Surface functionalization of polystyrene to bind with FMRF peptides for novel biocompatibility

<正>A generic method was described to change surface biocompatibihty by introducing reactive functional groups onto surfaces of polymeric substrates and covalently binding them with biomolecules.A block copolymer with protected carboxylic acid functionality,poly(styrene-b-tert-butyl acrylate)(PS-PtBA),was spin coated from solutions in toluene on a bioinert polystyrene(PS) substrate to form a bilayer structure:a surface layer of the poly(tert-butyl acrylate)(PtBA) blocks that order at the air-polymer interface and a bottom layer of the PS blocks that entangle with the PS substrate.The thickness of the PtBA layer and the area density of tert-butyl ester groups of PtBA increased linearly with the concentration of the spin coating solution until a 2 nm saturated monolayer coverage of PtBA was achieved at the concentration of 0.4%W/W.The protected carboxylic acid groups were generated by exposing the tert-butyl ester groups of PtBA to trifluoroacetic acid (TFA) for bioconjugation with FMRF peptides via amide bonds.The yield of the bioconjugation reaction for the saturated surface was calculated to be 37.1%based on X-ray photoelectron spectroscopy(XPS) measurements.The success of each functionalization step was demonstrated and characterized by XPS and contact angle measurements.This polymer functionalization/modification concept can be virtually applied to any polymeric substrate by choosing appropriate functional block copolymers and biomolecules to attain novel biocompatibility.     

Interfacial reactions in confinement: kinetics and temperature dependence of the surface hydrolysis of polystyrene-block-poly(tert-butyl acrylate) thin films

The effect of confinement on the kinetics of the surface hydrolysis of polystyrene-block-poly(tert-butyl acrylate) (PS(n)-b-PtBA(m)) thin films on oxidized silicon substrates in 3 M aqueous hydrochloric acid was systematically investigated. As shown by X-ray photoelectron spectroscopy (XPS) and contact angle measurements, a skin layer of acid-sensitive PtBA is present on the surface of PS(n)-b-PtBA(m) films, consistent with the lower surface tension of PtBA compared to that of PS. The thickness of the skin layer was determined by angle-dependent XPS as approximately 8 nm for PS(690)-b-PtBA(1210). Tapping mode atomic force microscopy showed an increasing surface coverage of swollen poly(acrylic acid)-rich globules with increasing hydrolysis time. Using ex situ Fourier transform infrared spectroscopy, the reaction kinetics was determined quantitatively as a function of temperature, polymer film thickness, thermal pretreatment of the films, and block copolymer composition. The initial stages of the hydrolysis can be described as a pseudo-first-order reaction under all conditions investigated. The corresponding rate constants were found to be 2 orders of magnitude lower than those reported for the hydrolysis of tert-butyl acetate in solution and depended linearly on the fraction of PtBA exposed at the surface. However, the polymer film thickness, thermal pretreatment of the films, block copolymer composition, and local composition did not affect the rate constants. The negative value of the activation entropy (DeltaS(298)++ = -103 J/mol K), determined according to the Arrhenius equation and transition state theory, indicates that the tightness of the transition state is more pronounced in the PS(n)-b-PtBA(m) film compared to reactions in solution. Thus, the spatial constraints due to the incorporation of the reactive ester groups in thin polymer films are responsible for the observed reduced reactivity.     

A surface-reactive rod-coil diblock copolymer: nano- and micropatterned polymer brushes.

A diblock copolymer consisting of poly(3-(triethoxysilyl)propylisocyanate) (PIC) and polystyrene(PS) was synthesized by anionic polymerization. A polymeric monolayer of the block copolymer was formed on silica substrates by various grafting techniques such as immersion, casting, or contact-printing. The PIC block adheres covalently to Si substrates in an in-plane fashion due to its extended rodlike conformation and reactivity to the silica. The polystyrene blocks aggregate to form mounds on the surface resulting in a new type of nanopatterned polymer brush. The self-limiting adsorption of the rod coils results in a thickness of about 5 nm regardless of the solution concentration and coating method. This particular property allowed microcontact printing directly onto silicon or glass substrates. The resulting surface morphology consisted of nanoscale domains given by the block copolymer and uniform thickness micropatterns transferred from the stamp within the printed area. This study offers a simple new method to prepare a covalent polymeric monolayer with nano- and micropatterns, which can be performed directly onto various silicon-based substrates.     

