Direct Electrochemistry of Cytochrome c on a Silica Sol‐Gel Film Modified Electrode

Dilute silica sol‐gel was simply dropped on the surface of a basal plane graphite electrode (BPGE) to form a silica sol‐gel film modified electrode. Direct electrochemical response of cytochrome c (Cyt c) on the modified electrode was observed by cyclic voltammetry (CV). The results suggested that Cyt c could be tightly adsorbed on the surface of the silica sol‐gel film modified electrode. A couple of well‐defined and nearly reversible redox peaks can be observed in a phosphate buffer solution (pH 7.0), which anodic and cathodic peak potentials were at ?0.243 and ?0.306 V (vs. Ag/AgCl), respectively. Cyt c adsorbed on the surface of silica sol‐gel film shows a remarkable electrocatalytic activity for the reduction of oxygen. Based on these, a third‐generation biosensor could be constructed to detect the concentration of oxygen in aqueous solution.     

Electrochemically‐controlled DNA Release under Physiological Conditions from a Monolayer‐modified Electrode

An indium tin oxide (ITO) electrode prepared on a flexible polymeric support was modified with an amino‐silane and then functionalized with trigonelline and 4‐carboxyphenylboronic acid covalently bound to the amino groups. The trigonelline species containing quarterized ammonium group produced positive charge on the electrode surface regardless of the pH value, while the phenylboronic acid species were neutral below pH 8 and negatively charged above pH 9 (note that their pK_a=8.4). The total charge on the monolayer‐modified electrode was positive at the neutral pH and negative at pH>9 (note that 4‐carboxyphenylboronic acid was attached to the electrode surface in excess to trigonelline, thus allowing the negative charge to dominate on the electrode surface at basic pH). Single‐stranded DNA molecules were loaded on the modified electrode at pH 7.0 due to their electrostatic attraction to the positively charged surface. By applying electrolysis at −1.0 V (vs. Ag/AgCl reference) electrochemical oxygen reduction resulted in the consumption of hydrogen ions and local pH increase in the vicinity of the electrode surface. The process resulted in the transition to the total negative charge due to the negative charges formed on the phenylboronic acid species. This resulted in the electrostatic repulsion and release of the loaded DNA. The developed approach allowed the electrochemically‐triggered DNA release not only in the aqueous solutions, but also in human serum solution, thus giving promise for future biomedical applications.     

One‐step synthesis of Ag@PS nanospheres via flash nanoprecipitation

In the work reported, we utilized a facile flash nanoprecipitation process to generate Ag nanoparticles@nanospheres polymer composites. Ag nanoparticles can be loaded onto the polymeric polystyrene (PS) nanosphere surface using a simple and inexpensive method through in situ growth; the amount of loaded Ag nanoparticles and the size of holes on the PS surface prepared by flash nanoprecipitation can be fine‐tuned by changing the pH of the water medium and the PS nanoparticles should have a greater specific area. The as‐synthesized Ag@PS composite nanoparticles obtained via the one‐step and continuous preparation route show high catalytic activity in the reduction reaction of 4‐nitrophenol. Importantly, the nanoparticles show no loss of catalytic performance over five cycles.     

Determination of Ag(I), Hg(II) and Pb(II) by using silica gel loaded with dithizone and zinc dithizonate

The modified sorbents with dithizone and zinc dithizonate adsorbed on the silica surface were obtained. The adsorption of heavy metal ions from aqueous solutions onto loaded silicas was studied. Color scales for Ag(I), Hg(II) and Pb(II) visual test detection were worked out. The modified silica gels were established to be applicable to semi-quantitative determination of these metal ions in buttermilk, natural, mineral and waste water.     

