Electrochemical Determination of Hydrogen Peroxide Using a Glassy Carbon Electrode Modified with Three-Dimensional Copper Hydroxide Nanosupercages and Electrochemically Reduced Graphene Oxide

Three-dimensional copper hydroxide nanosupercages and electrochemically reduced graphene oxide were used to modify the glassy carbon electrode for the selective determination of hydrogen peroxide. The morphology and electrochemistry properties of copper hydroxide nanosupercage/electrochemically reduced graphene oxide/glassy carbon electrode were characterized using transmission electron microscopy, scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectra, Raman spectra, cyclic voltammetry, and electrochemical impedance spectroscopy. The resulting copper hydroxide nanosupercage/electrochemically reduced graphene oxide/glassy carbon electrode showed favorable performance for the electrocatalytic reduction of hydrogen peroxide. The amperometric current–time curve of the electrochemical sensor exhibited a wide linear range from 0.5 to 1030?µM with a limit of detection of 0.23?µM at a signal-to-noise ratio of three. Moreover, the sensor provided favorable selectivity, reproducibility, and stability and was used for the determination of H₂O₂ in tap water.     

Electrochemical Determination of Dopamine Using a Graphene–Screen-Printed Carbon Electrode with Magnetic Solid-Phase Microextraction

A magnetically separable Fe₃O₄@Diaion HP-2MG composite was prepared using the coprecipitation method and the resulting magnetic Fe₃O₄@Diaion HP-2MG composites were used for the separation and preconcentration of trace amounts of dopamine. For the detection stage, square wave voltammetry on a disposable graphene–screen-printed carbon electrode was successfully used for the determination of dopamine. The graphene–screen-printed carbon electrode exhibited excellent electroanalytical performance for dopamine. The linear concentration range was from 0.8 to 80?µM and a detection limit of 50?nM for dopamine was obtained. In combination with the magnetic solid-phase extraction method, the sensor response was linearly proportional to the concentration of dopamine in the range of 0.01–6.0?µM with a correlation coefficient of approximately 0.9992. The detection limit of the sensor was found to be 5.0?nM by square wave voltammetry. The combined methodology was successfully applied to determine dopamine in urine samples with good recoveries ranging from 95 to 98%.     

Fabrication of Hemoglobin/Ionic Liquid Modified Carbon Paste Electrode Based on the Electrodeposition of Gold Nanoparticles/CdS Quantum Dots and Its Electrochemical Application

A novel H₂O₂ amperometric biosensor based on the electrodeposition of gold nanoparticles (AuNPs) and CdS quantum dots (CdS QDs) onto a carbon paste electrode (CPE) and immobilizing hemoglobin (Hb) with ionic liquid (IL), is presented in this article. The modification process of the electrode was monitored by scanning electron microscopy (SEM), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Due to synergistic effects of AuNPs, CdS QDs and IL, the biosensor exhibited high stability and good bioelectrocatalytic ability to H₂O₂ with a linear concentration range from 10 to 750 µM and a detection limit of 4.35 µM (S/N=3).     

Direct electrochemical behavior of hemoglobin at surface of Au@Fe3O4 magnetic nanoparticles

Nanoparticles (NPs) consisting of an Fe₃O₄ core and a thin gold shell (referred to as Au@Fe₃O₄ NPs) were self-assembled on the surface of a glassy carbon electrode modified with ethylenediamine. Following adsorption of hemoglobin, its interaction with the NPs was studied by UV–Vis spectroscopy, electrochemical impedance spectroscopy, and cyclic voltammetry. Stable and well-defined redox peaks were observed at about ?350 mV and ?130 mV in pH 6.0 buffer. The modified electrode was used as a mediator-free sensor for hydrogen peroxide (H₂O₂), with a linear range from 3.4 µM to 4.0 mM of H₂O₂, and with a 0.67 µM detection limit (at an S/N of 3). The apparent Michaelis-Menten constant is 2.3 mM.     

Electrodeposition of PdAu Alloy Nanoparticles on Ionic Liquid Functionalized Graphene Film for the Voltammetric Determination of Oxalic Acid

An ionic liquid functionalized graphene film was prepared and PdAu nanoparticles (NPs) were electrodeposited on it. The PdAu NPs were characterized by various methods and they showed the features of alloys. In 0.2 M H₂SO₄ solution, oxalic acid (OA) exhibited a sensitive anodic peak at the resulting electrode at about 1.1 V (vs. SCE), and the peak current was linear to OA concentration in the range of 5–100 µM with a sensitivity of 45.5 µA/mM. The detection limit was 2.7 µM (S/N=3). The electrode was successfully applied to the determination of OA in real sample.     

