Multiwalled carbon nanotube supported PtRu for the anode of direct methanol fuel cells

The activity of the methanol oxidation reaction of a multiwalled carbon nanotube (MWCNT)-supported PtRu catalyst was investigated and compared with the Vulcan XC-72 carbon-supported catalyst. The PtRu nanoparticles with 1:1 and 7:3 atomic ratios (with similar PtRu loadings and morphological structures) were deposited both on the MWCNTs and on the carbon. Cyclicvoltammetry results demonstrated that the MWCNT-supported PtRu catalyst exhibited a higher mass activity (mA mg(-1) of PtRu) for the methanol oxidation reaction than the carbon-supported PtRu under the condition that both catalysts possess more or less the same PtRu loadings, particle sizes, dispersions, and electrochemical surface area. The direct methanol fuel cell performance test data showed that MWCNT-supported PtRu catalysts yielded about 35-39% higher power densities than the carbon-supported PtRu.     

Structural analysis of sonochemically prepared PtRu versus Johnson Matthey PtRu in operating direct methanol fuel cells

Sonochemically prepared PtRu (3 : 1) and Johnson Matthey PtRu (1 : 1) were analyzed by X-ray absorption spectroscopy in operating liquid feed direct methanol fuel cells. The total metal loadings were 4 mg cm(-2) unsupported catalysts at the anode and cathode of the membrane electrode assembly. Ex situ XRD lattice parameter analysis indicates partial segregation of the Ru from the PtRu fcc alloy in both catalysts. A comparison of the in situ DMFC EXAFS to that of the as-received catalyst shows that catalyst restructuring during DMFC operation increases the total metal coordination numbers. A combined analysis of XRD determined grain sizes and lattice parameters, ex situ and in situ EXAFS analysis, and XRF of the as-received catalysts enables determination of the catalyst shell composition. The multi-spectrum analysis shows that the core size increases during DMFC operation by reduction of Pt oxides and incorporation of Pt into the core. This increases the mole fraction of Ru in the catalyst shell structure.     

直接甲醇燃料电池纳米结构电催化材料及多孔电极研究

直接甲醇燃料电池(DMFC)因其燃料能量密度高,工作温度低,低污染排放等优点被认为是用作移动设备电源的最佳选择之一,至今已有美国的Oorja Protonics公司和丹麦的IRD公司等新能源相关企业相继发布了多款用于手机、电脑、通信基站、叉式装卸机或房车的商业产品.然而, DMFC内部的复杂情况造成的多种不同的电压损失仍旧使得其实际电压效率远低于理论值.其中从阳极渗透到阴极的甲醇造成的混合电位导致的电压损失尤为明显.目前,众多研究人员都致力于开发高稳定性、高耐久性、高性能且低成本的催化材料体系,以克服传统Pt催化剂存在的各种问题.除了催化剂本身之外, DMFC的问题还与其中膜电极的微结构和电化学特性息息相关.膜电极是化学能通过电催化氧化还原反应转化为电能的反应场所,通常由阳极扩散层、阳极催化层、质子交换膜、阴极催化层和阴极扩散层依序组合而成.通过对MEA中的各层进行优化,如传质管理和甲醇渗透等问题都能得到有效解决.
　　近年来,纳米技术常被用于改进DMFC性能的研究.具备纳米结构的金属-碳/金属氧化物载体类催化材料得到了广泛研究.这些电催化材料在制备方法、结构和组分上都有较大区别.结构方面,许多研究都证明制备纳米级多孔网络结构或者有序阵列结构的催化层有助于提高催化性能和Pt的利用率.组分方面,许多研究人员都开展了引入Pt以外金属成分或金属氧化物来改变Pt催化剂的表面电子状态的研究.引入这些组分导致的配位体效应可以通过弱化Pt与H+, OH-或COads等的相互作用来起到抗催化毒化和提高催化效率的作用.尽管对于DMFC领域的认知逐渐完善,但是仍有许多问题有待解决.因此,本文介绍了目前用于DMFC的纳米结构电催化材料和多孔电极的研究进展.重点介绍了纳米结构催化剂和载体材料的合成及表征.
　　通过对比不同催化材料的特性可以发现,在本文涉及到的催化材料中, In0.1SnO2-Pt和(MoO3)0.2SnO2-Pt/C表现出了最高的催化活性,但是它们高效催化甲醇电氧化所需的碱性环境与现在占绝对主流地位的Nafion质子交换膜所必须的酸性环境相冲突,所以其实际应用价值在碱性阴离子交换膜研究取得突破前都难以有效发挥.而另一类表现较好的采用溶致液晶模板法合成的纳米树枝状和纳米星形Pt催化剂则存在制备工艺难以商业规模化的问题.总的来说,采用溶剂热合成法制备的Pt-NRCeO2/GNs和Pt/Ti0.9Sn0.1O2-C等纳米结构金属氧化物、碳材料复合载体和Pt基贵金属催化剂组成的催化材料体系不仅催化性能相对于商业化Pt纳米颗粒有很大提高,而且制备方法易于商业规模化,值得进一步关注.此外,本文还介绍了如内部传质过程的理论建模计算和膜电极中功能结构的制备等优化DMFC中多孔电极内传质过程的方法.通过计算机模拟得到优化DMFC内部传质过程所需的扩散层、催化层的传质特性相关参数,再通过改进MEA制备工艺,有效控制各层的结构参数向模拟的优化值靠拢,能够实现DMFC性能的有效提升.综合模拟、实验研究及工艺研究结果,根据实际需要,设计和制备包含新功能层的MEA的相关研究也更进一步提高了DMFC的性能和实用性.就目前的研究情况而言,如果在性能提升的基础上,使用寿命再取得突破, DMFC一定会有很好的商业应用前景.     