2‐Aminobenzenethiol‐Functionalized Silver‐Decorated Nanoporous Silicon Photoelectrodes for Selective CO2 Reduction

A molecularly thin layer of 2‐aminobenzenethiol (2‐ABT) was adsorbed onto nanoporous p‐type silicon (b‐Si) photocathodes decorated with Ag nanoparticles (Ag NPs). The addition of 2‐ABT alters the balance of the CO₂ reduction and hydrogen evolution reactions, resulting in more selective and efficient reduction of CO₂ to CO. The 2‐ABT adsorbate layer was characterized by Fourier transform infrared (FTIR) spectroscopy and modeled by density functional theory calculations. Ex situ X‐ray photoelectron spectroscopy (XPS) of the 2‐ABT modified electrodes suggests that surface Ag atoms are in the +1 oxidation state and coordinated to 2‐ABT via Ag?S bonds. Under visible light illumination, the onset potential for CO₂ reduction was ?50 mV vs. RHE, an anodic shift of about 150 mV relative to a sample without 2‐ABT. The adsorption of 2‐ABT lowers the overpotentials for both CO₂ reduction and hydrogen evolution. A comparison of electrodes functionalized with different aromatic thiols and amines suggests that the primary role of the thiol group in 2‐ABT is to anchor the NH₂ group near the Ag surface, where it serves to bind CO₂ and also to assist in proton transfer.     

Enhancement of thermoelectric performance of Na<Subscript>x</Subscript>Co<Subscript>2</Subscript>O<Subscript>4</Subscript> with Ag dispersion by precipitation from Ag<Superscript>+</Superscript> aqueous solution

Thermoelectric Na_xCo₂O₄/Ag composites were synthesized by citric acid complex (CAC) method and Ag precipitation from CH₃COOAg aqueous solution on the Na_xCo₂O₄ powders. Effects of the synthesis process on microstructure and thermoelectric performance of Na_xCo₂O₄/Ag composites were investigated. When the Na_xCo₂O₄ CAC powders were dipped in CH₃COOAg aqueous solution and dried, fine Ag particles less than around 300 nm in size were precipitated on the surface of Na_xCo₂O₄ powders. After the subsequent sintering process, the flaky Ag phase, the length and thickness of which were up to 5 and 1 μm, respectively, existed along interfaces between Na_xCo₂O₄ grains. The sizes of Ag particles obtained in this study were found to be smaller than those of the conventionally prepared Na_xCo₂O₄/Ag composites. The fine dispersion of Ag grains was effective for suppressing the increase in thermal conductivity due to the addition of metallic phase, Ag, and for improving the thermoelectric performance of Na_xCo₂O₄/Ag composites, suggesting that the synthesis technique composed of the CAC method and Ag precipitation from CH₃COOAg aqueous solution is significantly important process for thermoelectric Na_xCo₂O₄/Ag composites.     

A Facile One‐Pot Synthesis of Layered Protonated Titanate Nanosheets Loaded with Silver Nanoparticles with Enhanced Visible‐Light Photocatalytic Performance

Layered protonated titanate nanosheets (LPTNs) loaded with silver nanoparticles are prepared by a simple one‐pot hydrothermal route in silver‐ammonia solution. The as‐synthesized Ag‐loaded LPTNs possess large specific surface area. The Ag nanoparticles are highly dispersed on the surface of the LPTNs. They have negligible effects on the crystal structure, crystallinity, and surface area of the LPTNs but result in considerable enhancement of visible‐light absorption and in a red‐shift of the band gap for the LPTNs. The Ag‐loaded LPTNs show enhanced photocatalytic activity for both liquid‐ and gas‐phase reactions under visible‐light irradiation. Moreover, the photocatalytic activity first increases gradually with increasing Ag loading content, and then decreases after maximizing at an optimal Ag content. At the Ag loading content of 2.87 mol % and 1.57 mol %, the Ag‐loaded LPTNs exhibit the highest visible‐light photocatalytic activity for degradation of rhodamine B in water and mineralization of benzene in air, respectively. An alternative possible mechanism for the enhancement of the visible‐light photocatalytic activity is also proposed.     