A New Electrochemical Biosensor for Determination of Hydrogen Peroxide in Food Based on Well‐Dispersive Gold Nanoparticles on Graphene Oxide

Herein, we describe a new method for the detection of hydrogen peroxide (H₂O₂) in food by using an electrochemical biosensor. Initially, ultrafine gold nanoparticles dispersed on graphene oxide (AuNP‐GO) were synthesized by the redox reaction between AuCl₄^? and GO, and thionine‐catalase conjugates were then assembled onto the AuNP‐GO surface on a glassy carbon electrode. With the aid of the AuNP‐GO, the as‐prepared biosensor exhibited good electrocatalytic efficiency toward the reduction of H₂O₂ in pH 5.8 acetic acid buffer. Under optimal conditions, the dynamic responses of the biosensor toward H₂O₂ were achieved in the range from 0.1 µM to 2.3 mM, and the detection limit (LOD) was 0.01 µM at 3s_B. The Michaelis–Menten constant was measured to be 0.98 mM. In addition, the repeatability, reproducibility, selectivity and stability of the biosensor were investigated and evaluated in detail. Finally, the method was applied for sensing H₂O₂ in spiked or naturally contaminated samples including sterilized milk, apple juices, watermelon juice, coconut milk, and mango juice, receiving good correspondence with the results from the permanganate titration method. The disposable biosensor could offer a great potential for rapid, cost‐effective and on‐field analysis of H₂O₂ in foodstuff.     

A Third‐Generation Hydrogen Peroxide Biosensor Based on Horseradish Peroxidase Immobilized in Carbon Nanotubes/ SBA‐15 Film

A new third‐generation biosensor for H₂O₂ assay was developed on the basis of the immobilization of horseradish peroxidase (HRP) in a nanocomposite film of carbon nanotubes (CNTs)‐SBA‐15 modified gold electrode. The biological activity of HRP immobilizing in the composite film was characterized by UV‐vis spectra. The HRP immobilized in the nanocomposite matrix displayed excellent electrocatalytic activity to the reduction of H₂O₂. The effects of the experimental variables such as solution pH and working potential were investigated using steady‐state amperometry. Under the optimal conditions, the resulting biosensor showed a linear range from 1 µM to 7 mM and a detection limit of 0.5 µM (S/N=3). Moreover, the stability and reproducibility of this biosensor were evaluated with satisfactory results.     

Graphene–Pt nanocomposite for nonenzymatic detection of hydrogen peroxide with enhanced sensitivity

A sensitive hydrogen peroxide (H₂O₂) sensor was fabricated based on graphene–Pt (GN–Pt) nanocomposite. The GN–Pt was synthesized by photochemical reduction of K₂PtCl₄ on GNs, and characterized by atomic force microscope (AFM), transmission electron microscope (TEM), and energy-dispersive X-ray spectroscopy (EDS). Electrochemical investigations indicated that the GN–Pt exhibited a high peak current and low overpotential towards the reduction of H₂O₂. The GN–Pt modified glass carbon electrode displayed a wide linear range (2–710 μM), low limit of detection (0.5 μM) and good selectivity for detection of H₂O₂ with a much higher sensitivity than that of Pt nanoparticles or graphene modified electrode.     

Development of Silver Nanowires Based Highly Sensitive Amperometric Glucose Biosensor

The fabrication of a highly sensitive amperometric glucose biosensor based on silver nanowires (AgNWs) is presented. The electrochemical behavior of glassy carbon electrode modified by Ag NWs exhibits remarkable catalytic performance towards hydrogen peroxide (H₂O₂) and glucose detection. The biosensor could detect glucose in the linear range from 0.005 mM to 10 mM, with a detection limit of 50 µM (S/N=3). The glucose biosensor shows high and reproducible sensitivity of 175.49 µA cm^?2 mM and good stability. In addition, the biosensor exhibits a good anti‐interference ability and favorable stability over relatively long‐term storage (more than 21 days).     

