首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
Dynamic mechanical properties of chlorinated butyl rubber blends   总被引:1,自引:0,他引:1  
The binary blends are prepared by chlorinated butyl rubber (CIIR) and 3,9-bis[1,1-dimethyl-2{β-(3-tert-butyl-4-hydroxy-5-methylphenyl)propionyloxy}ethyl]-2, 4, 8,10-tetraoxaspiro[5,5]-undecane (AO-80), which are investigated by dynamic mechanical analysis and thermal analysis. It is shown that CIIR/AO-80 blends clearly exhibit two kinds of relaxations, which are attributed to the relaxation of CIIR-rich matrix and AO-80-rich domains, respectively, and attenuated total reflection (ATR)-FTIR spectrum indicates that the existence of intermolecular hydrogen bonds between AO-80 and CIIR. When AO-80 is replaced by petroleum resins, only one loss peak appears, and the position of it is related to the softening point and the content of the petroleum resin. In order to regulate the damping property of CIIR/petroleum resin blend, the ternary blend of CIIR/petroleum resin/AO-80/is prepared and a second peak appears at higher temperature indicating that a good damping material is obtained.  相似文献   

2.
Nitrile–butadiene rubber (NBR) has been blended with polychloroprene (CR) in a weight ratio of 1:1. The vulcanizing systems in the blend formulations were varied to obtain non crosslinked CR embedded in vulcanized NBR and non crosslinked NBR embedded in vulcanized CR. The effects of these two different phases on the rheological and mechanical characteristics were evaluated. In addition, the dynamic compliance of the blends was measured over wide ranges of frequency and temperature. It has been found that the mechanical and rheological properties of the vulcanized blends depend on the type of vulcanizing system, its concentration and the presence of reinforcing filler. The mechanical properties of the blend containing N‐cyclohexyl‐2‐benzthiazyl sulphenamide/S as vulcanizing system suitable for NBR are higher than those of the blend containing non‐sulfur vulcanizing system (Zno/Mgo and ethylene thiourea) suitable for CR. Both types of rubber (CR and NBR) in the blend are incompatible as two glass transition temperatures have been observed. Copyright © 2000 John Wiley & Sons, Ltd.  相似文献   

3.
氯化丁基橡胶/聚(甲基)丙烯酸酯共混物阻尼性能研究   总被引:6,自引:0,他引:6  
制备了一系列氯化丁基橡胶 (CIIR) 聚 (甲基 )丙烯酸酯 (PMAc)共混复合物 .DMA ,DSC对这些共混物的研究表明 ,无论是共交联体系还是非共交联体系 ,CIIR PMAc共混物均能将CIIR有效阻尼功能区移向高温 ;FTIR分析及抽提实验证明了前一体系CIIR PMAc共混物中共交联结构的存在 ;TEM研究发现 ,共交联改变了CIIR PMAc共混物的微观形貌 .研究结果表明 ,不同组成和结构的PMAc的引入 ,导致共混物中CIIR的Tll转变和Tg 转变受到不同程度的抑制 ,因此引起由共交联体系和非共交联体系制得的CIIR PMAc共混物显示出不同的阻尼行为 .  相似文献   

4.
The dynamic mechanical behavior of uncrosslinked (thermoplastic) and crosslinked (thermosetting) acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) (NBR/EVA) blends was studied with reference to the effect of blend ratio, crosslinking systems, frequency, and temperature. Different crosslinked systems were prepared using peroxide (DCP), sulfur, and mixed crosslink systems. The glass‐transition behavior of the blends was affected by the blend ratio, the nature of crosslinking, and frequency. sThe damping properties of the blends increased with NBR content. The variations in tan δmax were in accordance with morphology changes in the blends. From tan δ values of peroxide‐cured NBR, EVA, and blends the crosslinking effect of DCP was more predominant in NBR. The morphology of the uncrosslinked blends was examined using scanning electron and optical microscopes. Cocontinuous morphology was observed between 40 and 60 wt % of NBR. The particle size distribution curve of the blends was also drawn. The Arrhenius relationship was used to calculate the activation energy for the glass transition of the blends, and it decreased with an increase in the NBR content. Various theoretical models were used to predict the modulus of the blends. From wide‐angle X‐ray scattering studies, the degree of crystallinity of the blends decreased with an increasing NBR content. The thermal behavior of the uncrosslinked and crosslinked systems of NBR/EVA blends was analyzed using a differential scanning calorimeter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1556–1570, 2002  相似文献   

5.

