Polypropylene nanocomposites with various functionalized‐multiwalled nanotubes: thermomechanical properties,morphology, gas permeation,and optical transparency

Polypropylene (PP) nanocomposites with three different functionalized‐multiwalled nanotubes (F‐MWNTs) are compared in terms of their thermomechanical properties, morphology, oxygen permeability, and optical transparency. The F‐MWNTs dodecanol‐MWNT, dodecylamine‐MWNT, and 1,1,1,3,3,3‐hexafluoro‐2‐phenyl‐2‐propanol‐MWNT were combined with PP to produce hybrid films. The variations of their properties with the matrix polymer F‐MWNT content are discussed. Transmission electron microscopy photographs show that most of the F‐MWNTs are dispersed homogeneously in the matrix polymer on the nanoscale, although some agglomerated F‐MWNT particles are formed. Even composites with low F‐MWNT contents (≤3 wt %) exhibit much better thermomechanical values than pure PP. The gas permeability of the hybrids was found to decrease linearly with increases in the F‐MWNT content of the PP matrix. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Structural and theoretical study of four novel norcantharidine derivatives: two new cases of conditional isomorphism

Structural and theoretical studies of four novel 5,6‐dehydronorcantharidine ( DNCA )/norcantharidine ( NCA ) derivatives, namely (3aR,4S,7R,7aS)‐2‐phenyl‐3a,4,7,7a‐tetrahydro‐4,7‐epoxy‐1H‐isoindole‐1,3(2H)‐dione, C₁₄H₁₁NO₃ ( DNCA‐A ), (3aR,4S,7R,7aS)‐2‐(4‐nitrophenyl)‐3a,4,7,7a‐tetrahydro‐4,7‐epoxy‐1H‐isoindole‐1,3(2H)‐dione, C₁₄H₁₀N₂O₅ ( DNCA‐NA ), (3aR,4S,7R,7aS)‐2‐(4‐nitrophenyl)‐3a,4,5,6,7,7a‐hexahydro‐1H‐4,7‐epoxyisoindole‐1,3(2H)‐dione, C₁₄H₁₂N₂O₅ ( NCA‐NA ), and (3aR,4S,7R,7aS)‐2‐(2‐hydroxyethyl)‐3a,4,5,6,7,7a‐hexahydro‐1H‐4,7‐epoxyisoindole‐1,3(2H)‐dione, C₁₀H₁₃NO₄ ( NCA‐AE ), are reported. The supramolecular interactions and single‐crystal structural characteristics of these molecules, together with the crystal structures of four other similar molecules, i.e. NCA‐A (the 4‐phenyl derivative of NCA‐NA ), DNCA‐AE (the 5,6‐unsaturated derivative of NCA‐AE ), DNCA and NCA , were analysed. Surprisingly, DNCA‐A and NCA‐A , as well as DNCA–NA and NCA‐NA , proved to be isomorphic, while DNCA‐AE and NCA‐AE , as well as DNCA and NCA , have very different crystal structures. These are very rare isostructural examples between unsaturated and saturated oxanorbornene/oxanorbornane derivatives. To further explore how noncovalent interactions (NCIs) affect the degree of isomorphism in this particular series of rigid molecules where there is a fairly limited conformational degree of freedom, all four pairs of crystal structures were analyzed in parallel. The differentiation in NCIs which entails the packing mode of similar molecules is supported by energy calculations based on real or exchanged crystal structures. Our results show that minor structural differences may result in very different supramolecular interactions, and so lead to altered packing modes in the crystalline solids. Even if isostructurality sometimes occurs, the possibility of various molecular packing types cannot be ruled out. On the other hand, isomorphism may just be the result of kinetic possibilities instead of relative thermodynamic stabilities. Though crystal structure prediction is formidable, the comparison method based on existing crystal structures and quantum calculations can be used to predict the probability of isomorphism. This understanding will help us to design new norbornene derivatives with specified structures.     

