Effects of thermal annealing on the viscoelastic properties and morphology of bimodal hard/soft latex blends

The effects of thermal annealing on the viscoelastic properties and morphology of films prepared from bimodal latex blends containing equal weight fractions of soft and hard latex particles with controlled sizes were investigated. The thermal and viscoelastic properties of as‐dried and annealed samples were investigated with differential scanning calorimetry and dynamic mechanical analysis (DMA). Throughout the thermal annealing, the latex blend morphologies were also followed with atomic force microscopy and transmission electron microscopy (TEM). A particulate morphology, consisting of hard particles evenly dispersed in a continuous soft phase, was observed in the TEM micrographs of the as‐dried latex blends and resulted in an enhancement of the mechanical film properties at temperatures between the α relaxations of the soft and hard phases in the DMA thermograms. As soon as the thermal annealing involved temperatures higher than the glass‐transition temperature of the hard phase, the hard particles progressively lost their initial spherical shape and formed a more or less continuous phase in the latex blends. This induced coalescence of the hard particles was confirmed by the association of the experimental viscoelastic data with theoretical predictions, based on self‐consistent mechanical models, which were performed by the consideration of either a particulate or cocontinuous morphology for the bimodal latex blends. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2289–2306, 2005     

Preparation and Characterization of Nanocomposite Films from Chitin Whisker and Waterborne Poly(ester-urethane) With or Without Ultra-Sonification Treatment

Two series of nanocomposite films were prepared from waterborne poly(ester-urethane) and chitin whisker with and without ultrasound treatment coded as CW/WPU and CHW/WPU, respectively. The effects of ultra-sonification method and chitin whisker content on the chemical compositions, crystallization behavior and miscibility were studied by attenuated total reflection Fourier transform infrared (ATR-FTIR), wide-angle X-ray diffraction (WXRD), dynamic mechanical analysis (DMA) and scanning electron microscopy (SEM). Thermal stability and mechanical properties of the films were measured by thermogravimetric analysis (TGA) and tensile test, respectively. The results revealed that both nanocomposite films exhibited a certain degree of miscibility when chitin whisker content was lower than 30 wt%, resulting in higher thermal stability and tensile strength than the pure waterborne poly(ester-urethane) film. Interestingly, the composite films CW/WPU with ultrasound treatment possessed better miscibility, storage modulus, thermal stability and tensile strength than those without ultrasound treatment over the entire composition range studied here. The difference can be attributed to the relatively higher dispersion level of whisker within poly(ester-urethane) matrix resulting in relatively stronger entanglement and interaction between both components. The ultrasound treatment can effectively improve the miscibility and mechanical properties of the casting nanocomposite films with nano-meter size chitin whisker added. This indicated that the structure, miscibility and mechanical properties of the nanocomposite films depended significantly on the preparation method.     

Preparation and Characterization of Blend Films of Poly(Vinyl Alcohol) and Sodium Alginate

Blend films of poly(vinyl alcohol) (PVA) and sodium alginate (NaAlg) were prepared by casting from aqueous solutions. This blend films were characterized by tensile strength test, Fourier transform infrared spectroscopy (FT‐IR), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The miscibility in the blends of PVA and NaAlg was established on the basis of the thermal analysis results. DSC showed that the blends possessed single, composition‐dependent glass transition temperatures (T_gs), indicating that the blends are miscible. FT‐IR studies indicate that there is the intermolecular hydrogen bonding interactions, i.e. –OH…^?OOC– in PVA/NaAlg blends. The blend films also exhibited the higher thermal stability and their mechanical properties improved compared to those of homopolymers.     

Effects of different types of polyethylene on the morphology and properties of recycled poly(ethylene terephthalate)/polyethylene compatibilized blends