"Click-functional" block copolymers provide precise surface functionality via spin coating

There are few existing methods for the quantitative functionalization of surfaces, especially for polymeric substrates. We demonstrate that alkyne end-functional diblock copolymers can be used to provide precise areal densities of reactive functionality on both hard (e.g., glass and silicon oxide) and soft (i.e., polymeric) substrates. Alkyne functionality is extremely versatile because the resultant functional surfaces are reactive toward azide functional molecules by Sharpless click chemistry. Spin-coated films of alpha-alkyne-omega-Br-poly( tert-butylacrylate- b-methylmethacrylate) (poly( tBA-MMA)) spontaneously self-assemble on the aforementioned substrates to present a surface monolayer of PtBA with a thickness in the range of 1 to 9 nm. The PMMA block physisorbs to provide multivalent anchoring onto hard substrates and is fixed onto polymer surfaces by interpenetration with the substrate polymer. The areal density of alkyne functional groups is precisely controlled by adjusting the thickness of the block copolymer monolayer, which is accomplished by changing either the spin coating conditions (i.e., rotational speed and solution concentration) or the copolymer molecular weight. The reactivity of surface-bound alkynes, in 1,3-dipolar cycloaddition reactions or by so-called "click chemistry", is demonstrated by covalent surface immobilization of fluorescently labeled azides. The modificed surfaces are characterized by atomic force microscopy (AFM), contact angle, ellipsometry, fluorescent imaging and angle-dependent X-ray photoelectron spectroscopy (ADXPS) measurements. Microarrays of covalently bound fluorescent molecules are created to demonstrate the approach and their performance is evaluated by determining their fluorescence signal-to-noise ratios.     

Conformational change in an isolated single synthetic polymer chain on a mica surface observed by atomic force microscopy

The random coil conformation of an isolated conventional synthetic polymer chain was clearly imaged by atomic force microscopy (AFM). The sample used was a poly(styrene)-block-poly(methyl methacrylate) diblock copolymer. A very dilute solution of the copolymer with benzene was spread on a water surface. The structure thus formed on water was subsequently transferred and deposited onto mica at various surface pressures and observed under AFM. The AFM images obtained with films deposited at a low surface pressure (<0.1 mN/m) showed a single polystyrene (PS) block chain aggregated into a single PS particle with a single poly(methyl methacrylate) (PMMA) block chain emanating from the particle. Immediately after the deposition, the single PMMA block chain aggregated to form a condensed monolayer around the polystyrene particles. However, after exposing the deposited film to highly humid air for 1 day, the PMMA chains spread out so that the single PMMA block chain could be identified as a random coil on the substrate. The thin water layer formed on the mica substrate in humid air may enable the PMMA block chain to be mobilized on the substrate, leading to the conformational rearrangement from the condensed monolayer conformation to an expanded and elongated coil. The elongation of the PMMA chain was highly sensitive to the humidity; the maximum elongation was obtained at 79% relative humidity. The elongation was a slow process and took about 20 h.     

