Treatment of TiO2 with COOH‐Functionalized Germanium Nanoparticles to Enhance the Photocurrent of Dye‐Sensitized Solar Cells

A dye‐sensitized solar cell (DSSC) containing a TiO₂ film treated with COOH‐functionalized germanium nanoparticles (Ge COOH Nps) exhibited a higher short‐circuit photocurrent density (J_sc; 15.4 mA cm⁻²) compared to the corresponding untreated DSSC (13.4 mA cm⁻²) using N719 and a 12 μm thick TiO₂ film at 100 mW cm⁻². The amount of N719 attached to the treated TiO₂ film was 21 % greater than that attached to the untreated TiO₂ film. Enhancement of the J_sc value by 15 % was attributed mostly to an intramolecular charge transfer from N719 attached to the Ge COOH Nps to the TiO₂ conduction band through the Ge COOH Nps.     

Sonochemical Preparation of Hierarchical ZnO Hollow Spheres for Efficient Dye‐Sensitized Solar Cells

Hierarchical ZnO hollow spheres (400–500 nm in diameter) consisting of ZnO nanoparticles with a diameter of approximately 15 nm have been successfully prepared by a facile and rapid sonochemical process. The formation of hierarchical ZnO hollow spheres is attributed to the oriented attachment and subsequent Ostwald ripening process according to time‐dependent experiments. The as‐prepared ZnO hollow spheres are used as a photoanode in dye‐sensitized solar cells and exhibit a highly efficient power conversion efficiency of 4.33 %, with a short‐circuit current density of 9.56 mA cm^?2, an open‐circuit voltage of 730 mV, and a fill factor of 0.62 under AM 1.5 G one sun (100 mW cm^?2) illumination. Moreover, the photovoltaic performance (4.33 %) using the hierarchical ZnO hollow spheres is 38.8 % better than that of a ZnO nanoparticle photoelectrode (3.12 %), which is mainly attributed to the efficient light scattering for the former.     

Ultrafast Photodynamics of the Indoline Dye D149 Adsorbed to Porous ZnO in Dye‐Sensitized Solar Cells

We investigate the ultrafast dynamics of the photoinduced electron transfer between surface‐adsorbed indoline D149 dye and porous ZnO as used in the working electrodes of dye‐sensitized solar cells. Transient absorption spectroscopy was conducted on the dye in solution, on solid state samples and for the latter in contact to a I^?/I₃^? redox electrolyte typical for dye‐sensitized solar cells to elucidate the effect of each component in the observed dynamics. D149 in a solution of 1:1 acetonitrile and tert‐butyl alcohol shows excited‐state lifetimes of 300±50 ps. This signature is severely quenched when D149 is adsorbed to ZnO, with the fastest component of the decay trace measured at 150±20 fs due to the charge‐transfer mechanism. Absorption bands of the oxidized dye molecule were investigated to determine regeneration times which are in excess of 1 ns. The addition of the redox electrolyte to the system results in faster regeneration times, of the order of 1 ns.     

Structural Control of Hierarchically‐Ordered TiO2 Films by Water for Dye‐Sensitized Solar Cells

A facile way of controlling the structure of TiO₂ by changing the amount of water to improve the efficiency of dye‐sensitized solar cells (DSSCs) is reported. Hierarchically ordered TiO₂ films with high porosity and good interconnectivity are synthesized in a well‐defined morphological confinement arising from a one‐step self‐assembly of preformed TiO₂ (pre‐TiO₂) nanocrystals and a graft copolymer, namely poly(vinyl chloride)‐g‐poly(oxyethylene methacrylate). The polymer–solvent interactions in solution, which are tuned by the amount of water, are shown to be a decisive factor in determining TiO₂ morphology and device performance. Systematic control of wall and pore size is achieved and enables the bifunctionality of excellent light scattering properties and easy electron transport through the film. These properties are characterized by reflectance spectroscopy, incident photon‐to‐electron conversion efficiency, and electrochemical impedance spectroscopy analyses. The TiO₂ photoanode that is prepared with a higher water ratio, [pre‐TiO₂]:[H₂O]=1:0.3, shows a larger surface area, greater light scattering, and better electron transport, which result in a high efficiency (7.7 %) DSSC with a solid polymerized ionic liquid. This efficiency is much greater than that of commercially available TiO₂ paste (4.0 %).     

A Promising Candidate with D‐A‐A‐A Architecture as an Efficient Sensitizer for Dye‐Sensitized Solar Cells

A series of metal‐free organic dyes with electron‐rich (D) and electron‐deficient units (A) as π linkers have been studied theoretically by means of density functional theory (DFT) and time‐dependent DFT calculations to explore the effects of π spacers on the optical and electronic properties of triphenylamine dyes. The results show that Dye 1 with a structure of D‐A‐A‐A is superior to the typical C218 dye in various key aspects, including the maximum absorption (λ_max=511 nm), the charge‐transfer characteristics (D/Δq/t is 5.49 Å/0.818 e^?/4.41 Å), the driving force for charge‐carrier injection (ΔG_inject=1.35 eV)/dye regeneration (ΔG_regen=0.27 eV), and the lifetime of the first excited state (τ=3.1 ns). It is thus proposed to be a promising candidate in dye‐sensitized solar cell applications.     