Preparation,properties, and application of polypropylene micro/nanofiber membranes

Nanofiber membranes have huge potential applications in many areas due to their unique properties. However, the thermoplastic micro/nanofiber membranes were rarely reported. In this paper, polypropylene (PP) nanofibers were prepared by melt extrusion of immiscible blends of PP, cellulose acetate butyrate (CAB), and subsequent removal of the CAB matrix. The wet‐laid application was used to make PP nanofiber membranes and PP‐g‐MAH/nonwoven micro/nanofiber membrane. The properties of membranes including morphology, apparent density, porosity, contact‐angle, pore size distribution, and water flux were characterized. The results showed that the consequent membranes were provided with optimistic porosity and pore size distribution. Moreover, they were all with high pure water fluxes, which were superior to that of PP microporous membrane. They performed an excellent separation performance of TiO₂ suspension and dyeing wastewater. The work revealed this method could be an efficient one to make thermoplastic polymer micro/nanofiber membranes, and they would have a brilliant potential application for water treatment. Copyright © 2010 John Wiley & Sons, Ltd.     

Fabrication and characterization of SiO2/PVDF composite nanofiber‐coated PP nonwoven separators for lithium‐ion batteries

SiO₂/polyvinylidene fluoride (PVDF) composite nanofiber‐coated polypropylene (PP) nonwoven membranes were prepared by electrospinning of SiO₂/PVDF dispersions onto both sides of PP nonwovens. The goal of this study was to combine the good mechanical strength of PP nonwoven with the excellent electrochemical properties of SiO₂/PVDF composite nanofibers to obtain a new high‐performance separator. It was found that the addition of SiO₂ nanoparticles played an important role in improving the overall performance of these nanofiber‐coated nonwoven membranes. Among the membranes with various SiO₂ contents, 15% SiO₂/PVDF composite nanofiber‐coated PP nonwoven membranes provided the highest ionic conductivity of 2.6 × 10^?3 S cm^?1 after being immersed in a liquid electrolyte, 1 mol L^?1 lithium hexafluorophosphate in ethylene carbonate, dimethyl carbonate and diethyl carbonate. Compared with pure PVDF nanofiber‐coated PP nonwoven membranes, SiO₂/PVDF composite fiber‐coated PP nonwoven membranes had greater liquid electrolyte uptake, higher electrochemical oxidation limit, and lower interfacial resistance with lithium. SiO₂/PVDF composite fiber‐coated PP nonwoven membrane separators were assembled into lithium/lithium iron phosphate cells and demonstrated high cell capacities and good cycling performance at room temperature. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1719–1726     

Morphology and mechanical behavior of isotactic polypropylene with different stereo‐defect distribution in injection molding

Large amount of work has been published on the isotacticity–properties relationship of isotactic polypropylene (iPP). However, the stereo‐defect distribution dependence of morphology and mechanical properties of iPP injection molding samples is still not clear. In this study, two different isotactic polypropylene (iPP) resins (PP‐A and PP‐B) with similar average isotacticity but different stereo‐defect distribution were selected to investigate the morphology evolution and mechanical properties (tensile and notching) of their injection molding samples using differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), 2D wide angle X‐ray diffraction (2D‐WAXD), and scanning electron microscope (SEM). The results of DMA showed that the molecular movement ability of PP‐A (with less uniform distribution of stereo‐defect) was stronger than that of PP‐B, meanwhile the analysis of DSC and SEM suggested that after injection molding, smaller spherullites, and crystals with higher perfection had formed in the specimens of PP‐A. The resulting of tensile properties of PP‐A were found to be better than that of PP‐B. The results of morphology evolution by SEM observation and 2D‐WAXD showed that PP‐A is more likely to occur interspherulite deformation and can disperse the tensile stress more efficiently, and therefore, its crystal structure can withstand a greater force when tensile stress is applied. On the other hand, PP‐B has larger spherulites and boundaries, and low perfection of lamellaes, and the intraspherulte deformation tend to take place. It is easier for the crystal of PP‐B to be broken up and reoriented along the tensile direction. Copyright © 2014 John Wiley & Sons, Ltd.     

