宽工作温度烟气脱硝催化剂制备及反应机理研究

以溶胶-凝胶法制备介孔TiO2载体,采用分步浸渍法制备了V2O5-WO3/TiO2催化剂,借助BET、NH3-TPD、H2-TPR、SEM、活性评价、In-situ FT-IR等手段,考察了催化剂的结构、酸性、还原性、脱硝活性及反应机理等。介孔TiO2载体比表面积为158.6 m2/g,制成催化剂后比表面积略有降低,约为136.7 m2/g。针对模拟烟气在φNH3/φNO=0.8的条件下测试催化剂的脱硝活性温度窗口为250~400℃,脱硝转化率达到80%。NH3-TPD和H2-TPR表征结果表明,催化剂在活性温度范围内具有典型的表面酸性位,载体TiO2与V2O5之间存在的相互作用使得V2O5还原温度降低。利用In-situ FT-IR研究NH3和NO在V2O5-WO3/TiO2催化剂表面吸附和氧化的反应过程发现,NH3可同时吸附在L酸位和B酸位,NH3在活性位上氧化脱氢形成NH2物种是SCR脱硝反应的控制步骤。研究NO+O2+NH3反应时发现,吸附NH3的催化剂引入NO和O2后,共价吸附的NH3首先消失。选择性催化还原反应发生在吸附态NH3和气态或弱吸附态的NO之间,该反应遵从Eley-Rideal反应机理。     

土壤样品中砷的形态分析方法研究

对生态地球化学土壤样品,在Tessier修正顺序提取方法(即七步法)的基础上对提取方法、提取时间、提取溶液的处理方法进行优化选择,用超声法提取水溶态、离子交换态、碳酸盐结合态、腐殖酸结合态、铁锰氧化物结合态、强有机质结合态和残渣态七种形态的砷元素,用原子荧光光谱法测定各个形态砷的含量。优化后的方法测得As元素各形态的检出限均小于1.0μg/g,相对标准偏差(RSD)小于10%,准确度高,质量参数均满足生态地球化学土壤样品评价形态分析的需要。     

V2O5/ACF催化剂低温下选择性催化还原NO的机理

将V2O5担载在活性炭纤维(ACF)上制得V2O5/ACF催化剂,并采用暂态响应实验和NH3吸附氧化实验等考察了影响V2O5/ACF催化剂上选择性催化还原(SCR)反应的关键因素.结果表明,NH3在催化剂表面的吸附是必要的,而且该吸附是一个快速过程;气相O2的存在有利于形成催化剂中所需的活性氧化态物种.NH3吸附.脱附与原位质谱相结合的实验表明,V2O5/ACF催化剂具有吸附NH3和将NH3氧化为N2H2的能力,N2H2为NH3氧化的一种中间体.     

Li改性MnO_2及LiMn_2O_4催化NH_3-SCR反应性能研究

采用高温固相反应法、Pechini合成方法和柠檬酸配位法,制备了系列锂锰复合氧化物LiMn2O4催化剂,应用于NH3-SCR反应,并与固相反应法合成的MnO2进行了比较。采用N2吸附-脱附、扫描电镜、X射线衍射、H2程序升温还原、NH3程序升温脱附、NO程序升温脱附和X射线光电子能谱对LiMn2O4催化剂进行表征。结果表明,引入Li有利于提高锰基催化剂的SCR活性和抗硫性。Pechini法制备LiMn2O4的NO转化率可在130~260℃达到90%以上;固相反应法制备LiMn2O4的NO转化率大于90%的温度为90~310℃;MnO2的温度窗口则仅为140~280℃。与MnO2相比,引入Li可形成LiMn2O4结构,因此,催化剂中更多的锰离子保持在相对较低的价态Mn3+,并调整表面活性氧含量;同时,Li的存在调变了LiMn2O4表面的酸位,从而减少高温下MnO2表面容易发生的NH3非选择性氧化,改善其催化NH3-SCR反应的温度窗口,也增强了抗硫性。     

可溶性有机质对污染土壤中铊迁移行为的影响

目的 为了查明可溶性有机质（DOM）对土壤中污染元素铊赋存形态的影响,方法 采用形态分级提取方法,将土壤中的铊重金属分成酸可交换态、铁锰氧化物结合态、有机质结合态和残留态4组分,并采用Elan 6100型ICP-MS质谱仪测定各组分中铊的质量浓度.结果 DOM可降低酸可交换态的Tl,增加铁锰氧化物结合态和有机质结合态Tl的百分含量,但对残留态Tl的百分含量没有明显影响.因此,DOM可降低铊在土壤中的活动性,从而改变了铊在土壤中的迁移行为.结论 可溶性有机质（DOM）自身的络合（螯合）能力及其吸附特性是改变重金属铊形态分布的主要因素.     

