Structural,thermal and ion transport studies on nanocomposite polymer electrolyte-{(PEO + SiO<Subscript>2</Subscript>):NH<Subscript>4</Subscript>SCN} system

Development and characterisation of polyethylene oxide (PEO)-based nanocomposite polymer electrolytes comprising of (PEO-SiO₂): NH₄SCN is reported. For synthesis of the said electrolyte, polyethylene oxide has been taken as polymer host and NH₄SCN as an ionic charge supplier. Sol–gel-derived silica powder of nano dimension has been used as ceramic filler for development of nanocomposite electrolytes. The maximum conductivity of electrolyte ∼2.0 × 10⁻⁶ S/cm is observed for samples containing 30 wt.% silica. The temperature dependence of conductivity seems to follow an Arrhenius-type, thermally activated process over a limited temperature range.     

Role of composite MnO2 cathode on electrochemical cells based on polymer electrolyte (PEO/NaClO3)

Thin-film sodium-ion-conducting polymer electrolyte based on polyethylene oxide (PEO) system was prepared by solvent casting method. The thin-film electrolytes were characterized by X-ray diffraction (XRD), infrared (IR), cyclic voltammetry (CV) and alternating current conductivity, and Wagner’s polarization method. The complexation of salt with PEO was confirmed by XRD and IR studies. The charge transport of these electrolytes is mainly due to ions, which was confirmed by the transference number experiment. The conductivity studies show that the conductivity value of PEO/NaClO₃ complex increases with the increase of temperature as well as the addition of low molecular weight polyethylene glycol, dimethyl formamide, and propylene carbonate. The electrolyte stability and cell reversibility were analyzed by CV studies. Electrochemical cells have been fabricated with a common cell configuration Na|electrolyte|(MnO₂ + I₂ + C + electrolyte), and their discharge characteristic studies were made through a load 100 kΩ at room temperature. The measured open circuit voltage ranges from 2.80 to 2.54 V with short circuit current ranges from 667 to 1,000 μA and several other cell parameters were evaluated. Finally, the merit of the composite cathode is found with the comparison of the MnO₂ cathode.     

A novel PEO-based composite polymer electrolyte with NaAlOSiO molecular sieves powders

Ion-conducting thin film polymer electrolytes based on poly(ethylene oxide) (PEO) complexes with NaAlOSiO molecular sieves powders has been prepared by solution casting technique. X-ray diffraction, scanning electron microscopy, differential scanning calorimeter, and alternating current impedance techniques are employed to investigate the effect of NaAlOSiO molecular sieves on the crystallization mechanism of PEO in composite polymer electrolyte. The experimental results show that NaAlOSiO powders have great influence on the growth stage of PEO spherulites. PEO crystallization decrease and the amorphous region that the lithium-ion transport is expanded by adding appropriate NaAlOSiO, which leads to drastic enhancement in the ionic conductivity of the (PEO)₁₆LiClO₄ electrolyte. The ionic conductivity of (PEO)₁₆LiClO₄-12 wt.% NaAlOSiO achieves (2.370 ± 0.082) × 10⁻⁴ S · cm⁻¹ at room temperature (18 °C). Without NaAlOSiO, the ionic conductivity has only (8.382 ± 0.927) × 10⁻⁶ S · cm⁻¹, enhancing 2 orders of magnitude. Compared with inorganic oxide as filler, the addition of NaAlOSiO molecular sieves powders can disperse homogeneously in the electrolyte matrix without forming any crystal phase and the growth stage of PEO spherulites can be hindered more effectively.     

The role of electrolyte in governing the performance of protonic solid state battery

The solid-state proton conductor, P₂O₅.5H₂O, is found very difficult to handle due to presence of a very high content of moisture and corrosive nature. The addition of Al₂O₃ and SiO₂ into P₂O₅.5H₂O, forming composite electrolytes, obviates said drawback. The Zn + ZnSO₄ used as an anode to prepare cells with different cathode viz. I₂, MnO₂, PbO₂, and V₆O₁₃ characterized under different conditions. Open circuit voltage, discharge current and discharge time, on load voltage, discharge capacity, power density, and energy density are evaluated from discharge properties. Protonically conducting composite 70(P₂O₅.5H₂O)/30[(92SiO₂)/08(Al₂O₃)] is found to be the optimum combination with the optimized 50Zn/50ZnSO₄ as anode and 40MnO₂/60 graphite as cathode from secondary battery view point. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006     