Diffusion measurements with fourier transform infrared attenuated total reflectance spectroscopy: Water diffusion in polypropylene*

The diffusion of pure liquid water into a commercial polypropylene (PP) film at 278–348 K was studied with Fourier transform infrared attenuated total reflectance spectroscopy. Abnormal diffusion behavior was indicated by a significant deviation between the experimental data and a Fickian diffusion model with the conventional saturated boundary condition applied at the water/PP interface. This deviation was observed at all the temperatures studied. With a modified boundary condition that took into account a mass‐transfer resistance at the water/PP interface, the Fickian model was able to represent the experimental data satisfactorily. The average water diffusion coefficient varied between 1.41 and 7.64 × 10^?9 cm²/s, with an activation energy of diffusion of about 19.3 kJ/mol. The interfacial mass‐transfer resistance was represented by an exponential model with an empirical relaxation parameter. The relaxation parameter β increased as the temperature increased and reached an apparent plateau. The infrared spectrum indicated a positive chemical shift of 18 cm^?1 for the less strongly hydrogen‐bonded component of the broad hydroxyl stretching band with respect to pure liquid water, indicating that hydrogen‐bonding interactions were weakened or broken when water molecules diffused into the PP matrix. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 980–991, 2002     

Preparation of β2‐Amino Acid Derivatives (β2hThr, β2hTrp, β2hMet, β2hPro, β2hLys,Pyrrolidine‐3‐carboxylic Acid) by Using DIOZ as Chiral Auxiliary

The title compounds were prepared from valine‐derived N‐acylated oxazolidin‐2‐ones, 1 – 3, 7, 9 , by highly diastereoselective (≥ 90%) Mannich reaction (→ 4 – 6 ; Scheme 1) or aldol addition (→ 8 and 10 ; Scheme 2) of the corresponding Ti‐ or B‐enolates as the key step. The superiority of the ‘5,5‐diphenyl‐4‐isopropyl‐1,3‐oxazolidin‐2‐one’ (DIOZ) was demonstrated, once more, in these reactions and in subsequent transformations leading to various t‐Bu‐, Boc‐, Fmoc‐, and Cbz‐protected β²‐homoamino acid derivatives 11 – 23 (Schemes 3–6). The use of ω‐bromo‐acyl‐oxazolidinones 1 – 3 as starting materials turned out to open access to a variety of enantiomerically pure trifunctional and cyclic carboxylic‐acid derivatives.     

Hydrophobic polyphenylalanine-grafted hyperbranched polyethylenimine and its in vitro gene transfection

A series of amphiphilic multi‐armed PPn copolymers were prepared by ROP of Phe‐NCA with PEI‐25k as a macroinitiator. The particle size of the PPn/DNA complexes was about 100 nm and the zeta potentials were below 20 mV. An MTT assay demonstrated that all the PPn copolymers had lower cytotoxicity compared to PEI‐25k. In vitro gene transfection studies were also conducted in HeLa, 293 and CT 26 cells. The optimal quantity of hydrophobic phenylalanine segments in PP80 led to higher transfection efficiency in various cell lines based on this study. The results indicate that PP80 was the best candidate for gene delivery among these PPn copolymers.

