Nanofibrosis of uncrystallizable poly(lactide‐co‐glycolide) via phase separation

Poly(lactide‐co‐glycolide) (PLGA) copolymers are a kind of biocompatible and biodegradable materials being widely used in tissue engineering. However, phase separation had not been reported successfully in fabricating these amorphous polymers into nanofibrous matrix, although this technique had shown advantages over electrospinning in producing a nanofiber network. In this study, tetrahydrofuran (THF)/H₂O solvent pairs were found suitable solvents to induce the formation of uniform PLGA gel at selected gelation temperatures. The results indicated that fine nanofibrous structures with fiber diameter around 40–60 nm could be obtained following the steps of gel formation, solvent extraction, and freeze‐drying, by controlling the concentration of PLGA/THF/H₂O solution, THF/H₂O ratio, and gelation temperature. Copyright © 2009 John Wiley & Sons, Ltd.     

Hyperbranched poly (amine‐ester)‐poly (lactide‐co‐glycolide) copolymer and their nanoparticles as paclitaxel delivery system

A new hyperbranched poly (amine‐ester)‐poly (lactide‐co‐glycolide) copolymer (HPAE‐co‐PLGA) was synthesized by ring‐opening polymerization of D , L ‐lactide (DLLA) glycolid and branched poly (amine‐ester) (HPAE‐OHs) with Sn(Oct)₂ as catalyst. The chemical structures of copolymers were determined by FT‐IR, ¹H‐NMR(¹³C NMR), TGA and their molecular weights were determined by gel permeation chromatography (GPC). Paclitaxel‐loaded copolymer nanoparticles were prepared by the nanoprecipitation method. Their physicochemical characteristics, e.g. morphology and nanoparticles size distribution were then evaluated by means of fluorescence spectroscopy, environmental scanning electron microscopy (ESEM), and dynamic light scattering (DLS). Paclitaxel‐loaded nanoparticles assumed a spherical shape and have unimodal size distribution. It was found that the chemical composition of the nanoparticles was a key factor in controlling nanoparticles size, drug‐loading content, and drug release behavior. As the molar ratio of DL ‐lactide/glycolide to HPAE increased, the nanoparticles size and drug‐loading content increased, and the drug release rate decreased. The antitumor activity of the paclitaxel‐loaded HPAE‐co‐PLGA nanoparticles against human liver cancer H7402 cells was evaluated by 3‐(4, 5‐dimethylthiazol‐2‐yl)‐2,5‐diphenyl tetrazolium bromide (MTT) method. The paclitaxel‐loaded HPAE‐co‐PLGA nanoparticles showed comparable anticancer efficacy with the free drug. Copyright © 2010 John Wiley & Sons, Ltd.     

Biocompatibility evaluation of self‐assembled micelles prepared from poly(lactide‐co‐glycolide)‐poly(ethylene glycol) diblock copolymers

In this work, a series of PLGA‐PEG diblock copolymers were synthesized by ring‐opening polymerization of L‐lactide and glycolide using mPEG as macroinitiator and stannous octoate as catalyst. Spherical micelles were obtained from the various copolymers by using co‐solvent evaporation method. The biocompatibility of micelles was evaluated with the aim of assessing their potential in the development of drug delivery systems. Various aspects of biocompatibility were considered, including MTT assay, agar diffusion test, release of cytokines, hemolytic test, dynamic clotting time, protein adsorption in vitro, and zebrafish embryonic compatibility in vivo. The combined results revealed that the micelles present good cytocompatibility and hemocompatibility in vitro. Moreover, the cumulative effects of micelles throughout embryos developing stages have no toxicity in vivo. It is thus concluded that micelles prepared from PLGA‐PEG copolymers present good biocompatibility as potential drug carrier.     

