锐钛矿型多孔TiO2薄膜的溶解法制备及性能表征

在具有锐钛矿晶粒的TiO₂溶胶中加入苯丙乳液粒子，使用该混合液浸渍提拉涂膜，然后利用甲苯将薄膜中的苯丙乳液粒子溶解去除，并通过重复涂膜，在室温下获得了具有良好多孔性的锐钛矿型TiO₂薄膜。考察了多孔薄膜的表面形貌、光学性能、吸附性能和光催化性能。结果表明：随薄膜涂膜次数的增加，TiO₂多孔薄膜的吸光度增大，透光率减小，光吸收边波长向长波方向移动。罗丹明B在TiO₂多孔薄膜上的吸附量随涂膜次数的增加先升高，后降低；多次涂膜会在薄膜中产生半封闭的孔洞，经过长时间的毛细渗透等作用能进一步增加薄膜对罗丹明B的吸附。TiO₂多孔薄膜通过吸附+光催化氧化的模式快速分解罗丹明B，其活性主要受到薄膜在光催化反应初期的吸附能力的影响。此外，TiO₂的负载量、光的利用效率、以及光生电荷迁移及其分离等也是影响薄膜光催化活性的因素。     

Vanadium-containing polyphosphomolybdate immobilized on TiO<Subscript>2</Subscript> nanoparticles: A recoverable and efficient catalyst for Photochemical,Sonochemical and photosonochemical degradation of dyes under irradiation of UV light

A new photocatalyst, nanoporous anatase TiO₂ crystalline particles coupled by Na₅PV₂Mo₁₀O₄₀ Keggin units, TiO₂-PVMo, was prepared by combination of the methods of sol-gel and hydrothermal treatment. The catalyst was characterized by X-ray diffraction (XRD), UV diffuse reflectance spectroscopy (UV-DRS), FT-IR spectroscopy, Scanning Electron Microscopy (SEM) and cyclovoltametery (CV). This photocatalyst exhibited a good photocatalytic (UV region) and sonocatalytic activity in the decomposition of different dyes in aqueous systems. The TiO₂-PVMo composite showed higher photocatalytic and sonocatalytic activity than pure polyoxometalate or pure TiO₂.     

CdS/TiO2纳米管复合结构的制备与光电性能研究

利用阳极氧化法在钛金属基体表面制备一层TiO₂纳米管阵列薄膜, 然后通过水热反应在TiO₂纳米管上负载CdS纳米粒子, 形成CdS/TiO₂纳米管的复合结构。利用SEM、XRD、XPS、UV-Vis等手段对其形貌和结构进行表征。进一步考察了CdS/TiO₂纳米管的光电性能和光催化活性, 结果表明, 相比于TiO₂纳米管, CdS/TiO₂纳米管复合结构在紫外光和可见光下都具有更好的光催化活性及光电性能。     

CdS/TiO2纳米管复合结构的制备与光电性能研究

利用阳极氧化法在钛金属基底表面制备一层TiO2纳米管阵列薄膜,然后通过水热反应在TiO2纳米管上负载CdS纳米粒子,形成CdS/TiO2纳米管的复合结构。利用SEM、XRD、XPS、UV-Vis等手段对其形貌和结构进行表征。进一步考察了CdS/TiO2纳米管的光电性能和光催化活性,结果表明,相比于TiO2纳米管,CdS/TiO2纳米管复合结构在紫外光和可见光下都具有更好的光催化活性及光电性能。     

Preparation of TiO2 Thin Film Photocatalysts by Dip Coating Using a Highly Viscous Solvent

TiO₂ thin film photocatalysts coated onto soda lime glass were prepared by a dip coating process using a highly viscous solvent. The source of the TiO₂ was tetraisopropyl orthotitanate, and -terpineol was used as the solvent. Two types of thin film preparation procedures based on dip coating (a sol-gel system and thermal decomposition system) were used to prepare the samples. TiO₂ thin films were obtained after calcination at 450°C for 1 hour. The film thickness obtained with a single dipping was proportional to the viscosity of the dip coating solutions. The obtained thin films were transparent with a thickness of 1 m. The crystal form of the obtained photocatalyst films was anatase alone. The thin films were formed with aggregated nano-sized TiO₂ single crystals (7–15 nm). The photocatalytic activity of the TiO₂ thin films, as evaluated by the photooxidation of NO (1 ppm) in dry air, was as high as our previous TiO₂ thin films prepared by the sol-gel method.     

