Determination of mercury in environmental samples by cold vapour generation and atomic-absorption spectrometry with a gold-coated graphite furnace

Mercury is determined at below the pg/ml level by a combination of cold vapour generation, trapping in a gold-coated graphite furnace and atomic-absorption detection. The mercury is reduced to the element by stannous chloride, stripped from solution by a stream of nitrogen and collected on a gold-coated porous graphite disk in a graphite furnace. It is then atomized by increasing the graphite furnace temperature and detected by an atomic-absorption spectrophotometer. The absolute detection limit and the characteristic mass were found to be 5 and 20 pg for 0.0044 absorbance, respectively. The concentration limit of detection was 0.1 pg/ml for a 50-ml sample, and the linear dynamic range covered three orders of magnitude. The precisions of the measurements were 2.7% for 0.1 ng and 2.6% for 2 ng of mercury. Analyses of NBS and NIES reference materials showed quantitative recovery. Analytical results obtained by the technique are presented for natural waters, marine biota and sediments.     

Determination of mercury in environmental and biological samples by cold vapour atomic absorption spectrometry

A continuously operating monitoring method for total mercury at sub-ng/ml level in environmental and biological samples by cold vapour atomic-absorption spectrometry with NaBH₄ as a reductant was developed. The mercury vapour generator and absorption cell closed-end by quartz were used in this study. The detection limit (S/N = 3) and relative standard deviation of 12 determinations of 10 ng/ml Hg(II) were 0.11 ng/ml and 1.1%, respectively. The range of standard calibration curve was 0–50 ng/ml Hg, The proposed method was successfully applied to the completely continuous monitoring of total mercury in waste water, sediments and pork liver.     

Determination of total mercury in coal fly ash by gold amalgamation cold vapour atomic absorption spectrometry

A method for the determination of total mercury in coal fly ash by gold amalgamation cold vapour atomic absorption spectrometry (CV-AAS) was optimized. Most of the experiments were performed on NBS SRM 1633a Coal Fly Ash with a certified value of 160 ± 10 ng Hg g^?1. The main attention was focused on the decomposition of the sample. The efficacy of pressure decompositions in closed silica and sealed Pyrex tubes using various combinations of acids (HNO₃, HCl, HClO₄) was compared with oxidative combustion of the coal fly ash. Notwithstanding the incomplete mineralization of the sample in sealed tubes, the results obtained showed good agreement with the certified value and results obtained by neutron activation analysis (NAA), which suggests that mercury is quantitatively released from the sample into solution. Lower results were obtained using decomposition in closed (but not hermetically sealed) silica tubes owing to losses of mercury by volatilization during decomposition. Interferences from some metal ions (nickel, lead, copper, silver, palladium, zinc and antimony) were also examined. The results showed a serious depression of the mercury signal only when gold, palladium and platinum were present at higher concentrations, which never or very seldom occur in fly ash matrices, and therefore do not represent a limitation of the method.     

Determination of mercury in seawater by cold vapour atomic absorption spectrophotometry

Summary To avoid systematic errors in the sampling and determination of mercury in seawater an integrated sampling-analyzing system has been developed. A 500 ml PTFE-bottle attached to a sampling gear is used as sampling vessel for the cold vapour atomic absorption Spectrophotometry, using nitrogen aeration, SnCl₂ reduction, and preenrichment/ purification by amalgamation on finely dispersed gold. The detection limit of this procedure was found to be 0.5 ng·l^–1 and the coefficient of variation 4% for 1.5 ng·l^–1.