Solid-supported block copolymer membranes through interfacial adsorption of charged block copolymer vesicles

The properties of amphiphilic block copolymer membranes can be tailored within a wide range of physical parameters. This makes them promising candidates for the development of new (bio)sensors based on solid-supported biomimetic membranes. Here we investigated the interfacial adsorption of polyelectrolyte vesicles on three different model substrates to find the optimum conditions for formation of planar membranes. The polymer vesicles were made from amphiphilic ABA triblock copolymers with short, positively charged poly(2,2-dimethylaminoethyl methacrylate) (PDMAEMA) end blocks and a hydrophobic poly( n-butyl methacrylate) (PBMA) middle block. We observed reorganization of the amphiphilic copolymer chains from vesicular structures into a 1.5+/-0.04 nm thick layer on the hydrophobic HOPG surface. However, this film starts disrupting and dewetting upon drying. In contrast, adsorption of the vesicles on the negatively charged SiO2 and mica substrates induced vesicle fusion and formation of planar, supported block copolymer films. This process seems to be controlled by the surface charge density of the substrate and concentration of the block copolymers in solution. The thickness of the copolymer membrane on mica was comparable to the thickness of phospholipid bilayers.     

One-step route to the fabrication of highly porous polyaniline nanofiber films by using PS-b-PVP diblock copolymers as templates

We report a new method to control both the nucleation and growth of highly porous polyaniline (PANI) nanofiber films using porous poly(styrene-block-2-vinylpyridine) diblock copolymer (PS-b-P2VP) films as templates. A micellar thin film composed of P2VP spheres within a PS matrix is prepared by spin coating a PS-b-P2VP micellar solution onto substrates. The P2VP domains are swollen in a selective solvent of acetic acid, which results in the formation of pores in the block copolymer film. PANI is then deposited onto the substrates modified with such a porous film using electrochemical methods. During the deposition, the nucleation and growth of PANI occur only at the pores of the block copolymer film. After the continued growth of PANI by the electrochemical deposition, a porous PANI nanofiber film is obtained.     

Environmentally responsive "hairy" nanoparticles: mixed homopolymer brushes on silica nanoparticles synthesized by living radical polymerization techniques

This article reports on the preparation of environmentally responsive "hairy" nanoparticles by growth of mixed poly(tert-butyl acrylate) (PtBA)/polystyrene (PS) brushes from silica particles using living radical polymerization techniques and subsequent hydrolysis of PtBA to produce amphiphilic mixed poly(acrylic acid) (PAA)/PS brushes. Silica particles were synthesized by the Stober process and were functionalized with an asymmetric difunctional initiator-terminated monolayer. Surface-initiated atom transfer radical polymerization of tBA was carried out in the presence of a free initiator. Kinetics study showed that the polymerization was well controlled. By cleaving PtBA off the particles, the molecular weights of the grafted and free polymers were found to be essentially identical. Mixed PtBA/PS brushes were obtained by the nitroxide-mediated radical polymerization of styrene from PtBA particles. The M(n) of the grafted PS was found to be the same as that of the free PS formed in the solution from the free initiator. Amphiphilic mixed PAA/PS brush-coated nanoparticles were synthesized from mixed PtBA/PS particles by hydrolysis of PtBA with iodotrimethylsilane. Tyndall scattering experiments and (1)H NMR study showed that the mixed PAA/PS particles can be dispersed and form a stable suspension in CHCl(3), a selective solvent for PS, and also in CH(3)OH, a selective solvent for PAA, demonstrating the capability of these hairy nanoparticles to undergo chain reorganization in response to environmental changes.     

Stimuli-responsive polyelectrolyte block copolymer brushes synthesized from the Si wafer via atom-transfer radical polymerization

Surface-tethered oppositely charged weak polyelectrolyte block copolymer brushes composed of poly(2-vinyl pyridine) (P2VP) and poly(acrylic acid) (PAA) were grown from the Si wafer by atom-transfer radical polymerization. The P2VP-b-PAA brushes were prepared through hydrolysis of the second PtBA block to the corresponding acrylic acid. The P2VP-b-PAA brushes with different PAA block length were obtained. The P2VP-b-PAA brushes revealed a unique reversible wetting behavior with pH. The difference between the solubility parameters for P2VP and PAA, the changes of surface chemical composition and surface roughness, and the reversible wetting behavior illustrated that the surface rearrangement occurred during treatment of the P2VP-b-PAA brushes by aqueous solution with different pH value. The reversible properties of the P2VP-b-PAA brushes can be used to regulate the adsorption of the sulfonated PS nanoparticles.     