Ag@AgCl修饰的锐钛矿相TiO2纳米管的制备及其光催化性能

首先采用水热合成法和双氧水处理制备了具有锐钛矿相的TiO2纳米管,然后通过沉淀和光化学反应将Ag@AgCl纳米粒子负载于其上,从而制得TiO2纳米管负载的表面等离子体光催化剂.结果表明,经Ag@AgCl纳米粒子修饰后,锐钛矿相TiO2纳米管因表面等离子共振效应而对可见光具有明显的响应,光生电子-空穴对更容易分离,因而T...     

Preparation of TiO<Subscript>2</Subscript> nanofibers immobilized on quartz substrate by electrospinning for photocatalytic degradation of ranitidine

The photocatalytic activity of TiO₂ nanofibers immobilized on quartz substrates was investigated by evaluating the decomposition of organic pollutants. TiO₂ nanofibers were synthesized by electrospinning the Ti-precursor/polymer mixture solution, followed by hot-pressing for enhancing the adhesion of TiO₂-nanofiber films to the substrates. TiO₂ started to crystalize in the anatase form at 500 °C and reached the optimal photocatalytic anatase/rutile phase ratio of 70:30 at a calcination temperature of 600 °C. The TiO₂-nanofiber film was demonstrated to be an efficient photocatalyst by ranitidine decomposition under UV illumination and was proven to have a comparable photocatalytic activity with the well-known Degussa P25 nanoparticulate photocatalyst and excellent recyclability during 10 cycles of photocatalytic operation, indicating no loss of TiO₂ nanofibers during photocatalytic operations.     

玻璃微珠/Ag/TiO2可见光催化剂的制备与表征

通过离子交换法将Ag纳米颗粒负载于玻璃微珠的表面及浅表层,并以钛酸四丁酯的乙醇溶液为前驱体,将TiO₂负载于包含银的玻璃微珠表面,制得一种玻璃微珠/Ag/TiO₂复合光催化剂。由于纳米银的表面等离子体吸收效应,该复合光催化剂具有一定的可见光响应特性。利用XRD、SEM对样品进行表征,可发现玻璃微珠表面形成一层均匀多孔的锐钛矿TiO₂,其粒径均在50 nm左右。由漫反射光谱可得出该催化剂具有较强的可见光吸收,并在降解甲基橙溶液的试验中表现出较好的可见光催化活性。     

Fe3+掺杂TiO2/凹凸棒复合光催化剂的制备和光催化活性

用酸催化溶胶-凝胶法制备了Fe³⁺掺杂TiO₂/凹凸棒（Fe³⁺-TiO₂/ATP）复合光催化剂,对其结构、微观形貌、光吸收性能和可见光下的光催化性能进行了表征。XRD和TEM测试结果表明,Fe³⁺-TiO₂/ATP具有较好的热稳定性,经450 ℃热处理后的ATP晶体结构基本保持不变,锐钛矿TiO2均匀的分布在ATP表面,TiO2颗粒之间无团聚,且平均粒径小于纯TiO₂。UV-Vis-DRS测试结果表明,Fe³⁺的掺杂可明显增强复合光催化剂对可见光的吸收,光响应范围拓展到了整个紫外-可见光区。在可见光下,Fe³⁺-TiO₂/ATP复合光催化剂对亚甲基蓝具有很好的催化降解活性。Fe³⁺-TiO₂/ATP的反应速率常数分别为TiO₂/ATP、P25和纯TiO2的1.37、4.83和6.51倍。复合光催化剂的沉降性能优于纯TiO2和P25,易于分离。     