---

Bestimmung von Quecksilber im Meerwasser durch Kaltdampf-Atomabsorptionsspektralphotometrie

Zusammenfassung Zur Vermeidung von systematischen Fehlern bei der Ultraspurenanalyse von Quecksilber im Meerwasser wurde ein integriertes Probenahme-Analysensystem entwickelt. Eine 500 ml PTFE-Flasche dient in Verbindung mit einem Greifarm als Probenahmegefäß für Oberflächenwasser und wird anschließend als Reaktionsgefäß in die Analysenapparatur gesetzt. Die Bestimmung erfolgt mit der Kaltdampf-Atomabsorptionsspektralphotometrie nach Reduktion des Quecksilbers durch SnCl₂ und Anreicherung sowie Reinigung mittels Amalgamierung an feinverteiltem Gold. Die Nachweisgrenze dieses Verfahrens beträgt 0,5 ng·l^–1, der Variationskoeffizient 4% bei 1,5 ng·l^–1.

     

Determination of total mercury in environmental and biological samples by flow injection cold vapour atomic absorption spectrometry

A simple and accurate method has been developed for the determination of total mercury in environmental and biological samples. The method utilises an off-line microwave digestion stage followed by analysis using a flow injection system with detection by cold vapour atomic absorption spectrometry.

The method has been validated using two certified reference materials (DORM-1 dogfish and MESS-2 estuarine sediment) and the results agreed well with the certified values. A detection limit of 0.2 ng g⁻¹ Hg was obtained and no significant interference was observed. The method was finally applied to the determination of mercury in river sediments and canned tuna fish, and gave results in the range 0.1–3.0 mg kg⁻¹.     

Determination of mercury by atomic-absorption spectrophotometry

A flameless atomic-absorption system has been developed for the determination of low concentrations of mercury in gaseous, solid and liquid samples of organic and inorganic materials.     

Determination and speciation of mercury in a dental work-place by cold vapour atomic absorption spectrometry and gas-liquid chromatography

Cold Vapour Atomic Absorption Spectrometry (CVAAS) and Gas-Liquid Chromatography (GLC) have been used for determination and speciation of mercury. Total mercury, methylmercury, ethylmercury and phenylmercury concentrations in urine samples taken from students and staff of a dental work-place were investigated. Air samples were also analyzed. Detection limits, as three times the standard deviation, and in units of ng analyte per ml urine were found to be 1.7, 12, 2.4 and 21 for total mercury, methylmercury chloride, ethylmercury chloride and phenylmercury chloride, respectively.     

Sensitive determination of gaseous mercury in air by cold vapour atomic fluorescence spectrometry after amalgamation

A method was developed for the determination of mercury in air, using preconcentration by amalgamation on gold absorbers followed by measurement by atomic fluorescence spectrometry (AFS). The system has a detection limit of ca. 2.0 pg and the precision is in the range 5–10% (relative standard deviation). The accuracy was confirmed by comparison with cold vapour atomic absorption spectrometry. The method was applied to the determination of gaseous mercury in both indoor and outdoor air. As a result of the sensitivity small sample volumes can be analysed and only short sampling times are required. The method is thus suitable for continuous monitoring of mercury and for the fast and reliable determination of gaseous mercury in the atmosphere, even at background levels.     

Determination of germanium by graphite-furnace atomic-absorption spectrometry

The premature loss of germanium as volatile GeO results in low sensitivity and poor reproducibility in the determination of germanium by graphite-furnace atomic-absorption spectrometry. This interference can be eliminated by suppressing the premature reduction of GeO(2) to GeO during the ashing step, and dissociating the germanium oxides into the atoms simultaneously with their vaporization during the atomization step. The premature reduction of GeO(2) to GeO has been successfully prevented by several approaches: (1) diminishing the reducing activity of the graphite furnace by (a) oxidizing the graphite surface and intercalating oxygen into the graphite lattice with oxidizing acids, such as nitric or perchloric, in the sample solution, or (b) using a tantalum-treated graphite furnace; (2) keeping the analyte as germanium (IV) by addition of sodium or potassium hydroxide to the sample solutions.     