Conductivity studies of starch-based polymer electrolytes

A proton-conducting polymer electrolyte based on starch and ammonium nitrate (NH₄NO₃) has been prepared through solution casting method. Ionic conductivity for the system was conducted over a wide range of frequency between 50 Hz and 1 MHz and at temperatures between 303 K and 373 K. Impedance analysis shows that sample with 25 wt.% NH₄NO₃ has a smaller bulk resistance (R _b) compared to that of the pure sample. The amount of NH₄NO₃ was found to influence the proton conduction; the highest obtainable room temperature conductivity was 2.83 × 10⁻⁵ S cm⁻¹, while at 100 °C, the conductivity in found to be 2.09 × 10⁻⁴ S cm⁻¹. The dielectric analysis demonstrates a non-Debye behavior. Transport parameters of the samples were calculated using the Rice and Roth model and thus shows that the increase in conductivity is due to the increase in the number of mobile ions.     

In situ production of CuS particles in polymer electrolyte matrix for mixed ion+electron conduction

Composites of polymer electrolyte polyethylene oxide (PEO) complexed with NH₄ClO_4, (PEO:NH₄ClO₄), having different weight ratios of dispersed semiconductor CuS (0–5 wt.%) have been prepared and characterized. The dispersal of CuS was achieved by its in situ formation in the viscous solution of polymer electrolyte (PEO:NH₄ClO₄) by sulfuration of CuSO₄ using H₂S. The band gap of CuS dispersed in the composites was found to be ~2.4 eV, which is higher than that of the bulk CuS for which it is 2.2 eV. Scanning electron microscopy studies show that the particle size varies from ~200 nm to several hundreds of nanometers. Polarization studies show that the semiconductor dispersed polymer composite so obtained has mixed ionic and electronic conduction. Detailed I–V studies show that the dispersoid is a p-type semiconductor.     

Nano-composite solid polymer electrolytes for solid state ionic devices

Recent research efforts to improve the ambient temperature conductivity in polyethylene oxide (PEO) based solid polymer electrolytes have been directed towards the incorporation of ultra-fine nano-sized particles of ceramic fillers such as Al₂O₃, γ-LiAlO₂, SiO₂ and TiO₂ into the polymer electrolyte. In these PEO based nano-composite polymer electrolytes, conductivity enhancements of up to two orders of magnitude have been achieved. Thermal, electrical conductivity and dielectric relaxation measurements performed on several nano-composite polymer electrolyte systems have shown that the degree of enhancement depends primarily on the grain size. In this paper, results of three nano-composite polymer electrolyte systems, PEO:LiTFSI:Al₂O₃, PEO:LiTf:Al₂O₃ and PEO:LiTf: SiO₂ are discussed as representative examples. It is suggested that the conductivity enhancement is due to the creation of additional sites and favourable conduction pathways for ionic transport through Lewis acidbase type interactions between the filler surface groups (H/OH) and the ionic species. Paper presented at the 2nd International Conference on Ionic Devices, Anna University, Channai, India, Nov. 28–30, 2003.     

Characterization of high ionic conducting PVAc–PMMA blend-based polymer electrolyte for electrochemical applications

A solid polymer blend electrolyte is prepared using poly(vinyl acetate) (PVAc) and poly(methyl methacrylate) (PMMA) polymers with different molecular weight percentage (wt%) of ammonium thiocyanate (NH₄SCN) by solution casting technique with tetrahydrofuran (THF) as a solvent. The structural, morphological, vibrational, thermal and electrical properties of the prepared polymer blend electrolytes have been studied. The incorporation of NH₄SCN into the polymeric matrix causes decrease in the degree of crystallinity of the samples. The complex formation between the polymer and salt has been confirmed by FTIR technique. The increase in T _g with increase in salt concentration has been investigated. The maximum conductivity of 3.684?×?10^?3 S cm^?1 has been observed for the composition of 70PVAc/30PMMA/30 wt% of NH₄SCN at 303 K. This value of ionic conductivity is five orders of magnitude greater than that of 70PVAc/30PMMA polymer membrane. Dielectric and transport studies have been done. The highest conducting polymer electrolyte is used to fabricate proton battery with the configuration Zn/ZnSO₄·7H₂O (anode) ||polymer electrolyte||PbO₂/V₂O₅ (cathode). The open circuit voltage of the fabricated battery is 1.83 V, and its performance has been studied.     

Structural and ionic conductivity studies on proton conducting polymer electrolyte based on polyvinyl alcohol

An attempt has been made to prepare a new proton conducting polymer electrolyte based on polyvinyl alcohol (PVA) doped with NH₄NO₃ by solution casting technique. The complex formation between polymer and dissociated salt has been confirmed by X-ray diffraction analysis. The ionic conductivity of the prepared polymer electrolyte has been found by ac impedance spectroscopic analysis. The highest ionic conductivity has been found to be 7.5 × 10⁻³ Scm⁻¹ at ambient temperature for 20 mol% NH₄NO₃-doped PVA with low activation energy (~0.19 eV). The temperature-dependent conductivity of the polymer electrolyte follows an Arrhenius relationship, which shows hopping of ions in the polymer matrix.     