Peripherally and Axially Carboxylic Acid Substituted Subphthalocyanines for Dye‐Sensitized Solar Cells

A series of subphthalocyanines (SubPcs) bearing a carboxylic acid group either at the peripheral or axial position have been designed and synthesized to investigate the influence of the COOH group positions on the dye‐sensitized solar cell (DSSC) performance. The DSSC devices based on SubPcs with axially substituted carboxylic acid groups showed low photovoltaic performance, whereas peripherally substituted one exhibited higher power conversion efficiency owing to improved injection from LUMO of SubPcs to the TiO₂ conduction band.     

The Influence of Charge Transport and Recombination on the Performance of Dye‐Sensitized Solar Cells

Electrochemical impedance spectroscopy (EIS) and transient voltage decay measurements are applied to compare the performance of dye sensitized solar cells (DSCs) using organic electrolytes, ionic liquids and organic‐hole conductors as hole transport materials (HTM). Nano‐crystalline titania films sensitized by the same heteroleptic ruthenium complex NaRu(4‐carboxylic acid‐4′‐carboxylate) (4,4′‐dinonyl‐2,2′‐bipyridyl)(NCS)₂ , coded Z‐907Na are employed as working electrodes. The influence of the nature of the HTM on the photovoltaic figures of merit, that is, the open circuit voltage, short circuit photocurrent and fill factor is evaluated. In order to derive the electron lifetime, as well as the electron diffusion coefficient and charge collection efficiency, EIS measurements are performed in the dark and under illumination corresponding to realistic photovoltaic operating conditions of these mesoscopic solar cells. A theoretical model is established to interpret the frequency response off the impedance under open circuit conditions, which is conceptually similar to photovoltage transient decay measurements. Important information on factors that govern the dynamics of electron transport within the nanocrystalline TiO₂ film and charge recombination across the dye sensitized heterojunction is obtained.     

Thieno[3,4‐b]thiophene‐Based Organic Dyes for Dye‐Sensitized Solar Cells

New dipolar sensitizers containing an ethyl thieno[3,4‐b]thiophene‐2‐carboxylate (ETTC) entity in the conjugated spacer have been synthesized in two isomeric forms. These compounds were used as the sensitizers of n‐type dye‐sensitized solar cells (DSSCs). The best conversion efficiency (5.31 %) reaches approximately 70 % of the N719‐based (7.41 %) DSSC fabricated and measured under similar conditions. The ETTC‐containing compounds exhibit a bathochromic shift of the absorption compared to their thiophene congeners due to the quinoid effect, however, charge‐trapping at the ester group of ETTC was found to jeopardize the electron injection and lower the cell efficiency. Charge trapping is alleviated as the ester group of ETTC is replaced with a hydrogen atom, as evidenced from the theoretical computation.     

Adsorption of 4‐tert‐Butylpyridine on TiO2 Surface in Dye‐Sensitized Solar Cells

4‐tert‐Butylpyridine (4‐TBP) has been widely used as additive in dye‐sensitized solar cells (DSC), owing to its improvement of the fill factor and the open circuit voltage of DSC. In this paper, the adsorption of 4‐TBP on the rutile TiO₂(110) surface in DSC was studied by using the density functional theory at DFT/B3LYP level. By comparing the results with those attained from experiments, it was concluded that the 4‐TBP could chemiadsorb on the incompletely covered surface Ti atoms in the electrode. The probable mechanism of compressed recombination by coordinated 4‐TBP in DSC was proposed.     

Opp‐Dibenzoporphyrins as a Light‐Harvester for Dye‐Sensitized Solar Cells

New opp‐dibenzoporphyrins were prepared in a concise method that was based on a Pd⁰‐catalyzed cascade reaction. These porphyrins, which contained carboxylic‐acid linker groups on benzene rings that were fused to the porphyrin at their β,β′‐positions, were examined as sensitizers for dye‐sensitized solar cells for the first time. Whereas all of the porphyrins showed solar‐energy‐to‐electricity conversion, an opp‐dibenzoporphyrin with conjugated carboxylic‐acid linkers displayed the highest conversion efficiency and an exceptionally high J_sc value. Cyclic voltammetry of these porphyrins suggested that the fusion of two aromatic benzene rings onto the periphery of the porphyrin lowered the HOMO–LUMO energy gap; the incorporation of a conjugated carboxylic‐acid linker group decreased the HOMO–LUMO gap even further. These CV data are consistent with DFT calculations for these porphyrins and agree well with the UV/Vis absorption‐ and fluorescence spectra of these porphyrins.     

Platinum‐Free Binary Co‐Ni Alloy Counter Electrodes for Efficient Dye‐Sensitized Solar Cells

Dye‐sensitized solar cells (DSSCs) have attracted growing interest because of their application in renewable energy technologies in developing modern low‐carbon economies. However, the commercial application of DSSCs has been hindered by the high expenses of platinum (Pt) counter electrodes (CEs). Here we use Pt‐free binary Co‐Ni alloys synthesized by a mild hydrothermal strategy as CE materials in efficient DSSCs. As a result of the rapid charge transfer, good electrical conduction, and reasonable electrocatalysis, the power conversion efficiencies of Co‐Ni‐based DSSCs are higher than those of Pt‐only CEs, and the fabrication expense is markedly reduced. The DSSCs based on a CoNi_0.25 alloy CE displays an impressive power conversion efficiency of 8.39 %, fast start‐up, multiple start/stop cycling, and good stability under extended irradiation.