Selective Detection of Dopamine and Its Metabolite,DOPAC, in the Presence of Ascorbic Acid Using Diamond Electrode Modified by the Polymer Film

The surface of boron‐doped diamond (BDD) electrode is modified by the polymer film for the first time. The cationic polymer film of N,N‐dimethylaniline (DMA) is electrochemically deposited on BDD electrode surface. This polymer (PDMA) film‐coated BDD electrode is used as a sensor which selectively detect dopamine (DA) in the presence of ascorbic acid (AA). This electrode also can detect both DA and its metabolite, 3,4‐dihydroxy phenyl acetic acid (DOPAC) in the presence of AA in the range of the physiological concentrations of these species. Favorable ionic interaction (i.e., electrostatic attraction) between the PDMA film and AA or DOPAC lowers their oxidation potentials and enhances the current response for AA and DOPAC compared to that at the bare electrode. The PDMA film also shows a hydrophobic interaction with DA and DOPAC. In cyclic voltammetric measurements, the PDMA film‐coated electrode can successfully separate the oxidation potentials for AA and DA coexisting in the same solution and the separation is about 200 mV. AA oxidizes at more negative potential than DA. In square‐wave voltammetry, the sensitivity of the PDMA film‐coated BDD electrode for DA in the presence of higher concentration of AA is higher than that of the PDMA film‐coated glassy carbon electrode. The hydrodynamic amperometric experiments confirm that the oxidation of AA is not affected by the oxidized product of DA and vice versa. So, unlike the bare electrode the catalytic oxidation of AA by the oxidized DA is eliminated at the PDMA film‐coated BDD electrode. The sensitivities of the modified electrode for AA, DA and DOPAC, which are present in the same solution with their physiological concentration ratios, are calculated to be 0.070, 0.363 and 0.084 μA μM^?1, respectively. The modified electrode exhibits a stable and sensitive response to DA.     

Microchip capillary electrophoresis with a cellulose-DNA-modified screen-printed electrode for the analysis of neurotransmitters

A microfluidic chip based on capillary electrophoresis coupled with a cellulose-single-stranded DNA (cellulose-ssDNA) modified electrode was used for the simultaneous analysis of dopamine (DA), norepinephrine (NE), 3,4-dihydroxy-L-phenylalanine (L-DOPA), 3,4-dihydroxyphenylacetic acid (DOPAC), and ascorbic acid (AA). The modification of the electrode improved the electrophoretic analysis performance by lowering the detection potential and enhancing the signal-to-noise characteristic without surface poisoning of the electrode. The sensitivity of the modified electrode was about 12 times higher than those of the bare ones. The test compounds were separated using a 62 mm long separation channel at the separation field strength of +200 V/cm within 220 s in a 10 mM phosphate buffer (pH 7.4). The most favorable potential for the amperometric detection was 0.7 V (vs. Ag/AgCl). A reproducible response (relative standard deviation of 1.3, 1.3, 2.1, 3.1, 3.4% for DA, NE, L-DOPA, DOPAC, and AA, respectively, for n = 9) for repetitive sample injections reflected the negligible electrode fouling at the cellulose-ssDNA modified electrode. Square-wave voltammetric analyses reflected the sensitivities of the modified electrode for DA, NE, L-DOPA, DOPAC, and AA which were 1.78, 0.82, 0.69, 2.45, and 1.23 nC/microM with detection limits of 0.032, 0.93, 1.13, 0.31, and 0.62 microM, respectively. The applicability of this microsystem to real sample analysis was demonstrated.     