Highly ordered mesoporous Nafion membranes for fuel cells

A highly ordered mesoporous Nafion membrane with a remarkable water retention ability was synthesized via a micelle templating method with self-assembled Pluronic F108 surfactants and its capability to operate under completely dry gas streams is demonstrated.     

Aqueous dye adsorption on ordered mesoporous carbons

Ordered mesoporous carbons (OMCs) with varying pore size, and microporous carbon, CFY, were synthesized using ordered mesoporous silica SBA-15 and NaY zeolite as hard templates, respectively. N(2) adsorption tests show that the synthesized OMCs possess abundant mesopores and centralized mesopore distribution. Methylene blue (MB) and neutral red (NR) were used as probe molecules to investigate their adsorption behaviors on OMCs and CFY. As evidenced by adsorption tests, the volume of mesopores of which the pore size is larger than 3.5 nm is a crucial factor for the adsorption capacity and adsorption rate of MB on OMCs. However, the most probable pore diameter of OMCs was found to be vital to the adsorption capacity and adsorption rate of NR. Theoretical studies show that the adsorption kinetics of MB and NR on OMCs can be well depicted by using pseudo-second-order kinetic model.     

Pt and Ru X-ray absorption spectroscopy of PtRu anode catalysts in operating direct methanol fuel cells

In situ X-ray absorption spectroscopy, ex situ X-ray fluorescence, and X-ray powder diffraction enabled detailed core analysis of phase segregated nanostructured PtRu anode catalysts in an operating direct methanol fuel cell (DMFC). No change in the core structures of the phase segregated catalyst was observed as the potential traversed the current onset potential of the DMFC. The methodology was exemplified using a Johnson Matthey unsupported PtRu (1:1) anode catalyst incorporated into a DMFC membrane electrode assembly. During DMFC operation the catalyst is essentially metallic with half of the Ru incorporated into a face-centered cubic (FCC) Pt alloy lattice and the remaining half in an amorphous phase. The extended X-ray absorption fine structure (EXAFS) analysis suggests that the FCC lattice is not fully disordered. The EXAFS indicates that the Ru-O bond lengths were significantly shorter than those reported for Ru-O of ruthenium oxides, suggesting that the phases in which the Ru resides in the catalysts are not similar to oxides.     

Partially graphitized ordered mesoporous carbons for high-rate supercapacitors

Partially graphitized ordered mesoporous carbons have been prepared with a soft template method using low-molecular-weight phenolic resol as a carbon source, triblock copolymer F127 as a template, and ferric citrate as a graphitization catalyst. N₂ sorption and transmission electron microscopy analysis show that the ordered mesoporous carbons have been partially graphitized when the carbonization temperature is above 700 °C. The graphitic ordered mesoporous carbons exhibit better rate performance than amorphous ordered mesoporous carbons. The specific capacitance of the graphitic ordered mesoporous carbons (GOMCs) prepared at 700 °C reaches to 112 F g^?1 at a scan rate of up to 1,000 mV s^?1. Its capacitance retention ratio is 64 %, which is much higher than that of the amorphous ordered mesoporous carbons prepared at 600 °C (33 %). High electronic conductivity and ordered mesoporous structure lead to the high electrochemical performance of the partially graphitized ordered mesoporous carbons.     