Blends of nitrile butadiene rubber (NBR) with butadiene rubber (BR) with varying ratios have been prepared. Vulcanization of prepared blends has been induced by ionizing radiation of gamma rays with varying dose up to 250 kGy. Physical properties, namely soluble fraction and swelling number have been followed up using toluene as a solvent. Mechanical properties, namely tensile strength, tensile modulus at 100% elongation and elongation at break have been followed up as a function of irradiation dose, as well as blend composition. Thermal stability of blends was studied by TGA. The result indicated that the addition of NBR has improved the properties of NBR/BR blends. Also, NBR/BR blend is thermally stable than BR alone.  相似文献   

6.
Effects of precipitated silica (PSi) and silica from fly ash (FA) particles (FASi) on the cure and mechanical properties before and after thermal and oil aging of natural rubber (NR) and acrylonitrile–butadiene rubber (NBR) blends with and without chloroprene rubber (CR) or epoxidized NR (ENR) as a compatibilizer have been reported in this paper. The experimental results suggested that the scorch and cure times decreased with the addition of silica and the compound viscosity increased on increasing the silica content. The mechanical properties for PSi filled NR/NBR vulcanizates were greater than those for FASi filled NR/NBR vulcanizates in all cases. The PSi could be used for reinforcing the NR/NBR vulcanizates while the silica from FA was regarded as a semi‐reinforcing and/or extending filler. The incorporation of CR or ENR enhanced the mechanical properties of the NR/NBR vulcanizates, the ENR being more effective and compatible with the blend. The mechanical properties of the NR/NBR vulcanizates were improved by post‐curing effect from thermal aging but deteriorated by the oil aging. Copyright © 2008 John Wiley & Sons, Ltd.  相似文献   

7.
Blends of poly(vinylidene fluoride) (PVDF), silicone rubber (SR) and flurorubber (FKM) were prepared via peroxide dynamic vulcanization. The effect of FKM loading on the morphology, mechanical properties, crystallization behavior, rheology and dynamic mechanical properties of the PVDF/SR/FKM ternary blends was investigated. A “network” was observed in the PVDF/SR binary blends, which disappeared in the ternary blends, but a core-shell-like structure was formed. The mechanical properties were significantly improved. The Izod impact strength of PVDF/SR/FKM blend with 19 wt% FKM was 18.3 kJ/m2, which was 3–4 times higher than the PVDF/SR binary blend. The complex viscosity and storage modulus of the PVDF/SR/FKM blends decreased with increasing FKM content, hence the processability was improved. The increase of FKM content seemed to show a favorable effect on the crystallization of the PVDF component. It promoted the nucleation process of PVDF, leading to increased polymer crystallization rate and higher crystallization temperature. The glass-rubber transition temperature of the PVDF phase moved to a lower temperature.  相似文献   

8.
Epoxidized natural rubber (ENR) and thermoplastic polyurethane (TPU) blends were prepared by simple blend and dynamic vulcanization. The main objective was to prepare a low‐hardness TPU material with good damping and elastic and mechanical properties. It was found that the incorporation of ENR into the blend shows a reduction in Young's modulus, hardness (i.e. <70 Shore A), damping properties (i.e. tan δ < 0.3), and tension set (i.e. <20%) compared with the pure TPU. This indicates the formation of softer TPU materials with superior damping and elastomeric properties. However, incorporation of ENR sacrificed mechanical properties in terms of tensile strength and elongation at break, but these still remain in the range of applicability for industrial uses. It was also found that dynamic vulcanization caused enhancement of mechanical properties, relaxation, damping, rheological properties, and elasticity of the blends. Temperature scanning stress relaxation measurements revealed an improvement in stress relaxation properties and thermal resistance of the dynamically cured ENR/TPU blend. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

9.
Damping performance of Eucommia ulmoides gum   总被引:1,自引:0,他引:1  
薛兆弘 《高分子科学》2011,29(2):157-163
Eucommia ulmoides gum(EU gum),known as gutta percha in Southeast Asia,is a natural polymer with double characteristics of rubber and plastic.In present paper,tanδ-T curve and hysteresis loss(HL) were chosen to characterize its damping property.The results indicated that its tanδvalue would increase with rising of temperature when T>0℃and form another damping peak at 40-80℃besides T_g peak.This phenomenon resulted from meltage of crystals of EU gum could increase its damping property at ambient-high temperature.Its tanδvalue even exceeded those of conventional damping rubbers,such as nitrile-butadiene rubber(NBR) and chlorinated isobutene-isoprene rubber(CIIR).  相似文献   