Recycled poly(ethylene terephthalate) (R‐PET) was blended with four types of polyethylene (PE), linear low density polyethylene (LLDPE; LL0209AA, Fs150), low density polyethylene (LDPE; F101‐1), and metallocene‐LLDPE (m‐LLDPE; Fv203) by co‐rotating twin‐screw extruder. Maleic anhydride‐grafted poly(styrene‐ethylene/butyldiene‐styrene) (SEBS‐g‐MA) was added as compatibilizer. R‐PET/PE/SEBS‐g‐MA blends were examined by scanning electron microscopy (SEM), differential scanning calorimeter (DSC), dynamic mechanical analysis (DMA), and mechanical property testing. The results indicated that the morphology and properties of the blends depended to a great extent on the miscibility between the olefin segments of SEBS‐g‐MA and PE. Due to the proper interaction between SEBS‐g‐MA and LDPE (F101‐1), most SEBS‐g‐MA, located at the interface between two phases of PET and LDPE to increase the interfacial adhesion, lead to better mechanical properties of R‐PET/LDPE (F101‐1) blend. However, both the poor miscibility of SEBS‐g‐MA with LLDPE (LL0209AA) and the excessive miscibility of SEBS‐g‐MA with LLDPE (Fs150) and m‐LLDPE (Fv203) reduced the compatibilization effect of SEBS‐g‐MA. DSC results showed that the interaction between SEBS‐g‐MA and PE obviously affected the crystallization of PET and PE. DMA results indicated that PE had more influence on the movement of SEBS‐g‐MA than PE did. Copyright © 2010 John Wiley & Sons, Ltd.     

Miscibility Study of Blends of Polysulfone with a Methacrylamide Polymer Containing Quaternized Alkylammonium Sites

Abstract

Polymer films of polysulfone (PSF) and the copolymer poly(N,N‐[(dimethylamino)propyl] methacrylamide‐co‐methacrylamido propyl‐N,N‐dimethyl‐N‐dodecylammonium bromide), QPMADAP, containing a large fraction of dodecylammonium (36?mol%) groups, were prepared by film casting. The differential scanning calorimetry (DSC) investigation has shown that the miscibility behavior depends substantially on the solvent used. The introduction of QPMADAP in the PSF films does not lower the mechanical performance of the film, even if they contain up to 25% (w/w) QPMADAP, as evidenced by dynamic mechanical analysis (DMA) measurements. Moreover, the DSC and DMA investigation revealed a rather constant T _g depression of about 30°C, by the very first introduction of QPMADAP into the PSF matrix. FT‐Raman investigation of the surface of the solvent etched films verified that QPMADAP is not extracted by methanol. Furthermore, the morphological investigation by scanning electron micrography (SEM) revealed the formation of QPMADAP nanophases with dimensions less than 100?nm onto a PSF matrix.     

Effect of molecular interactions on the miscibility and structure of polymer blends

The effect of polymer-polymer interactions on the miscibility and macroscopic properties of PVC/PMMA, PVC/PS and PMMA/PS blends were studied in the entire composition range. The miscibility of the components was characterized by the Flory-Huggins interaction parameter or by quantities related to it. Thermal analysis, light transmittance measurements, and scanning electron microscopy were carried out on the blends and their mechanical properties were characterized by tensile tests. Interactions were analyzed by infrared spectroscopy and contact angle measurements. All three polymer pairs form heterogeneous blends, but the strength of molecular interactions is different in them, the highest is in PVC/PMMA system resulting in partial miscibility of the components and beneficial mechanical properties. The structure of these blends depends strongly on composition. A phase inversion can be observed between 0.5 and 0.6 PMMA content accompanied with a significant change in structure and properties. The PVC/PS and the PMMA/PS pairs are immiscible, though the results indicate the partial solubility of the components. The analysis of the surface characteristics of the components and the comparison of quantities derived from them with miscibility as well as with the macroscopic properties of blends revealed that blend properties cannot be predicted in this way, since they are affected by several factors.     

PA66/PA12/clay based nanocomposites: structure and thermal properties

In a previous paper the structure and the physical properties of melt mixed polyamide 66 (PA66)/polyamide 12 (PA12) blends characterized by different compositions have been investigated by means of morphological and physical analyses. A low amount of organically‐modified layered silicate (OMLS, 4 wt%) was introduced in order to evaluate its effect on blends structure and components miscibility. This paper completes the characterization of these materials investigating their thermal properties by means of standard and modulated differential scanning calorimetry (DSC, MDSC), dynamic‐mechanical analysis (DMA), and thermogravimetric analysis (TGA). The partial miscibility of PA66 and PA12, with phase separation depending on blend composition, has been confirmed by analyzing the glass transition temperature (T_g) dependence on composition as well as the existence of strong segmental interactions between polymer components. A compatibilizing action of OMLS has been observed because of a lowering of interfacial tension avoiding coalescence phenomena between particles during melt mixing process. Copyright © 2010 John Wiley & Sons, Ltd.     