Cells studies on PEO/PEG/NaClO<Subscript>3</Subscript> thin-film electrolyte system based on composite V<Subscript>2</Subscript>O<Subscript>5</Subscript> electrode

The thin-film solid polymer electrolyte based on polyethylene oxide (PEO) with sodium chlorite (NaClO₃) has been prepared by a solution-cast technique. The electrolyte was characterized by X-ray diffraction (XRD), infrared (IR), cyclic voltammetry, alternating current conductivity, and Wagner’s polarization studies. The complexation of NaClO₃ with PEO was confirmed through the XRD and IR studies. The transference number measurement has shown that the ion transport is predominant over electrons in the polymer electrolytes (t _ions ≈ 0.94). The conductivity enhancement was observed in the case of the PEO/NaClO₃ system with the addition of plasticizers (low-molecular-weight polyethylene glycol, organic solvents propylene carbonate and dimethyl formamide. Cyclic voltammetry analysis showed the stability and redox character of the electrolyte and electrode. Finally, polymer electrolyte systems were examined by electrochemical cell studies using V₂O₅ and composite V₂O₅ cathode at temperature of 35 °C. Overall, the plasticized electrolyte shows a better electrochemical performance, and a higher discharge capacity was observed in composite V₂O₅-based cells over V₂O₅-based cells.     

Electrical characterization of nano-composite polymer gel electrolytes containing NH4BF4 and SiO2: role of donor number of solvent and fumed silica

Nano-composite polymer gel electrolytes were synthesized by using polyethylene oxide (PEO), ammonium tetrafluoroborate (NH₄BF₄), fumed silica (SiO₂), dimethylacetamide (DMA), ethylene carbonate (EC), and propylene carbonate (PC) and characterized by conductivity studies. The effect of donor number of solvent on ionic conductivity of polymer gel electrolytes has been studied. The mechanical strength of the gel electrolytes has been increased with the addition of nano-sized fumed silica along with an enhancement in conductivity. Maximum room temperature ionic conductivity of 2.63 × 10⁻³ and 2.92 × 10⁻³ S/cm has been observed for nano-composite gel electrolytes containing 0.1 and 0.5 wt% SiO₂ in DMA+1 M NH₄BF₄+10 wt% PEO, respectively. Nano-composite polymer gel electrolytes having DMA have been found to be thermally and electrically stable over 0 to 90 °C temperature range. Also, the change in conductivity with the passage of time is very small, which may be desirable to make applicable for various smart devices.

     

Ionic conductivity and battery characteristic studies on PEO+NaClO3 polymer electrolyte

Solid polymer electrolyte films based on poly (ethylene oxide) PEO complexed with NaClO₃ have been prepared by a solution-cast technique. The solvation of Na⁺ ion with PEO is confirmed by XRD and IR studies. Measurements of the a.c. conductivity in the temperature range 308 – 378 K and the transference numbers have been carried out to investigate the charge transport in this polymer electrolyte system. Transport number data show that the charge transport in this polymer electrolyte system is predominantly due to ions. The highest conductivity (2.12.10⁻⁴ S/cm) has been observed for the 70:30 composition. Using the polymer electrolyte solid state electrochemical cells have been fabricated. The various cell parameters are evaluated and reported.     

Cobalt-containing oxide layers on titanium, their composition, morphology, and catalytic activity in CO oxidation

In this study possibility to form the layered compositions CoO_x + SiO₂/TiO₂/Ti by plasma electrolytic oxidation (PEO) method was shown. Compositions have been obtained by both one-stage PEO method (Method I) with addition of Co(CH₃COO)₂ into silicate electrolyte and impregnation of preliminary obtained by the PEO method SiO₂/TiO₂/Ti systems in aqueous solutions containing cobalt salts with their following annealing (Method II). XRD, XPS and SEM/EDX were used to investigate the phase and element composition, microstructure of the coatings prepared by the two various methods. Catalytic activity of the cobalt-containing composites was investigated in the CO oxidation reaction. Under experimental conditions, the structures obtained by impregnation and annealing method were more active, than those obtained by one-stage PEO method. The surface structures of cobalt-containing coatings obtained by the PEO method and by impregnation and annealing differ in both quantitative and qualitative relation. The cobalt content on the surface of impregnating coatings is three times as much as that for those formed by one-stage PEO method. It is found that coatings obtained by the Method II have a more developed surface. The surface of CoO_x + SiO₂/TiO₂/Ti compositions obtained by the PEO method contains, presumably Co(OH)₂ and Co₃O₄. The surface of the similar compositions obtained by the Method II, possibly contains CoO, either Co₂O₃, or CoOOH. The combination of these factors, perhaps, also provides a higher activity of the compositions formed by the Method II.     