On-line preconcentration of inorganic mercury and methylmercury in sea-water by sorbent-extraction and total mercury determination by cold vapour atomic absorption spectrometry

A comparative study of three mercury chelate forming reagents [diethyldithiocarbamate, pyrrolidin-1-yldithioformate and diphenylthiocarbazone (dithizone)] has been carried out for the preconcentration of ultratrace amounts of inorganic mercury and methylmercury in silica C(18) minicolumns as the solid sorbent. Sample flow injection in-line sorbent extraction was coupled with continuous cold vapour atomic absorption spectrometry (CVAAS) for detection. Results showed the superiority of the carbamate type reagents over the dithizone for the on-line formation and preconcentration of the corresponding mercury chelates. Using diethyldithiocarbamate (DDC) as reagent, aqueous sample volumes of 100 ml can be preconcentrated with 100% efficiency for both inorganic mercury and methylmercury. Quantitative release of the retained DDC chelates was obtained for volumes of eluent (ethanol) of 50 microl. Following the proposed procedure, detection limits of 16 ng/l. of mercury were achieved for sample volumes of 25 ml. The relative standard deviation was +/- 3.4% at 0.5 microg/l. Hg(II) levels. The method has been successfully applied to the determination of low levels of mercury in sea-water.     

Determination of mercury in carbon black by cold vapor atomic absorption spectrometry

Recently, a new color additive, D&C Black No. 2, a high-purity furnace black in the general category of carbon blacks, was listed as a color subject to batch certification by the U.S. Food and Drug Administration. A simple procedure was developed to determine mercury (Hg) in D&C Black No. 2, which is limited by specification to not more than 1 ppm Hg. The method uses partial acid digestion followed by cold vapor atomic absorption and was developed by modifying a method used for other color additives. The carbon black samples are treated with a mixture of nitric and hydrochloric acids and heated by microwave in sealed Teflon vessels. The resulting solutions, which are stable to Hg loss for at least 1 week, are diluted and analyzed for Hg using cold vapor atomic absorption spectrometry. Validation was performed by spiking carbon black samples with inorganic Hg (HgNO3) at levels from 0.1 to 1.5 microg/g, and by analyzing 2 standard reference materials. At the specification level of 1 ppm Hg (1 microg Hg/g), the 95% confidence interval was +/-0.01 ppm Hg (0.01 microg Hg/g). The method developed in this study gave good results for very difficult-to-analyze materials, such as coal standard reference materials and carbon black. By eliminating volatility and adsorption factors through the formation of HgCl4(-2) complexes, one can avoid using extremely hazardous acids such as HF and HClO4.     

Digestion method for the determination of mercury in vegetable matrices by cold vapour atomic absorption spectrometry

A simple and rapid wet-digestion procedure is described for the determination of total mercury in botanical samples by cold vapour atomic absorption spectrometry. The method is based on the oxidising properties of potassium dichromate in dilute sulphuric acid and was tested on two National Institute of Standards and Technology Standard Reference Materials. The mass of the samples taken for analysis was about 0.5 g in all instances, corresponding to an amount of mercury of the order of 0.075-0.040 micrograms depending on the material. The results were compared with those obtained using the Association of Official Analytical Chemists official digestion technique, which involves the use of nitric and sulphuric acids, and a second technique based on the action of nitric and perchloric acids. The proposed method provided better accuracy and showed good precision. Its ability to achieve the decomposition of two organomercurials for full mercury recovery was verified.     

Determination of total urinary mercury by on-line sample microwave digestion followed by flow injection cold vapour inductively coupled plasma mass spectrometry or atomic absorption spectrometry

