Characterization of Kaolin Glassy Carbon Modified Electrodes: Preconcentration of 2‐Chlorophenol

In this paper we describe the use of two kaolin‐type aluminosilicate clays, a commercial ceramic‐grade kaolin (K) and a natural kaolin from mines in Bolívar State Venezuela (K‐Ve), for the preparation of film‐based clay‐modified glassy carbon electrodes. We examine their behavior during the preconcentration and subsequent anodic oxidation of 2‐chlorophenol. Kaolin samples were used as raw materials and modified with cationic surfactant, cetyltrimethylammonium bromide (CTAB) or nonionic surfactant, octylphenoxypolyethoxyethanol (TX100). The electrode polishing was the key step to produce stable films. 2‐Chlorophenol electrooxidation is favored by the presence of the surfactants in the film. The X‐ray patterns show that the kaolin K‐Ve includes quartz as nonclay mineral, while the kaolin K showed only diffraction peaks characteristic of kaolinite phase. This may be why the TX100/K‐Ve/GC electrode adsorbs more 2‐CPh than the TX100/K/GC electrode. On the other hand, analysis of the limiting currents obtained from hydrodynamic techniques indicated that the permeability of TX100/kaolin films is greater than that of CTAB/kaolin films. The TX100/K‐Ve/GC electrode showed excellent stability. A linear response range from 0.01mgL^?1 up to 0.1 mg L^?1 with a detection limit of 0.0016 mg L^?1 was observed in the optimized conditions.     

Amperometric Detection of 4‐Chlorophenol on Two Types of Expanded Graphite Based Composite Electrodes

The assessment of an expanded graphite‐Ag‐zeolite‐epoxy composite (EG‐Z‐Ag‐Epoxy) electrode for the determination of 4‐chlorophenol (4‐CP) is described and compared to the corresponding expanded graphite‐epoxy composite (EG‐Epoxy) electrode. Cyclic voltammetry was used to characterize the electrochemical behavior and determination of 4‐CP at both electrodes in 0.1 M Na₂SO₄ and 0.1 M NaOH supporting electrolytes. A substantial enhancement of sensitivity for the determination of 4‐CP at the EG‐Z‐Ag‐Epoxy electrode was reached by applying a chemical preconcentration step prior to voltammetric quantification. Also, under these last conditions the lowest limit of detection of 1 μM illustrates the analytical versatility of this electrode in a concentration range where aquatic 4‐chlorophenol pollution is known to occur.     

Electrocatalytic Behavior and Amperometric Detection of Morphine on ITO Electrode Modified with Directly Electrodeposited Gold Nanoparticles

A gold nanoparticles (AuNPs) modified indium tin oxide (ITO) film coated glass electrode was prepared via a novel electrochemical deposition technique. The UV‐visible spectrum and SEM indicated that the AuNPs on ITO electrode surface were spherical shape and quite symmetric distributed. The modified electrode exhibited excellent catalytic activity for the oxidation of morphine (MO). At optimal experimental condition, the oxidation current was responsive with the MO concentrations ranging from 8.0×10^?7 to 1.6×10^?5 M, the detection limit was 2.1×10 ^–7 M. The modified electrode also exhibited high stability and reproducibility. The average recoveries of detection MO in human urine were ranged between 91.95% and 92.23%, and the RSD was less than 3.68% (n=5).     

Electrochemical Detection of Steroid Hormones Using a Nickel‐Modified Glassy Carbon Electrode

This paper demonstrates the development of an analytical method for detecting steroid hormones by coupling HPLC to electrochemical detection, using a nickel‐modified glassy carbon electrode. The method was evaluated in terms of sensitivity, linear dynamic range, limit of detection, and response stability. The developed method exhibited good figures of merit for the steroid hormones studied with no evidence of electrode fouling. As an example, the limit of detection (S/N=3) for E3 was 0.10 µM and the response precision (n=5) was 0.6 %. The application of the method for the analysis of a real river water sample is demonstrated.     