Luminescence of Eu<Superscript>2+</Superscript> ions in alkaline earth dilithiosilicates

Spectral-luminescent properties of Eu²⁺ ions in alkaline earth dilithiosilicates of composition MLi₂SiO₄ (M = Ca, Sr, Ba) have been studied at 77 K. The reasons for the different positions of the Eu²⁺ 4f ⁶5 d → 4f ⁷ emission band maximum in spectra of MLi₂SiO₄ were found based on the obtained results. It was shown that the increase in the decay time of the Eu²⁺ emission on going from CaLi₂SiO₄ (0.41μs) through BaLi₂SiO₄ (0.64 μs) to Sr-silicate (1.11μs) correlates with the shift of the emission maximum to longer wavelengths.     

Photovoltaic activity in a ZnSe/PEO–chitosan blend electrolyte junction

Thin films of ZnSe and PEO–chitosan blend polymer doped with NH₄I and iodine crystals were prepared to form the two sides of a semiconductor electrolyte junction. ZnSe was electrodeposited on indium tin oxide (ITO) conducting glass. The polymer is a blend of 50 wt% chitosan and 50 wt% polyethylene oxide. The polymer blend was complexed with ammonium iodide (NH₄I), and some iodine crystals were added to the polymer–NH₄I solution to provide the I⁻/I³⁻redox couple. The room temperature ionic conductivity of the polymer electrolyte is 4.32 × 10⁻⁶ S/cm. The polymer film was sandwiched between the ZnSe semiconductor and an ITO glass to form a ZnSe/polymer electrolyte/ITO photovoltaic cell. The open circuit voltage (V _oc) of the fabricated cells ranges between 200 to 400 mV and the short circuit current between 7 to 10 μA.     

Electrical conductivity response and sensitivity of ZSM-5, Y,and mordenite zeolites towards ethanol vapor

This work is an attempt to search for highly selective sensing materials for ethanol vapor. The electrical conductivity response of ZSM-5, Y, and mordenite zeolites towards ethanol vapor have been investigated for the effects of the framework, the charge balancing cation type, and the Si/Al ratio. All zeolites were characterized using XRD, FT-IR, SEM, TGA, BET, and NH₃-TPD techniques. For the effect of the zeolite framework type, H⁺Y has a higher electrical conductivity sensitivity value than that of H⁺MOR because of a greater pore volume and available surface area. For the effect of the charge balancing cation, all NH₄ ⁺ZSM-5 zeolites (Si/Al = 23, 50, 80, 280) show negative responses, whereas the H⁺Y zeolites (Si/Al = 30, 60, 80) and the H⁺MOR zeolites (Si/Al = 30, 200) show positive responses. These differing behaviors can be traced to the electrostatic field at the cation sites in zeolite micropores, and their hydrophilic–hydrophobic character, which affect the adsorption properties of the zeolites. For the effect of Si/Al ratio, the electrical conductivity sensitivity towards the ethanol decreases with increasing Si/Al ratio or decreasing Al content, and there is a lesser degree of interaction between ethanol molecules and the active sites of the zeolites due to its higher hydrophobicity and the lower amount of cations. However, the H⁺Y (Si/Al = 5.1) and the H⁺MOR (Si/Al = 19) zeolites have lower conductivity sensitivity than those of H⁺Y (Si/Al = 30) and H⁺MOR (Si/Al = 30), respectively. The interactions between the C₂H₅OH molecules and the zeolites with respect to the electrical conductivity sensitivity were investigated and verified through infrared spectroscopy.     