Reduced Graphene Oxide|Carbon Ceramic Electrode Modified with CdS‐Hemoglobin as a Sensitive Hydrogen Peroxide Biosensor

A sensitive hydrogen peroxide (H₂O₂) biosensor was developed based on a reduced graphene oxide|carbon ceramic electrode (RGO|CCE) modified with cadmium sulfide‐hemoglobin (CdS‐Hb). The electron transfer kinetics of Hb were promoted due to the synergetic function of RGO and CdS nanoparticles. The transfer coefficient (α) and the heterogeneous electron transfer rate constant (k_s) were calculated to be 0.54 and 2.6 s^?1, respectively, indicating a great facilitation achieved in the electron transfer between Hb and the electrode surface. The biosensor showed a good linear response to the reduction of H₂O₂ over the concentration range of 2–240 µM with a detection limit of 0.24 µM (S/N=3) and a sensitivity of 1.056 µA µM^?1 cm^?2. The high surface coverage of the CdS‐Hb modified RGO|CCE (1.04×10^?8 mol cm^?2) and a smaller value of the apparent Michaelis? Menten constant (0.24 mM) confirmed excellent loading of Hb and high affinity of the biosensor for hydrogen peroxide.     

Self-assembly of ultra-small gold nanoparticles on an indium tin oxide electrode for the enzyme-free detection of hydrogen peroxide

A novel enzyme-free electrochemical sensor for H₂O₂ was fabricated by modifying an indium tin oxide (ITO) support with (3-aminopropyl) trimethoxysilane to yield an interface for the assembly of colloidal gold. Gold nanoparticles (AuNPs) were then immobilized on the substrate via self-assembly. Atomic force microscopy showed the presence of a monolayer of well-dispersed AuNPs with an average size of ~4 nm. The electrochemical behavior of the resultant AuNP/ITO-modified electrode and its response to hydrogen peroxide were studied by cyclic voltammetry. This non-enzymatic and mediator-free electrode exhibits a linear response in the range from 3.0?×?10^?5 M to 1.0?×?10^?3 M (M?=?mol?·?L^?1) with a correlation coefficient of 0.999. The limit of detection is as low as 10 nM (for S/N?=?3). The sensor is stable, gives well reproducible results, and is deemed to represent a promising tool for electrochemical sensing.

Sensitive Electrochemical Determination of Hydrogen Peroxide Using Copper Nanoparticles in a Polyaniline Film on a Glassy Carbon Electrode

Rapid and accurate determination of hydrogen peroxide is necessary in biochemistry and environmental science. In this paper, a sensitive hydrogen peroxide electrochemical sensor was developed by cyclic voltammetry deposition of polyaniline–copper nanocomposite film on a glassy carbon electrode. The synthesized polyaniline/Cu composites were characterized by scanning electron microscopy and X-ray diffraction. With a typical working potential of 0.4?V (versus Ag/AgCl) and a pH value of 6.0, the prepared electrochemical sensor achieved linear range of 1.0–500?µM for hydrogen peroxide detection. A relative standard deviation of 4.9% for n?=?7 and 10.0?µM of H₂O₂ and a limit of detection of 0.33?µM at a signal-to-noise ratio?=?3 were observed. The sensor was successfully used for the analysis of tap water, and a spiked recovery of 93.0?±?2.1% was obtained, further confirming the sensor’s accuracy and feasibility.     

Application of spinel-structured MgFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles for simultaneous electrochemical determination diclofenac and morphine

The paper describes a sensitive method for simultaneous sensing of morphine (MOR) and diclofenac (DCF). The surface of a MgFe₂O₄/graphite paste electrode was modified with multi-walled carbon nanotubes, and the resulting sensor was characterized by cyclic voltammetry, differential pulse voltammetry, chronoamperometry, and electrochemical impedance spectroscopy. The electrode showed an efficient synergistic effect in term of oxidation of DCF and MOR, with sharp oxidation peaks occurring at +0.370 and 0.540 V (vs Ag/AgCl) at pH 7.0. The calibration plot for MOR is linear in the 50 nM to 920 μM concentration range, and the detection limit is 10 nM (at a signal-to-noise ratio of 3). The respective data for DCF are 100 nM to 580 μM, with a 60 nM LOD. The sensor was applied to the determination of MOR and DCF in spiked serum and urine samples, with recoveries ranging between 91.4 and 100.7 %.