Processing and characterization of LDPE/starch/PCL blends

Low-density polyethylene/plasticized starch/polycaprolactone blends were processed by conventional extrusion, injection molding, and film blowing techniques. The glass transition temperatures of plasticized starch were determined using differential scanning calorimetry. The blends were characterized by mechanical property measurements and scanning electron microscopy. The blend properties were found to depend not only on composition but also on the generated morphology. In films the fine dispersion of polycaprolactone phase in the polyethylene/starch matrix resulted in mechanical property increase, while in injection specimens there was property decrease due to phase coalescence. It appears that the different conditions existing at the two different shaping processes i.e. film blowing and injection molding could account for the final obtained morphology.     

Miscibility studies of PVC/Aramid blends

Blends containing PVC and aramid (Ar) matrices were probed for their miscibility. In this respect, Ar chains were synthesized by aromatic diamine and diacid chloride in amide solvent. The Ar thus synthesized was characterized through Fourier transform infrared (FTIR) spectroscopy and molecular weight determination. Blend system Ar/PVC was investigated over a range of Ar/PVC ratios. Their mechanical profiles in terms of maximum stress, maximum strain, toughness, and initial moduli have been explored. Thermal properties and morphology of the blends were estimated using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and scanning electron microscopy (SEM). A good correlation was observed between thermal, mechanical, and morphological properties of the blends. The presence of hydrogen bonding among polymers was evaluated through FTIR spectroscopy, which is believed to be responsible for the blend miscibility. Optimal thermal and mechanical profiles were depicted by the blend containing 40-wt% PVC in the Ar matrix.     

Development of the morphology and crystalline state due to hybridization of reinforced toughened nylon containing a liquid‐crystalline polymer

A hybrid composite consisting of rubber‐toughened nylon‐6,6, short glass fibers, and a thermotropic liquid‐crystalline polymers (LCP) was investigated by the LCP content being varied. The thermal behavior, morphology, and crystallization behavior due to hybridization were studied by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and wide‐angle X‐ray scattering (WAXS). DSC results indicated that the crystallinity of the glass‐fiber‐reinforced toughened nylon‐6,6 was reduced by LCP addition, particularly 5–10 wt % LCP. DMA data showed that the miscibility between the blended components was maximum at the 5 wt % LCP composition, and the miscibility decreased with increasing LCP content. SEM photomicrographs revealed information consistent with the thermal behavior on miscibility. It was also observed that the 10 wt % LCP composition showed predominantly an amorphous character with FTIR and WAXS. WAXS results indicated that LCP hybridization increased the interplanar spacing of the hydrogen‐bonded sheets of the nylon crystals rather than the spacing between the hydrogen‐bonded chains. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 549–559, 2003     

PA66/PA12/clay based nanocomposites: morphology and physical properties

The structure and the physical properties of several polyamide 66 (PA66)/polyamide 12 (PA12) blends containing different amounts of the two polymers and obtained by melt‐blending have been investigated. A low amount of organically‐modified layered silicate (OMLS, 4 wt%) has also been introduced in order to further improve the physical properties and, in particular, to evaluate its effect on the blends' structure and components' miscibility. The microstructure and morphology of all the composites were analyzed by means of X‐Ray diffraction (WAXD), transmission electron microscopy (TEM), and high resolution scanning electron microscopy (SEM), while the macroscopic scale properties (mechanical behavior and water adsorption) were assessed in order to investigate and understand the materials' structure–properties relationships. The partial miscibility of PA66 and PA12, with phase separation depending on blend composition, has been confirmed. The results also underlined the possibility to tailor the behavior of polymer blends in terms of mechanical water adsorption properties by varying the amount of PA12, added to PA66 with and without the addition of the OLMS. The effectiveness of the clay in modifying the components' miscibility as well as its tendency to segregate preferentially within separate PA66 domains have been assessed. WAXD results showed opposite effects of PA12 and clay on the crystallization behavior of PA66, an aspect that has also been deepened in another paper by the same authors discussing the results of the complete thermal characterization. Copyright © 2010 John Wiley & Sons, Ltd.     

Synthesis and characterization of a vinyl‐terminated benzoxazine monomer and its blends with poly(ethylene oxide)