     

Structure-based design of a highly selective catalytic site-directed inhibitor of Ser/Thr protein phosphatase 2B (calcineurin)

Protein serine/threonine phosphatases (PP1, PP2A and PP2B) play important roles in intracellular signal transductions. The immunosuppressant drugs FK506 and cyclosporin A (CsA) bind to immunophilins, and these complexes selectively inhibit PP2B (calcineurin), leading to the suppression of T-cell proliferation. Both FK506 and CsA must, however, form complexes with immunophilins to exert their inhibitory action on PP2B. Thus, it is of interest to find a direct and selective inhibitor of PP2B that does not involve the immunophilins as a biological tool for studies of PP2B and also as a candidate therapeutic agent. We selected the simple natural product cantharidin, a known PP2A-selective inhibitor, as a lead compound for this project. Primary SAR indicated that norcantharidin (7-oxabicyclo[2.2.1]heptane-2,3-dicarboxylic anhydride) inhibits not only PP1 and PP2A but also PP2B, and a binding model of norcantharidin carboxylate to the PP2B catalytic site was computationally constructed. Based on this binding model, we designed and synthesized several cantharidin derivatives. Among these compounds, 1,5-dibenzoyloxymethyl-substituted norcantharidin was found to inhibit PP2B without inhibiting PP1 or PP2A. To our knowledge, this is the first highly selective catalytic site-directed inhibitor of PP2B.     

Synthesis of homopolypeptides with PPII structure

Polyprolines are attractive polymers because of their folding property into polyproline II (PPII) structure, their significance in protein/protein interactions, and their potential as new therapeutic targets. Silaproline (Sip) is an analogue of proline, which exhibits similar conformational properties. The presence of dimethylsilyl group confers to Sip a higher lipophilicity as well as an improved resistance to biodegradation. Enantiomerically pure Sip was available in gram quantities from resolution of the enantiomers by chiral high performance liquid chromatography. This study describes the first synthesis of Sip N‐carboxyanhydride (NCA) and shows preliminary results on comparison of polymerization of (l )Pro‐NCA and (d )Sip‐NCA to obtain homopolypeptides with PPII structure, polyproline, and polysilaproline polymers. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3103–3109     

Synthesis and antiproliferative evaluation of oxime,methyloxime, and amide‐containing quinazolinones

Certain oxime, methyloxime, and amide‐containing quinazolinone derivatives were synthesized and evaluated in vitro for their antiproliferative activities against a panel of human cancer cell lines including nasopharyngeal carcinoma (NPC‐TW01), lung carcinoma (NCI‐H226), and leukemia (Jurkat). Quinazolinone 2 was inactive against all three cell lines tested, while quinazolinone 4 was weakly active against both Jurkat and H226 cancer cells with IC₅₀ values of 6.55 and 12.27 μM, respectively, indicating that the oxime derivative 4 is more favorable than its ketone precursor 2 . Our results have also indicated that quinazolinone 8g and its biphenyl counterpart 8f exhibited more potent antiproliferative activities than the positive control methotrexate against all three cancer cell lines tested. Among these quinazolinone derivatives, 8g was the most active against NPC‐TW01 with an IC₅₀ value of 4.78 μM. Further study on NPC‐TW01 cell cycle distribution indicated that the compound 8g induced cell arrest at the G1/G0 phase in a time‐ and concentration‐dependent manner. Moreover, a characteristic hypo‐diploid DNA content peak (sub‐G1) was found to increase from 1 to 4% in NPC‐TW01 cells treated with 8g for 72 hr. These results indicate that 8g can induce cells arrest in the G1/G0 phase and cause cell death. Further structural optimization of 8g and detailed study of its antiproliferative mechanism are going on.     

Synthesis and Self‐assembly of a Helical Polymer Grafted from a Foldable Polyurethane Scaffold

Herein a polyurethane graft poly‐l ‐glutamate amphiphilic copolymer was synthesized from a polyurethane (PU)‐based macro‐initiator (containing pendant primary amine groups) through the ring opening polymerization of N‐carboxy anhydride of γ‐benzyl‐l ‐glutamate ( BLG‐NCA ). On average, twenty two l ‐glutamic acids were grafted from each amino group which was pendant on the polyurethane chain with 10 repeating units. The grafted polymer ( PU‐PP‐1 ) exhibits self‐assembly to produce a hydrogel in a wide pH window ranging from pH 5.0 to 8.0 with a critical gelation concentration (CGC) of 5.0 wt % (w/v) at pH 7.4. Furthermore, circular dichroism study revealed the transition of the α‐helix to a random coil upon increasing the pH. Due to the protonation of side chains at pH 4.0, PU‐PP‐1 adopted an α‐helical conformation whereas at pH >8.0 the side‐chain carboxylic acid groups of the PLGAs were ionized, leading to the formation of an extended random coil conformation as a result of charge repulsion. Conformational switching was also supported by FTIR spectroscopy.     

