Aerosol-assisted synthesis of mesoporous titania nanoparticles with high surface area and controllable phase composition

Mesoporous titania nanoparticles (denoted as MTN) with high surface area (e.g., 252 m² g⁻¹) were prepared using tetrapropyl orthotitanate (TPOT) as a titania precursor and 10–20 nm or 20–30 nm silica colloids as templates. Co-assembly of TPOT and silica colloids in an aerosol-assisted process and immediate calcination at 450 °C resulted in anatase/silica composite nanoparticles. Subsequent removal of the silica colloids from the composite by NaOH solution created mesopores in the TiO₂ nanoparticles with pore size corresponding to that of silica colloids. Effects of silica colloids’ contents on MTN porosity and crystallites’ growth at a higher calcination temperature (e.g., 1000 °C) were investigated. Silica colloids suppressed the growth of TiO₂ crystallites during calcination at a higher calcination temperature and controllable contents of the silica colloids in precursor solution resulted in various atomic ratios of anatase to rutile in the calcinated materials. The mesostructure and crystalline structure of these titania materials were characterized by transmission electron microscope (TEM), scanning electron microscope (SEM), X-ray diffraction (XRD), differential thermal analysis (DTA)-thermo-gravimetric analysis (TGA), and N₂ sorption.     

Solvothermal synthesis of TiO2: anatase nanocrystals and rutile nanofibres from TiCl4 in acetone

This work reports a new synthetic approach for single‐phase TiO₂ nanomaterials by solvothermal treatment of titanium tetrachloride in acetone at 80–110 °C. Small, uniform, and yet size‐tunable (5–10 nm) anatase titania nanocrystallites were obtained using a low concentration of TiCl₄ in acetone (i.e., at molar ratios of TiCl₄/acetone ≤ 1:15) in the temperature range of 80–110 °C, while rutile nanofibers were synthesized using a high concentration of TiCl₄ (e.g., TiCl₄/acetone = 1:10) at 110 °C. Copyright © 2007 John Wiley & Sons, Ltd.     

Synthesis and photocatalytic activity for water-splitting reaction of nanocrystalline mesoporous titania prepared by hydrothermal method

Nanocrystalline mesoporous TiO₂ was synthesized by hydrothermal method using titanium butoxide as starting material. XRD, SEM, and TEM analyses revealed that the synthesized TiO₂ had anatase structure with crystalline size of about 8 nm. Moreover, the synthesized titania possessed a narrow pore size distribution with average pore diameter and high specific surface area of 215 m²/g. The photocatalytic activity of synthesized TiO₂ was evaluated with photocatalytic H₂ production from water-splitting reaction. The photocatalytic activity of synthesized TiO₂ treated with appropriate calcination temperature was considerably higher than that of commercial TiO₂ (Ishihara ST-01). The utilization of mesoporous TiO₂ photocatalyst with high crystallinity of anatase phase promoted great H₂ production. Furthermore, the reaction temperature significantly influences the water-splitting reaction.     

Synthesis of Spherical Titanium Dioxide Particles by Homogeneous Precipitation in Acetone Solution

Titania powders were synthesized by thermal hydrolysis of titanium tetrachloride in a mixed solvent was studied. The dielectric constant was tuned by regulating the acetone/water volume ratio (R/H ratio) and temperature of the solvent. Hydroxypropyl cellulose (HPC) was used as a steric dispersant. The synthesis were carried out at R/H ratios of 0–4, temperatures of 70–90°C, TiCl₄ concentrations of 0.05–0.2 M, HPC concentrations of 0–5 × 10^–3 g/cm³, and synthesis times of 15–60 min. The TiO₂ particles obtained at an R/H ratio of 0, i.e., pure water system, were fine and agglomerated. In contrast, the TiO₂ particles prepared at an R/H ratio of 3 were uniform and spherical. The TiO₂ particle size increased with increasing TiCl₄ concentration. The synthesis temperature did not influence the particle size, but greatly influenced the morphologyof the TiO₂. Adding HPC to the solution yielded more uniform and spherical particles. In addition, the synthesis time should be longer than 30 min to obtain the most uniform and spherical particles. The dielectric constant of the acetone-water mixed solvent at 28 gave the most uniform and spherical TiO₂ particles. The powders prepared at the condition of 0.1 M TiCl₄, R/H ratio of 3, HPC concentration of 0.001 g/cm³, temperature of 70°C, and synthesis time of 1 h exhibited the most uniform and spherical morphology. The as-synthesized powder was anatase and retained the phase below 400°C. It transformed to the rutile phase after calcination at 700°C.     