Immobilization of DNA on carbon fiber microelectrodes by using overoxidized polypyrrole template for selective detection of dopamine and epinephrine in the presence of high concentrations of ascorbic acid and uric acid

The overoxidized polypyrrole (PPyox) film as a template for DNA immobilization has been demonstrated in this paper. The DNA molecules inserted into the micropores of the ultrathin PPyox matrix under the driving forces of an electric field and were firmly immobilized on the carbon fiber electrode (CFE). Such a DNA-PPyox biocomposite layer exhibited more effective rejection of anionic ascorbate (AA) and uric acid (UA) and more preferential collection of the cationic dopamine (DA) and epinephrine (EP) than pure PPyox and DNA coatings. The DPV peak currents increased linearly with increasing DA and EP concentrations in the range of 3.0 x 10(-7) to 1.0 x 10(-5) M and 5.0 x 10(-7) to 2.0 x 10(-5) M with the lowest detected concentrations of 8.0 x 10(-8) M and 6.0 x 10(-8) M, respectively. The electrochemical signal of AA could be totally suppressed under a concentration of 20 mM and beyond this concentration, the overlapped responses of AA, DA/EP and UA could be resolved into three well-defined voltammetric peaks. The selectivity factors k(DA/AA) and k(EP/AA) were about 5000 and 2000 for an equal concentration in the presence of 0.5 mM UA. The properties of the biocomposite film have been characterized by atomic force microscopy and electrochemical investigations.     

Poly(4-amino-1-1'-azobenzene-3, 4'-disulfonic acid) coated electrode for selective detection of dopamine from its interferences

Here, we described a new method for electrochemically selective detection of dopamine (DA). In this report, for the first time, electrochemical polymerization of 4-amino-1-1'-azobenzene-3,4'-disulfonic acid (acid yellow 9 dye (AY)) was carried out onto the surface of glassy carbon (GC) electrode and indium tin oxide coated electrode (ITO) from acidic solution containing AY monomers. A polymerized film of acid yellow on the surface of a glassy carbon electrode was characterized by cyclic voltammetry (CV). The redox response of the poly(AY) film on the GC electrode showed a couple of redox peak in 0.1M sulfuric acid solution and the pH dependent peak potential was -58mV/pH which was close to the Nernst behavior. The poly(AY) film-coated GC electrode (GC/PAY) exhibited excellent electrocatalytic activity towards the oxidations of dopamine (DA) in 0.1M phosphate buffer solution (PBS, pH 7.0) and increased the anodic peak current three time higher than bare GC electrode. GC/PAY did not reduce the considerable overpotential for oxidation of DA when compare to bare GC electrode. However, in contrast to other polymer modified electrode, due to the strong negatively charged back bone of poly(AY) highly repelled the important interference of DA, such as ascorbic acid (AA), uric acid (UA) and reduced form of nicotinamide adenine dinucleotide (NADH) in 0.1M PBS (pH 7.0) and did not showed any response for oxidation of these interferences. This behavior makes the GC/PAY for selective detection of DA in the presence of higher concentrations AA, UA and NADH. Using differential pulse voltammetry the calibration curves for DA were obtained over the range of 1-100muM with good selectivity and sensitivity. The proposed method provides a simple method for selective detection of DA from its interferences.     

Electrochemical evaluation of stearate-modified graphite paste electrodes: selective etection of dopamine is maintained after exposure to brain tissue

The electrochemical response characteristics of conventional (CGE) and stearate-modified graphite paste (SGE) electrodes were examined and compared in neutral phosphate-buffered solutions containing dopamine (DA) and other potentially interfering electroactive species found in brain. Cyclic and semiderivative voltammetry at 10 mV/s (slow) and 500 mV/s (rapid) scan rates and chronoamperometry (1 s pulse duration) were used to evaluate the current-potential behavior of these electrodes before and after 20 min or 24 h insertion of the electrode surface in rat brain homogenate solutions. The extent of electrocatalytic and nucleophilic reactions of ascorbate (AA) and glutathione (GSH) on the electrochemical measurement of DA were also assessed at these electrodes. Results from the rapid-scan voltammetric and chronoamperometric experiments indicated that brain treatment of CGEs and SGEs markedly enhanced the resolving power and sensitivity to DA. Both AA and GSH significantly amplified the DA electrochemical signal at untreated SGEs but these effects were considerably attenuated following brain treatment. In addition, brain treatment of CGEs abolished the GSH-induced enhancement of the DA voltammetric signal and modified the CGE to an extent that AA catalysis of DA could be quantified at this electrode surface. These results demonstrated that the selectivity of SGEs for DA was maintained after exposure of the electrode surface to brain tissue and suggest that DA may be selectively monitored in vivo without interference from DOPAC, AA or GSH when used in combination with chronoamperometric or rapid-scan voltammetric techniques.     

