晶种和磁场诱导联合法制备一维Fe3O4粒子

本文采用晶种和磁场诱导结合的方法制备出了一维Fe3O4纳米粒子,研究了晶种粒径大小、磁场强度、晶种添加量以及晶种分步次数对Fe3O4产品形貌的影响。结果表明,磁场强度增加,棒形颗粒数目增加;晶种分步次数增加,棒形粒子轴比增加;采用三次晶种可以得到轴比为9.0的棒形颗粒;少量的晶种有利于得到轴比一致、形貌均匀的棒形颗粒;大尺寸的晶种有利于得到链形颗粒。同时从颗粒间的相互作用能分析了磁场强度和晶种大小对形貌的影响。     

Preparation of composite particles with magnetic silica core and fluorescent polymer shell

Dual functions of magnetic and fluorescent properties were created in composite particles that incorporated magnetite (Fe₃O₄) nanoparticles in particle cores of silica and fluorescent pyrene in particle shells of polystyrene. The Fe₃O₄ nanoparticles were prepared with a conventional homogeneous precipitation method and surface modified with a coupling agent of carboxyethylsilanetriol. The silica particles incorporating Fe₃O₄ nanoparticles were synthesized with a modified Stöber method in which the Fe₃O₄ nanoparticles were added to a system of tetraethylorthosilicate (TEOS)/ammonia/water/ethanol. Then, the magnetite/silica composite particles were coated with the pyrene/polystyrene shell in a soap-free emulsion polymerization, which was conducted in the presence of pyrene in a mixed solvent of water/ethanol. The composite particles prepared in the mixed solvent had both magnetic and fluorescent properties. The fluorescent spectrum of the particles with Fe₃O₄ was very similar to that without Fe₃O₄, indicating that the magnetic component within the core particles scarcely interfered with the fluorescent emission from the polymer shell.     

中空球状Fe3O4颗粒的合成及对刚果红溶液吸附-脱附能力的研究

通过简单的水热过程合成具有优良磁学性能的中空Fe3O4单晶颗粒。空心球状颗粒外部直径约500 nm,内径约200 nm,是由粒径为50 nm的颗粒团聚而成。随着反应时间的增加,相邻的Fe3O4纳米晶沿着(311)晶面取向团聚,经过奥斯瓦尔德熟化过程最终形成中空的球状颗粒。实验合成的Fe3O4粒子表现出特殊的磁学性能,具有相对较低的饱和磁化强度和较高的矫顽力。通过对刚果红溶液的吸附-脱附实验证明,中空结构Fe3O4颗粒对刚果红溶液有更高的吸附和脱附能力,在废水处理过程中,采用Fe3O4作为吸附剂,可以更高效的去除溶解的有机污染物,同时可以回收再利用,提高废水净化率,也进一步扩展了磁性材料的应用领域。     

GO/Fe3O4/有机胺复合材料的制备及对结晶紫染料的吸附性能

用改进的Hummers法制备了氧化石墨烯,用乙二胺、乙二胺与丁二胺/己二胺混溶来改性氧化石墨烯。用水热法制备了Fe3O4,并用物理混合法制备了GO/Fe3O4/有机胺的三元复合体系。用透射电镜、扫描电镜、红外光谱、热重分析、X射线衍射、VSM和XPS等对所制得的样品进行了结构表征和性能测试,研究了三元复合粒子对结晶紫染料的吸附性能及影响结晶紫染料吸附效果的因素。结果表明:所制备的Fe3O4的平均粒径约为200 nm,粒径分布均匀;复合物中GO为典型的片状结构,GO及有机胺的掺杂没有影响Fe3O4的尖晶石结构;复合物为超顺磁性,Ms为53.0 emu·g~(-1)。吸附结果表明:石墨烯/Fe3O4/有机胺的三元复合材料对结晶紫染料的最大吸附量随浓度增大而增大,而吸附结晶紫染料的移除率却随结晶紫染料浓度增大而减小,并趋向一定值;乙二胺和己二胺混溶比例为5∶1的GO/Fe3O4复合材料吸附性能最佳:结晶紫浓度为400 mg·L~(-1),最大吸附量为164.3 mg·L~(-1)。     

