA) measurement, and optical methods. The surfaces of the modified aluminum substrates exhibit superhydrophobicity, with a WCA of 154.8° ± 1.6° and a water sliding angle of about 5°. The etched surfaces have binary structure consisting of the irregular microscale plateaus and caves in which there are the nanoscale block‐like convexes and hollows. The superhydrophobicity of aluminum substrates occurs only in some structures in which the plateaus and caves are appropriately ordered. The resulted surfaces have good self‐cleaning properties. The results demonstrate that it is possible to construct superhydrophobic surface on hydrophilic substrates by tailoring the surface structure to providing more spaces to trap air. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

5.
Bioactive surfaces with appropriate hydrophilicity for protein immobilization can be achieved by hydrophobin II (HFBI) self-assembly on mica and polydimethylsiloxane (PDMS) surfaces. X-ray photoelectron spectroscopy and water contact angle measurements illustrated that the surface wettability can be changed from superhydrophobic (PDMS) or superhydrophilic (mica) to moderately hydrophilic, which is suitable for protein (chicken IgG) immobilization on both substrate surfaces. The results suggest that HFBI assembly, one kind of hydrophobin from Trichoderma reesei, may be a versatile and convenient method for the immobilization of biomolecules on diverse substrates, which may have potential applications in biosensors, immunoassays, and microfluidic networks.  相似文献   

6.
郑建勇  冯杰  钟明强 《高分子学报》2010,(10):1186-1192
以碳酸钙(CaCO3)颗粒层为模板,运用简单的热压和酸蚀刻相结合的方法制备聚合物超亲水/超疏水表面.首先在玻璃基底上均匀铺撒一层CaCO3颗粒,以此作为模板,通过热压线性低密度聚乙烯(LLDPE)使CaCO3颗粒均匀镶嵌在聚合物表面,获得了超亲水性质;进一步经酸蚀得到了具有微米和亚微米多孔结构的表面,其水滴静态接触角(WCA)可达(152.7±0.8)°,滚动角小于3°,具备超疏水性质.表面浸润性能和耐水压冲击性能研究表明该超疏水表面具有良好的稳定性和持久性.用同样工艺微模塑/酸蚀刻其它疏水性聚合物,得到类似结果.  相似文献   

7.
A simple technique was developed for the fabrication of a superhydrophobic surface on the aluminum alloy sheets. Different hierarchical structures(Ag, Co, Ni and Zn) were formed on the aluminum surface by the galvanic replacement reactions. After the chemical modification of them with fluorination, the wettability of the surfaces was changed from superhydrophilicity to superhydrophobicity. Scanning electron microscopy(SEM), energy dispersive spectrometry(EDS) and water contact angle measurement were performed to characterize the morphological characteristic, chemical composition and superhydrophobicity of the surfaces. The as-prepared superhydrophobic surfaces showed a water contact angle as high as ca.160° and sliding angle as low as ca.3°. We hope the method to produce superhydrophobic surface can be used in many fields.  相似文献   

8.
A novel strategy for a tunable sigmoidal wetting transition from superhydrophobicity to superhydrophilicity on a continuous nanostructured hybrid film via gradient UV-ozone (UVO) exposure is presented. Along a single wetting gradient surface (40 mm), we could visualize the superhydrophobic (thetaH2O > 165 degrees and low contact angle hysteresis) transition (165 degrees > thetaH2O > 10 degrees ) and superhydrophilic (thetaH2O < 10 degrees within 1 s) regions simply through the optical images of water droplets on the surface. The film is prepared through layer-by-layer assembly of negatively charged silica nanoparticles (11 nm) and positively charged poly(allylamine hydrochloride) with an initial deposition in a fractal manner. The extraordinary wetting transition on chemically modified nanoparticle layered surfaces with submicrometer- to micrometer-scale pores represents a competition between the chemical wettability and hierarchical roughness of surfaces as often occurs in nature (e.g., lotus leaves, insect wings, etc).  相似文献   

9.
The article reports on the wetting properties of silicon-based materials as a function of their roughness and chemical composition. The investigated surfaces consist of hydrogen-terminated and chemically modified atomically flat crystalline silicon, porous silicon and silicon nanowires. The hydrogenated surfaces are functionalized with 1-octadecene or undecylenic acid under thermal conditions. The changes occurring upon surface functionalization are characterized using Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS) spectroscopy and water contact angle measurements. By increasing the surface roughness, the static water contact angle increases. The combination of high surface roughness with chemical functionalization with water repellent coating (1-octadecene) enables reaching superhydrophobicity (water contact angle greater than 150°) for silicon nanowires.  相似文献   