Determination of chromium(VI) and total chromium in water by in-electrode coulometric titration in a porous glassy carbon electrode

Chromium(VI) is determined through its direct electrochemical reduction in the bulk of a porous glassy carbon electrode. An electrode filled with the acidified sample and Cr(VI) is reduced by means of a constant current whereas the potential of the electrode is monitored. The limits of detection and quantification were found to be 1.9 and 6.0 μg · L⁻¹, resp. The linear range, repeatability and reproducibility were found to be 5–500 μg · L⁻¹, 1.2, and 1.8%, resp. The influence of Fe(III), Ca(II), Mg(II), sulphates, nitrates, humic acids and surfactants was investigated. Total chromium was measured after chemical oxidation of Cr(III) to chromate by permanganate. The method was applied to analyses of water samples.     

电化学活化碳纤维微电极和脑神经递质及抗坏血酸在体测定

本文采用一种简单电化学方法,即恒电流法处理自制碳纤维电极,在脑神经递质测定中显示了很高的灵敏度和分辨能力.活化后的电极对多巴胺的检测限达5×10^-8mol.dm^-3,对多巴胺和抗坏血酸的伏安峰分离达170mV.作者使用该电极,采用半微分伏安法测定了活体大鼠脑内抗坏血酸,3,4-二羟苯乙酸和5-羟吲哚乙酸的浓度分别为1.7×10^-4,2.1×10^-5和 3.3×10^-6mol·dm^-3.本文对电极的制作,活化条件,伏安峰判别,在体药物实验和电极活化机理等进行了研究和探讨.     

Sensitive Biomimetic Sensor Based on Molecular Imprinting at Functionalized Indium Tin Oxide Electrodes

We initially report an electrochemical sensing platform based on molecularly imprinted polymers (MIPs) at functionalized Indium Tin Oxide Electrodes (ITO). In this research, aminopropyl-derivatized organosilane aminopropyltriethoxysilane (APTES), which plays the role of functional monomers for template recognition, was firstly self-assembled on an ITO electrode and then dopamine-imprinted sol was spin-coated on the modified surface. APTES which can interact with template dopamine (DA) through hydrogen bonds brought more binding sites located closely to the surface of the ITO electrode, thus made the prepared sensor more sensitive for DA detection. Potential scanning is presented to extract DA from the modified film, thus DA can rapidly and completely leach out. The affinity and selectivity of the resulting biomimetic sensor were characterized using cyclic voltammetry (CV). It exhibited an increased affinity for DA over that of structurally related molecules, the anodic current for DA oxidation depended on the concentration of DA in the linear range from 2×10⁻⁶ M to 0.8×10⁻³ M with a correlation coefficient of 0.9927. In contrast, DA-templated film prepared under identical conditions on a bare ITO showed obviously lower response toward dopamine in solution. It should be noted that potential scanning is a very effective approach for DA extraction, and surface modification of the electrochemical transducer with functional monomers is responsible for the development of MIPs-based highly sensitive biomimetic sensor.     