磁性Fe3O4/石墨烯Photo-Fenton催化剂的制备及其催化活性

采用共沉淀法制备磁性Fe3O4/GE(石墨烯)催化剂,实现Fe3O4纳米颗粒生长和氧化石墨烯还原同步进行,采用FTIR、XRD、TEM及低温氮吸附-脱附等对Fe3O4/GE纳米催化剂的物相、颗粒粒径及比表面积进行了表征。在H2O2存在条件下,以亚甲基蓝为目标降解物,考察了在模拟太阳光下Fe3O4/GE的催化活性,当氧化石墨烯与Fe3O4的质量比为1∶10时,经过2 h催化反应,在pH=6条件下,对亚甲基蓝的降解率达到98.7%,经过10次循环使用后对染料溶液的降解率仍保持在95.7%以上,明显优于纯的Fe3O4。     

Synthesis and morphology of an iron oxide/polystyrene/poly(isopropylacrylamide‐co‐methacrylic acid) thermosensitive magnetic composite latex with potassium persulfate as the initiator

In this work, an iron oxide (Fe₃O₄)/polystyrene (PS)/poly(N‐isopropylacryl amide‐co‐methacrylic acid) [P(NIPAAM–MAA)] thermosensitive magnetic composite latex was synthesized by the method of two‐stage emulsion polymerization. The Fe₃O₄ particles were prepared by a traditional coprecipitation method and then surface‐treated with either a PAA oligomer or lauric acid to form a stable ferrofluid. The first stage for the synthesis of the thermosensitive magnetic composite latex was to synthesize PS in the presence of a ferrofluid by emulsion polymerization to form Fe₃O₄/PS composite latex particles. Following the first stage of reaction, the second stage of polymerization was carried out with N‐isopropylacryl amide and methacrylic acid as monomers and with Fe₃O₄/PS latex as seeds. The Fe₃O₄/PS/[P(NIPAAM–MAA)] thermosensitive magnetic particles were thus obtained. The effects of the ferrofluids on the reaction kinetics, morphology, and particle size of the latex were discussed. A reaction mechanism was proposed in accordance with the morphology observation of the latex particles. The thermosensitive property of the thermosensitive magnetic composite latex was also studied. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3062–3072, 2007     

Development of Fe3O4-poly(l-lactide) magnetic microparticles in supercritical CO2

The Fe₃O₄-poly(l-lactide) (Fe₃O₄-PLLA) magnetic microparticles were successfully prepared in a process of solution-enhanced dispersion by supercritical CO₂ (SEDS), and their morphology, particle size, magnetic mass content, surface atom distribution and magnetic properties were characterized. Indomethacin (Indo) was used as a drug model to produce drug-polymer magnetic composite microparticles. The resulting Fe₃O₄-PLLA microparticles with mean size of 803 nm had good magnetic property and a saturation magnetization of 24.99 emu/g. The X-ray photoelectron spectroscopy (XPS) test indicated that most of the Fe₃O₄ were encapsulated by PLLA, which indicated that the Fe₃O₄-PLLA magnetic microparticles had a core–shell structure. After further loading with drug, the Indo-Fe₃O₄-PLLA microparticles had a bigger mean size of 901 nm, and the Fourier transform infrared spectrometer (FTIR) analysis demonstrated that the SEDS process was a typical physical coating process to produce drug-polymer magnetic composite microparticles, which is favorable for drugs since there is no change in chemistry. The in vitro cytotoxicity test showed that the Fe₃O₄-PLLA magnetic microparticles had no cytotoxicity and were biocompatible, which means there is potential for biomedical application.     

可控粒径纳米Fe_3O_4的制备及其磁性研究

本文用空气氧化法,在可见光作用下,添加配合剂(EDTA、柠檬酸、酒石酸、谷氨酸)在室温进行了不同粒径纳米Fe3O4的制备及其磁性能研究。结果表明:在可见光作用下,随EDTA、柠檬酸、酒石酸、谷氨酸等配合剂的添加,得到纳米Fe3O4的粒径有所减小、分散性有所提高;配合剂及可见光共存时,体系反应速率得到提高,高的反应速率使纳米Fe3O4晶粒减小;控制适当的光照度和添加剂的量,室温可得到11.8~29.6nm的Fe3O4颗粒。不同粒径纳米Fe3O4分别呈现出超顺磁性、铁磁性特征。     