EFFECT OF N,N,N’,N’-TETRAALKYL TEREPHTHALAMIDE ON NON-ISOTHERMAL CRYSTALLIZATION KINETICS OF POLYPROPYLENE

The effect of N,N,N＇,N＇-tetraalkyl terephthalamide （TATA） on the non-isothermal crystallization and melting characteristics ofpolypropylene （PP） was studied. The addition of TATA can lead to the formation ofβ-crystal PP. With the increase in TATA concentration the degree of crystallinity for β-crystal PP increased significantly, and that for a-crystal PP decreased, which indicated that TATA effectively induced the formation of β-crystal PP. WAXD also revealed the existence of β-crystal PP after the introduction of TATA into PP. PP containing TATA crystallized at a temperature range of 5-10℃ higher than that of pure PP, and the half-crystallization time （t1/2） and Avrami exponent （n） of PP at the same cooling rate were decreased by the addition of TATA, indicating that TATA influenced the crystallization rate and crystallization growth mode of PP. The rate constant of crystallization of PP containing TATA （Zc） was larger than that of pure PP, which further indicated that the crystallization of PP was accelerated by the addition of TATA.     

Crystallization,melting behavior,and morphology of PP/Novolac blends

The crystallization, melting behavior, and morphology of Polypropylene (PP) and PP/Novolac blends were studied by scanning electron microscopy, wide angle X‐ray diffraction, differential scanning calorimetry, and polarized optical microscope. The results showed that the crystallization of PP in PP/Novolac blends was strongly influenced by crystallization temperature, particles size of Novolac, crosslinking, and compatibilizer maleic anhydride‐grafted PP. The Novolac resin could not only affect the crystal structure, but also acted as effective nucleating agents, accelerating the crystallization of PP in the PP/Novolac blends. And the smaller the Novolac particles were, the more effective were the nucleating agent for PP crystallization. Avrami equation was used to analyze the isothermal crystallization kinetics of PP and PP/Novolac blends. The influences of curing and compatibilizer on the crystallization behavior of PP were rather complicated. The crystallization thermodynamics were estimated using the Hoffman theory. The incorporation of cured Novolac and compatibilizer evidently decreased the chain folding energy of PP. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3288–3303, 2006     

间位取代卟啉及其锌卟啉的电子吸收光谱

取代的卟啉类衍生物在气敏传感器方面具有广泛的应用前景.本文采用了密度泛函理论(DFT)和含时密度泛函理论(TD-DFT)研究了四种不同取代基的卟啉衍生物(meso位四硝基苯基/四氨基苯基卟啉(NO2PP,NH2PP)及其相应的锌金属卟啉衍生物(NO2ZnPP,NH2ZnPP))的紫外和近紫外光谱特征.利用两种不同的交换相关泛函(广义梯度近似泛函(PBE)和杂化密度泛函(B3LYP))优化了上述四种物质的结构,并应用TD-DFT计算了相应的电子激发能量和振动强度.结果表明,取代卟啉的吸收光谱与大量的电子跃迁有关;与B3LYP泛函预测的光谱相比,PBE泛函所得B带以及Q带的波长位置与实验值更为接近.另外,计算所得硝基取代基卟啉的B带相对于氨基取代基卟啉的B带发生了红移,这与实验现象也保持一致.由于卟啉衍生物的三重激发态在电子转移中有很重要的应用,因此在PBE/6-31G(d)水平上计算了四种物质的最低三重激发态能量,分别为1.426、1.469、1.608和1.581eV.     