Fabrication of poly(lactide‐co‐glycolide) scaffold embedded spatially with hydroxyapatite particles on pore walls for bone tissue engineering

Poly(lactide‐co‐glycolide) (PLGA) scaffolds embedded spatially with hydroxyapatite (HA) particles on the pore walls (PLGA/HA‐S) were fabricated by using HA‐coated paraffin spheres as porogens, which were prepared by Pickering emulsion. For comparisons, PLGA scaffolds loaded with same amount of HA particles (2%) in the matrix (PLGA/HA‐M) and pure PLGA scaffolds were prepared by using pure paraffin spheres as porogens. Although the three types of scaffolds had same pore size (450–600 µm) and similar porosity (90%–93%), the PLGA/HA‐S showed the highest compression modulus. The embedment of the HA particles on the pore walls endow the PLGA/HA‐S scaffold with a stronger ability of protein adsorption and mineralization as well as a larger mechanical strength against compression. In vitro culture of rat bone marrow stem cells revealed that cell morphology and proliferation ability were similar on all the scaffolds. However, the alkaline phosphatase activity was significantly improved for the cells cultured on the PLGA/HA‐S scaffolds. Therefore, the method for fabricating scaffolds with spatially embedded nanoparticles provides a new way to obtain the bioactive scaffolds for tissue engineering. Copyright © 2011 John Wiley & Sons, Ltd.     

Synthesis and characterization of poly(vinyl alcohol)‐graft‐[poly(D,L‐lactide)/poly(D,L‐lactide‐co‐glycolide)] hydrogels

Poly(D ,L ‐lactide) and poly(D ,L ‐lactide‐co‐glycolide) with various composition and with one methacrylate and one carboxylate end group were synthesized and grafted onto poly(vinyl alcohol) (PVA) via the carboxylate group. The graft copolymers were crosslinked via the methacrylate groups using a free radical initiator. The polymer networks were characterized by means of NMR and studied qualitatively by means of IR spectroscopy. The influence of the glycolide content in the polyester grafts and of the number of ester units in the grafts on thermal properties and swellability were studied as well. The high swellability in water is characteristic of all hydrogels. Differential scanning calorimetry (DSC) showed a single glass transition temperature that occurs in the range between 51 and 69 °C. Thermogravimetric analysis (TGA) of the networks showed the main loss in weight in the temperature range between 290 and 370 °C. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4536–4544, 2007     

Capillary electrophoresis of bone marrow stromal cells with uptake of heparin‐functionalized poly(lactide‐co‐glycolide) nanoparticles during differentiation towards neurons

This study analyzes the varying electrophoretic mobility and zeta potential of bone marrow stromal cells (BMSCs) during their differentiation towards neurons. Electrophoresis of primary BMSCs and neuron growth factor (NGF)‐induced neuron‐like cells with the uptake of heparin‐functionalized poly(lactide‐co‐glycolide) (PLGA) nanoparticles (NPs) are also investigated. Immunofluorescent images revealed that a high concentration of NGF accelerated the differentiation of BMSCs into neurons. When the concentration of NGF increased, the absolute values of electrophoretic mobility and zeta potential of the differentiating BMSCs increased. In addition, a longer inductive period yielded higher charge of the differentiating BMSCs and a smaller uptake amount of heparin‐functionalized PLGA NPs. However, an increase in the loading efficiency of heparin on PLGA NPs enhanced the uptake and reduced the electrical characteristics of the primary and differentiating BMSCs. Hence, a general rule is drawn that an increase in the uptake of heparin‐functionalized PLGA NPs decreased the electrophoretic mobility and zeta potential of BMSCs during differentiation towards neurons.     

Relationship among drug delivery behavior,degradation behavior and morphology of copolylactones derived from glycolide,l‐lactide and ε‐caprolactone

A series of copolylactones was synthesized by ring‐opening copolymerization of glycolide, L ‐lactide and ?‐caprolactone, using stannous octoate as catalyst. The in vitro degradation behaviors of them were studied and data demonstrated different degradation rates which mainly depended on the compositions. Investigation of the 5‐fluorouracil (5‐Fu) release from these copolylactones revealed that the composition, degradation rate and the morphology of the polymeric matrix played an important role on the drug release kinetics. A sustained 5‐Fu release without initial time lag was obtained from random poly(lactide‐co‐glycolide‐co‐caprolactone) (r‐PGLC) drug carrier, and it differed from the cases of polylactide (PLA) or random poly(lactide‐co‐glycolide) (PLGA), which usually showed an initial time lag or biphasic drug release behavior. It was due to the low glass transition temperature (T _g) of the r‐PGLC and the drug would diffuse faster in rubbery state under the experimental temperature. Furthermore, a significant change in the drug release behavior of r‐PGLC was observed when the temperatures were changed around the T _g of the drug carrier, which implied that the drug release behavior could be regulated by adjusting the morphology of the drug carrier. Copyright © 2002 John Wiley & Sons, Ltd.     