Vapor-thermal preparation of highly crystallized TiO2 powder and its photocatalytic activity

Nanocrystalline anatase TiO₂ powder photocatalysts were synthesized by a vapor-thermal method using tetrabutyl titanate as precursor at a temperature range from 120 to 200 °C. The as-synthesized products were characterized by X-ray diffraction, N₂ adsorption-desorption measurement, transmission electron microscopy, high resolution transmission electron microscopy, Fourier transform infrared spectra, Raman spectra, and their photocatalytic activity was evaluated by photocatalytic oxidation decomposition of acetone in air. The results showed that reaction temperature greatly affected the microstructures and photocatalytic activity of the samples. With increasing reaction temperature and time, the average crystalline size of TiO₂ particles increased and their crystallization enhanced, while the specific surface area of the products decreased. The TiO₂ powders obtained at a temperature range from 150 to 200 °C for 10 h showed good photocatalytic activity and were greatly higher than that of Degussa P-25.     

Monitoring of potential cytotoxic and inhibitory effects of titanium dioxide using on-line and non-invasive cell-based impedance spectroscopy

Titanium dioxide (TiO₂) nanoparticles (NPs) with different sizes and structures were probed for plausible cytotoxicity using electric cell-substrate impedance sensing (ECIS), a non-invasive and on-line procedure for continuous monitoring of cytotoxicity. For insect cells (Spodoptera frugiperda Sf9), the ECIS₅₀ values, i.e., the concentration required to achieve 50% inhibition of the response, differed depending on the size and shape of the TiO₂ nanostructure. The lowest ECIS₅₀ value (158 ppm) was observed for the needle shaped rutile TiO₂ (10 nm × 40 nm, 15.5 nm nominal particle size), followed by 211 ppm for P-25 (34.1 nm, 80% anatase and 20% rutile), 302 ppm for MTI5 (5.9 nm, 99% anatase) and 417 ppm for Hombitan LW-S bulk TiO₂ (169.5 nm, 99% anatase). Exposure of TiO₂ NPs to UV light at 254 nm or 365 nm exhibited no significant effect on the ECIS₅₀ value due to the aggregation of TiO₂ NPs with diminishing photocatalytic activities. Chinese hamster lung fibroblast V79 cells, exhibited no significant cytotoxicity/inhibition up to 400 ppm with P25, MTI₅ and bulk TiO₂. However, a noticeable inhibitory effect was observed (ECIS₅₀ value of 251 ppm) with rutile TiO₂ as cell spreading on the electrode surface was prevented     

Synthesis and properties of titanium glycolate Ti(OCH2CH2O)2

A new efficient method for the synthesis of extended micro-and nano-sized crystals (whiskers, fibers) of titanium glycolate Ti(OCH₂CH₂O)₂ has been suggested. The method implies the reaction of hydrated titanium dioxide with ethylene glycol on heating in air. Thermolysis of Ti(OCH₂CH₂O)₂ in air gives titanium dioxide as anatase (400–500°C) and rutile (T > 700°C), the morphology of titanium glycolate crystals being inherited by the oxide. The pseudocrystals of the thermolysis product in an inert gas medium (T = 500–950°C) represent aglomeration of nano-sized titanium dioxide particles and amorphous carbon. At temperatures up to 1300°C, the formation of the TiO_2?x C _x phase with a rutile structure is probable. In a wet air environment, titanium glycolate is partially hydrolyzed to give TiO _x (OCH₂CH₂O)_2?2x (OH)_2x ·xH₂O (0 ≤ x ≤ 1) and on keeping in water at room temperature, ethylene glycol is completely displaced from the crystals. This process is also not accompanied by changes in the particle morphology.     