10.
In comparison with normal damping rubbers such as natural rubber (NR), styrene butadiene rubber (SBR), isobutylene isoprene rubber (IIR) etc., Mo-based high vinyl polybutadiene rubber (HVBR) with high loss factor, excellent aging resistance and glass transition temperature closer to room temperature, is a promising damping material. The effective damping temperature range of HVBR could be further broadened by blending with ethylene-vinyl acetate (EVM) and the effects of blending methods (in situ polymerization blending or mechanical blending) and blending ratios on the damping properties and physical properties of HVBR/EVM blended rubber were studied. HVBR/EVM in situ polymerization blends was prepared by butadiene coordination polymerization by Mo-base catalyst in a toluene solution of EVM. The results of dynamic mechanical analysis (DMA) and scanning electron microscopy (SEM) of the blended vulcanizates via in situ polymerization blending revealed that the compatibility between HVBR and EVM was improved compared with that of the blended vulcanizates via the traditional mechanical blending method. The two phases of HVBR/EVM in situ polymerization blends had good dispersion and uniformity, the damping temperature range was significantly expanded, and the peak and valley of the damping temperature range were greatly improved. A blending ratio of HVBR/EVM900 = 100/40 showed the best damping properties and the effective damping temperature range (tanδ>0.3) was extended from −6.6 °C to 39.4 °C.  相似文献   

11.
Methyl‐methacrylate‐grafted natural rubber was prepared by free radical polymerization of methyl methacrylate in natural rubber latex, and their structure and dynamics were investigated by dynamic mechanical analysis and solid‐state nuclear magnetic resonance (NMR). Samples were prepared by chemical initiation and high‐energy radiation. The changes of glass transition temperature and tan δ max with different total poly(methyl methacrylate (PMMA) content are reported. The effect of the change in composition in copolymers on tan δ peak width, tan δ max, and area under the tan δ curve are used to understand the miscibility and damping properties. Solid‐state 13C‐NMR measurements were carried out to determine several relaxation time parameters, such as rotating frame and laboratory frame proton and carbon relaxation times. Cross polarization times and carbon relaxation times were interpreted based on the changes in the molecular motion. Proton relaxation times were interpreted based on the heterogeneity of the matrix. Results confirmed phase separation and a presence of an interfacial region. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1141–1153, 1999  相似文献   

12.
The present study deals with the structure–property relationship of organoclay (OC) filled nanocomposites based on rubber blend comprising of nitrile‐butadiene rubber (NBR) and phenolic resin (PH). To obtain a better insight into the characteristics of the NBR/PH/OC hybrid system, a simple model system consisting of NBR/OC nanocomposites is also taken into consideration. A series of NBR/OC and NBR/PH/OC nanocomposites containing a wide range of OC concentrations (2.5–30 phr) are prepared by using traditional open two‐roll mill. Structural analysis performed by X‐ray diffraction (XRD), scanning electron microscope (SEM), and transmission electron microscope (TEM) exhibits mixed exfoliated and intercalated morphology at low OC content, below 7.5 phr, and a well‐ordered intercalated morphology at higher OC loading. It is shown that the dispersion of OC is also influenced by mixing time and order of mixing of components. Analysis of the cure characteristics, mechanical, and thermal properties of both the NBR/OC and NBR/PH/OC nanocomposites reveals that the OC is dispersed mainly in the NBR continuous phase, even though some is likely localized in the rubber–resin interface. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

13.
The properties of chlorosulphonated polyethylene (CSM) rubber, acrylonitrile rubber (NBR) and their blend (50/50 w/w) were studied. Fourier transform infrared (FTIR) studies supported that CSM/NBR rubber blend is self curable, when cross-linking takes place between acrylonitrile groups of NBR and –SO2Cl groups or in situ generated allyl chloride moieties of CSM. The thermal stability of vulcanizates was analyzed in nitrogen by thermogravimetry. It was found that the initial degradation temperature of elastomer based on CSM rubber is lower than of pure NBR rubber. By adding NBR to CSM rubbers, the degradation temperature of crosslinked material increased, indicating higher thermal stability. The activation energy for the degradation are determined using the Arrhenius equation The activation energies for the rubber blends are higher than for elastomers based on pure rubbers. It was found that the mass loss of the blends at any temperature was between those of the pure rubbers. The differential scanning calorimetry (DSC) was used for the glass transition temperature determination. It is estimated thermodynamic immiscibility of NBR/CSM blend based on noticed two different glass transition temperatures, corresponding to CSM and NBR rubbers.  相似文献   