Fabrication and Electrochemical Behavior of Vanadium‐Substituted Keggin‐Type Polyoxometalates Multilayer Films on 4‐Aminobenzoic Acid Modified Glassy Carbon Electrodes

Two Vanadium‐substituted Keggin‐type polyoxometalates, K₃H₂[α‐SiVW₁₁O₄₀]?6H₂O (SiVW₁₁) and K₄H₂[γ(1, 2)‐SiV₂W₁₀O₄₀]?4H₂O (SiV₂W₁₀) were first successfully immobilized on 4‐aminobenzoic acid modified glass carbon electrodes respectively by layer‐by‐layer assembly with poly (ethylenimine) (PEI) as counterions. The regular growth processes were monitored by cyclic voltammetry (CV), and it was proved that the multilayer films were uniform and stable. The cyclic voltammetry results indicated that the electrochemical behavior of two multilayer films was similar, and their redox couples are pH‐ and scan rate‐dependent. The multilayer films show favorable electrocatalytic active toward the reduction of NO₂^?, IO₃^? and H₂O₂.     

Electrochemical Detection of 2‐Naphthol at a Glassy Carbon Electrode Modified with Tosflex Film

In this study, a Tosflex (a perfluoro‐anion‐exchange membrane) modified glassy carbon electrode has been used to detect 2‐naphthalenol (2‐naphthol) in aqueous solutions in order to demonstrate the electroanalytical application of Tosflex. 2‐naphthol polymerizes upon electrochemical oxidation at a glassy carbon electrode; however, the current related to this oxidation is too small for analytical purpose at low concentration level. A Tosflex polymer modified glassy carbon electrode (TFGCE) was found of having capability to improve the detection limit because 2‐naphthol molecules deprotonated in basic solutions to form 2‐naphtholate anions that were accumulated to TFGCE by the anion‐exchange characteristic of Tosflex. The accumulated 2‐naphtholate anions were determined with the following differential pulse voltammetry. With 3 minutes accumulation at +0.05 V, the dependence of oxidation current versus concentration was linear from 8×10^?7 M to 1×10^?5 M with a regression coefficient of 0.999 and a detection limit of 2×10^?7 M. Unlike many other anion‐exchange polymer modified electrodes, the TFGCE is stable at highly basic condition.     

Flow Injection Amperometric Detection at Enzyme‐Modified Gold Nanoelectrodes

Gold nanotubular electrode ensembles were prepared by using electroless deposition of the metal within the pores of polycarbonate particle track‐etched membranes. Glucose oxidase (Gox), used as a model enzyme, has been immobilized onto preformed self‐assembled monolayers (mercaptoethylamine or mercaptopropionic acid) on electroless gold via cross‐linking with glutaraldehyde or covalent attachment by carbodiimide coupling. Flow‐injection analysis systems in flow‐through or wall‐jet configurations using these Gox‐modified nanoelectrodes are described. The influence of different experimental parameters (i.e., applied potential, flow rate, interferents…?) on the analytical response of the sensor to glucose has been evaluated. Under optimized conditions, very reproducible results (standard deviations <4%, n=38) were obtained, linear calibration was achieved in the 2×10^?4 M to 3×10^?2 M concentration range and the detection limit was 2×10^?4 M. Moreover, no significant interferences from species like ascorbic and uric acids were observed at a potential of +0.9 V.     

Enhanced Sensitivity of 4‐Chlorophenol Detection by Use of Nitrobenzene as a Liquid Membrane over a Carbon Nanotube‐Modified Glassy Carbon Electrode

The analytical utility of nitrobenzene as a liquid membrane for the detection of hydrophobic compounds was examined with a glassy carbon electrode, using 4‐chlorophenol as the model analyte. Electrochemical experiments indicated a large partition coefficient for the entry of 4‐chlorophenol into the nitrobenzene (7.6×10²±1.5×10²). This was combined with an increase in effective electrode area by coating with single‐walled nanotubes. Differential pulse voltammetry produced a linear response across the range 0.3 nM to 1.5 nM with a sensitivity of 1.1×10^?5 A nM^?1 cm^?2. To the best of our knowledge, this limit of detection for phenol is lower than other nonenzymatic modifications of carbon.     