可磁分离二氧化钛光催化剂的制备及其光催化性能

通过液相催化相转化的方法制备了一种可磁分离的光催化剂TiO₂/SiO₂/NiFe₂O₄(TSN),这种光催化剂显示出了超顺磁性,能够通过外加磁场方便的实现催化剂在水中的分离与回收。该光催化剂的X-射线衍射和TEM结果表明：纳米TiO₂颗粒包裹在磁性颗粒-SiO₂/NiFe₂O₄(SN)的周围形成TiO₂层。利用光催化降解甲基橙的效果来考察了这种光催化剂的活性,结果表明：在NiFe₂O₄和TiO₂之间包覆一层无定型的SiO₂,可以显著的提高催化剂的脱色效果,3次循环后,仍能保持良好的催化活性。     

Understanding the synergistic effects,optical and electronic properties of ternary Fe/C/S‐doped TiO2 anatase within the DFT + U approach

Although TiO₂ is an efficient photocatalyst, its large band gap limits its photocatalytic activity only to the ultraviolet region. An experimentally synthesized ternary Fe/C/S‐doped TiO₂ anatase showed improved visible light photocatalytic activity. However, a theoretical study of the underlying mechanism of the enhanced photocatalytic activity and the interaction of ternary Fe/C/S‐doped TiO₂ has not yet been investigated. In this study, the defect formation energy, electronic structure and optical property of TiO₂ doped with Fe, C, and S are investigated in detail using the density functional theory + U method. The calculated band gap (3.21 eV) of TiO₂ anatase agree well with the experimental band gap (3.20 eV). The defect formation energy shows that the co‐ and ternary‐doped systems are thermodynamically favorable under oxygen‐rich condition. Compared to the undoped TiO₂, the absorption edge of the mono‐, co‐, and ternary‐doped TiO₂ is significantly enhanced in the visible light region. We have shown that ternary doping with C, S, and Fe induces a clean band structure without any impurity states. Moreover, the ternary Fe/C/S‐doped TiO₂ exhibit an enhanced photocatalytic activity, a smaller band gap and negative formation energy compared to the mono‐ and co‐doped systems. Moreover, the band edges of Fe/C/S‐doped TiO₂ align well with the redox potentials of water, which shows that the ternary Fe/C/S‐doped TiO₂ is promising photocatalysts to split water into hydrogen and oxygen. These findings rationalize the available experimental results and can assist the design of TiO₂‐based photocatalyst materials.     

Photocatalytic decomposition of Trypan Blue over nanocomposite thin films

The photocatalytic activity of titanium dioxide and gold modified TiO₂ (Au/TiO₂), supported on polymethylmethacrylate (PMMA) thin film, was evaluated in the photodegradation of Trypan Blue (TB) under sunlight irradiation. The effect of parameters such as the photocatalyst amount and pH on TiO₂ photocatalytic activity is investigated. Oxygen flow stream was applied to enhance the decomposition process of TB. The maximum photoactivity was attained using Au/TiO₂-PMMA thin film at pH 2.     

Preparation of SnO2–TiO2/Fly Ash Cenospheres and its Application in Phenol Degradation

SnO₂–TiO₂/fly ash cenospheres (FAC) were prepared via hydrothermal method and used as an active photocatalyst in a photocatalytic system. Scanning electron microscopy, X‐ray diffraction analysis, UV–Vis diffuse reflectance spectroscopy, Fourier transform infrared spectroscopy and N₂ adsorption–desorption measurements were used to determine the structure and optical property of SnO₂–TiO₂/FAC. Phenol was selected as the model substance for photocatalytic reactions to evaluate catalytic ability. Results showed that the degradation efficiency of phenol by SnO₂–TiO₂/FAC was 90.7% higher than that decomposed by TiO₂/FAC. Increased efficiency could be due to the enhanced synergistic effect of semiconductors and FAC could provide more adsorption sites for the pollutant in the photocatalytic reaction. Furthermore, SnO₂–TiO₂/FAC composites exhibited excellent photocatalytic stability in four reuse cycles. Radical‐trapping experiments further revealed the dominating functions of holes in the photocatalytic reaction.     