RNA Modified Electrodes for Simultaneous Determination of Dopamine and Uric Acid in the Presence of High Amounts of Ascorbic Acid

A promising electrochemical biosensor was fabricated by electrochemical grafting of ribonucleic acid (RNA) at 1.8 V (vs. SCE) on glassy carbon electrode (GCE) (denoted as RNA/GCE), for simultaneous detection of dopamine (DA) and uric acid (UA) with coexistence of excess amount of ascorbic acid (AA). The electrode was characterized by X‐ray photoelectron spectroscopy (XPS), cyclic voltammetry (CV) and differential pulse voltammetry (DPV) techniques. The RNA modified layer on GCE exhibited superior catalytic ability and anionic exclusive ability in comparison with the DNA modified electrode. Three separated anodic DPV peaks were obtained at 0.312, 0.168 and ?0.016 V for UA, DA and AA, respectively, at the RNA/GCE in pH 7.0 PBS. In the presence of 2.0 mM AA, a linear range of 0.37 to 36 μM with a detection limit of 0.2 μM for DA, and in the range of 0.74 to 73 μM with a detection limit of 0.36 μM for UA were obtained. The co‐existence of 5000 fold AA did not interfere with the detection of DA or UA. The modified electrode shows excellent selectivity, good sensitivity and good stability.     

Highly Sensitive Enzyme-free Sensor Based on a Carbon Paste Electrode Modified with Binary Zinc Oxide/Polyaniline Nanocomposites for Dopamine,Ascorbic Acid and Uric Acid Sensing

Hybrid composites ZnO/PANI were facily synthesized by a sonication process at room temperature. This procedure is non-expensive, time/energy saving and environmentally safe. The as-prepared ZnO/PANI were characterized by FTIR, UV-vis spectroscopies and SEM in order to investigate the structure and morphology of the studied composites. The samples were used to modify carbon paste electrode (CPE) in order to develop electrochemical biosensors (ZnO/PANI/CPE). The sensing properties of the nanoparticles were evaluated for dopamine, ascorbic acid and uric acid non-enzymatic detection. The effect of percentage of polyaniline in the composites and the effect of calcination on the biosensor's response were also examined in the present study. It was revealed that the existence of PANI in ZnO/PANI/CPE largely enhanced the electroactive surface area and therefore the sensitivity for electrochemical sensing. A good electrochemical behavior was noted for ZnO/40 wt% PANI-cal/CPE modified electrode toward DA, AA and UA oxidation. The electroactive surface area of the previously mentioned modified electrode (0.235 cm²) was two times higher than that of the bare electrode (0.117 cm²). The liner relationships between current intensities and concentrations were found to be 0.01–1.4 mM, 0.1–1.3 mM and 0.01–0.12 mM, with detection limit of 0.029 mM, 0.063 mM and 0.007 mM, for DA, AA and UA respectively. In the mixtures of ascorbic acid (AA), dopamine (DA) uric acid (UA) and glucose (Glu) the sensor showed high selectivity of DA with low interference of ascorbic acid by a current change of 14 %. The as-prepared ZnO/PANI/CPE biosensor displayed a good reproducibility and stability.     

蒙脱土修饰碳纤维电极的制备及其应用于活体测定脑神经递质

制备了蒙脱土修饰碳纤维电极,研究了其对神经递质多巴胺(DA)及5羟色胺(5HT)的富集作用,以及对负电性的代谢产物3,4二羟基苯乙酸(DOPAC)、5羟吲哚乙酸(5HIAA)及脑内大量存在的抗坏血酸(AA)排斥性能.该电极具有很高的灵敏度、分辨率和抗干扰性,对DA的检测下限达16×10^-8mol/L,优于传统的Nafion修饰电极,对5HT的检测下限为1×10^-7mol/L.在动物活体分析中,使用该电极成功地检测了大鼠双侧颈总动脉结扎再灌损伤时,脑纹状体中神经递质DA浓度的变化.     