磁载光催化剂Fe3O4/C/TiO2的制备及对三氯苯酚的降解

以FeCl3为铁源,葡萄糖为碳源,钛酸四丁酯为钛源,采用水热法制备了磁载光催化剂Fe3O4/C/TiO2,用TEM、EDX、VSM、XRD和IR对Fe3O4/C/TiO2的粒径、形貌和物相等进行了表征。研究了该催化剂对三氯苯酚的降解性能,探讨了其重复使用的可能性,用荧光光谱法推测了可能的反应机理。结果表明该材料结合了光催化与可再生的优点,1 g·L-1 Fe3O4/C/TiO2在18 W紫外灯下,50 min内可将三氯苯酚降解97.9%以上,6次循环使用后降解率仍保持在95.1%,降解过程中有羟基自由基生成。     

磁载光催化剂Fe3O4/C/TiO2的制备及对三氯苯酚的降解

以FeCl₃为铁源, 葡萄糖为碳源, 钛酸四丁酯为钛源, 采用水热法制备了磁载光催化剂Fe₃O₄/C/TiO₂, 用TEM、EDX、VSM、XRD和IR对Fe₃O₄/C/TiO₂的粒径、形貌和物相等进行了表征。研究了该催化剂对三氯苯酚的降解性能, 探讨了其重复使用的可能性, 用荧光光谱法推测了可能的反应机理。结果表明该材料结合了光催化与可再生的优点, 1 g·L^-1 Fe₃O₄/C/TiO₂在18 W紫外灯下, 50 min内可将三氯苯酚降解97.9%以上, 6次循环使用后降解率仍保持在95.1%, 降解过程中有羟基自由基生成。     

可循环磁性Pt/Fe3O4-MCNT催化剂上的肉桂醛选择性加氢反应

采用多步法依次将制备的Fe₃O₄纳米颗粒和Pt纳米颗粒负载到多壁碳纳米管(MCNT)上得到Pt/Fe₃O₄-MCNT磁性催化剂,以X射线衍射(XRD)、透射电镜(TEM)、超导量子干涉磁强计(SQUID)和热重-差热分析(TG-DTA)对Pt/Fe₃O₄-MCNT磁性催化剂的结构和磁性质进行了表征。研究发现预制备的Fe₃O₄纳米颗粒与Pt纳米颗粒均匀地分散于MCNT上,新制备以及多次使用后的Pt/Fe₃O₄-MCNT室温下都具有良好的超顺磁性。研究了Pt/Fe₃O₄-MCNT磁性催化剂上的肉桂醛选择性加氢反应,结果显示催化剂具有良好的C=O加氢活性,肉桂醛转化率在50%左右时,肉桂醇选择性可达96%以上。尺寸均一的Pt粒子均匀的分散在催化剂上可能是催化剂具有良好的C=O加氢选择性的重要原因。在外加磁场作用下催化剂可以高效地从液相反应体系中分离,经多次循环使用后仍具有良好的催化性能。     

空心结构磁性固体碱催化剂Fe3O4@LDO的制备与性能

基于水滑石类化合物的复合氧化物(LDO)是一类性能优异的固体碱催化剂,对其进行改性和功能化引起了越来越多的关注。本文将空心结构和Fe_3O_4引入到镁铝复合氧化物中,制备了一种空心结构磁性固体碱催化剂Fe_3O_4@LDO。这种空心结构磁性固体碱催化剂粒子具有以镁铝复合氧化物为壳层,空心Fe_3O_4为核的核壳结构。由于其独特的空心结构,Fe_3O_4@LDO粒子的悬浊液具有良好的稳定性,将其应用于催化Knoevenagel缩合反应,达到平衡后苯甲醛的转化率约为62%,显示出较好的催化性能。同时,Fe_3O_4@LDO粒子具有较强的磁性,非常方便分离与回收,是一种性能优良的磁性固体碱催化剂。     