Compositional Mapping of Polymer Surfaces by Chemical Force Microscopy Down to the Nanometer Scale: Reactions in Block Copolymer Microdomains

The laterally resolved analysis of the chemical surface composition of surface-treated block copolymers by atomic force microscopy (AFM) pull-off force mapping in the force volume (FV) mode and the automated analysis of the FV data is discussed. Poly(tert-butyl acrylate) (PtBA) microdomains residing in a polystyrene (PS) matrix at the surface of cyclohexane-treated polystyrene-block-poly(tert-butyl acrylate) (PtBA-b-PS) block copolymer thin films were domain-selectively deprotected, activated and chemically modified, as also shown by fluorescence microscopy. AFM pull-off force mapping in conjunction with an automated analysis of the data provided real space evidence for the successful conversion of reactive esters located in the PtBA domains and showed that AFM and related approaches, such as chemical force microscopy (CFM), can indeed contribute to assess changes in heterogeneous surface chemical composition of polymers down to sub-50 nm length scales.     

Transmission electron microscopy study of solvent-induced phase morphologies of environmentally responsive mixed homopolymer brushes on silica particles

We report in this work a transmission electron microscopy study of phase morphologies of environmentally responsive mixed poly( t-butyl acrylate) (P tBA)/polystyrene (PS) brushes and mixed poly(acrylic acid) (PAA)/PS brushes on 180 nm silica particles after treatments with nonselective good solvents and selective solvents, respectively. Mixed P tBA/PS brushes were grown from Y-initiator-functionalized silica particles by sequential atom transfer radical polymerization and nitroxide-mediated radical polymerization. Mixed PAA/PS brushes were prepared from mixed P tBA/PS brushes by removal of the t-butyl groups. For mixed P tBA/PS brushes with P tBA M n of 24.2 kDa and PS M n of 23.0 kDa and the corresponding mixed PAA/PS brushes, random worm-like, nearly bicontinuous nanostructures were formed from lateral microphase separation when the particles were cast from nonselective good solvents (chloroform for mixed P tBA/PS brushes and N, N-dimethylformamide for mixed PAA/PS brushes). The feature sizes were on the order of polymer chain root-mean-square end-to-end distances ( approximately 10 nm). In contrast, mixed P tBA/PS brushes with lower molecular weights (P tBA M n = 10.4 kDa and PS M n = 11.9 kDa) did not strongly phase separate after being cast from chloroform. After the solvents in the particle dispersions were gradually changed to selective solvents ( n-octane for mixed P tBA/PS brushes and H 2O for mixed PAA/PS brushes), isolated microdomains with an average size of 14-19 nm were formed as one grafted polymer collapsed and associated to form isolated microdomains, which were shielded by another grafted polymer yielding surface-tethered micellar structures. These results confirmed the theoretical predictions of the formation of "rippled" nanostructures and surface micellar structures of mixed homopolymer brushes induced by nonselective and selective solvents, respectively.     

Equilibrium and dynamics of Langmuir monolayers when the interface is a selective solvent: Polystyrene-b-poly(t-butyl acrylate) block copolymers