Solid polymer electrolytes based on squaric acid structure

Poly(squarate)s (PPS-1 and PPS-2) were synthesized by the reaction of squaryl dichloride with hydroquinone for PPS-1 and with 2,5-diethoxy-1,4-bis(trimethylsilyloxy)benzene for PPS-2, and the ionic conductivities, thermal properties, and electrochemical and thermal properties of their polymer electrolytes with LiN(CF₃SO₂)₂ were investigated. The ionic conductivity increased with increasing the lithium salt concentration for the PPS-1–LiN(CF₃SO₂)₂ electrolyte, and the highest ionic conductivities of 8.60 × 10⁻⁵ S/cm at 100 °C and 9.57 × 10⁻⁸ S/cm at 30 °C were found at the [Li] to [O] ratio of 2:1. And also, the ionic conductivity for the PPS-1–LiN(CF₃SO₂)₂ electrolyte increased with an increase in the lithium salt concentration, reached a maximum value at the [Li] to [O] ratio of 1:2, and then decreased. The highest ionic conductivity was to be 1.04 × 10⁻⁵ S/cm at 100 °C and 1.71 × 10⁻⁸ S/cm at 30 °C, respectively. Both polymer electrolytes exhibited relatively better electrochemical and thermal stabilities. Addition of the PPS-1 as a plasticizer into the poly(ethylene oxide) (PEO)–LiN(CF₃SO₂)₂ electrolyte system suppressed the crystallization of PEO, and improved the ionic conductivity at room temperature. Invited paper dedicated to Professor W. Weppner on his 65th birthday.     

Conductivity studies on PEO:NaClO3 electrolyte system with different plasticizers

A new ion conducting solid polymer electrolyte thin film based on Polyethylene oxide (PEO) with NaClO₃ salt is prepared by solution-casting method. The solvation of salt with PEO has been confirmed by X-ray diffraction and IR spectral studies. Plasticizer effects were studied in PEO:NaClO₃ system by using low molecular weight polyethylene glycol (PEG), dimethyl formamide (DMF) and propylene carbonate(PC). AC conductivity in the temperature range (308–378 K) was measured to evaluate the conductivity of the polymer electrolytes. From the conductivity data, it was found that the conductivity value of pure PEO increases 10²–10⁴ order of magnitude with the addition of salts as well as plasticizers. From the transference number experiments, it was confirmed that the charge transport in these electrolyte is mainly due to the ions (t_ion≈0.94). Finally, the conductivity value of all PEO: NaClO₃ systems were compared.     

PEO electrolytes containing dioctyl phthalate (DOP) for dye-sensitized nanocrystalline TiO2 solar cells

In this paper, we aim to prepare polymer electrolytes consisting of NaI and I₂ dissolved in poly(ethylene oxide) (PEO) and dioctyl phthalate (DOP) as an additive and apply the electrolytes to dye-sensitized solar cells (DSSC). Upon the incorporation of salt, the phthalic-stretching C=O bands of DOP in Fourier transform infrared spectra shifted to a lower wave number (Δf = 93 cm⁻¹), confirming the unusual strong complex formation between sodium ions and phthalic oxygen. Coordinative interactions and structural changes of PEO/NaI/I₂/DOP electrolytes have also been characterized by wide angle X-ray scattering, presenting an almost amorphous structure of the polymer electrolytes. The ionic conductivity of the polymer electrolytes reached ∼10^–4 S/cm at room temperature at the mole ratio of [EO]:[Na]:[DOP] = 10:1:0.5, as determined by the four-probe method. DSSC using the polymer electrolytes and conductive indium tin oxide glasses exhibited 2.9% of overall energy conversion efficiency (=P _max/P _in × 100) at one sun condition (100 mW/cm²). The good interfacial contact between the electrolytes and the dye-attached nanocrystalline TiO₂ layers were verified by field-emission scanning electron microscopy.     

Structural,electrical conductivity,and transport analysis of PAN–NH<Subscript>4</Subscript>Cl polymer electrolyte system

Poly (acrylonitrile) (PAN) and ammonium chloride (NH₄Cl)-based proton conducting polymer electrolytes with different compositions have been prepared by solution casting technique. The amorphous nature of the polymer electrolytes has been confirmed by XRD analysis. The FTIR analysis confirms the complex formation of the host polymer (PAN) with the salt (NH₄Cl). DSC measurements show a decrease in T_g with the increase in salt concentration. The conductivity analysis shows that the 25 mol% ammonium chloride doped polymer electrolyte has a maximum ionic conductivity, and it has been found to be 6.4 × 10^?3 Scm^?1, at room temperature. The temperature dependence of conductivity of the polymer electrolyte complexes appears to obey the Arrhenius nature. The activation energy (E_a = 0.23 eV) has been found to be low for 25 mol% salt doped polymer electrolyte. The dielectric behavior has been analyzed using dielectric permittivity (ε*), and the relaxation frequency (τ) has been calculated from the loss tangent spectra (tan δ). Using this maximum ionic conducting polymer electrolyte, the primary proton conducting battery with configuration Zn + ZnSO₄·7H₂O/75 PAN:25 NH₄Cl/PbO₂ + V₂O₅ has been fabricated and their discharge characteristics have been studied.