Preparation and Characterization of a Tin Pentacyanonitrosylferrate‐Modified Carbon Ceramic Electrode: Application to Electrocatalytic Oxidation and Amperometric Detection of L‐Cysteine

The sol‐gel technique was used to construct tin pentacyanonitrosylferrate (SnPCNF) modified composite carbon ceramic electrode (CCE). This involves two steps: construction of CCE containing metallic Sn powder and then electrochemical creating of SnPCNF on the surface of CCE. The SnPCNF modified CCE (SnPCNFlCCE) was characterized by energy‐dispersive X‐ray (EDX), FTIR and cyclic voltammetry (CV) techniques. The SnPCNF film showed electrocatalytic activity toward the oxidation of L ‐cysteine. A linear calibration plot was obtained over the L ‐cysteine concentration range 1–51 μM using chronoamperometry. L ‐cysteine was determined amperometrically at the surface of this modified electrode. The detection limit (for a signal to noise of 3) and sensitivity were found to be 0.62 μM and 126 μA/mM, respectively.     

Simultaneous Determination of 4‐Chlorophenol and Oxalic Acid Using an Expanded Graphite‐Epoxy Composite Electrode

An expanded graphite‐epoxy composite electrode (EG‐Epoxy) was employed for the simultaneous determination of 4‐chlorophenol (4‐CP) and oxalic acid (OA) by using cyclic voltammetry (CV), chronoamperometry (CA), and differential pulse voltammetry (DPV). The results indicated that OA could be determined in the presence of the same concentrations of 4‐CP within the concentration range of 0.1 mM to 0.5 mM with a relative standard deviation (RSD) smaller than 5%. Electrode fouling occurred during CA for 4‐CP concentrations larger than 0.5 mM. The DPV method was used for the simultaneous determination of 4‐CP and OA before and after electrochemical oxidation by chronopotentiometry under galvanostatic conditions (j=0.04 mA cm^?2, t=2 h) of a tap water sample spiked with 0.19 mM 4‐CP and 0.1 M Na₂SO₄.     

Pyrolyzed Photoresist Carbon Electrodes for Microchip Electrophoresis with Dual‐Electrode Amperometric Detection

The fabrication and evaluation of pyrolyzed photoresist films (PPF) for microchip capillary electrophoresis (CE) with dual‐electrode electrochemical (EC) detection is described. The sensitivity, linearity, and reproducibility were evaluated using catecholamines and related compounds, including dopamine (DA), 5‐hydroxyindole‐3‐acetic acid (5‐HIAA), ascorbic acid (AA), and catechol. Initial studies with DA show the response of the PPF electrodes to be linear between 25 and 500 μM (r²=0.999) with a limit of detection (LOD) of 5 μM (S/N=3) and sensitivity of 5.8 pA/μM. Selectivity was further enhanced by employing dual‐electrode detection in the series configuration for detection of species exhibiting chemically reversible redox reactions.     

Electrochemical Behaviors of Adenosine‐5′‐triphosphate on Molecular Wire Modified Carbon Paste Electrode and Its Sensitive Detection

A new electrochemical method was proposed for the determination of adenosine‐5′‐triphosphate (ATP) based on the electrooxidation at a molecular wire (MW) modified carbon paste electrode (CPE), which was fabricated with diphenylacetylene (DPA) as the binder. A single well‐defined irreversible oxidation peak of ATP appeared on MW‐CPE with adsorption‐controlled process and enhanced electrochemical response in a pH 3.0 Britton‐Robinson buffer solution, which was due to the presence of high conductive DPA in the electrode. The electrochemical parameters of ATP were calculated with the electron transfer coefficient (α) as 0.54, the electron transfer number (n) as 1.9, the apparent heterogeneous electron transfer rate constant (k_s) as 2.67 × 10^?5 s^?1 and the surface coverage (Γ_T) as 4.15 × 10^?10 mol cm^?2. Under the selected conditions the oxidation peak current was proportional to ATP concentration in the range from 1.0 × 10^?7 mol L^?1 to 2.0 × 10^?3 mol L^?1 with the detection limit as 1.28 × 10^?8 mol L^?1 (3σ) by sensitive differential pulse voltammetry. The proposed method showed good selectivity without the interferences of coexisting substances and was successful applied to the ATP injection samples detection.     