A vinyl‐terminated benzoxazine (VB‐a), which could be polymerized through ring‐opening polymerization, was synthesized through the Mannich condensation of bisphenol A, formaldehyde, and allylamine. This VB‐a monomer was then subjected to blending with poly(ethylene oxide) (PEO), followed by thermal curing, to form poly(VB‐a)/PEO blends. The specific interactions, miscibility, morphology, and thermal properties of these blends were investigated with Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry, dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). Before curing, we found that PEO was miscible with VB‐a, as evidenced by the existence of a single composition‐dependent glass transition temperature (T_g) for each composition. The FTIR spectra revealed the presence of hydrogen‐bonding interactions between the hydroxyl groups of poly(VB‐a) and the ether groups of PEO. Indeed, the ring‐opening reaction and subsequent polymerization of the benzoxazine were facilitated significantly by the presence of PEO. After curing, DMA results indicated that the 50/50 poly(VB‐a)/PEO blend exhibited two values of T_g: one broad peak appeared in the lower temperature region, whereas the other (at ca. 327 °C, in the higher temperature region) was higher than that of pristine poly(VB‐a) (301 °C). The presence of two glass transitions in the blend suggested that this blend system was only partially miscible. Moreover, SEM micrographs indicated that the poly(VB‐a)/PEO blends were heterogeneous. The volume fraction of PEO in the blends had a strong effect on the morphology. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 644–653, 2007     

Star‐like polyurethane hybrids with functional cubic silsesquioxanes: Preparation,morphology, and thermomechanical properties

Star‐like polyurethane (PU) hybrid films containing octafunctional cubic silsesquioxanes are prepared by polyaddition reaction between octakis(dimethylsilyloxy) silsesquioxane isopropenyldimethylbenzyl isocyanate (OS‐PDBI) and octakis(dimethylsilyloxy) hydroxypropyl silsesquioxane (HPS); and between OS‐PDBI and hexane diol (HD). The effect of incorporation of nanostructured cubic silsesquioxanes (CSSQ) on the macroscopic properties of PU film and their thermomechanical properties are investigated. The obtained hybrid films are relatively transparent. Their morphologies and properties are studied by using Fourier transform infra‐red spectroscopy (FTIR), X‐ray diffraction (XRD), atomic force microscopy (AFM), thermogravimetry (TGA), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and contact angle measurements. The formation of urethane linkage disrupts the three‐dimensional ordered structure of CSSQ in the hybrid film. AFM images show clearly that no phase separation in the macroscopic level for both PU hybrid films. TGA and DMA analyzes indicate that the incorporation of octafunctional silsesquioxane in PU hybrid film provides enhanced thermal stability and increased crosslink density. Moreover, the existence of cage structure also improves oxidation resistance and mechanical strength. The incomplete reaction between OS‐PDBI and HPS due to the steric hindrance of highly branched rigid CSSQ could result in a slight decrease in initial decomposition temperature. Furthermore, hardness and out‐of‐plane compressive modulus are also investigated by nanoindentation. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4602–4616, 2009     

线性低密度聚乙烯／乙烯醋酸乙烯共聚物共混体系的相容性及性能

线性低密度聚乙烯／乙烯醋酸乙烯共聚物共混体系的相容性及性能杨毓华＊白春霞花荣于李三喜（中国科学院长春应用化学研究所长春１３００２２）（沈阳化工学院高分子科学与工程系沈阳）关键词线性低密度聚乙烯，乙烯醋酸乙烯共聚物，共混，相容性，ＤＳＣ，ＷＡＸＤ，力...     

Polyamide 11/poly(hydroxy amino ether) blends: Influence of the blend composition and morphology on the barrier and mechanical properties

A series of PA11/PHAE blends was prepared by melt mixing across the full composition range. Films were obtained for each composition by an extrusion-cast process keeping the same processing conditions. The blends exhibited a two phase morphology. PHAE-rich nodules surrounded by the PA11-rich matrix were observed for PA11 contents higher than 50 wt% in the blends. For lower PA11 weight amounts, PA11 became the dispersed phase and appeared as long fibrillar domains lying in the plane of the film. PA11/PHAE interactions were discussed from DSC and DMA analyses. The effects of the blend composition and morphology on mechanical properties in the linear range and on hydrogen barrier properties were investigated. Hydrogen permeability decreased with increasing amount of PHAE in the blends. A confrontation between the experimental permeability values and the theoretical ones calculated by taking account of the specific properties and morphology of the PA11- and PHAE-rich phases was carried out. In the films series under study, the improvement of hydrogen barrier properties was mainly related to the blend composition whereas a significant effect of the blend morphology was observed on mechanical properties in the rubbery state.     