10.
Considerable effort has been expended on theoretical studies of superhydrophobic surfaces with two-tier (micro and nano) roughness, but experimental studies are few due to the difficulties in fabricating such surfaces in a controllable way. The objective of this work is to experimentally study the wetting and hydrophobicity of water droplets on two-tier rough surfaces for comparison with theoretical analyses. To compare wetting on micropatterned silicon surfaces with wetting on nanoscale roughness surfaces, two model systems are fabricated: carbon nanotube arrays on silicon wafers and carbon nanotube arrays on carbon nanotube films. All surfaces are coated with 20 nm thick fluorocarbon films to obtain low surface energies. The results show that the microstructural characteristics must be optimized to achieve stable superhydrophobicity on microscale rough surfaces. However, the presence of nanoscale roughness allows a much broader range of surface design criteria, decreases the contact angle hysteresis to less than 1 degrees , and establishes stable and robust superhydrophobicity, although nanoscale roughness could not increase the apparent contact angle significantly if the microscale roughness dominates.  相似文献   

11.
We present a simple method to produce carbon nanotube-based films with exceptional superhydrophobicity and impact icephobicity by depositing acetone-treated single-walled carbon nanotubes on glass substrates. This method is scalable and can be adopted for any substrate, both flexible and rigid. These films have indicated a high contact angle, in the vicinity of 170°, proved both by static and dynamic analysis processes. The dynamic evaporation studies indicated that a droplet deposited on the treated films evaporated in the constant contact angle mode for more than 80% of the total evaporation time, which is definitely a characteristic of superhydrophobic surfaces. Furthermore, the acetone-functionalized films showed a strong ability to mitigate ice accretion from supercooled water droplets (-8 °C), when the droplets were found to bounce off the films tilted at 30°. The untreated nanotube films did not indicate similar behavior, and the supercooled water droplets remained attached to the films' surfaces. Such studies could be the foundation of highly versatile technologies for both water and ice mitigation.  相似文献   

12.
A simple, environmentally benign and energy efficient process for fabricating single faced superhydrophilic/hydrophobic cotton fabrics by controlling surface texture and chemistry at the nano/microscale is reported here. Stable ultra-hydrophobic surfaces with advancing and receding water droplet contact angles in excess of 146° as well as extreme superhydrophilic surfaces are obtained. Hydrophobic water-repellent cotton fabrics were obtained following plasma treatment through diamond-like carbon (DLC) coating by plasma enhanced chemical vapour deposition. The influence of changing different precursor’s plasma pre-treatments such as H2, Ar or O2 on the properties of DLC coatings is also evaluated using atomic force microscopy, X-ray photoelectron spectroscopy, attenuated total reflection Fourier transform infrared spectroscopy, and analysed in terms of contact angle measurements. Because of the DLC coating, the coated fabric showed to endure its superhydrophobic character even after 12 months.  相似文献   

13.
Superhydrophobic surfaces were obtained on copper and galvanized iron substrates by means of a simple solution-immersion process: immersing the clean metal substrates into a methanol solution of hydrolyzed 1H,1H,2H,2H-perfluorooctyltrichlorosilane (CF3(CF2)5(CH2) 2SiCl3, FOTMS) for 3-4 days at room temperature and then heated at 130 degrees C in air for 1 h. Both of the resulting surfaces have a high water contact angle (CA) of larger than 150.0 degrees as well as a small sliding angle (SA) of less than 5 degrees . The formation and structure of the superhydrophobic surfaces were characterized by means of scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and energy-dispersive X-ray spectrometry (EDX). SEM images showed that both of the resulting surfaces exhibited special hierarchical structure. The special hierarchical structure along with the low surface energy leads to the high surface superhydrophobicity.  相似文献   

14.
This paper describes the fabrication of surfaces with different wettability, superhydrophobic/superhydrophilic, and pH-responsive properties. We used a self-assembled monolayer (SAM) of a dendron thiol as the underlying surface for electrodeposition of gold nanostructures. After this modification with a SAM of n-dodecanethiol or 11-mercaptoundecanol, the surface shows remarkable superhydrophobic properties with a contact angle of about 155 degrees and a tilt angle of less than 2 degrees or superhydrophilic properties with a contact angle of about 0 degrees , respectively. Moreover, a large-scale pH-responsive surface was obtained by modification with 2-(11-mercaptoundecanamido)benzoic acid (7) (MUABA). The pH-responsive behavior was amplified by using rough surfaces.  相似文献   

15.
Superhydrophobic and superhydrophilic surfaces are of great interest because of a large range of applications, for example, as antifogging and self‐cleaning coatings, as antibiofouling paints for boats, in metal refining, and for water–oil separation. An aqueous ink based on three‐dimensional graphene monoliths (Gr) can be used for constructing both superhydrophobic and superhydrophilic surfaces on arbitrary substrates with different surficial structures from the meso‐ to the macroscale. The surface wettability of a Gr‐coated surface mainly depends on which additional layers (air for a superhydrophobic surface and water for a superhydrophilic surface) are adsorbed on the surface of the graphene sheets. Switching a Gr‐coated surface between being superhydrophobic and superhydrophilic can thus be easily achieved by drying and prewetting with ethanol. The Gr‐based superhydrophobic membranes or films should have great potential as efficient separators for fast and gravity‐driven oil–water separation.  相似文献   