Low-temperature synthesis of photocatalytic TiO2 thin film from aqueous anatase precursor sols

Anatase TiO₂ sols (RS) were synthesized by peptizing the hydrolysis of titanyl sulfate in abundant hydrogen peroxide solution and subsequent reflux to enhance crystallization. The influences of various reflux time on crystallinity, morphology, and size of the obtained TiO₂ sol and dried TiO₂ film particles were investigated. At room temperature, crystalline TiO₂ thin film was deposited on glass silde from the as prepared TiO₂ sol by dip-coating method. No further thermal posttreatment was required to eliminate organics from the film or to induce titania crystallization. TiO₂ thin film on substrates could be thickened by means of consecutive dip-coating process. Titania film thus obtained was transparent and showed proper adherence. The photocatalytic activities of the TiO₂ thin film was assessed by the degradation of methyl orange in aqueous solution. The preparation process of photocatalytic TiO₂ thin film was quite simple and a low-temperature route.     

Photodegradation of Rhodamine B on Sulfur Doped ZnO/TiO2 Nanocomposite Photocatalyst under Visible-light Irradiation

Sulfur doped ZnO/TiO₂ nanocomposite photocatalysts were synthesized by a facile sol‐gel method. The structure and properties of catalysts were characterized by X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), UV‐vis diffusive reflectance spectroscopy (DRS) and N₂ desorption‐adsorption isotherm. The XRD study showed that TiO₂ was anatase phase and there was no obvious difference in crystal composition of various S‐ZnO/TiO₂. The XPS study showed that the Zn element exists as ZnO and S atoms form SO^2?₄. The prepared samples had mesoporosity revealed by N₂ desorption‐adsorption isotherm result. The degradation of Rhodamine B dye under visible light irradiation was chosen as probe reaction to evaluate the photocatalytic activity of the ZnO/TiO₂ nanocomposite. The commercial TiO₂ photocatalyst (Degussa P25) was taken as standard photocatalyst to contrast the prepared different photocatalyst in current work. The improvement of the photocatalytic activity of S‐ZnO/TiO₂ composite photocatalyst can be attributed to the suitable energetic positions between ZnO and TiO₂, the acidity site caused by sulfur doping and the enlargement of the specific area. S‐3.0ZnO/TiO₂ exhibited the highest photocatalytic activity under visible light irradiation after Zn amount was optimized, which was 2.6 times higher than P25.     

Photocatalytic TiO2 coatings on limestone

The application of photocatalytic coatings on stone has been investigated for providing surface protection and self-cleaning properties. Sol–Gel and hydrothermal processes were used to synthesise TiO₂ colloidal suspensions and coatings with enhanced photocatalytic activity without any thermal curing of the coated stone. The stone was a porous limestone (apulian sedimentary carbonatic, calcite stone). Films and powders prepared from TiO₂ sols were studied using X-ray diffraction to evaluate the microstructure and identify rutile and anatase phases. A morphological and physical characterisation was carried out on coated and uncoated stone to establish the changes of appearance, colour, water absorption by capillarity and water vapour permeability. The photocatalytic activity of the coated surface was evaluated under UV irradiation through NO _x and organics degradation tests. The performances of the synthesised TiO₂ sols were compared with commercial TiO₂ suspension. Since the coating doesn’t need temperature treatments for activating the photocatalytic properties, the nano-crystalline hydrothermal TiO₂ sols seem good candidate for coating applications on stone that cannot be annealed after the coating application.     