The surface pressure of monolayers of insoluble diblock copolymers has been measured. One of the blocks is made of poly(t-butyl acrylate) (PtBA), and the other one by polystyrene (PS). The interface is a good solvent for PtBA, while it is a poor solvent for PS. For the sake of comparison, monolayers of a PtBA homopolymer (good solvent conditions) and of poly(4-hydroxy styrene) (P4HS) (poor solvent conditions) have been also measured. It has been found that the relative length of the blocks plays an important role on the shape of the surface pressure Pi versus surface concentration Gamma curves and also on the shape of the equilibrium compressibility versus Gamma curves. However, it does not affect the maximum value of Pi reached at high Gamma's. Surprisingly, the ellipsometric thickness of the copolymer monolayers is almost independent of the relative length of the blocks. The dynamics of the monolayers has been studied by step compression and by surface-light scattering techniques. When M(w,PtBA) > M(w,PS) single exponential relaxations are observed. However, stretched exponentials are obtained for M(w,PS) > or = M(w,PtBA). The relaxation times decrease with increasing Gamma for all the copolymers studied. This is the behavior usually found for poor solvent conditions (P4HS) and opposite to that found for homopolymers under good solvent conditions [PtBA, poly(vinylacetate)]. This means that the solvent quality of the interface does not determine the pressure dependence of tau. The elasticity modulus of the monolayers in the kilohertz range takes values that are similar to those of the high-frequency limit of the relaxation experiments. This means that the relaxation processes have characteristic frequencies below 1 Hz.     

Preparation of end-grafted polymer brushes by nitroxide-mediated free radical polymerization of vaporized vinyl monomers

In this work, we report a gas-phase polymerization approach to create end-grafted vinyl based polymer films on silicon oxide based substrates. The "surface-initiated vapor deposition polymerization" (SI-VDP) of vaporized vinyl monomers, via the nitroxide-mediated free radical polymerization mechanism, was developed to fabricate various homo- and block copolymer brushes from surface-bound initiators, 1-(4'-oxa-2'-phenyl-12'-trimethoxysilyldodecyloxy)-2,2,6,6-tetra-methylpiperidine ("TEMPO"). The resulting polymer thin films were characterized by the Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, ellipsometry, and contact angle goniometry, respectively, to identify the surface composition, film thickness, surface coverage, and water contact angles. Through the SI-VDP, end-grafted polymer films of polystyrene (PSt), poly(acrylic acid) (PAAc), poly(N-(2-hydroxypropyl) methacrylamide) (PHPMA), and poly(N-isopropylacrylamide) (PNIPAAm) with 10-200 nm thicknesses were fabricated. Furthermore, the block copolymer films of PAAc (1st block)-b-PSt (2nd block), PSt (1st block)-b-PAAc (2nd block), and a triblock copolymer film of PAAc (1st)-b-PSt (2nd)-b-PHPMA (3rd), were also fabricated, suggesting the "renewability" of the TEMPO-initiated polymerization in the SI-VDP scheme. It is also noticed that the SI-VDP is more efficient than the conventional solution phase polymerization in producing functional polymer brushes such as PNIPAAm, PAAc, or PAAc-b-PSt end-grafted films. In summary, our studies have shown clear advantages of the SI-VDP setup for the nitroxide-mediated polymerization scheme in controlling synthesis of end-grafted homo- and copolymer thin films.     

聚苯乙烯-聚(4-乙烯基吡啶)嵌段共聚物LB膜结构形态的研究

采用氯仿作为铺展溶剂,将嵌段共聚物聚苯乙烯-聚(4-乙烯基吡啶)(PS-b-P4VP)稀溶液铺展于空气与水界面上,利用Langmuir-Blodgett(LB)膜技术转移至固体基底.研究了不同的嵌段比、表面压和小分子1-芘丁酸(PBA)的加入对嵌段共聚物气液界面聚集组装的影响.研究发现随着亲水段(P4VP)的增加,聚集组装结构由纳米片状、带状转变成纳米条状、纳米点状结构.表面压对纯PS-b-P4VP聚集组装产生影响,表面压增大,组装体排列紧密;随着表面压的继续增大,单层聚集结构遭到破坏,发生堆叠.加入PBA小分子后,PBA与PS-b-P4VP形成氢键,形态发生明显变化,原来的片状结构转变为条状或点状结构.     