14.
The viscoelastic properties of binary blends of nitrile rubber (NBR) and isotactic polypropylene (PP) of different compositions have been calculated with mean‐field theories developed by Kerner. The phase morphology and geometry have been assumed, and experimental data for the component polymers over a wide temperature range have been used. Hashin's elastic–viscoelastic analogy principle is used in applying Kerner's theory of elastic systems for viscoelastic materials, namely, polymer blends. The two theoretical models used are the discrete particle model (which assumes one component as dispersed inclusions in the matrix of the other) and the polyaggregate model (in which no matrix phase but a cocontinuous structure of the two is postulated). A solution method for the coupled equations of the polyaggregate model, considering Poisson's ratio as a complex parameter, is deduced. The viscoelastic properties are determined in terms of the small‐strain dynamic storage modulus and loss tangent with a Rheovibron DDV viscoelastometer for the blends and the component polymers. Theoretical calculations are compared with the experimental small‐strain dynamic mechanical properties of the blends and their morphological characterizations. Predictions are also compared with the experimental mechanical properties of compatibilized and dynamically cured 70/30 PP/NBR blends. The results computed with the discrete particle model with PP as the matrix compare well with the experimental results for 30/70, 70/30, and 50/50 PP/NBR blends. For 70/30 and 50/50 blends, these predictions are supported by scanning electron microscopy (SEM) investigations. However, for 30/70 blends, the predictions are not in agreement with SEM results, which reveal a cocontinuous blend of the two. Predictions of the discrete particle model are poor with NBR as the matrix for all three volume fractions. A closer agreement of the predicted results for a 70/30 PP/NBR blend and the properties of a 1% maleic anhydride modified PP or 3% phenolic‐modified PP compatibilized 70/30 PP/NBR blend in the lower temperature zone has been observed. This may be explained by improved interfacial adhesion and stable phase morphology. A mixed‐cure dynamically vulcanized system gave a better agreement with the predictions with PP as the matrix than the peroxide, sulfur, and unvulcanized systems. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1417–1432, 2004  相似文献   

15.
Mechanical properties of two dual-phase polymer electrolytes (DPEs), prepared from poly(styrene-co-butadiene) rubber (SBR) and poly(acrylonitrile-co-butadiene) rubber (NBR) latices, are studied. Both DPEs are composed of an SBR supporting phase and an ionconductive phase of NBR/lithium salt solution. The first DPE maintains a tensile strength of 0.5 MPa and elongation of 280% with an ionic conductivity of 10?3 S/cm. Although the glass transition relaxations based on the dual-phase structure are not resolved in this DPE because of the proximity of the glass transition temperatures of the SBR and NBR, the glass transition shifts to a lower temperature due to the plasticization by the lithium salt solution. In the second DPE, two distinctive glass transition relaxations, corresponding to the SBR and NBR phases, are observed in the viscoelasticity versus temperature measurement, indicating the dual-phase structure. A simple equivalent mechanical model, which is modified from the Takayanagi model, is introduced to elucidate the mechanical behavior of the dual-phase structure in the second DPE. According to this model, 8% of DPE is a mechanically continuous SBR phase in the tensile direction, which effectively gives mechanical support to the DPE. © 1995 John Wiley & Sons, Inc.  相似文献   

16.
PPC/NBR弹性体的结构与性能   总被引:2,自引:3,他引:2  
本文研究了聚丙撑碳酸酯(PPC)/丁腈橡胶(NBR)弹性体结构形态、动态力学性能、力学性能、耐油、耐热氧老化及耐化学介质稳定性。发现PPC/NBR弹性体呈现IPN结构特征,加入PPC使NBR拉伸强度、扯断伸长率大幅度提高。PPC/NBR弹陸体具有优良的耐油及耐热氧老化稳定性。  相似文献   