PtRu/carbon nanotube nanocomposite synthesized in supercritical fluid: a novel electrocatalyst for direct methanol fuel cells

Platinum/ruthenium nanoparticles were decorated on carbon nanotubes (CNT) in supercritical carbon dioxide, and the nanocomposites were characterized by transmission electron microscopy (TEM) and X-ray diffraction (XRD). TEM images show that the particles size is in the range of 5-10 nm, and XRD patterns show a face-centered cubic crystal structure. Methanol electrooxidation in 1 M sulfuric acid electrolyte containing 2 M methanol were studied onPtRu/CNT (Pt, 4.1 wt%; Ru, 2.3 wt%; molar ratio approximately Pt/Ru = 45:55) catalysts using cyclic voltammetry, linear sweep voltammetry, chronoamperometry, and electrochemical impedance spectroscopy. All the electrochemical results show that PtRu/CNT catalysts exhibit high activity for methanol oxidation which resulted from the high surface area of carbon nanotubes and the nanostructure of platinum/ruthenium particles. Compared with Pt/CNT, the onset potential is much lower and the ratio of forward anodic peak current to reverse anodic peak current is much higher for methanol oxidation, which indicates the higher catalytic activity of PtRu/CNT. The presence of Ru with Pt accelerates the rate of methanol oxidation. The results demonstrated the feasibility of processing bimetallic catalysts in supercritical carbon dioxide for fuel cell applications.     

Capacitive performance of ordered mesoporous carbons with tunable porous texture in ionic liquid electrolytes

Ordered mesoporous carbons with tunable pore size and surface chemical properties are prepared by doping boric acid using a hard-templating method. The capacitive performance of these carbons is investigated in two common ionic liquids of EMImBF₄ and EMImTSFI. As demonstrated by the structure analysis, the pore size increases from 3.3 to 5.7 nm and the content of oxygenated groups on the carbon surface increases from 2.0 to 5.2 mol% with the increase of the boron doping from 0 to 50 mol%. In ionic liquid electrolyte, the carbons mainly show typical electric double layer capacitance, and the capacitance retention ratio and ion diffusion in the carbon channels is determined to the surface chemical property. The prepared carbons present visible pseudo-capacitance due to the rapid redox reactions of the oxygenated groups in hydrophilic EMImBF₄, reflecting by the increasing of the specific surface capacitance, while no visible pseudo-capacitive behavior was observed in hydrophobic EMImTSFI.     

Nanostructured cathodic catalysts for direct methanol fuel cells

The high activity of catalysts based of nanodisperse Pt-P system and their tolerance to the poisoning effect of methanol are demonstrated for the working potentials of cathodes in methanol-air fuel cells. The catalysts’ activity in the oxygen reduction reaction in the presence of methanol is nearly hundred times that of catalysts based on mixed metal-chalcogenide systems.     

Proton-conducting polymer membranes for direct methanol fuel cells

Three methods to block the methanol transport through proton-conducting polymer membranes while maintaining the proton conductivity unchanged have been conducted; 1) selective layer formation on the surface of the membrane, 2) prearation of nanoclay composite membrane providing tortuous pathway of methanol, 3) control and fixation of the proton transport channels. The methanol permeability through the membranes decreased significantly at the expense of the small decrease in the proton conductivity. It is thus concluded that both the structure and the fixation of the proton transport channels are crucial in optimizinging proton conducting membranes for direct methanol fuel cells.     