Thermal annealing synthesis of titanium-dioxide nanowire-nanoparticle hetero-structures

Crystalline TiO₂ nanowire-nanoparticle hetero-structures were successfully synthesized from titanium foils by using a simple thermal annealing method with the aid of CuCl₂ at the atmospheric pressure. Nanowires were grown from Ti foils by simply annealing Ti foils at 850 °C. Then, TiCl₄ was delivered to TiO₂ nanowires so as to precipitate TiO₂ nanoparticles on nanowire surfaces. At 750 °C reaction temperature, nanoparticles of tens of nanometers in diameter were well distributed on pre-grown nanowire forests. Nanoparticles were likely to be precipitated by TiCl₄ decomposition or oxidation and that require high temperatures above ∼650 °C. Electron microscopy, X-ray diffraction, and UV-vis spectroscopy analyses show they have the rutile polycrystalline structure with a slightly enlarged bandgap compared to that of bulk TiO₂. The influence of key synthesis parameters including reaction temperature, reaction time, and quantity of supplied materials on the incorporating nanoparticles was also systematically studied. The optimum reaction condition in the present paper was identified to be 750 °C annealing with repetitive 20 min reactions. A higher reaction temperature yielded larger diameter particles, and higher loading of Ti produced dense particles without changing the particle size. Finally, this method could be utilized for synthesizing other metal oxide nanowires-nanoparticle hetero-structures.     

Fabrication of TiN nanorods by electrospinning and their electrochemical properties

TiN nanorods were synthesized using electrospinning technique followed by thermolysis in different atmospheres. A dimethyl formamide-ethanol solution of poly-(vinyl pyrrolidone) and Ti (IV)-isopropoxide was used as the electrospinning precursor solution and as-spun nanofibers were calcined at 500 °C in air to generate TiO₂ nanofibers. Subsequently, a conversion from TiO₂ nanofibers to TiN nanorods was employed by the nitridation treatment at 600∼1400 °C in ammonia atmosphere. A typical characteristic of the final products was that the pristine nanofibers were cut into nanorods. The conversion from TiO₂ to TiN was realized when the nitridation temperature was above 800 °C. As-prepared nanorods were composed of TiN nano-crystallites and the average crystallite size gradually increased with the increase of the nitridation temperature. Electrochemical properties of TiN nanorods showed strong dependence on the nitridation temperature. The maximum value of the specific capacitance was obtained from the TiN nanorods prepared at 800 °C.     

Kinetics of thermal degradation and estimation of lifetime for polypropylene particles: Effects of particle size

The thermal stability and degradation behavior of polypropylene (PP) particles having diameter varying from few micrometers to nanometers were studied by thermogravimetric analysis (TGA). The PP particles of average diameter ∼20 μm, ∼10 μm, ∼5 μm, ∼1 μm and <500 nm were studied over a range of temperature from 25 to 600 °C in N₂ atmosphere and heating rates of 5, 10 and 15 °C/min. Thermal stability of PP particles initially decreases and then increases as particle size further decreases to nanometer scale. The five single heating rate techniques such as Friedman, Freeman-Carroll, Chang, Coats-Redfern and second Kissinger; and three multiple heating rate techniques such as the first Kissinger, Kim-Park and Flynn-Wall were used to compute the kinetic parameters of degradation reaction, e.g., activation energy (E_a), order of reaction (n) and frequency factor [ln(Z)]. The lifetime of macro-, micro- and nanosized PP particles was also estimated by a method proposed by Toop. It was found that the activation energy and lifetime of nanosized PP particles are moderately high compared to the microsized PP particles. Moreover, the decomposition temperature, order of reaction (n), frequency factor [ln(Z)] not only depend on the heating rate and calculation technique but also on the particle size of polymer. The results are compared with macrosized PP.     