Comparison of the effect of mica and talc and chemical coupling on the rheology,morphology, and mechanical properties of polypropylene composites

The effect of filler types of mica and talc on the oscillatory shear rheological properties, mechanical performance, and morphology of the chemically coupled polypropylene composites is studied in this work. The Maleic Anhydride grafted Polypropylene (MAPP) was used as an adhesion promoter for coupling mineral particles with the polypropylene matrix. The samples were prepared by a co‐rotating, L/D = 40, 25 mm twin screw extruder. The tensile tests carried out on the injection molded samples showed a reinforcing effect of talc up to 20 wt% on the Polypropylene (PP). The tensile strength of PP‐mica composites showed a slight decrease at all percentages of mica. The effect of chemical coupling by using MAPP on the tensile strength was more pronounced in increasing the tensile strength for PP‐mica than PP‐talc composites. The complex viscosity curve of pure PP and the composites, showed a Newtonian plateau (η₀) up to 30 wt% at low frequency terminal zone. By increasing the filler content to 40 and 50 wt%, the complex viscosity at very low shear rates sharply increased and showed yield behavior that can be due to the formation of filler particles networks in the melt. At the optimum amount of coupling agent, a minimum in cross over frequency curve against MAPP content is observed. The optimum amount of coupling agent for PP‐talc composites is about 1.5%, and about 3% for PP‐mica formulations. The analysis of viscosity behavior at power‐law high region, revealed the more shear thinning effect of mica than talc on the PP matrix resin. Copyright © 2009 John Wiley & Sons, Ltd.     

Poly (diallyldimethylammonium) and polyphosphate polyelectrolyte complexes as an all‐in‐one flame retardant for polypropylene

Poly (diallyldimethylammonium chloride) (PDDA) and ammonium polyphosphate (APP) deionized chloride ions and ammonium ions by ionizing in aqueous solution respectively, then combined to form poly (diallyldimethylammonium) and polyphosphate (PAPP) polyelectrolyte complexes as an all‐in‐one flame retardant for polypropylene and its composites were characterized by Fourier transform infrared (FTIR) spectroscopy and X‐ray photoelectron spectroscopy. One flame retardant system composed of PAPP and PP, the other flame retardant system composed of PAPP, Polyamide‐6 (PA6) and PP were tested by limiting oxygen index (LOI), UL‐94, cone calorimeter tests and thermogravimetric analysis (TGA) and compared with pure PP. The results showed that the LOI value of PP/PAPP composite can reach 27.5%, and UL‐94 V‐2 rating can be reached at 25 wt% PAPP loading. Meanwhile the cone calorimetry results displayed that the peak heat release rate (PHRR) and total heat release (THR) were reduced up to 69.3% and 22.5%, respectively, compared with those of pure PP. After adding 5 wt% PA6, the carbon source missing due to the early PAPP decomposition can be made up, and PHRR and THR can be further reduced slightly. The flame retardant mechanism of PAPP was studied by FTIR spectroscopy and X‐ray photoelectron spectroscopy. Six‐membered ring of C─N containing conjugate double bonds, cross‐linked phosphate structure formed stable, intumescent, compact char layer which greatly improved the flame retardancy of PP.     

Effect of silane‐grafted polypropylene on the morphology of polypropylene and nylon 6/clay composites

Polypropylene (PP)/nylon 6/clay composites were prepared by compounding of PP, which had previously been treated with two kinds of silane compounds, with a master batch composed of 90 wt % of nylon 6 and 10 wt % of octadecyl amine‐modified sodium montmorillonite (NM10). The morphology of the composites was investigated by means of SEM, TEM, XRD, and energy‐dispersive X‐ray analysis. All of the composites exhibited a phase‐separated morphology, irrespective of whether the PP was modified with the silane compounds or not. However, adhesive strength between the modified PP and NM10 was stronger than that between neat PP and NM10. Moreover, the PP grafted with 3‐(trimethoxysilyl)propyl methacrylate (PP2) reacted with the silanol groups of the clay to form PP‐clay hybrid during the compounding, which acted as a compatibilizer for the PP/nylon 6/clay composite. PP2NM composite (PP2/NM10 80/20 on weight basis) exhibited a peculiar morphology, in that the PP‐rich phase formed island domains within the nylon 6‐rich domains, which were in turn dispersed in the PP‐rich continuous matrix. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 607–615, 2007.     