铂纳米棒有序阵列催化电极在被动式直接甲醇燃料电池中的应用

直接甲醇燃料电池(DMFC)具有能量密度高、无需充电、液体燃料添加便捷及环境友好等优点,是新一代便携式移动电源研究热点. DMFC规模应用的主要技术挑战是如何进一步提高电池性能、显著降低成本和可靠延长寿命.催化电极作为 DMFC发电核心和成本的集中体现,其电催化活性和贵金属用量直接影响 DMFC的性能和成本,开发高性能、低成本的催化电极对推进 DMFC实用化进程具有重要意义.特别是在被动式 DMFC中,阴极催化电极不仅需要提高电催化活性和大幅降低贵金属用量,而且还面临内部严重的“水淹”和氧传质受限等问题.近年来,随着纳米技术发展,有序纳米结构已逐渐应用于 DMFC催化电极的构筑中,电池性能得到显著提高.然而,目前的研究主要集中在膜电极纳米有序微孔层、纳米有序改性膜和纳米有序阳极催化电极及其阳极贵金属载量降低等方面,关于阴极催化电极在有序纳米结构以及载量降低等方面的研究相对较少.
　　本文采用模板法直接在微孔层上电沉积定向生长排列有序、直径可控的铂纳米棒阵列,并作为阴极催化电极应用于被动式 DMFC. X射线衍射和透射电镜结果表明,该铂纳米棒结构稳定,表面含有丰富的纳米晶须结构,有利于催化电极比表面积增加和电催化活性提高.不同催化电极上氧还原的极化曲线表明电极性能依下列次序变化：直径为200 nm铂纳米棒阵列电极>100 nm铂纳米棒阵列电极>商业化铂黑催化电极.电池性能表征表明,长度为1–3μm、直径分别为200和100 nm、载量为1.0 mg/cm2的铂纳米棒阵列作为阴极催化电极的 DMFC最大功率密度分别为17.3和12.0 mW/cm2.通过催化电极电化学活性面积和阻抗测试,分析其性能提高的原因可归结于有序排列的铂纳米棒阵列结构提高了电化学活性面积、增强了氧还原电催化活性并促进了阴极氧的传质.     

Poly(vinylpyrrolidone)-modified graphite carbon nanofibers as promising supports for PtRu catalysts in direct methanol fuel cells

Carbon nanomaterials, including herringbone graphite carbon nanofibers (GNFH), multiwalled carbon nanotubes (MWCNT), and carbon black, were surface-modified by a new poly(vinylpyrrolidone) (PVP) grafting process as well as by the conventional acid-oxidation (AO) process, and characterized by FTIR, TGA, Raman, HRTEM, XRD, and XPS measurements. Pt nanoparticles of 1.8 nm were evenly deposited on all PVP-grafted carbon nanomaterials. The effects of the two surface modification processes on the dispersion, average Pt nanoparticle sizes, the electrocatalytic performance, and electrical conductivities of Pt-carbon nanocomposites in direct methanol oxidation were systematically studied and compared. It was found that the PVP-grafted carbon nanomaterials have much less loss in the electric conductivity and thus better electrocatalytic performance, 17-463% higher, than their corresponding acid oxidation-treated nanocomposites. The electrocatalytic performance of the Pt-carbon nanocomposites decreases in the following order: Pt-PVP-GNFH > Pt-PVP-MWCNTarc > Pt-AO-MWCNTarc > Pt-PVP-MWCNTCVD > Pt-AO-MWCNTCVD > Pt-XC-72R > Pt-AO-GNFH, with the Pt-PVP-GNFH nanocomposite having approximately 270% higher performance than that of the Pt-Vulcan XC-72R nanocomposite. In addition, PtRu-PVP-GNFH shows even better (50% higher) electrocatalytic activity than the Pt-PVP-GNFH nanocomposite at a 0.6 V applied voltage.     

Pervaporation membranes in direct methanol fuel cells

The membranes in direct methanol fuel cells must both conduct protons and serve as a barrier for methanol. Nafion, the most common fuel cell membrane, is an excellent conductor but a poor barrier. Polyvinyl alcohol pervaporation membranes are good methanol barriers but poor conductors. These and most other pervaporation membranes offer no significant advantages over Nafion in methanol fuel cell applications. However, polybenzimidazole membranes have demonstrated characteristics that suggest up to a 15-fold improvement in direct methanol fuel cells. This improvement may be due to an alternate form of proton conduction in which protons travel via a Grotthus or “hopping” mechanism.     