Development of mesoporous TiO2 microspheres with high specific surface area for selective enrichment of phosphopeptides by mass spectrometric analysis

In this study, mesoporous TiO₂ microspheres were synthesized by simple hydrothermal reaction, and successfully developed for phosphopeptides enrichment from both standard protein digestion and real biological sample such as rat brain tissue extract. The mesoporous TiO₂ microspheres (the diameter size of about 1.0 μm) obtained by simple hydrothermal method were found to have a specific surface area of 84.98 m²/g, which is much larger than smooth TiO₂ microspheres with same size. The surface area of mesoporous TiO₂ microspheres is almost two times of commercial TiO₂ nanoparticle (a diameter of 90 nm). Using standard proteins digestion and real biological samples, the superior selectivity and capacity of mesoporous TiO₂ microspheres for the enrichment of phosphorylated peptides than that of commercial TiO₂ nanoparticles and TiO₂ microspheres was also observed. It has been demonstrated that mesoporous TiO₂ microspheres have powerful potential for selective enrichment of phosphorylated peptides. Moreover, the preparation of the mesoporous TiO₂ microspheres obtained by the hydrothermal reaction is easy, simple and low-cost. These mesoporous TiO₂ microspheres with the ability of large scale synthesis can widely be applied for phosphorylated proteomic research.     

A simple route to obtain TiO2 nanowires by the sol–gel method

In this work, titanium dioxide (TiO₂) nanowires were synthesized by the sol–gel method, without using any kind of templates, instead of that acetic acid was used as morphological modifier. In order to control crystalline phases and crystal size, TiO₂ was calcinated at 400, 500 and 600 °C during 1 h. The resulting morphology was nanowires, which diameter was maintained constant after calcination at different temperature (about 76 nm). Moreover, crystalline phases in order of predominance were anatase, anatase–rutile and rutile–anatase at 400, 500 and 600 °C, respectively. Additionally, the crystallite size increases with respect to temperature from 13 to 75 nm.     

Preparation and characterization of Zr doped TiO2 nanotube arrays on the titanium sheet and their enhanced photocatalytic activity

This paper described a new method for the preparation of Zr doped TiO₂ nanotube arrays by electrochemical method. TiO₂ nanotube arrays were prepared by anodization with titanium anode and platinum cathode. Afterwards, the formed TiO₂ nanotube arrays and Pt were used as cathode and anode, respectively, for preparation of Zr/TiO₂ nanotube arrays in the electrolyte of 0.1 M Zr(NO₃)₄ with different voltage and post-calcination process. The nanotube arrays were characterized by field-emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), X-ray photoelectron spectra (XPS) and UV-Vis diffusion reflection spectra (DRS). The photocatalytic activities of these nanotubes were investigated with Rhodamine B as the model pollutant and the results demonstrated that the photocatalytic efficiency of Zr doped TiO₂ nanotubes was much better than that of TiO₂ nanotubes under UV irradiation. Zr/TiO₂ nanotube arrays doped at 7 V and calcined at 600 °C (denoted as TiO₂-7 V-600) achieved the best photocatalytic efficiency and the most optimal doping ratio was 0.047 (Zr/Ti). TiO₂-7 V-600 could be reused for more than 20 times and maintained good photocatalytic activities.     