A quantum chemical study of the structure of fluorinated silver acetate(I) monomers and dimers

Quantum chemical calculations of the equilibrium structure, potential energy surface cross-sections along the nonrigid degrees of freedom of (CF₃COOAg)₂, (CHF₂COOAg)₂, (CH₂FCOOAg)₂, and (CH₃COOAg)₂ dimers and the corresponding monomers are presented. The B3LYP method with the augmented cc-pVTZ basis set for C, O, F atoms and the Stuttgart 1997 RSC basis set together with the relativistic effective potential for Ag atoms is used. It is shown that in all dimers the eight-membered ring is a rather rigid planar fragment, and the Ag atoms can be bonded with the bond order of 0.2 in dimers. Almost free rotation of acyclic groups around the C-C bond in (CH₃COOAg)₂ and (CF₃COOAg)₂ dimers transforms into a hindered one in the (CHF₂COOAg)₂ dimer, and further into the existence of syn- and anti-structures divided by a high rotation barrier in the (CH₂FCOOAg)₂ dimer. In monomers, the ratio of the internal rotation barriers is similar. With increasing number of fluorine substitution for hydrogen atoms in dimers the Ag-Ag bond length is found to increase (2.79 Å, 2.81 Å, 2.83 Å, 2.84 Å) and the ring rigidity to simultaneously decrease in the acetate-triflouroacetate series.     

Determination of Iodide and Idoxuridine at a Glutaraldehyde‐Cross‐Linked Poly‐L‐Lysine Modified Glassy Carbon Electrode

The detection limit (about 0.017 μg mL^?1) for voltammetric determination of iodide (peak at +0.87 V vs. Ag/AgCl at pH 2) at a glutaraldehyde‐cross‐linked poly‐L ‐lysine modified glassy carbon electrode involving oxidation to iodine was found to be several orders of magnitude lower than that for the voltammetric determination on a bare glassy carbon electrode. This method was applied successfully to the determination of iodide in two medicinal formulations. Idoxuridine was determined indirectly at the same electrode by accumulating it first at ?0.8 V vs. Ag/AgCl. At this potential the C? I bond in the adsorbed idoxuridine is reduced giving iodide, which is then determined at the modified electrode. The method was successfully applied to the determination of idoxuridine in a urine sample.     

Poly(γ‐benzyl‐L‐glutamate)‐functionalized single‐walled carbon nanotubes from surface‐initiated ring‐opening polymerizations of N‐carboxylanhydride

Single‐walled carbon nanotubes (SWCNTs) have been functionalized with poly(γ‐benzyl‐L ‐glutamate) (PBLG) by ring‐opening polymerizations of γ‐benzyl‐L ‐glutamic acid‐based N‐carboxylanhydrides (NCA‐BLG) using amino‐functionalized SWCNTs (SWCNT‐NH₂) as initiators. The SWCNT functionalization has been verified by FTIR spectroscopy and transmission electron microscopy. The FTIR study reveals that surface‐attached PBLGs adopt random‐coil conformations in contrast to the physically absorbed or bulk PBLGs, which exhibit α‐helical conformations. Raman spectroscopic analysis reveals a significant alteration of the electronic structure of SWCNTs as a result of PBLG functionalization. The PBLG‐functionalized SWCNTs (SWCNT‐PBLG) exhibit enhanced solubility in DMF. Stable DMF solutions of SWCNT‐PBLG/PBLG with a maximum SWCNTs concentration of 259 mg L^?1 can be readily obtained. SWCNT‐PBLG/PBLG solid composites have been characterized by differential scanning calorimetry, thermogravimetric analysis, wide/small‐angle X‐ray scattering (W/SAXS), scanning electron microscopy, and polarized optical microscopy for their thermal or morphological properties. Microfibers containing SWCNT‐PBLG and PBLG can also be prepared via electrospinning. WAXS characterization reveals that SWCNTs are evenly distributed among PBLG rods in solution and in the solid state where PBLGs form a short‐range nematic phase interspersed with amorphous domains. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2340–2350, 2010     

Spatially Controllable DNA Condensation by a Water‐Soluble Supramolecular Hybrid of Single‐Walled Carbon Nanotubes and β‐Cyclodextrin‐Tethered Ruthenium Complexes

A supramolecular hybrid is prepared by the supramolecular surface modification of single‐walled carbon nanotube (SWCNT) with cationic β‐cyclodextrin‐tethered ruthenium complexes through a spacer molecule that contains both an adamantane and a pyrene moiety. By employing the supramolecular hybrid, spatially controllable DNA condensation along the SWCNT skeleton is achieved by anchoring cationic ruthenium complexes on the surface. Furthermore, because of the unique physiological properties of SWCNTs, the cationic supramolecular hybrid can be used as a nonviral gene delivery system with the ruthenium complexes as a fluorescent probe to monitor uptake of DNA by cells.     