Solar Photocatalytic Degradation of 4‐Chlorophenol in Kaolinite Catalysts

This research applies semiconductor photocatalysts, which are formed by metal ion exchange on the surface of kaolinite catalyst with cations, to the study of photocatalytic degradation of 4‐chlorophenol. The analysis results of catalyst properties shows that, after sintering at 400 °C, kaolinite catalyst has a particle size of between 10–100 nm indicating the nano level of synthesized catalysts. Under the same condition, kaolinite‐Ag/Zn catalyst works better in degradation efficiency than single kaolinite‐Ag and kaolinite‐Zn catalysts. Kaolinite‐Zn catalyst declines in degradation efficacy after 150 minutes and performs poorer than the other three types of kaolinite catalysts. In the experiments of different amounts of catalysts, when the concentration exceeds 0.1 wt%, utilization of light energy and degradation efficiency will be reduced due to shielding effect. When at different pH values, the higher the pH value, the more OH‐will be released and that is beneficial for reaction with substances and the increase of reaction rate. Finally multivariate analysis proves that there is one determining factor that influences the photocatalytic degradation of 4‐chlorophenol in kaolinite catalysts, named as “the factor with intermediates competition degree,” the one affecting the 4‐CP degradation at different weight percentages that is referred to as the “shielding effect factor.”     

Electrochemical Behavior and Determination of L‐Tyrosine at Single‐walled Carbon Nanotubes Modified Glassy Carbon Electrode

Based on single‐walled carbon nanotubes (SWCNTs) modified glassy carbon electrode (GCE/SWCNTs), a novel method was presented for the determination of L ‐tyrosine. The GCE/SWCNTs exhibited remarkable catalytic and enhanced effects on the oxidation of L ‐tyrosine. In 0.10 mol/L citric acid‐sodium citrate buffer solution, the oxidation potential of L ‐tyrosine shifted negatively from +1.23 V at bare GCE to +0.76 V at GCE/SWCNTs. Under the optimized experimental conditions, the linear range of the modified electrode to the concentration of L ‐tyrosine was 5.0×10^?6–2.0×10^?5 mol/L (R₁=0.9952) and 2.7×10^?5–2.6×10^?4 mol/L (R₂=0.9998) with a detection limit of 9.3×10^?8 mol/L. The kinetic parameters such as α (charge transfer coefficient) and D (diffusion coefficient) were evaluated to be 0.66, 9.82×10^?5 cm² s^?1, respectively. And the electrochemical mechanism of L ‐tyrosine was also discussed.     

4‐Phosphatephenyl Covalently Modified Glassy Carbon Electrode for Real‐Time Electrochemical Monitoring of Paracetamol Release from Electrospun Nanofibers

A glassy carbon electrode (GCE) was covalently modified by 4‐phosphatephenyl (4‐PP). Sensing paracetamol (PCT) via linear sweep voltammetry in sulfuric buffer solution of pH 1.02 at 36.8 °C, the 4‐PP‐modified GCE showed high electrochemical sensitivity and long reusability. PCT‐loaded poly(vinyl alcohol) (PVA) nanofibers were prepared by electrospinning. Based on the calibration curve of PCT on the 4‐PP‐modified GCE, the PCT release process from the nanofibers was electrochemically monitored in real time via two routes. The results showed that the covalently modified GCE can be repeatedly used as real‐time electrochemical monitoring platform for drug release from drug‐loaded nanofibers in the long term.     

Glucose Biosensor Based on Multi‐Walled Carbon Nanotube Modified Glassy Carbon Electrode

An amperometric glucose biosensor based on multi‐walled carbon nanotube (MWCNT) modified glassy carbon electrode has been developed. MWCNT‐modified glassy carbon electrode was obtained by casting the electrode surface with multi‐walled carbon nanotube materials. Glucose oxidase was co‐immobilized on the MWCNT‐modified glassy carbon surface by electrochemical deposition of poly(o‐phenylenediamine) film. Enhanced catalytic electroreduction behavior of oxygen at MWCNT‐modified electrode surface was observed at a potential of ?0.40 V (vs. Ag|AgCl) in neutral medium. The steady‐state amperometric response to glucose was determined at a selected potential of ?0.30 V by means of the reduction of dissolved oxygen consumed by the enzymatic reaction. Common interferents such as ascorbic acid, 4‐acetamidophenol, and uric acid did not interfere in the glucose determination. The linear range for glucose determination extended to 2.0 mM and the detection limit was estimated to be about 0.03 mM.     