Effect of crystal form and particle size of titanium dioxide on the photodegradation behaviour of ethylene-vinyl acetate copolymer/low density polyethylene composite

The photodegradation behaviour of ethylene-vinyl acetate copolymer (EVA)/low density polyethylene (LDPE) composite containing four different types of titanium dioxide (TiO₂) was investigated through colour difference, Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and mechanical tests. The results showed that the performance losses of composites were qualitatively correlated with the degradation degree. The vinyl acetate (VA) groups in EVA were sensitive to UV light and the photodegradation mainly occurred in the amorphous region. The chain scission and annealing effect facilitated the secondary crystallization of composites. The heterogeneous nucleation effect of TiO₂ on the crystallization of composites was related to the particle size of TiO₂. The micro rutile TiO₂, micro anatase TiO₂ and their mixture (rutile/anatase = 13/87) exhibited a photo-stabilising effect, while the nano mixed crystals TiO₂ (rutile/anatase = 20/80) had an opposite effect.     

Preparation and characterization of SiO2/TiO2 composite microspheres with microporous SiO2 core/mesoporous TiO2 shell

SiO₂/TiO₂ composite microspheres with microporous SiO₂ core/mesoporous TiO₂ shell structures were prepared by hydrolysis of titanium tetrabutylorthotitanate (TTBT) in the presence of microporous silica microspheres using hydroxypropyl cellulose (HPC) as a surface esterification agent and porous template, and then dried and calcined at different temperatures. The as-prepared products were characterized with differential thermal analysis and thermogravimetric (DTA/TG), scanning electron microscopy (SEM), X-ray diffraction (XRD), nitrogen adsorption. The results showed that composite particles were about 1.8 μm in diameter, and had a spherical morphology and a narrow size distribution. Uniform mesoporous titania coatings on the surfaces of microporous silica microspheres could be obtained by adjusting the HPC concentration to an optimal concentration of about 3.2 mmol L⁻¹. The anatase and rutile phase in the SiO₂/TiO₂ composite microspheres began to form at 700 and 900 °C, respectively. At 700 °C, the specific surface area and pore volume of the SiO₂/TiO₂ composite microspheres were 552 and 0.652 mL g⁻¹, respectively. However, at 900 °C, the specific surface area and pore volume significantly decreased due to the phase transformation from anatase to rutile.     

A template self-assembly strategy to synthesize free-standing TiO2-MO (M = Mg, Co, Ni, Cu or Zn) colloidal films

A series of binary free-standing colloidal films, TiO₂-MO (M = Mg, Co, Ni, Cu and Zn) have been synthesized via a self-assembly technology, utilizing sodium dodecyl sulfonate (SDS) as template and the mixture of titanium butoxide and MCl₂ as precursor. X-ray diffraction (XRD) and transmission electron microscope (TEM) have been employed to characterize TiO₂-MO samples. Results show that TiO₂-MO films are mainly composed by well-ordered nanostructures (e.g. mesoporous particles and lamellar pieces) and more importantly, the increased Ti(OC₄H₉)₄ precursor have significant effect on modifying the as-synthesized nanostructures. A structural model based on SDS micellar template, the complex metallic oxide precursor and charge-density matching between the template and precursor has been proposed. Remarkably, this template self-assembly method has a potential to design a variety of functional multicomponent materials with high-ordered nanostructures, such as high gas sensing SnO₂-ZnO films.     

Nanometer titanium dioxide immobilized on silica gel as sorbent for preconcentration of metal ions prior to their determination by inductively coupled plasma atomic emission spectrometry

Nanometer titanium dioxide immobilized on silica gel (immobilized nanometer TiO₂) was prepared by sol-gel method and characterized by using X-ray diffraction (XRD) and scanning electron microscope (SEM). The adsorptive potential of immobilized nanometer TiO₂ for the preconcentration of trace Cd, Cr, Cu and Mn was assessed in this work. The metal ions studied can be quantitative retained at a pH range of 8-9, and 0.5 mol L⁻¹ HNO₃ was sufficient for complete elution. The adsorption capacity of immobilized nanometer TiO₂ for Cd, Cr, Cu and Mn was found to be 2.93, 2.11, 6.69 and 2.47 mg g⁻¹, respectively. A new method using a microcolumn packed with immobilized nanometer TiO₂ as sorbent has been developed for the preconcentration of trace amounts of Cd, Cr, Cu and Mn prior to their determination by inductively coupled plasma atomic emission spectrometry (ICP-AES). The method has been successfully applied for the determination of trace elements in some environmental samples with satisfactory results.     