A Surfactant‐Encapsulating Polyoxometalate Nanowire Assembly as a New Carrier for Nanoscale Noble‐Metal Catalysts

The loading of noble‐metal nanoparticles (NMNPs) onto various carriers to obtain stable and highly efficient catalysts is currently an important strategy in the development of noble metal (NM)‐based catalytic reactions and their applications. We herein report a nanowire supramolecular assembly constructed from the surfactant‐encapsulating polyoxometalates (SEPs) CTAB‐PW₁₂, which can act as new carriers for NMNPs. In this case, the Ag NPs are loaded onto the SEP nanowire assembly with a narrow size distribution from 5 to 20 nm in diameter; the average size is approximately 10 nm. The Ag NPs on the nanowire assemblies are well stabilized and the over agglomeration of Ag NPs is avoided owing to the existence of well‐arranged polyoxometalate (POM) units in the SEP assembly and the hydrophobic surfactant on the surface of the nanowire assembly. Furthermore, the loading amount of the Ag NPs can be adjusted by controlling the concentration of the AgNO₃ aqueous solution. The resultant Ag/CTAB‐PW₁₂ composite materials exhibit high activity and good stability for the catalytic reduction of 4‐nitrophenol (4‐NP) with NaBH₄ in isopropanol/H₂O solution. The NMNPs‐loaded SEP nanoassembly may represent a new composite catalyst system for application in NM‐based catalysis.     

Determination of Fe(II), Cu(II) and Ag(I) by using silica gel loaded with 1,10-phenanthroline

The modified silica gel with 1,10-phenanthroline adsorbed was obtained. The adsorption from aqueous solutions onto loaded silica gel of Fe(II), Cu(II) and Ag(I) and their complexes was studied. The loaded silica gel was applied to Fe(II), Cu(II) and Ag(I) reflectance spectroscopy determinations in water (detection limits 0.08, 0.03 and 0.01 ppm respectively). Visual test scales for Fe, Cu and Ag ion determinations in water were worked out.     

Electrochemically Stimulated Insulin Release from a Modified Graphene‐functionalized Carbon Fiber Electrode

A graphene‐functionalized carbon fiber electrode was modified with adsorbed polyethylenimine to introduce amino functionalities and then with trigonelline and 4‐carboxyphenylboronic acid covalently bound to the amino groups. The trigonelline species containing quarterized pyridine groups produced positive charge on the electrode surface regardless of the pH value, while the phenylboronic acid species were neutral below pH 8 and negatively charged above pH 9 (note that their pK_a=8.4). The total charge on the monolayer‐modified electrode was positive at the neutral pH and negative at pH > 9. Note that 4‐carboxyphenylboronic acid was attached to the electrode surface in molar excess to trigonelline, thus allowing the negative charge to dominate on the electrode surface at basic pH. Negatively charged fluorescent dye‐labeled insulin (insulin‐FITC) was loaded on the modified electrode surface at pH 7.0 due to its electrostatic attraction to the positively charged interface. The local pH in close vicinity to the electrode surface was increased to ca. 9–10 due to consumption of H⁺ ions upon electrochemical reduction of oxygen proceeding at the potential of −1.0 V (vs. Ag/AgCl) applied on the modified electrode. The process resulted in recharging of the electrode surface to the negative value due to the formation of the negative charge on the phenylboronic acid groups, thus resulting in the electrostatic repulsion of insulin‐FITC and stimulating its release from the electrode surface. The insulin release was characterized by fluorescence spectroscopy (using the FITC‐labeled insulin), by electrochemical measurements on an iridium oxide, IrO_x, electrode and by mass spectrometry. The graphene‐functionalized carbon fiber electrode demonstrated significant advantages in the signal‐stimulated insulin release comparing with the carbon fiber electrode without the graphene species.     