紫外光降解-离子色谱法测定液晶材料中有机分子上的碱、碱土金属和铵

采用紫外光降解－离子色谱法测定了液晶材料中的阳离子。研究了样品光降解的条件，H2O2及酸的影响，样品基体有机物的去除，并对直接水溶样品，超声提取样品和光解样品和光解样品测定结果进行了对比。结果表明：3种样品中均含有Na^ ,NH4^ ,K^ ,Mg^2 ,Ca^2 5种阳离子，但光解样品中5种阳离子的含量分别是超声提取及直接水溶样品中含量的3．5－19．7倍和10．6－46．6倍。对液晶样品进行光解测定阳离子时无需加入H2O2氧化，光解后无需对样品进行酸化。Na^ ,NH4^ ,K^ 在光解1.5h时响应值达到最大，Mg^2 ,Ca^2 在2h时光解最完全。5种阳离子加标回收率为71．5％－107．6％。本方法对测定有机化合物上结合的阳离子有一定的参考价值。     

原子吸收光谱法测定烟叶中的重金属总量及形态分析

采用火焰原子吸收光谱法测定烟叶中Mn,Cu,Zn元素,石墨炉原子吸收光谱法测定Cd,Cr,Pb元素,以HNO3-H2O2微波消解法获取烟叶中的重金属总量,以超声水提取法获取水溶态重金属进行初级形态分析,以Tessier逐级提取法获取5种形态的重金属进行次级形态分析。实验结果表明,原子吸收光谱法检测6种重金属线性良好,相关系数(r2)不低于0.998 8,检出限为0.16~3.1μg·L-1。烟叶样品中Mn,Cu,Zn,Cd元素主要以可交换态和碳酸盐结合态的形式存在;Cr主要以残渣态的形式存在;而Pb主要以碳酸盐结合态和残渣态的形式存在。     

钙对氟污染酸性土壤的改良效应

对珠三角典型土壤（潮土和水稻土）加入一系列硝酸钙、氧化钙和碳酸钙进行室内培养,采用连续化学提取方法对原土及添加上述成分后各种形态氟进行提取,并采用极谱测定方法进行检测,研究各形态的转化行为。试验结果表明：加入氧化钙和碳酸钙可使两种土壤pH值明显上升,有利于改善土壤酸性;但使两种土壤有效态氟（水溶态氟、可交换态氟）含量上升,而铁锰结合态氟总体下降。故氧化钙不适用于该类高氟土的酸性改良,而碳酸钙的适用性则由土壤理化性质决定。硝酸钙的加入使各形态氟含量均呈下降趋势,在施用剂量大于20mg／25g时,对土壤中有效态氟有较好的抑制作用,但对土壤酸化没有改善。     

乙烷部分氧化超细Fe－Mo－O催化剂的研究

采用溶胶-凝胶法制备了Fe－Mo－O催化剂，用XRD、TEM、BET、IR、TPR、TPD和微反等技术研究了催化剂晶体结构、表面构造、晶格氧活泼性、化学吸附和乙烷部分氧化反应性能。Fe－Mo－O复合氧化物催化剂是由超细微粒组成，微粒粒径约10 nm～20 nm，比表面积为48.1 m2/g。催化剂表面由Lewis碱位（Mo=O键的端氧和Fe－O－Mo键中的桥氧）及Lewis酸位构成。乙烷能以甲基中的H原子吸附在催化剂表面Lewis碱位Mo=O的端氧上形成分子吸附态，其部分氧化产物主要是C2H4和少量的CH3CHO。     

CO2和CH3OH直接合成碳酸二甲酯Cu-Ni/V2O5-SiO2催化剂

采用表面反应改性法制备了V2O5 SiO2(VSiO)表面复合物 ,用等体积浸渍法制备了VSiO担载的Cu Ni双金属催化剂 ,用IR、TPD、TPSR和微反技术研究了CO2 和CH3OH在催化剂表面上的化学吸附与反应性能.结果表明,在Cu Ni/VSiO催化剂上存在着金属位Cu Ni合金、Lewis酸位Vn 和Lewis碱位V=O三类活性中心 ;CO2 在金属位和Lewis酸位协同作用下可生成CO2卧式吸附态M -(CO) -O→Vn ,此吸附态在138℃左右可解离成M -CO和V=O ;CH3OH在Lewis酸位和Lewis碱位协同作用下可形成解离吸附态V -OCH3和V -OH ;CO2 和CH3OH在Cu Ni/VSiO催化剂表面上的反应产物主要为碳酸二甲酯(DMC)、CH2O、CO和H2O ,其生成DMC的选择性在85%以上.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.