磁靶向纳米Fe3O4-TiO2复合物的制备及其对肝癌细胞的光催化杀伤效应

采用三种低温溶胶-凝胶法制备了具有不同Fe₃O₄掺杂量的磁靶向纳米Fe₃O₄-TiO₂复合物, 通过X射线衍射(XRD)、透射电镜(TEM)、傅里叶变换红外(FTIR)光谱、紫外-可见(UV-Vis)光谱、荧光光谱(FS)及磁性能分析等表征方法筛选出包覆均匀、分散性好、磁性能优异及光催化活性较高的纳米Fe₃O₄-TiO₂复合物. 以四甲基偶氮唑蓝(MTT)法检测肝癌细胞(HepG2)的存活率, 考察纳米Fe₃O₄-TiO₂复合物在外磁场作用下对HepG2 细胞的光催化杀伤效应. 结果表明: 采用方法三制备的5%(质量分数)Fe₃O₄-TiO₂复合物具备核-壳结构, 在混悬液中分散性较好, 平均粒径约为50 nm, 具有较强的光催化活性和良好的磁响应性, 同时将纳米TiO₂的光响应范围拓宽至444 nm; 在外磁场作用下, 紫外光和可见光激发纳米Fe₃O₄-TiO₂复合物对HepG2细胞的杀伤效应差异不大, 且均强于纳米TiO₂; 其杀伤效应在0-1.0 T范围内随着外磁场强度的增大而增强.     

多孔朵状Fe_3O_4纳米微球的制备及其性能研究

<正>众所周知,纳米材料的尺寸大小、晶型、形貌构型等结构特征对材料的化学物理性能有重要的影响[1],由于特殊形貌的新材料所具有独特、新颖、高效的化学物理等方面的性质以及在众多领域中的潜在应用[2],特别是3D花状空心纳米结构新物质[3-4],新形貌物质的纳米材料的制备方法和应用特性已经吸引了世界上材料领域的广泛兴趣和关注[5]。目前为止,合成3D纳米结构的方法有自组装法、三维导向连接法以及水热法等,即通过使用有     

Ultrasonic-assisted synthesis of PMMA/Ni0.5Zn0.5Fe2O4 nanocomposite in mixed surfactant system

PMMA/Ni_0.5Zn_0.5Fe₂O₄ nanocomposite with superparamagnetic behavior was synthesized by in situ emulsion polymerization of methylmethacrylate (MMA) monomer in the presence of Ni_0.5Zn_0.5Fe₂O₄ colloidal suspension assisted by ultrasonic irradiation. The obtained samples were characterized by X-ray diffraction (XRD), Fourier transform infrared spectra (FT-IR), transmission electron microscopy (TEM) and vibrating sample magnetometer (VSM). XRD and FT-IR spectra confirmed the formation of PMMA/Ni_0.5Zn_0.5Fe₂O₄ nanocomposite. TEM images showed that Ni_0.5Zn_0.5Fe₂O₄ nanoparticles with the particle sizes of about 12 nm were well dispersed in the polymer matrix. The nanocomposite at room temperature exhibited superparamagnetic behavior under applied magnetic field. The formation mechanism of PMMA/Ni_0.5Zn_0.5Fe₂O₄ nanocomposite was proposed as well.     

Synthesis and morphology of Fe3O4/polystyrene/poly(isopropylacrylamide‐co‐methyl acrylate acid) magnetic composite latex – 2,2′‐azobis (2‐methylpropionamidine) dihydrochloride as initiator

In this work, Fe₃O₄/polystyrene/poly(N‐isopropylacryl amide‐co‐methylacrylate acid) (Fe₃O₄/PS/P(NIPAAM‐co‐MAA)) magnetic composite latex was synthesized by the method of two stage emulsion polymerization. In this reaction system, 2,2′‐azobis(2‐methyl propionamidine) dihydrochloride (AIBA) was used as initiator to initiate the first stage reaction and second stage reaction. The Fe₃O₄ particles were prepared by a traditional coprecipitation method. Fe₃O₄ particles were surface treated by either PAA oligomer or lauric acid to form the stable ferrofluid. The first stage for the synthesis of magnetic composite latex was to synthesize PS in the presence of ferrofluid by soapless emulsion polymerization to form the Fe₃O₄/PS composite latex particles. Following the first stage of reaction, the second stage of polymerization was carried out by the method of soapless emulsion polymerization with NIPAAM and MAA as monomers and Fe₃O₄/PS latex as seeds. The magnetic composite particles, Fe₃O₄/PS/P(NIPAAM‐co‐MAA), were thus obtained. The mechanism of the first stage reaction and second stage reaction were investigated. Moreover, the effects of PAA and lauric acid on the reaction kinetics, morphology, and particle size distribution were studied. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3912–3921, 2007     