Voltammetric Reduction of a 4‐Nitroimidazole Derivative on a Multiwalled Carbon Nanotubes Modified Glassy Carbon Electrode

We report the electrochemical behavior of a 4‐nitroimidazole derivative, 1‐methyl‐4‐nitro‐2‐hydroxymethylimidazole (4‐NImMeOH), on glassy carbon electrode (GCE) modified with multiwalled carbon nanotubes (MWCNT). As dispersing agents, dimethylformamide (DMF) and water were used. The electrochemical response of the resulting electrodes was evaluated using linear sweep, cyclic and square‐wave voltammetry (LSV, CV and SWV). Several parameters such as medium pH, nature and concentration of the CNTs dispersion and accumulation time were tested. The optimal conditions determined for obtain better response were: pH 2, dispersion concentration=4 mg/mL of CNT in water, accumulation time=7 min. The MWCNT‐modified GCE exhibited attractive electrochemical properties producing enhanced currents with a significant reduction in the overpotential and good signal‐to‐noise characteristics, in comparison with the bare GCE. The modified electrode is highly repeatable for consecutive measurements, reaching a variation coefficient of 2.9% for ten consecutive runs.     

A Simple and Sensitive Method for the Amperometric Detection of Trace Chromium(VI) Based on Prussian Blue Modified Glassy Carbon Electrode

A simple and sensitive method for the amperometric detection of trace amount of chromium(VI) using a Prussian blue modified glassy carbon electrode (PB/GCE) is described here. The Everitts salt/Prussian blue redox couple of the PB film was found to mediate the Cr(VI) reduction, and the mechanism of electrochemical reaction was investigated. The effects of PB film thickness, applied potential and electrolyte solution on the current response of Cr(VI) reduction were thoroughly studied. Under the optimized conditions, the PB/GCE provided a wide linear range for Cr(VI) analysis from 0.5 to 200 ppb with excellent sensitivity (15±0.2 nA/ppb) and low detection limit (0.15 ppb). In addition, the modified electrode showed excellent stability, reproducibility and good resistance to other metal ions and surfactants. Finally, the proposed method was applied to detect trace Cr(VI) in wastewater with satisfactory results. The great advantages of the method were characterized by the simplicity, ease of preparation, stability, short analysis time and cost‐efficiency.     

Pulsed Amperometric Detection of Histamine at Glassy Carbon Electrodes Modified with Gold Nanoparticles

Gold nanocrystal‐modified glassy carbon electrodes (nAu‐GCE) were prepared and used for the determination of histamine by flow injection and high performance liquid chromatography using pulsed amperometric detection (PAD) as the detection mode. Experimental variables involved in the electrodeposition process of gold from a HAuCl₄ solution were optimized. A catalytic enhancement of the histamine voltammetric response was observed at the nAu‐GCE when compared with that obtained at a conventional Au disk electrode, as a consequence of the microdispersion of gold nanocrystals on the GC substrate. The morphological and electrochemical characteristics of the nAu‐GCE were evaluated by SEM and cyclic voltammetry. PAD using a very simple potential waveform consisting of an anodic potential (+700 mV for 500 ms) and a cathodic potential (?300 mV for 30 ms), was used to avoid the electrode surface fouling when histamine was detected under flowing conditions. Flow injection amperometric responses showed much higher I_p values and signal‐to‐noise ratios at the nAu‐GCE than at a conventional gold disk electrode. A limit of detection of 6×10^?7 mol L^?1 histamine was obtained. HPLC‐PAD at the nAu‐GCE was used for the determination of histamine in the presence of other biogenic amines and indole. Histamine was determined in sardine samples spiked at a 50 μg g^?1 concentration level, with good results. Furthermore, the chromatographic PAD method was also used for monitoring the formation of histamine during the decomposition process of sardine samples.     

纳米铂修饰玻碳电极对邻苯二酚的电化学氧化及测定

应用循环伏安法研究了邻苯二酚在纳米铂修饰玻碳(PtNPs/GC)电极上的电化学氧化行为。实验表明,PtNPs/GC电极对邻苯二酚有很强的电催化作用,其伏安扫描氧化峰电流随着温度的升高而增大,但氧化峰电位略有负移。常温下,邻苯二酚能自发在电极表面发生聚合反应,生成具有导电性的聚合膜,其催化氧化电流与邻苯二酚浓度在1.0×10-6mol/L~5.0×10-5mol/L范围内呈良好的线性关系,检出限为2.9×10-7mol/L。