Electropolymerized film of functionalized thiadiazole on glassy carbon electrode for the simultaneous determination of ascorbic acid, dopamine and uric acid

The present study reports the simultaneous determination of ascorbic acid (AA), dopamine (DA) and uric acid (UA) in 0.20 M phosphate buffer solution (pH 5.0) using electropolymerized ultrathin film of 5-amino-2-mercapto-1,3,4-thiadiazole (AMT) on glassy carbon (GC) electrode. The bare GC electrode does not separate the voltammetric signals of AA, DA and UA. However, electropolymerized AMT (p-AMT) modified GC electrode not only resolved the voltammetric signals of AA, DA and UA but also dramatically enhanced their oxidation peak currents when compared to bare GC electrode. The enhanced oxidation currents for AA, DA and UA at p-AMT modified electrode are due to the electrostatic interactions between them and the polymer film. Using amperometric method, we achieved the lowest detection of 75 nM AA, 40 nM DA and 60 nM UA at p-AMT modified electrode. The amperometric current was linearly increased from 200 nM to 0.80 mM for each AA, DA and UA and the lowest detection limit was found to be 0.92, 0.07 and 0.57 nM, respectively (S/N = 3). The practical application of the modified electrode was demonstrated by the determination of DA in dopamine hydrochloride injection.     

Determination of catechol derivatives on pretreatment and copolymer coated glassy carbon electrode

A glassy carbon electrode was pretreated electrochemically and was coated with a copolymer of maleic acid anhydride attached with Eastman-AQ55D (MA/AQ). The voltammetric behavior of a series of biologically important compounds, such as dopamine, L-DOPA, DOPAC, ascorbic acid and uric acid were examined at both pretreated and coated electrodes. Electrochemical pretreatment increased peak current of dopamine and L-DOPA while decreased that of ascorbic acid, uric acid and DOPAC. The copolymer coating caused a decrease of peak currents, but effectively hindered the anionic species (ascorbic acid, uric acid and DOPAC) access to the electrode surface. In flow injection and liquid chromatographic analysis. The dopamine and L-DOPA yielded the better selectivity response at MA/AQ electrode than at bare and AQ electrodes.     

Enhanced sensing of dopamine in the present of ascorbic acid based on graphene/poly(p-aminobenzoic acid) composite film

Graphene/p-aminobenzoic acid composite film modified glassy carbon electrode (Gr/p-ABA/GCE) was first employed for the sensitive determination of dopamine (DA). The electrochemical behavior of DA at the modified electrode was investigated by cyclic voltametry (CV), differential pulse voltametry (DPV) and amperometric curve. The oxidation peak currents of DA increased dramatically at Gr/p-ABA/GCE. The modified electrode was used to electrochemically detect dopamine (DA) in the presence of ascorbic acid (AA). The Gr/p-ABA composite film showed excellent electrocatalytic activity for the oxidation of DA in phosphate buffer solution (pH 6.5). The peak separation between DA and AA was large up to 220 mV. Using DPV technique, the calibration curve for DA determination was obtained in the range of 0.05-10 μM. The detection limit for DA was 20 nM. AA did not interfere with the determination of DA because of the very distinct attractive interaction between DA cations and the negatively Gr/p-ABA composite film. The proposed method exhibited good stability and reproducibility.     

Ion-exchange voltammetry of dopamine at Nafion-coated glassy carbon electrodes: quantitative features of ion-exchange partition and reassessment on the oxidation mechanism of dopamine in the presence of excess ascorbic acid

The incorporation/exclusion features of dopamine (DA), ascorbic acid (AA) and uric acid (UA) are evaluated for Nafion (NA)-coated glassy carbon electrodes (GCE) of different thicknesses. The ion-exchange partition of DA(+) between the NA film and the sodium phosphate electrolyte is evaluated by determining the partition coefficient (k(D)) and the apparent diffusion coefficient (D(app)) in thick NA films which were 401 and 1.5 x 10(-9) cm(2) s(-1), respectively. The solution diffusion coefficient was found to be 6.0 x 10(-6) cm(2) s(-1). Also, the effect of NA loading and of the voltammetric timescale on DA voltammetry in the presence of excess AA is assessed, at physiologic like conditions. It is demonstrated that, although AA is excluded at the NA coating, a catalytic regeneration of DA, induced by AA, occurs at the interface NA film/electrolyte resulting from the diffusion of the o-quinone product of DA oxidation from the electrode surface to that interface. The interference of AA in the voltammetric signal of DA is eliminated using 18 microg mm(-2) NA films and v> or =0.5 V s(-1). Therefore, fast, selective and sensitive voltammetric analysis of DA at concentrations<100 microM in the presence of excess AA, e.g., 1 mM is achieved.     