Biodegradable poly(trimethylene carbonate‐b‐(L‐lactide‐ran‐glycolide)) terpolymers with tailored molecular structure and advanced performance

The macroinitiator of poly(1,3‐trimethylene carbonate) (PTMC) with number‐average molecular weight ( ) of 9.6 × 10³ g mol⁻¹ was synthesized by ring‐opening polymerization at 120°C. Then, the novel terpolymer P(TMC‐b‐(LLA‐ran‐GA)) consisting of PTMC homopolymer segment attached with various monomer molar ratios of L‐lactide (LLA) and glycolide (GA) random copolymerization block was prepared with about 5.0 × 10⁴ g mol⁻¹ by ring‐opening polymerization in bulk at 140°C. The tailored molecular structures of P(TMC‐b‐(LLA‐ran‐GA)) were characterized by ¹H nuclear magnetic resonance, ¹³C NMR, FTIR, and gel permeation chromatography, and chain microstructure analysis was performed in detail with ¹³C NMR spectroscopy. The effect of GA units on the thermal and crystallization behaviors, mechanical properties, as well as biodegradability of terpolymers was investigated by differential scanning calorimetry, wide‐angle X‐ray diffraction, stress‐strain measurements, and in vitro tests in comparison with corresponding poly(trimethylene carbonate‐block‐L‐lactide) copolymer P(TMC‐b‐LLA). The results show that amorphous PTMC segments have a significant effect on condensed state behavior of the terpolymers, and the incorporation of GA units strongly decreases the crystallinity and crystallization ability of LLA segment within terpolymers because of more random LLA‐GA sequence and shorter average LLA block length. Meanwhile, the toughness of materials is greatly improved, and in vitro degradation is also accelerated. Peripheral vascular stents were 3D printed for the first time and met the requirements for application. The results show totally biodegradable terpolymers with unique molecular structure, and modifiable properties are promising new biomaterials with advanced performance for biomedical application.     

Stabilizer‐Free Poly(lactide‐co‐glycolide) Nanoparticles Conjugated with Quantum Dots as a Potential Carrier Applied in Human Mesenchymal Stem Cells

We report that human mesenchymal stem cells (hMSCs) were successfully labeled with poly(lactide‐co‐glycolide) nanoparticles (PLGA NPs) surface‐conjugated quantum dots (QDs) (PLGA‐QD NPs) via endocytosis pathway. These NPs were not toxicity even treated with PLGA‐QD NPs at high concentrations for at least four weeks. Besides, PLGA‐QD NPs‐labeled hMSCs did not change their proliferation and differentiation capability toward the cell fates of adipocytes, osteocytes, and chrondrocytes. It's known that PLGA has been widely employed to act as delivery carrier which encapsulates drugs and releases them under a controlled way. Currently, we have also demonstrated that FITC‐loaded PLGA‐QD NPs degraded in hMSCs to achieve intracellular release of FITC. The aim of this research is to investigate viability, proliferation and differentiation capability and the potential for gene delivery of MSCs labeled with PLGA‐QD NPs. In addition to PLGA‐QD NPs, QDs alone were used to serve as a control set for comparison.     

Composites of poly(L‐lactide‐trimethylene carbonate‐glycolide) and surface modified SBA‐15 as bone repair material

This work aims to develop novel composites from a poly(L ‐lactide‐co‐trimethylene carbonate‐co‐glycolide) (PLTG) terpolymer and mesoporous silica (SBA‐15) nanofillers surface modified by post‐synthetic functionalization. SBA‐15 first reacts with a silane coupling agent, γ‐aminopropyl‐trimethoxysilane to introduce ammonium group. PLLA chains were then grafted on the surface of SBA‐15 through ammonium initiated ring‐opening polymerization of L ‐lactide. Composites were prepared via solution mixing of PLTG terpolymer and surface modified SBA‐15. The structures and properties of pure SBA‐15, γ‐aminopropyl‐trimethoxysilane modified SBA‐15 (H₂N‐SBA‐15), PLLA modified SBA‐15 (PLLA‐NH‐SBA‐15), and PLTG/PLLA‐NH‐SBA‐15 composites were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, X‐ray diffraction, scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, transmission electron microscopy, N₂ adsorption‐desorption, differential scanning calorimetry, contact angle measurement, and mechanical testing. The results demonstrated that PLLA chains were successfully grafted onto the surface of SBA‐15 with grafting amounts up to 16 wt.%. The PLTG/PLLA‐NH‐SBA‐15 composites exhibit good mechanical properties. The tensile strength, Young's modulus, and elongation at break of the composite containing 5 wt.% of PLLA‐NH‐SBA‐15 were 39.9 MPa, 1.3 GPa, and 273.6%, respectively, which were all higher than those of neat PLTG or of the composite containing 5 wt.% of pure SBA‐15. Cytocompatibility tests showed that the composites present very low cytotoxicity.     