可循环磁性Pt/Fe_3O_4-MCNT催化剂上的肉桂醛选择性加氢反应

采用多步法依次将制备的Fe3O4纳米颗粒和Pt纳米颗粒负载到多壁碳纳米管(MCNT)上得到Pt/Fe3O4-MCNT磁性催化剂,以X射线衍射(XRD)、透射电镜(TEM)、超导量子干涉磁强计(SQUID)和热重-差热分析(TG-DTA)对Pt/Fe3O4-MCNT磁性催化剂的结构和磁性质进行了表征。研究发现预制备的Fe3O4纳米颗粒与Pt纳米颗粒均匀地分散于MCNT上,新制备以及多次使用后的Pt/Fe3O4-MCNT室温下都具有良好的超顺磁性。研究了Pt/Fe3O4-MCNT磁性催化剂上的肉桂醛选择性加氢反应,结果显示催化剂具有良好的C=O加氢活性,肉桂醛转化率在50%左右时,肉桂醇选择性可达96%以上。尺寸均一的Pt粒子均匀的分散在催化剂上可能是催化剂具有良好的C=O加氢选择性的重要原因。在外加磁场作用下催化剂可以高效地从液相反应体系中分离,经多次循环使用后仍具有良好的催化性能。     

柠檬酸根对纳米Fe3O4颗粒的生长及性能的影响

现代诊断学的发展使得超小超顺磁性的Fe₃O₄粒子在医学领域具有重要应用价值。实验中利用某些羧酸盐对铁氧化物晶粒成长的抑制作用，在共沉淀法中引入柠檬酸根，制备出平均粒径小于5 nm的Fe₃O₄纳米分散体系。研究了不同柠檬酸根浓度对生成粒子的大小、结晶和表面吸附情况的影响。对Fe₃O₄颗粒在不同条件下的磁性与胶体稳定性进行了讨论。     

Self-assembly approach for the synthesis of electro-magnetic functionalized Fe3O4/polyaniline nanocomposites: Effect of dopant on the properties

Electro-magnetic functionalized Fe₃O₄/polyaniline (PANI) nanocomposites were synthesized by chemical oxidative polymerization in the presence of ammonium peroxydisulfate as an oxidizing agent. Polymerization was carried out independently using two different types of dopants, organic acids (camphorsulfonic acid (CSA) and p-toluenesulfonic acid (TSA)) and inorganic acid (hydrochloric acid). A plausible mechanism for the formation of the nanocomposites (NCs) is presented. During the formation of NCs, CSA/TSA also serves as a micellar template, whereas micelle formation is absent in the case of HCl. Fe₃O₄/PANI-CSA-NC, Fe₃O₄/PANI-TSA-NC and Fe₃O₄/PANI-HCl-NC were characterized for morphology, molecular structure, electrical conductivity and magnetic properties by transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), UV–visible spectroscopy (UV–vis) and superconductor quantum interference device (SQUID) measurements. The results indicate that dopant influence the properties of the NCs. TEM photographs of Fe₃O₄/PANI-CSA and Fe₃O₄/PANI-TSA reveal that the composite particles are spherical having a layer of PANI-CSA or PANI-TSA over Fe₃O₄ nanoparticles. Fe₃O₄/PANI-CSA-NC and Fe₃O₄/PANI-TSA-NC have better morphology, conductivity and high magnetic saturation (M_s) than that of Fe₃O₄/PANI-HCl-NC. Under applied magnetic field, the NCs exhibit the hysteresis loops of the ferromagnetic behavior. M_s value varies with content of Fe₃O₄ present in the composites.     

Effect of capping and particle size on Raman laser-induced degradation of γ-Fe2O3 nanoparticles

Diol capped γ-Fe₂O₃ nanoparticles are prepared from ferric nitrate by refluxing in 1,4-butanediol (9.5 nm) and 1,5-pentanediol (15 nm) and uncapped particles are prepared by refluxing in 1,2-propanediol followed by sintering the alkoxide formed. X-ray diffraction (XRD) shows that all the samples have the spinel phase. Raman spectroscopy shows that the samples prepared in 1,4-butanediol and 1,5-pentanediol and 1,2-propanediol (sintered at 573 and 673 K) are γ-Fe₂O₃ and the 773 K-sintered sample is Fe₃O₄. Raman laser studies carried out at various laser powers show that all the samples undergo laser-induced degradation to α-Fe₂O₃ at higher laser power. The capped samples are however, found more stable to degradation than the uncapped samples. The stability of γ-Fe₂O₃ sample with large particle size (15.4 nm) is more than the sample with small particle size (10.2 nm). Fe₃O₄ having a particle size of 48 nm is however less stable than the smaller γ-Fe₂O₃ nanoparticles.