17.
The thermal behaviour of nitrile rubber (NBR)/poly(ethylene-co-vinyl acetate) (EVA) blends was studied by thermogravimetry. The effects of blend ratio, different crosslinking systems (sulphur, peroxide and mixed), various fillers (silica, clay and carbon black) and filler loading on the thermal properties were evaluated. It was found that the initial decomposition temperature increased with the addition of NBR to EVA. Among the various crosslinking systems studied, the peroxide cured system showed the highest initial decomposition temperature. This is associated with the high bond dissociation energy of C–C linkages. The addition of fillers improved the thermal stability of the blend. The mass loss at different temperatures and activation energy of degradation were also studied. The thermal ageing of these blends was carried out at 50 and 100°C for 72 h. It was seen that the properties are not affected by the mild ageing condition. Also, the peroxide cured system was found to exhibit better retention in properties, than other crosslinking systems. This revised version was published online in August 2006 with corrections to the Cover Date.  相似文献   

18.
Bis(diisopropyl)thiophosphoryl disulfide (DIPDIS) has been used as a coupling cum curing agent for the compatibilization of blends of ethylene propylene diene monomer rubber (EPDM) with chloroprene rubber (CR). Electrical and mechanical properties of the blend vulcanizates have been studied to find the efficiency of the vulcanizing cum coupling activity of DIPDIS. The study reveals that CR in the presence of DIPDIS greatly improves the physical properties of EPDM. It is noted that the physical properties of the vulcanizates obtained from CR‐EPDM blend depend upon CR:EPDM ratio. The scanning electron microscopy (SEM) study reveals that it is possible to form a coherent blend of CR and EPDM in the presence of DIPDIS. Copyright © 2004 John Wiley & Sons, Ltd.  相似文献   

19.
The loading effect of precipitated silica (PSi) and fly ash‐based silica (FASi) on mechanical properties of natural rubber/chloroprene (NR/CR) under thermal and thermal‐oil ageing was investigated with variation in NR content in the NR/CR blends. The selected results were compared with vulcanized NR/nitrile rubber (NR/NBR) blends. The cure time of CR vulcanizate was found to decrease with increasing NR content, but increased with silica fillers. The Mooney viscosity for CR vulcanizates reduced with increasing NR content. The addition of NR had no effect on tensile modulus and tensile strength for the FASi filled NR/CR, but the opposite trend was observed for the PSi filled NR/CR. The post‐curing effect was more significant in PSi filled NR/CR than in FASi filled NR/CR. The tensile strength of the NR/CR vulcanizates was slightly reduced after thermal ageing especially at high NR content, more extreme reduction being found by thermal‐oil ageing. The elongation at break of NR/CR with both silica fillers ranged from 400 to 900%. The hardness results were similar to the tensile modulus. The addition of PSi in NR/CR considerably increased the tear strength, but less pronounced effect was found for FASi. The resilience properties of NR/CR tended to decrease with increasing silica content. The compression set became poorer when NR content was increased. The PSi showed higher improvement in compression set than the FASi. The effects of silica and ageing on the mechanical properties for NR/CR vulcanizates were similar to those for NR/NBR vulcanizates. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

20.
ABSTRACT

Rapidly increasing demands for higher integration density and stability of electronic devices embrace higher requirements for thermally conductive silicone rubber, which is promisingly used in ultra-thin components. In this work, alumina whiskers (AWs) and alumina flakes (AFs) are used to modify liquid silicone rubber (LSR) by fabricating binary (AFs/LSR) or ternary (AWs/AFs/LSR) composites. The thermal conductivity and mechanical strength of the binary and ternary composites were investigated. Thermal conductivity of the binary AFs/LSR composite (25AFs/LSR) was 0.1990 W m?1 K?1, while the thermal conductivity of the ternary AFs/AWs/LSR composite (20AFs/5AWs/LSR) was 0.2655 W m?1 K?1. Furthermore, the tensile strength of the ternary AWs/AFs/LSR composites increased by 180.9% as compared with the binary system, increased to 7.81 MPa from 2.78 MPa due to the introduction of 1 wt% AWs. As a reason, a significant synergistic effect of AWs and AFs in the enhancement of both thermal and mechanical properties of the LSR was proved. Furthermore, the dielectric property measurements demonstrated that the ternary composites exhibited a lower dielectric constant and dielectric loss, indicating that the AWs/AFs/LSR composites were qualified to be applied in the field of electronic devices.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号