Polymer‐Coated PtCo Nanoparticles Deposited on Diblock Copolymer Templates: Chemical Selectivity versus Topographical Effects

Metal–polymer hybrid films are prepared by deposition of polymer‐coated PtCo nanoparticles onto block copolymer templates. For templating, a thin film of the lamella‐forming diblock copolymer poly(styrene‐b‐methyl methacrylate) P(S‐b‐MMA) is chemically etched and a topographical surface relief with 3 nm height difference is created. Two types of polymer‐grafted PtCo nanoparticles are compared to explore the impact of chemical selectivity versus the topographical effect of the nanotemplate. A preferable wetting of the polystyrene (PS) domains with poly(styrenesulfonate) (PSS)‐coated PtCo nanoparticles (instead of residing in the space between the domains) is observed. Our investigation reveals that the interaction between PSS‐coated nanoparticles and PS domains dominates over the topographical effects of the polymer surface. In contrast, a non‐selective deposition of poly(N‐vinyl‐2‐pyrrolidone) (PVP)‐coated PtCo nanoparticles and the formation of large metal‐particle aggregates on the film is observed.     

Creating surfactant nanoparticles for block copolymer composites through surface chemistry

A simple strategy to tailor the surface of nanoparticles for their specific adsorption to and localization at block copolymer interfaces was explored. Gold nanoparticles coated by a mixture of low molecular weight thiol end-functional polystyrene (PS-SH) (Mn = 1.5 and 3.4 kg/mol) and poly(2-vinylpyridine) homopolymers (P2VP-SH) (Mn = 1.5 and 3.0 kg/mol) were incorporated into a lamellar poly(styrene-b-2-vinylpyridine) diblock copolymer (PS-b-P2VP) (Mn = 196 kg/mol). A library of nanoparticles with varying PS and P2VP surface compositions (FPS) and high polymer ligand areal chain densities was synthesized. The location of the nanoparticles in the PS-b-P2VP block copolymer was determined by transmission electron microscopy. Sharp transitions in particle location from the PS domain to the PS/P2VP interface, and subsequently to the P2VP domain, were observed at FPS = 0.9 and 0.1, respectively. This extremely wide window of FPS values where the polymer-coated gold nanoparticles adsorb to the interface suggests a redistribution of PS and P2VP polymers on the Au surface, inducing the formation of amphiphilic nanoparticles at the PS/P2VP interface. In a second and synthetically more challenging approach, gold nanoparticles were covered with a thiol terminated random copolymer of styrene and 2-vinylpyridine synthesized by RAFT polymerization. Two different random copolymers were considered, where the molecular weight was fixed at 3.5 kg/mol and the relative incorporation of styrene and 2-vinylpyridine repeat units varied (FPS = 0.52 and 0.40). The areal chain density of these random copolymers on Au is unfortunately not high enough to preclude any contact between the P2VP block of the block copolymer and the Au surface. Interestingly, gold nanoparticles coated by the random copolymer with FPS = 0.4 were dispersed in the P2VP domain, while those with FPS = 0.52 were located at the interface. A simple calculation for the adsorption energy to the interface of the nanoparticles with different surface arrangements of PS and P2VP ligands supports evidence for the rearrangement of thiol terminated homopolymers. An upper limit estimate of the adsorption energy of nanoparticles uniformly coated with a random arrangement of PS and P2VP ligands where a 10% surface area was occupied by P2VP -mers or chains was approximately 1 kBT, which indicates that such nanoparticles are unlikely to be segregated along the interface, in contrast to the experimental results for nanoparticles with mixed ligand-coated surfaces.     

Ellipsometric study of adsorption on nanopatterned block copolymer substrates

We report ellipsometrically obtained adsorption isotherms for a carefully chosen test liquid on block copolymer films of Kraton G1650, compared with adsorption isotherms on homogeneous films of the constituent polymers. Standard atomic force microscopy images imply the outer surface of Kraton G1650 is chemically patterned on the nanoscale, but this could instead be a reflection of structure buried beneath a 10 nm layer of the lower energy component. Our test liquid was chosen on the basis that it did not dissolve in either component and in addition that it was nonwetting on the lower energy polymer while forming thick adsorbed films on pure substrates of the higher energy component. Our ellipsometry data for Kraton G1650 rule out the presence of segregation by the lower energy constituent to the outer surface, implying a mixed surface consistent with Cassie's law. We discuss implications of our findings and related work for the outer surface structures of block copolymer films.     