Mechanical properties and degradation studies of poly(D,L‐lactide‐co‐glycolide) 50:50/graphene oxide nanocomposite films

Poly(D,L‐lactide‐co‐glycolide) 50:50 (PLGA)/graphene oxide (GO) nanocomposite films were prepared with various GO weight fractions. A significant enhancement of mechanical properties of the PLGA/GO nanocomposite films was obtained with GO weight fractions. The incorporation of only 5 wt% of GO resulted in an ~2.5‐fold and ~4.7‐fold increase in the tensile strength and Young's modulus of PLGA, respectively. The thermomechanical behaviors of composite films were investigated by dynamic mechanical analysis. Results indicated that the values of T_g and storage moduli of the PLGA/GO composites were higher than those of the pristine PLGA. The improvement in oxygen barrier properties of composites was presumably attributed to the filler effect of the randomly dispersed GO throughout the PLGA matrix. In this work, we also studied in vitro biodegradation behavior. PLGA/GO composite films were hydrolyzed at 37°C for periods up to 49 days. Because of the presence of GO nanosheets, degradation of composite films took place more slowly with increasing GO amounts. Copyright © 2013 John Wiley & Sons, Ltd.     

Paclitaxel‐Loaded Stabilizer‐Free Poly(D,L‐lactide‐co‐glycolide) Nanoparticles Conjugated with Quantum Dots for Reversion of Anti‐Cancer Drug Resistance and Cancer Cellular Imaging

We prepared the PLGA‐loaded anti‐cancer drug and coated it with quantum dots to make it a dual‐function nanoparticles, and analyzed its potential use in cellular imaging and curing cancers. Two cancer cell lines, paclitaxel‐sensitive KB and paclitaxel‐resistant KB paclitaxel‐50 cervical carcinoma cells, were the relativistic models for analysis of the cytotoxicity of free paclitaxel and paclitaxel‐loaded PLGA conjugated with quantum‐dot nanoparticles. The paclitaxel‐loaded PLGA conjugated with quantum dots nanoparticles were significantly more cytotoxic than the free paclitaxel drug in paclitaxel‐resistant KB paclitaxel‐50 cells. This might have been because the cancer cells developed multi‐drug resistance (MDR), which hampered the action of free paclitaxel by pumping its molecules to extracellular areas. Addition of verapamil, a P‐glycoprotein inhibitor, reversed the MDR mechanism and significantly reduced KB paclitaxel‐50 cell viability. As a result, KB paclitaxel‐50 was highly associated with MDR on the cell membrane. The cytotoxicity results indicated that PLGA nanoparticles served as drug carriers and protected the drugs from MDR‐accelerated efflux. Combined quantum dots with PLGA nanoparticles allowed additional functionality for cellular imaging.     

Thermosensitive polylactide‐glycolide delivery systems for treatment of narcotic addictions

Environmental switches may be fabricated for the controlled release of pharmaceutical drug using a thermally responsive polymer with the intrinsic chemical and physical nature of stimuli‐sensitive smart materials. Particularly, much attention has been paid to the biomedical applications of poly(N‐isopropyl acrylamide) (PNIPAAm) because of its unique reversible transition at a specific lower critical solution temperature (LCST).Thermally sensitive block copolymers, poly(N‐isopropyl acrylamide‐b‐poly(L ‐lactide‐co‐glycolide) (PNIPAAm‐b‐PLGA), and polyethylene glycol‐poly (lactide‐co‐glycolide) (PEG‐PLGA) triblock copolymers with different compositions and length of PLGA block were synthesized via ring‐opening polymerization of lactide and glycolide in the presence of OH‐terminated PNIPAAm or PEG. The composition and structure of the polymer were determined by NMR and FTIR. The effect of important factors, such as ionic strength, pH, and polymer concentration on the phase transition behavior of temperature‐sensitive polymers, were investigated by cloud point measurements. The resulting thermosensitive polymers were used for the entrapment of a narcotic antagonist drug, naltrexone, as the model drug. The loading efficiency and drug release behavior of naltrexone‐loaded hydrogels were investigated. The naltrexone loaded thermosensitive polymers were able to sustain the release of naltrexone for different periods of time, depending on the polymer composition, and concentration. In vitro release studies showed that these thermosensitive polymers are able to deliver naltrexone in biologically active forms at a controlled rate for 3–8 weeks. Copyright © 2009 John Wiley & Sons, Ltd.     