Crystallization behavior and morphology of β‐nucleated isotactic polypropylene with different stereo‐defect distribution

Aiming at further investigating the combination effect of concentration of β‐nucleating agent (β‐NA) and stereo‐defect distribution on the crystallization behavior of β‐nucleated isotactic polypropylene (β‐iPP), in this study, the crystallization behavior and polymorphic morphology of twoβ‐iPP resins with nearly same average isotacticity (PP‐A and PP‐B) but different uniformities of stereo‐defect distribution were investigated by differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD) and polarized optical microscopy (POM). The results of DSC and WAXD showed that the addition of TMB‐5 increases the crystallization temperature and decreases the spherulite sizes of both PP‐A and PP‐B, and reduces their crystallization energy barriers as well; however, the polymorphic behaviors of PP‐A and PP‐B exhibit different dependence on the TMB‐5 concentration. For PP‐A with less uniform distribution of stereo‐defects, β‐phase can be observed only when the TMB‐5 concentration is no less than 0.1 wt.%, while for PP‐B with more uniform stereo‐defect distribution, addition of 0.01 wt.% TMB‐5 can induce the formation of β‐phase. Moreover, the analysis of POM indicated that the crystalline morphologies of both PP‐A and PP‐B change greatly with the TMB‐5 concentration, and the variation features of PP‐A and PP‐B are quite different from each other. PP‐B with more uniform stereo‐defect distribution was more favorable for the formation of large amount of β‐phase in the presence of wide concentration range of TMB‐5. The different polymorphic behaviors and their different dependences on the β‐NA concentration were related to the different uniformities of stereo‐defect distribution of the samples, since the distribution of stereo‐defects could restrain the regular insertion of molecular chains during crystallization and thus determine the tendency the α‐phase crystallization of the sample. Copyright © 2014 John Wiley & Sons, Ltd.     

Combined effects of clay modifications and compatibilizers on the formation and physical properties of melt‐mixed polypropylene/clay nanocomposites

The melt mixing technique was used to prepare various polypropylene (PP)‐based (nano)composites. Two commercial organoclays (denoted 20A and 30B) served as the fillers for the PP matrix, and two different maleated (so‐called) compatibilizers (denoted PP‐MA and SMA) were employed as the third component. The results from X‐ray diffraction (XRD) and transmission electron microscope (TEM) experiments revealed that 190 °C was an adequate temperature for preparing the nanocomposites. Nanocomposites were achieved only if specific pairs of organoclay and compatibilizer were simultaneously incorporated in the PP matrix. For example, PP/20A(5 wt %)/PP‐MA(10 wt %) and PP/30B(5 wt %)/SMA(5 wt %) composites exhibited nanoscaled dispersion of 20A or 30B in the PP matrix. Differential scanning calorimetry (DSC) results indicated that the organoclays served as nucleation agents for the PP matrix. Generally, their nucleation effectiveness increased with the addition of compatibilizers. The thermal stability enhancement of PP after adding 20A was confirmed with thermogravimetric analysis (TGA). The enhancement became more evident as a suitable compatibilizer was further added. However, for the 30B‐included composites, thermal stability enhancement was not evident. The dynamic mechanical properties (i.e., storage modulus and loss modulus) of PP increased as the nanocomposites were formed; the properties increment corresponded to the organoclay dispersion status in the matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4139–4150, 2004