The total mercury content in urine was determined by inductively coupled plasma mass spectrometry with the so-called cold vapour method after on-line oxidative treatment of the sample in a microwave oven (FI-MW-CV-ICPMS). Use of a KBr/KBrO(3) mixture, microwave digestion, and the final oxidation with KMnO(4), assure the complete recovery of the organic forms of Hg which would be difficult to determine otherwise if using only the CV-ICPMS apparatus. Quantitative recoveries were obtained for phenyl Hg chloride (PMC), dimethyl Hg (DMM), Hg acetate (MA) and methyl Hg chloride (MMC). Use of automatic flow injection microwave systems (FI-MW) for sample treatment reduces environmental contamination and allows detection limits suitable for the determination of reference values. Since no certified reference materials were commercially available in the concentration ranges of interest, the accuracy of the proposed procedure has been assessed by analysing a series of urine samples with two independent techniques, ICP-MS and AAS. When using the FI-MW-CV-ICP-MS technique, the detection limit was assessed at 0.03microg/L Hg, while with FI-MW-CV-AAS it was 0.2microg/L Hg. The precision of the method was less than 2-3% for FI-MW-CV-ICP-MS and about 3-5% for FI-MV-CV-AAS at concentrations below 1microg/L Hg. These results show that ICP-MS can be considered as a "reference technique" for the determination of total urinary Hg at very low concentrations, such as are present in non-exposed subjects.     

Total and inorganic mercury determination in fish tissue by flow injection cold vapour atomic fluorescence spectrometry

A simple and reliable method for Hg determination in fish samples has been developed. Lyophilised fish tissue samples were extracted in a 25% (w/v) tetramethylammonium hydroxide (TMAH) solution; the extracts were then analysed by FI-CVAFS. This method can be used to determine total and inorganic Hg, using the same FI manifold. For total Hg determination, a 0.1% (w/v) KMnO₄ solution was added to the FI manifold at the sample zone, followed by the addition of a 0.5% (w/v) SnCl₂ solution, whereas inorganic Hg was determined by adding a 0.1% (w/v) L-cysteine solution followed by a 1.0% (w/v) SnCl₂ solution to the FI system. The organic fraction was determined as the difference between total and inorganic Hg. Sample preparation, reagent consumption and parameters that can influence the FI-CVAFS performance were also evaluated. The limit of detection for this method is 3.7 ng g^?1 for total Hg and 4.3 ng g^?1 for inorganic Hg. The relative standard deviation for a 1.0 µg L^?1 CH₃Hg standard solution (n = 20) was 1.1%, and 1.3% for a 1.0 µg L^–1 Hg²⁺ standard solution (n = 20). Accuracy was assessed by the analysis of Certified Reference Material (dogfish: DORM-2, NRCC). Recoveries of 99.1% for total Hg and 93.9% inorganic Hg were obtained. Mercury losses were not observed when sample solutions were re-analysed after a seven day period of storage at 4°C.     

Determination of aluminium in aerosols by flameless atomic-absorption spectrometry

A method is reported for the determination of aluminium in aerosols collected on Whatman 41 cellulose filters. In the destruction procedure, provision was made to eliminate silica by hydrofluoric acid treatment. Analysis of the solutions was performed by the flameless atomic-absorption technique. The accuracy was checked by using data from instrumental neutron-activation analysis (INAA) and standard reference materials. An analogue integrator gave a better linearity and detection limit than conventional peak-reading.     

Determination of gold in tissue by carbon-furnace atomic-absorption spectrometry

A sensitive and reproducible technique is reported for the determination of gold in tissue by carbon-furnace atomic-absorption spectrometry. Results are compared with those obtained by using a flame-atomization procedure and by neutron-activation analysis. The method is used to analyse samples of kidney, liver, spleen, nails and hair from human subjects. A possible correlation between gold levels in nails and plasma is suggested.     

Optimization of microwave digestion for mercury determination in marine biological samples by cold vapour atomic absorption spectrometry

Optimization of acid digestion method for mercury determination in marine biological samples (dolphin liver, fish and mussel tissues) using a closed vessel microwave sample preparation is presented. Five digestion procedures with different acid mixtures were investigated: the best results were obtained when the microwave-assisted digestion was based on sample dissolution with HNO3-H2SO4-K2Cr2O7 mixture. A comparison between microwave digestion and conventional reflux digestion shows there are considerable losses of mercury in the open digestion system. The microwave digestion method has been tested satisfactorily using two certified reference materials. Analytical results show a good agreement with certified values. The microwave digestion proved to be a reliable and rapid method for decomposition of biological samples in mercury determination.