Preparation of activated ordered mesoporous carbons with a channel structure

Activated ordered mesoporous carbons with a channel structure (AOMCs-CS) were successfully prepared by imposing CO(2) activation on ordered mesopore carbon C-FDU-15. It is found that the continuous carbon framework of the precursor C-FDU-15 plays an important role in keeping the order structure of the resulting AOMCs-CS. The mild activation (e.g., 31 wt % burnoff) does not impair the order degree. After that, the order degree gradually decreases with further increasing burnoff. However, the basic hexagonal mesostructure of C-FDU-15 can still be found in the AOMCs-CS when the burnoff is up to 73 wt %, although many carbon walls are punched and thus many larger mesopores and marcropores are generated. With increasing burnoff, the surface area and volume of micropores increase first and then decrease, and the surface area and volume of mesopores continuously increase. The highest measured Brunaruer-Emmett-Teller (BET) surface area, micropore volume, and total pore volume of the AOMCs-CS reach 2004 m(2)/g, 0.50 cm(3)/g, and 1.22 cm(3)/g, respectively.     

Nanostructured PtRu/C as anode catalysts prepared in a pseudomicroemulsion with ionic surfactant for direct methanol fuel cell

Nanostructured PtRu/C catalysts have been prepared from a water-in-oil pseudomicroemulsion with the aqueous phase of a mixed concentrated solution of H(2)PtCl(6), RuCl(3), and carbon powder, oil phase of cyclohexane, ionic surfactant of sodium dodecylbenzene sulfonate (C(18)H(29)NaO(3)S), and cosurfactant n-butanol (C(4)H(10)O). Two different composing PtRu/C nanocatalysts (catalyst 1, Pt 20 wt %, Ru 15 wt %; catalyst 2, Pt 20 wt %, Ru 10 wt %) were synthesized. The catalysts were characterized by transmission electron microscopy, X-ray diffractometry, X-ray photoelectron spectroscopy, and thermogravimetric analysis, and the particles were found to be nanosized (2-4 nm) and inherit the Pt face-centered cubic structure with Pt and Ru mainly in the zero valance oxidation state. The ruthenium oxide and hydrous ruthenium oxide (RuO(x)()H(y)()) were also found in these catalysts. The cyclic voltammograms (CVs) and chronoamperometries for methanol oxidation on these catalysts showed that catalyst 1 with a higher Ru content (15 wt %) has a higher and more durable electrocatalytic activity to methanol oxidation than catalyst 2 with low Ru content (10 wt %). The CV results for catalysts 1 and 2 strongly support the bifunctional mechanism of PtRu/C catalysts for methanol oxidation. The data from direct methanol single cells using these two PtRu/C as anode catalysts show the cell with catalyst 1 has higher open circuit voltage (OCV = 0.75 V) and maximal power density (78 mW/cm(2)) than that with catalyst 2 (OCV = 0.70 V, P(max) = 56 mW/cm(2)) at 80 degrees C.     

Synthesis of PtRu nanoparticles from the hydrosilylation reaction and application as catalyst for direct methanol fuel cell

Nanosized Pt, PtRu, and Ru particles were prepared by a novel process, the hydrosilylation reaction. The hydrosilylation reaction is an effective method of preparation not only for Pt particles but also for other metal colloids, such as Ru. Vulcan XC-72 was selected as catalyst support for Pt, PtRu, and Ru colloids, and TEM investigations showed nanoscale particles and narrow size distribution for both supported and unsupported metals. All Pt and Pt-rich catalysts showed the X-ray diffraction pattern of a face-centered cubic (fcc) crystal structure, whereas the Ru and Ru-rich alloys were more typical of a hexagonal close-packed (hcp) structure. As evidenced by XPS, most Pt and Ru atoms in the nanoparticles were zerovalent, except a trace of oxidation-state metals. The electrooxidation of liquid methanol on these catalysts was investigated at room temperature by cyclic voltammetry and chronoamperometry. The results concluded that some alloy catalysts showed higher catalytic activities and better CO tolerance than the Pt-only catalyst; Pt56Ru44/C have displayed the best electrocatalytic performance among all carbon-supported catalysts.     

直接甲醇燃料电池用PEMs的研究进展

本文介绍了用于直接甲醇燃料电池(DMFCs)的质子交换膜(PEMs)的工作原理与性能要求。讨论了影响DMFCs国PEMs的甲醇渗透性能的因素。综述了Nation、改性Nafion膜以及其它新品种膜的研究进展。