Simultaneous electroanalysis of dopamine and ascorbic acid using poly (N,N-dimethylaniline)-modified electrodes

Glassy carbon (GC) electrode is modified with an electropolymerized film of N,N-dimethylaniline (DMA). This polymer (PDMA) film-coated GC electrode is used to electrochemically detect dopamine (DA) in the presence of ascorbic acid (AA). Polymer film has the positive charge in its backbone, and in neutral solution DA exists as the positively charged species whereas AA exists as the negatively charged one. In cyclic voltammetric measurements, favorable ionic interaction (i.e., electrostatic attraction) between AA and PDMA film causes a large negative shift of the oxidation potential for AA compared to that at the bare electrode. Oxidation potential for DA is positively shifted due to the electrostatic repulsion. The PDMA film shows hydrophobicity by incorporating uncharged hydroquinone molecule within the film. DA is also incorporated into the film due to hydrophobic attraction even though DA has a positive charge. The responses of DA and AA at polymer-modified electrodes largely change with the concentration of the monomer (i.e., 0.2, 0.1 and 0.05 M DMA) used in electropolymerization and thus with the film thickness. Hydrophobicity of the polymer film shows great influence on the voltammetric responses of both DA and AA. In square wave voltammetric measurements, the PDMA film-coated electrode can separate the DA and AA oxidation potentials by about 300 mV and can detect DA at its low concentration (e.g., 0.2 microM) in the presence of 1000 times higher concentration of AA, which is close to the physiological level. AA oxidizes at more negative potential than DA. The electrode response is not affected by the oxidized product of AA. So unlike the bare electrode, the fouling effect as well as the catalytic oxidation of AA by the oxidized form of DA are eliminated at the PDMA film-coated GC electrode. The electrode exhibits the stable and sensitive response to DA.     

Modified platinum electrode with phytic acid and single-walled carbon nanotube: Application to the selective determination of dopamine in the presence of ascorbic and uric acids

A platinum (Pt) electrode modified by single-walled carbon nanotubes (SWNTs) and phytic acid (PA) was investigated by voltammetric methods in buffer solution. The PA-SWNTs/Pt-modified electrode demonstrated substantial enhancements in electrochemical sensitivity and selectivity towards dopamine (DA) in the presence of L-ascorbic acid (AA) and uric acid (UA). The PA-SWNTs films promoted the electron transfer reaction of DA, while the PA film, acting as a negatively charged linker, combined with the positively charged DA to induced DA accumulation in the film at pH under 7.4. However, the PA film restrained the electrochemical response of the negatively charged AA due to the electrostatic repulsion. The anodic peak potentials of DA, AA and UA could be separated by electrochemical techniques, and the interferences from AA and UA were effectively eliminated in the DA determination. Linear calibration plots were obtained in the DA concentration range of 0.2-10 μM and the detection limit of the DA oxidation current was determined to be 0.08 μM at a signal-to-noise ratio of 3. The results indicated that the modified electrode can be used to determine DA without interference from AA and UA, while ensuring good sensitivity, selectivity, and reproducibility.     