Emulsion copolymerization of D,L‐lactide and glycolide in supercritical carbon dioxide

Biodegradable polyesters were synthesized via an emulsion polymerization in supercritical carbon dioxide (SC‐CO₂). Copolymers of lactide and glycolide were synthesized in SC‐CO₂ with stannous octoate as the ring‐opening catalyst and a fluorocarbon polymer surfactant as an emulsifying agent. The conversion of lactide and glycolide was monitored with respect to the reaction time and temperature with ¹H NMR spectroscopy. The conversion of glycolide surpassed 99% within 72 h for an SC‐CO₂ phase maintained at 200 bar and 70 °C. Under the same conditions, lactide conversion reached 65% after 72 h of polymerization. Unpolymerized monomer was removed after the reaction by extraction with an SC‐CO₂ mobile phase. The molecular weights of all the copolymers were measured by gel permeation chromatography. Weight‐average molecular weights (M_w) ranged between 2500 and 30,200 g/mol and polydispersity indices ranged from 1.4 to 2.3 for polymerization times of 6 and 48 h, respectively. Although the molecular weight increased significantly during the first 48 h of reaction, there was no significant difference in the M_w for polymerization times of 48 and 72 h. Emulsion polymerization within the benign solvent SC‐CO₂ demonstrated improved conversion and molecular weight versus polymers synthesized without surfactant. The emulsion polymerization of lactide and glycolide copolymers in SC‐CO₂ is proposed as a novel production technique for high‐purity, biodegradable polymers. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 562–570, 2001     

Water‐disintegrative and biodegradable blends containing poly(L‐lactic acid) and poly(butylene adipate‐co‐terephthalate)

In this study, novel biodegradable materials were successfully generated, which have excellent mechanical properties in air during usage and storage, but whose structure easily disintegrates when immersed in water. The materials were prepared by melt blending poly(L ‐lactic acid) (PLLA) and poly(butylene adipate‐co‐terephthalate) (PBAT) with a small amount of oligomeric poly(aspartic acid‐co‐lactide) (PAL) as a degradation accelerator. The degradation behavior of the blends was investigated by immersing the blend films in phosphate‐buffered saline (pH = 7.3) at 40 °C. It was shown that the PAL content and composition significantly affected morphology, mechanical properties, and hydrolysis rate of the blends. It was observed that the blends containing PAL with higher molar ratios of L ‐lactyl [LA]/[Asp] had smaller PBAT domain size, showing better mechanical properties when compared with those containing PAL with lower molar ratios of [LA]/[Asp]. The degradation rates of both PLLA and PBAT components in the ternary blends simultaneously became higher for the blends containing PAL with higher molar ratios of [LA]/[Asp]. It was confirmed that the PLLA component and its decomposed materials efficiently catalyze the hydrolytic degradation of the PBAT component, but by contrast that the PBAT component and its decomposed materials do not catalyze the hydrolytic degradation of the PLLA component in the blends. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Morphology and thermal properties of poly(L‐lactide)/poly(butylene succinate‐co‐butylene adipate) compounded with twice functionalized clay