Open image in new window

Graphical abstract A sensitive method for simultaneous sensing of morphine (MOR) and diclofenac (DCF) is described. The surface of MgFe₂O₄/graphite paste electrode was modified with multi-walled carbon nanotubes, and the resulting sensor showed an efficient synergistic effect in terms of oxidation of DCF and MOR. The calibration plot for MOR is linear in the 50 nM to 920 μM concentration range, and the detection limit is 10 nM. The respective data for DCF are 100 nM to 580 μM, with a 60 nM LOD.

     

A Novel Enzymatic Glucose Biosensor and Nonenzymatic Hydrogen Peroxide Sensor Based on (3‐Aminopropyl) Triethoxysilane Functionalized Reduced Graphene Oxide

In the present study, a novel enzymatic glucose biosensor using glucose oxidase (GOx) immobilized into (3‐aminopropyl) triethoxysilane (APTES) functionalized reduced graphene oxide (rGO‐APTES) and hydrogen peroxide sensor based on rGO‐APTES modified glassy carbon (GC) electrode were fabricated. Nafion (Nf) was used as a protective membrane. For the characterization of the composites, Fourier transform infrared spectroscopy (FTIR), X‐ray powder diffractometer (XRD), and transmission electron microscopy (TEM) were used. The electrochemical properties of the modified electrodes were investigated using electrochemical impedance spectroscopy, cyclic voltammetry, and amperometry. The resulting Nf/rGO‐APTES/GOx/GC and Nf/rGO‐APTES/GC composites showed good electrocatalytical activity toward glucose and H₂O₂, respectively. The Nf/rGO‐APTES/GC electrode exhibited a linear range of H₂O₂ concentration from 0.05 to 15.25 mM with a detection limit (LOD) of 0.017 mM and sensitivity of 124.87 μA mM⁻¹ cm⁻². The Nf/rGO‐APTES/GOx/GC electrode showed a linear range of glucose from 0.02 to 4.340 mM with a LOD of 9 μM and sensitivity of 75.26 μA mM⁻¹ cm⁻². Also, the sensor and biosensor had notable selectivity, repeatability, reproducibility, and storage stability.     

Hemin Functionalized Multiwalled Carbon Nanotubes as a Matrix for Sensitive Electrogenerated Chemiluminescence Cholesterol Biosensor

Based on hemin‐MWCNTs nanocomposite and hemin‐catalyzed luminol‐H₂O₂ reaction, a sensitive electrogenerated chemiluminescence (ECL) cholesterol biosensor was proposed in this paper. Firstly, hemin‐MWCNTs was prepared via π–π stacking and modified on the surface of GCE. Subsequently, cholesterol oxidase (ChOx) was adsorbed on the modified electrode to achieve a cholesterol biosensor. Hemin‐MWCNTs nanocomposite provided the electrode with a large surface area to load ChOx, and endowed the nanostructured interface on the electrode surface to enhance the performance of biosensor. The biosensor responded to cholesterol in the linear range from 0.3 µM to 1.2 mM with a detection limit of 0.1 µM (S/N=3).     

Direct Electrochemistry of Hemoglobin Immobilized on Carbon‐Coated Iron Nanoparticles for Amperometric Detection of Hydrogen Peroxide

A novel method for preparation of hydrogen peroxide biosensor was presented based on immobilization of hemoglobin (Hb) on carbon‐coated iron nanoparticles (CIN). CIN was firstly dispersed in a chitosan solution and cast onto a glassy carbon electrode to form a CIN/chitosan composite film modified electrode. Hb was then immobilized onto the composite film with the cross‐linking of glutaraldehyde. The immobilized Hb displayed a pair of stable and quasireversible redox peaks and excellent electrocatalytic reduction of hydrogen peroxide (H₂O₂), which leading to an unmediated biosensor for H₂O₂. The electrocatalytic response exhibited a linear dependence on H₂O₂ concentration in a wide range from 3.1 μM to 4.0 mM with a detection limit of 1.2 μM (S/N=3). The designed biosensor exhibited acceptable stability, long‐term life and good reproducibility.     