Development of TiO<Subscript>2</Subscript> photocatalysts suitable for practical use and their applications in environmental cleanup

Recently, environmental disruption is proceeding on a global scale through the consumption of huge amounts of fossil fuels and the emission of various chemical substances. However, these substances resist bio-treatment. TiO₂ generates electrons and holes by irradiation with light. Most organic micro-pollutants, including dioxins, are decomposed into carbon dioxide and water by the effect of the holes with high oxidative potential. By using such a photocatalytic reaction, various applications are feasible for environmental cleanup. In general, TiO₂ powder has been utilized as photocatalyst, although TiO₂ powder photocatalyst has several disadvantages: (1) it is difficult to handle, (2) photocatalytic reaction is slow and it takes a lot of time for treatment and (3) it is difficult to apply to plastics and textiles, because the photocatalyst decomposes them. We have developed a photocatalyst suitable for practical use and have developed high-activity photocatalysts such as TiO₂ photocatalytic transparent film, photocatalytic silica-gel, apatite-coated TiO₂ photocatalyst usable for plastics and textiles, photocatalytic paper, photocatalytic blue charcoal and photocatalytic oxygen scavenger. The application of these high-activity photocatalysts has been studied in deodorization, anti-bacterial, self-cleaning, anti-stain, water treatment, air purification such as photocatalytic decomposition of dioxins and VOC, and NO _x removal. Now various photocatalytic articles using these new photocatalyst materials are on the market in Japan. Photocatalytic technology can create many valuable products for environmental use all over the world.     

Preparation of photocatalytic nano-ZnO/TiO2 film and application for determination of chemical oxygen demand

A composite nano-ZnO/TiO₂ film as photocatalyst was fabricated with vacuum vaporized and sol-gel methods. The nano-ZnO/TiO₂ film improved the separate efficiency of the charge and extended the range of spectrum, which showed a higher efficiency of photocatalytic than the pure nano-TiO₂ and nano-ZnO film. The photocatalytic mechanism of nano-ZnO/TiO₂ film was discussed, too. A new method for determination of low chemical oxidation demand (COD) value in ground water based on nano-ZnO/TiO₂ film using the photocatalytic oxidation technology was founded. This method was originated from the direct determination of the Mn(VII) concentration change resulting from photocatalytic oxidation of organic compounds on the nano-ZnO/TiO₂ film, and the COD values were calculated from the absorbance of Mn(VII). Under the optimal operation conditions, the detection limit of 0.1 mg l⁻¹, COD values with the linear range of 0.3-10.0 mg l⁻¹ were achieved. The results were in good agreement with those from the conventional COD methods.     

Enhanced photocatalytic activity of Ni doped TiO2 nanowire–nanoparticle hetero–structured films prepared by hydrothermal and sol–gel methods

TiO₂ nanowire-nanoparticle hetero-structured films were prepared via a sol–gel method and coated on glass substrates by dipping method for photocatalytic activity. In this study 0, 1, 3, and 5 mol% of Ni doped were studied. One-dimensional TiO₂ nanowires (NWs) were prepared by hydrothermal treatment with TiO₂ nanoparticles (NPs) which are commercially available. XRD, FESEM, DRS, and XPS were used to characterize the prepared nanowire-nanoparticle hetero-structures films. 3%Ni doped TiO₂ hetero-structured film (TNi3) had the highest photocatalytic activity on the degradation of methylene blue (MB). TNi3 films provided about 4.3 times of degradation rate compared to undoped TiO₂ (T). It revealed that TNi3 film resulted in shifting the absorption wavelength towards narrowing the energy band gap and small crystallite size. Therefore, the TNi3 film exhibited a photocatalytic activity on the degradation of MB under visible light irradiation greater than undoped film.     

铋掺杂二氧化钛纳米颗粒的制备及其可见光催化性能

采用水热法,以纳米管钛酸为前驱物制备了Bi掺杂的TiO₂,并利用X射线衍射、透射电子显微镜、X射线光电子能谱、紫外-可见漫反射光谱等手段对样品进行了表征. 以甲基橙的光催化降解为模型反应评价了样品的可见光催化性能. 结果表明,Bi离子并没有进入TiO₂的晶格中,而是以BiOCl的形式存在. 所制得的BiOCl/TiO₂复合物对甲基橙降解表现出较优越的可见光催化活性;当Bi/Ti摩尔比为1%,水热温度为130℃时,所制催化剂的光催化性能最佳,并对光催化活性提高的机理进行了讨论. 同时,该催化剂对4-氯苯酚降解也表现出较高的光催化性能.