Fabrication of nanoporous templates from diblock copolymer thin films on alkylchlorosilane-neutralized surfaces

The fabrication of nanoporous templates from poly(styrene)-b-poly(methyl methacrylate) diblock copolymer thin films (PS-b-PMMA, volume ratio 70:30) on silicon requires precise control of interfacial energies to achieve a perpendicular orientation of the PMMA cylindrical microdomains relative to the substrate. To provide a simple, rapid, yet tunable approach for surface neutralization, we investigated the self-assembled ordering of PS-b-PMMA diblock copolymer thin films on silicon substrates modified with a partial monolayer of octadecyldimethyl chlorosilane (ODMS), i.e., a layer of ODMS with a grafting density less than the maximum possible monolayer surface coverage. We demonstrate herein the fabrication of nanoporous PS templates from annealed PS-b-PMMA diblock copolymer thin films on these partial ODMS SAMs.     

The morphology and structure of PS‐b‐P4VP block copolymer films by solvent annealing: effect of the solvent parameter

Lamellae (symmetric) forming polystyrene‐b‐poly(4‐vinylpyridine) (PS‐b‐P4VP) block copolymers (BCPs) were used to produce nanostructured thin films by solvent (toluene) casting (spin‐coating) onto silicon substrates. As expected, strong micellization of PS‐P4VP in toluene results in poorly ordered hexagonally structures films. Following deposition the films were solvent annealed in various solvents and mixtures thereof. A range of both morphologies including micelle and microphase separated structures were observed. It was found that nanostructures typical of films of regular thickness (across the substrate) and demonstrating microphase separation occurred only for relatively few solvents and mixtures. The data demonstrate that simple models of solvent annealing based on swelling of the polymer promoting higher polymer chain mobility are not appropriate and more careful rationalization is required to understand these data. Analysis suggests that regular phase separated films can only be achieved when the copolymer Hildebrand solubility parameter is very similar to the value of the solvent. It is suggested that the solvent anneal method used is best considered as a liquid phase technique rather than a vapor phase method. The results show that solvent annealing methods can be a very powerful means to control structure and in some circumstances dominate other factors such as surface chemistry and surface energies. Copyright © 2009 John Wiley & Sons, Ltd.     

Hydrophobic monolayer preparation by Langmuir-Blodgett and chemical adsorption techniques

Alkylsiloxane and perfluoroalkylsiloxane monolayers are prepared on siliceous surfaces using the techniques of Langmuir-Blodgett deposition and solid-liquid chemical adsorption. Acid-catalyzed hydrolysis and polycondensation reactions provide two-dimensional siloxane networks at the liquid-vapor interface, which can be compressed to mean molecular areas of approximately 22 and approximately 32 A(2) for pendent hydrocarbon and fluorocarbon chains, respectively. Subsequent Langmuir-Blodgett transfer onto glass substrates at moderate surface pressures leads to compact monolayers for single-component precursors, while mixed alkyl- and perfluoroalkylsilanes produce nonhomogeneous films characterized by transfer ratios greater than unity. As an alternate monolayer preparation technique, silane polymerization was performed directly on siliceous surfaces via a chemical adsorption mechanism. XPS analysis of a chemically adsorbed 1H,1H,2H,2H-perfluorodecylsiloxane film confirms a single adsorbed monolayer thickness in which the pendent fluoroalkyl chains align nonperpendicularly with respect to the surface. The surface free energy was determined to be 11.4 dyn cm(-1) based on static contact angle measurements. AFM imaging shows the presence of surface defects due to oligomer deposition during the drying process. The use of solubilized trichloro-based silane coupling agents under anhydrous conditions is shown to produce surfaces with a minimal number of surface defects. The presence of undissolved silane material in the bulk solution significantly increases the number of surface defects.