Physicochemical Characterization and Catalytic Properties of Titania Gel Doped with Lithium and Rubidium

The effect on titania of doping with lithium and rubidium titania gels has been studied in samples prepared with titanium (IV) tetra-n-butoxide co-gelling with the alkaline metal precursors. Titania and doped titania were characterized by X-Ray diffraction, which showed that the catalysts were nanostructured. In samples calcined at 400°C, the crystallite size of the anatase phase was 17 and 14 nm, and 78 and 38 nm for samples calcined at 600°C, for Li/TiO₂ and Rb/TiO₂, respectively. The specific surface areas of doped samples (400°C) are lower in Li/TiO₂ (90 m²/g) than in Rb/TiO₂(125 m²/g). Evaluation of their basic properties has been carried out in the acetone condensation reaction. It was found that the activity strongly depended on the Li and Rb ionic radii.     

High activity of novel Pd/TiO2 nanotube catalysts for methanol electro-oxidation

Electro-oxidation of methanol in sulfuric acid solution was studied using palladium well-dispersed on titanium nanotubes, in relation to methanol oxidation processes in the direct oxidation methanol fuel cell. Pd dispersed on titania nanotubes, which leads to high surface area substrates, showed excellent catalytic activities compared to those of pure Pd and Pd-TiO₂ nanoparticles. TEM results show a narrow distribution of TiO₂ nanoparticles whose particle size is about 10 nm, and uniform nano-sized TiO₂ nanotubes with 10 nm in diameters are seen from HRTEM . A homogeneous structure in the composite nanomaterials is indicated by XRD analysis. The composite electrode activities were measured by cyclic voltammetry (CV) and at 25 °C it was found that 3 wt% Pd in titania nanotubes had the best activity for methanol oxidation.     

A highly sensitive electrochemical sensor for simultaneous determination of hydroquinone and bisphenol A based on the ultrafine Pd nanoparticle@TiO2 functionalized SiC

A titanium dioxide–silicon carbide nanohybrid (TiO₂–SiC) with enhanced electrochemical performance was successfully prepared through a facile generic in situ growth strategy. Monodispersed ultrafine palladium nanoparticles (Pd NPs) with a uniform size of ∼2.3 nm were successfully obtained on the TiO₂–SiC surface via a chemical reduction method. The Pd-loaded TiO₂–SiC nanohybrid (Pd@TiO₂–SiC) was characterized by transmission electron microscopy and X-ray diffractometry. A method for the simultaneous electrochemical determination of hydroquinone (HQ) and bisphenol A (BPA) using a Pd@TiO₂–SiC nanocomposite-modified glassy carbon electrode was established. Utilizing the favorable properties of Pd NPs, the Pd@TiO₂–SiC nanohybrid-modified glassy carbon electrode exhibited electrochemical performance superior to those of TiO₂–SiC and SiC. Differential pulse voltammetry was successfully used to simultaneously quantify HQ and BPA within the concentration range of 0.01–200 μM under optimal conditions. The detection limits (S/N = 3) of the Pd@TiO₂–SiC nanohybrid electrode for HQ and BPA were 5.5 and 4.3 nM, respectively. The selectivity of the electrochemical sensor was improved by introducing 10% ethanol to the buffer medium. The practical application of the modified electrode was demonstrated by the simultaneous detection of HQ and BPA in tap water and wastewater samples. The simple and straightforward strategy presented in this paper are important for the facile fabrication of ultrafine metal NPs@metal oxide–SiC hybrids with high electrochemical performance and catalytic activity.