Morphology and conduction properties of graphite‐filled immiscible PVDF/PPgMA blends

Graphite was dispersed in immiscible polyvinylidene fluoride/maleated polypropylene (PVDF/PPgMA) blends to improve electrical and thermal conductive properties by building a double‐percolation structure. The morphology of PVDF/PPgMA blends was first investigated for several compositions by selective solvent extraction, scanning electron microscopy, and dynamic mechanical thermal analysis. Blends of PVDF and PPgMA were prepared in different relative fractions, and a PVDF/PPgMA ratio of 7/3 showed a well‐co‐continuous structure. From this blend, the morphology and properties of composites with different concentrations of graphite were investigated to prepare double‐percolated structures. Graphite was observed to selectively localize in the PPgMA phase. The electrical and thermal conductive properties of graphite‐containing blends were measured, showing enhanced conductivity for the double‐percolation structures compared with single‐polymer composites containing the same graphite loadings. Copyright © 2012 John Wiley & Sons, Ltd.     

Modification of mechanical and thermal property of chitosan–starch blend films

Chitosan–starch blend films (thickness 0.2 mm) of different composition were prepared by casting and their mechanical properties were studied. To improve the properties of chitosan–starch films, glycerol and mustard oil of different composition were used. Chitosan–starch films, incorporated with glycerol and mustard oil, were further modified with monomer 2-hydroxyethyl methacrylate (HEMA) using gamma radiation. The modified films showed improvement in both tensile strength and elongation at break than the pure chitosan–starch films. Water uptake of the films reduced significantly than the pure chitosan–starch film. Thermo gravimetric analysis (TGA) and dynamic mechanical analysis (DMA) showed that the modified films experience less thermal degradation than the pure films. Scanning electron microscopy (SEM) and FTIR were used to investigate the morphology and molecular interaction of the blend film, respectively.     

Structure,properties and interfacial interactions in poly(lactic acid)/polyurethane blends prepared by reactive processing

Polyurethane elastomers are promising candidates for the impact modification of PLA producing blends for example for biomedicine. Poly(lactic acid) (PLA)/polyurethane elastomer (PU) blends were prepared by reactive processing and physical blending as comparison. The blends were characterized by a number of techniques including microscopy (scanning electron microscopy, SEM, and atomic force microscopy, AFM), rotational viscometry, thermal (dynamic mechanical analysis, DMA), and mechanical (tensile) measurements. The analysis and comparison of the structure and properties of physical and reactor blends proved the successful coupling of the phases. Coupling resulted in more advantageous structure and superior mechanical properties compared to those of physical blends as confirmed by morphology, macroscopic properties and the quantitative estimation of interfacial interactions. Structural studies and the composition dependence of properties indicated the formation of a submicron, phase-in-phase structure which positively influenced properties at large PU contents. The results strongly support that reactive processing is a convenient, cost-effective and environmentally friendly technique to obtain blends with superior properties.     

Miscibility‐property correlations in blends of glassy amorphous polymers

Blends were prepared from seven polymers in various combinations in the entire composition range. The Flory‐Huggins interaction parameter (χ₁₂) was used for the quantitative estimation of miscibility. The determination of χ₁₂ was attempted by several experimental techniques including the measurement of transparency, glass transition temperature, solvent diffusion and mechanical properties. The relatively simple methods used for the estimation of miscibility work surprisingly well. Solvent absorption can be determined easily for practically all blends, thus the method offers a quantitative measure of component interaction if the solvent is selected properly. After appropriate data reduction, the composition dependence of mechanical properties also supplies a quantitative estimate of compatibility. Although the approach presented in the paper reflects well the general correlation between miscibility and properties, it must be refined and improved in order to obtain a reliable estimate of blend performance.     

Miscibility and compatibilization of poly(trimethylene terephthalate)/acrylonitrile-butadiene-styrene blends

Poly(trimethylene terephthalate)/acrylonitrile-butadiene-styrene (PTT/ABS) blends were prepared by melt processing with and without epoxy or styrene-butadiene-maleic anhydride copolymer (SBM) as a reactive compatibilizer. The miscibility and compatibilization of the PTT/ABS blends were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), capillary rheometer and scanning electron microscopy (SEM). The existence of two separate composition-dependent glass transition temperatures (T_gs) indicates that PTT is partially miscible with ABS over the entire composition range. In the presence of the compatibilizer, both the cold crystallization and glass transition temperatures of the PTT phase shifted to higher temperatures, indicating their compatibilization effects on the blends.The PTT/ABS blends exhibited typical pseudoplastic flow behavior. The rheological behavior of the epoxy compatibilized PTT/ABS blends showed an epoxy content-dependence. In contrast, when the SBM content was increased from 1 wt% to 5 wt%, the shear viscosities of the PTT/ABS blends increased and exhibited much clearer shear thinning behavior at higher shear rates. The SEM micrographs of the epoxy or SBM compatibilized PTT/ABS blends showed a finer morphology and better adhesion between the phases.