Amperometric Biosensors Based on Platinum Nanowires

Abstract

Platinum nanowires (PtNW) were prepared by an electrodeposition strategy using nanopore alumina template. The nanowires prepared were dispersed in chitosan (CHIT) solution and stably immobilized onto the surface of glassy carbon electrode (GCE). The electrochemical behavior of PtNW‐modified electrode and its application to the electrocatalytic reduction of hydrogen peroxide (H₂O₂) are investigated. The modified electrode allows low potential detection of hydrogen peroxide with high sensitivity and fast response time. As an application example, the glucose oxidase was immobilized onto the surface of PtNW‐modified electrode through cross‐linking by glutaric dialdehyde. The detection of glucose was performed in phosphate buffer at –0.2 V. The resulting glucose biosensor exhibited a short response time (<8 s), with a linear range of 10^?5?10^?2 M and detection limit of 5×10^?6 M.     

Electrochemical Peroxidase‐Catalase Clark‐Type Biosensor: Computed and Experimental Response

A bioelectrode containing immobilized catalase and peroxidase was built using a Clark‐type oxygen electrode. The bioelectrode responded to hydrogen peroxide (H₂O₂) as well as to acetaminophen (Ac). The sensitivity of the bioelectrode for H₂O₂ was 0.35 mM O₂/mM H₂O₂ and for Ac it was 0.23–1.05 µM O₂/µM Ac at pH 6.6 and 25 °C. The limit of detection of Ac varied from 12 to 44 µM. The half‐time of the bioelectrode response to hydrogen peroxide was 36 s. The modeling of the bioelectrode action was performed digitally at transition and steady‐state conditions using finite difference technique. The calculated half‐time of the bioelectrode response to hydrogen peroxide was 53 % larger and the steady‐state response 11 % less than experimentally determined. The response to Ac was 2–3 times smaller in comparison to the experimental values. The calculated response change correlated with the experimentally determined when the catalase and peroxidase concentrations in the biocatalytical membrane changed 3–4 orders of magnitude. The simulations of the bioelectrode response revealed that the bioelectrode acts in diffusion limiting conditions at almost all enzymes concentrations. The model appears to be promising for optimization of the bioelectrode response.     

Sensitive and Rapid Flow Injection Amperometric Hydrazine Sensor using an Electrodeposited Gold Nanoparticle Graphite Pencil Electrode

A gold (Au) nanoparticle-modified graphite pencil electrode was prepared by an electrodeposition procedure for the sensitive and rapid flow injection amperometric determination of hydrazine (N₂H₄). The electrodeposited Au nanoparticles on the pretreated graphite pencil electrode surface were characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction spectroscopy, and electrochemical impedance spectroscopy. Cyclic voltammograms showed that the Au nanoparticle-modified pretreated graphite pencil electrode exhibits excellent electrocatalytic activity toward oxidation of hydrazine because the highly irreversibly and broadly observed oxidation peak at +600?mV at the pretreated graphite pencil electrode shifted to ?167?mV at the Au nanoparticle pretreated graphite pencil electrode; in addition, a significant enhancement in the oxidation peak current was obtained. Thus, the flow-injection (FI) amperometric hydrazine sensor was constructed based on its electrocatalytic oxidation at the Au nanoparticle-modified pretreated graphite pencil electrode. The Au nanoparticle-modified pretreated graphite pencil electrode exhibits a linear calibration curve between the flow injection amperometric current and hydrazine concentration within the concentration range from 0.01 to 100?µM with a detection limit of 0.002?µM. The flow injection amperometric sensor has been successfully used for the determination of N₂H₄ in water samples with good accuracy and precision.     

Carbon nanofibers decorated with platinum nanoparticles: a novel three-dimensional platform for non-enzymatic sensing of hydrogen peroxide

We have developed a 3-dimensional (3-D) electrochemical sensor for highly sensitive detection of hydrogen peroxide (H₂O₂). Porous 3-D carbon nanofibers (CNFs), prepared by electrospinning, served as scaffold on a glassy carbon electrode. The 3-D CNFs were functionalized with platinum nanoparticles (Pt-NPs) by in-situ gas-phase decomposition of platinum salts at high temperature. The Pt-NPs act as an electrocatalyst for the decomposition of H₂O₂. TEM revealed that large amounts of Pt-NPs are deposited in the electrospun CNFs electrode even without using any stabilizer or reducing reagent. The sensor was investigated by cyclic voltammetry and amperometry and displays a good response to H₂O₂ with a linear range between 10 μM and 15 mM (R?=?0.9994), a low detection limit (3.4 μM at a signal-to-noise ratio of 3), and a response time of 3 s. The sensor shows excellent stability and selectivity.