16.
A new type of superhydrophobic material consisting of a surface with supported Ag@TiO(2) core-shell nanofibers has been prepared at low temperature by plasma-enhanced chemical vapor deposition (PECVD). The fibers are formed by an inner nanocrystalline silver thread which is covered by a TiO(2) overlayer. Water contact angles depend on the width of the fibers and on their surface concentration, reaching a maximum wetting angle close to 180 degrees for a surface concentration of approximately 15 fibers microm(-2) and a thickness of 200 nm. When irradiated with UV light, these surfaces become superhydrophilic (i.e., 0 degrees contact angle). The decrease rate of the contact angle depends on both the crystalline state of the titania and on the size of the individual TiO(2) domains covering the fibers. To the best of our knowledge, this is one of the few examples existing in the literature where a superhydrophobic surface transforms reversibly into a superhydrophilic one as an effect of light irradiation.  相似文献   

17.
Superhydrophobic surfaces, originally inspired by nature, have gained a lot of interest in the past few decades. Superhydrophobicity is a term attributed to the low adhesion of water droplets on a surface, leading to water contact angles higher than 150°. Due to their vast variety of possible applications, ranging from biotechnology and textile industry to power network management and anti-fouling surfaces, many methods have been utilized to develop superhydrophobic surfaces. Among these methods, plasma technology has proved to be a very promising approach. Plasma technology takes advantage of highly reactive plasma species to modify the functionality of various substrates. It is one of the most common surface treatment technologies which is widely being used for surface activation, cleaning, adhesion improvement, anti-corrosion coatings and biomedical coatings. In this paper, recent advances in the applications of plasma technology in the development of superhydrophobic surfaces are discussed. At first, a brief introduction to the concept of superhydrophobicity and plasma is presented, then plasma-based techniques are divided into three main categories and studied as to their applications in development of superhydrophobic surfaces.  相似文献   

18.
Surfaces play an important role in defining the properties of materials, controlling wetting, adsorption, or desorption of biomolecules, and sealing/bonding of different materials. We have combined microscale features with plasma-etched nanoscale roughness and chemical modification to tailor the wettability of the substrates. Cyclic olefin polymers and copolymers (COPs/COCs) were processed to make a range of surfaces with controlled superhydrophobic or -hydrophilic properties. The hydrophobic properties of the polymers were increased by the introduction of microstructures of varying geometry and spacing through hot embossing. The COC/COP substrates were functionalized by plasma activation in O(2), CF(4), and a mixture of both gases. The plasma etching introduces nanoscale roughness and also chemically modifies the surface, creating either highly hydrophilic or highly hydrophobic (contact angle >150°) surfaces depending on the gas mixture. The influence of geometry and chemistries was characterized by atomic force microscopy, contact angle measurements, and X-ray photoelectron spectroscopy. Measurements of the contact angle and contact angle hysteresis demonstrated long-term stability of the superhydrophobic/superhydrophilic characteristics (>6 months).  相似文献   

19.
利用对聚琥珀酰亚胺(PSI)的亲核加成反应,仿生设计合成侧基带有多巴胺和磺酸甜菜碱两性离子基团的新型聚琥珀酰亚胺衍生物(PSI-DA-ZW);通过聚琥珀酰亚胺衍生物中多巴邻苯二酚基团的氧化自聚和沉积,制备了仿生超亲水功能涂层表面(PSI-DA-ZW/glass).利用X射线光电子能谱仪(XPS)、扫描电子显微镜(SEM...  相似文献   

20.
In this study, the authors researched the preparations of superhydrophilic/superhydrophobic surfaces on commercial cup stock polyethylene coated papers by using sparked aluminum nanoparticles deposited on substrates through a sparking process. In this stage, the surface was porous and showed superhydrophilic properties. The samples were then annealed in air at various temperatures and some transformed to superhydrophobicity. It is well known that a suitable roughness in combination with low surface energy has been required to obtain superhydrophobic surfaces. Therefore, it is believed that during annealing process, when polyethylene is diffused from the substrate through the nanoparticle films and the superhydrophobic characteristics were created. The scanning electron microscope images showed that the film surfaces had a fluffy structure for both the as‐deposited and the annealed samples. However, the atomic force microscopy phase images showed completely different surface properties. Moreover, the X‐ray photoelectron spectroscopy spectra showed different surface chemical compositions. The experimental results revealed that the working temperature to produce superhydrophobic surfaces depended on the sparked film thickness. Furthermore, in order to prove the assumption explained above, glass and poly (methyl methacrylate) were also used as substrates.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号