Fabrication of poly(orthanilic acid)–multiwalled carbon nanotubes composite film-modified glassy carbon electrode and its use for the simultaneous determination of uric acid and dopamine in the presence of ascorbic acid

A multiwalled carbon nanotubes (MWNT) modified glassy carbon electrode (GCE) coated with poly(orthanilic acid) (PABS) film (PABS–MWNT/GCE) has been fabricated and used for simultaneous determination of dopamine (DA) and uric acid (UA) in the presence of ascorbic acid (AA) by differential pulse voltammetry (DPV). Scanning electron microscopy, Fourier transform infrared spectra, and electrochemical techniques have been used to characterize the surface morphology of the PABS–MWNT composite film and the polymerization of ABS on electrode surface. In comparison with the bare GCE and the MWNT-modified GCE, the PABS–MWNT composite film-modified GCE, which combines the advantages of MWNT and the self-doped PABS, exhibits good selectivity and sensitivity for the simultaneous and selective determination of UA and DA in the presence of AA. Due to the different electrochemical responses of AA, DA, and UA, PABS–MWNT/GCE can resolve the overlapped oxidation peak of DA and UA into two well-defined voltammetric peaks with enhanced current responses using both cyclic voltammetry (CV) and DPV. The peak potential separations between DA and UA are 170 mV using CV and 160 mV using DPV, respectively, which are large enough for the selective and simultaneous determination of these species. In the presence of 0.5 mM AA, the DPV peak currents are linearly dependent on the concentration of UA and DA in the range of 6–55 and 9–48 μM with correlation coefficients of 0.997 and 0.993, respectively. The detection limits (S/N = 3) for detecting UA and DA are 0.44 and 0.21 μM, respectively. The PABS–MWNT/GCE shows good reproducibility and stability and has been used for the simultaneous determination of DA and UA in the presence of AA in samples with satisfactory results.     

Nation-离子液体-碳纳米管复合膜修饰电极的制备及用于抗坏血酸、多巴胺及尿酸的同时测定

制备了一种新颖的Nation-离子液体一多壁碳纳米管复合膜修饰电极,并研究了抗坏血酸（AA）、多巴胺（DA）和尿酸（uA）在该修饰电极上的电化学行为．该修饰电极结合了多壁碳纳米管良好的导电性、离子液体优良的催化性能及Nation的高选择性等优点,对AA、DA和UA的氧化具有很好的催化和分离效果,实现了AA、DA和UA的同时测定．在三者共存体系中,AA和DA、DA和UA的氧化峰电位差分别为148和167mV．对AA、DA和UA的同时检测,线性范围分别为5-3200、1～1100和1-300gmol／L,检出限分别为1．66、0．33和0．33gmol／L．该修饰电极选择性好、稳定性高、重现性好,有望用于实际样品中AA、DA和UA的同时检测．     

The Influence of the Cathodic Pretreatment on the Electrochemical Detection of Dopamine by Poly(1‐aminoanthracene) Modified Electrode

In this study we demonstrated the influence of the cathodic pretreatment of poly(1‐aminoanthracene) (PAA) electropolymerized on a platinum electrode for determination of dopamine (DA). The DA electrochemical response was obtained after a cathodic pretreatment of the PAA electrode which consisted of applying a potential of ?0.7 V (vs. Ag/AgCl) for 3 s before each measurement. The pretreatment of the electrode changed the PAA electrocatalytic properties so that the electrode began to present electrochemical response to DA without interference of ascorbic acid (AA). The anodic peak currents determined by differential pulse voltammetry using pretreated PAA showed a linear dependence on the DA concentration from 0.56 to 100 µM with a detection limit of 0.13 µM and a correlation coefficient of 0.9986. The electrode exhibits a relative standard deviation of 1.2 % for ten successive measurements of a 0.5 mM DA solution. The analysis by scanning electron microscopy and atomic force microscopy show a homogeneous and nanostructured film with globular structures with diameter of about 20 nm. The analytical results obtained for DA determination at a pretreated PAA electrode in pharmaceutical formulation sample were in good agreement with those obtained by a comparative procedure at a 95 % confidence level. PAA electrode after the pretreatment showed electrochemical responses to DA with excellent selectivity, sensitivity, and high stability without interference of AA.