Poly(L ‐lactide) (PLLA)/poly(butylene succinate‐co‐butylene adipate) (PBSA) blends were compounded with Cloisite 25A® (C25A) and C25A functionalized with epoxy groups, respectively. Epoxy groups on the surface of C25A were introduced by treating C25A with (glycidoxypropyl)trimethoxy silane (GPS) to produce so called Twice Functionalized Organoclay (TFC). Variation of morphology and properties of PLLA/PBSA/C25A composites was investigated before and after the treatment with GPS. The morphological structure of the composites was analyzed by using X‐ray diffractometry (XRD) and transmission electron microscopy (TEM). The silicate layers of PLLA/PBSA/TFC were exfoliated to a larger extent than PLLA/PBSA/C25A. Incorporation of the epoxy groups on C25A improved significantly elongation at break as well as tensile modulus and tensile strength of PLLA/PBSA/C25A. The larger amount of exfoliation of the silicate layers in PLLA/PBSA/TFC as compared with that in PLLA/PBSA/C25A was attributed to the increased interfacial interaction between the polyesters and the clay due to chemical reaction. Thermo gravimetric analysis revealed that both T_5%, which was the temperature corresponding to 5% weight loss, and activation energy of thermal decomposition of PLLA/PBSA/TFC were far superior to those of PLLA/PBSA/C25A as well as to those of PLLA/PBSA, indicating that the composites with exfoliated silicate layers were more thermally stable than those with intercalated silicate layers. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 478–487, 2005     

Synthesis and non‐isothermal crystallization kinetics of poly(ethylene terephthalate)‐co‐poly(propylene glycol) copolymers

Poly(ethylene terephthalate)‐co‐poly(propylene glycol) (PET‐co‐PPG) copolymers with PPG ratio ranging from 0 to 0.90 mol% were synthesized by the melt copolycondensation. The intrinsic viscosity, structure, non‐isothermal crystallization behavior, nucleation and spherulitic growth of the copolymers were investigated by Ubbelohde viscometer, Proton Nuclear Magnetic Resonance (¹H‐NMR), differential scanning calorimetry, and polarized optical microscopy, respectively. The non‐isothermal crystallization process of the copolymers was analyzed by Avrami, Ozawa, Mo's, Kissinger, and Dobreva methods, respectively. The results showed that the crystallizability of PET was apparently enhanced with incorporating a small amount of PPG, which first rose and then reduced with increasing amount of PPG in the copolymers at a given cooling rate. The crystallization mechanism was a three‐dimensional growth with both instantaneous and sporadic nucleation. Particularly, PET‐co‐PPG containing 0.60 mol% PPG exhibited the highest crystallizability among all the copolymers. Copyright © 2015 John Wiley & Sons, Ltd.     

Monodisperse Poly(lactide‐co‐glycolic acid)‐Based Nanocarriers for Gene Transfection

This contribution describes a simple, aerosol‐based method for fabricating monodisperse particles containing mixtures of poly(lactide‐co‐glycolic acid) [PLGA], protamine sulfate (Prot), and poly(l‐ lysine) [PLL] as nanocarriers for gene transfection. Aqueous solutions of PLGA, Prot, and PLL were collison‐atomized, and the resulting aerosolized droplets were dried “on the fly” to form solid particles, which then were electrostatically size‐classified into 50, 100, and 200 nm mobility diameter samples. Measurements of cell viability and transfection reveal that the fabricated nanocarriers have a lower cytotoxicity (>85% in cell viability) and a higher transfection efficiency [>8.7 × 10⁵ in relative light units (RLU) mg⁻¹] than does 25 kDa polyethyleneimine (≈50% and 6.8 × 10⁵ RLU mg⁻¹).     

Two‐dimensional Fourier transform infrared spectroscopy study of biosynthesized poly(hydroxybutyrate‐co‐hydroxyhexanoate) and poly(hydroxybutyrate‐ co‐hydroxyvalerate)

Generalized two‐dimensional (2D) Fourier transform infrared correlation spectroscopy was used to investigate the effect of the comonomer compositions on the crystallization behavior of two types of biosynthesized random copolymers, poly(hydroxybutyrate‐co‐hydroxyhexanoate) and poly(hydroxybutyrate‐co‐hydroxyvalerate). The carbonyl absorption band around 1730 cm^?1 was sensitive to the degree of crystallinity. 2D correlation analysis demonstrated that the 3‐hydroxyhexanoate units preferred to remain in the amorphous phase of the semicrystalline poly(hydroxybutyrate‐co‐hydroxyhexanoate) copolymer, resulting in decreases in the degree of crystallinity and the rate of the crystallization process. The poly(hydroxybutyrate‐co‐hydroxyvalerate) copolymer maintained a high degree of crystallinity when the 3‐hydroxyvalerate fraction was increased from 0 to 25 mol % because of isodimorphism. The crystalline and amorphous absorption bands for the carbonyl bond for this copolymer, therefore, changed simultaneously. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 649–656, 2002; DOI 10.1002/polb.10126