Density functional study of super cell N-doped (10,0) zigzag single-walled carbon nanotubes as CO sensor

N-doped SWCNT with different concentration of doped nitrogen atoms were investigated through density functional theory (DFT) calculations for detecting CO molecule. The CO molecule was adsorbed to different sites of the modified nanotubes and their geometric structures and electronic properties were investigated after full optimization. A significant change can be observed in adsorption energies and electronic properties of N-doped SWCNT after CO adsorption. By increasing the number of nitrogen atoms in each unit cell, these properties change more obviously. So these modified nanotubes can be used as CO sensors.     

Carbon Nanotubes Modified Graphite Electrodes for Monitoring of Biointeraction Between 6‐Thioguanine and DNA

In this present study, single‐walled carbon nanotubes (SWCNT) modified disposable pencil graphite electrodes (SWCNT‐PGEs) were developed for the electrochemical monitoring of anticancer drug, and its interaction with double stranded DNA (dsDNA). Under this aim, SWCNT‐PGEs were applied for the first time in the literature to analyse of 6‐Thioguanine (6‐TG), and also to investigate its interaction with DNA by voltammetric and impedimetric methods. The surface morphologies of PGE and SWCNT‐PGE were explored using scanning electron microscopy (SEM) and electrochemical characterization of unmodified/modified electrodes was performed by cyclic voltammetry (CV). Experimental parameters; such as, the concentration of 6‐TG and its interaction time with dsDNA were optimized by using differential pulse voltammetry (DPV). Additionally, the interaction of 6‐TG with dsDNA was studied in case of different interaction times by electrochemical impedance spectroscopy (EIS) in contrast to voltammetric results. The detection limit of 6‐TG was found to be 0.25 μM by SWCNT‐PGE.     

Facile Synthesis of Ag Nanocubes of 30 to 70 nm in Edge Length with CF3COOAg as a Precursor

This paper describes a new protocol to synthesize Ag nanocubes of 30 to 70 nm in edge length with the use of CF₃COOAg as a precursor to elemental silver. By adding a trace amount of NaSH and HCl to the polyol synthesis, Ag nanocubes were obtained with good quality, high reproducibility, and on a scale up to 0.19 g per batch for the 70 nm Ag nanocubes. The Ag nanocubes were found to grow in size at a controllable pace over the course of synthesis. The linear relationship between the edge length of the Ag nanocubes and the position of localized surface plasmon resonance (LSPR) peak provides a simple method for finely tuning and controlling the size of the Ag nanocubes by monitoring the UV/Vis spectra of the reaction at different times.     

Silver nanoparticles supported on ionic‐tagged magnetic hydroxyapatite as a highly efficient and reusable nanocatalyst for hydrogenation of nitroarenes in water

A novel chemically modified magnetic hydroxyapatite (MHAp) was prepared and used as support and stabilizer for the synthesis of silver nanoparticles. First, 1,4‐diazabicyclo[2.2.2]octane (DABCO) was successfully grafted onto the surface of MHAp, and then silver nanoparticles were homogeneously loaded on mesoporous MHAp‐DABCO (ionic‐tagged MHAp) nanocomposite by in situ chemical reduction of silver nitrate using sodium borohydride. The structure and properties of the resulting MHAp‐DABCO‐Ag nanocomposite were confirmed using various techniques. The catalytic activity of ionic‐tagged MHAp‐Ag nanocatalyst was investigated for the hydrogenation reaction of nitroarenes in aqueous media. The results reveal that the Ag‐containing inorganic–organic nanocomposite is highly efficient for the reduction of a wide range of aromatic nitro compounds under green conditions. The superparamagnetic nature of the nanocatalyst leads to its being readily removed from solution via application of a magnetic field, and it can be easily stored and reused.     

Visible‐light photocatalytic activity of Ag@MIL‐125(Ti) microspheres

Ag nanoparticle (NP)‐decorated MIL‐125(Ti) microspheres (Ag@MIL‐125(Ti)) were firstly fabricated via a facile hydrothermal and following photo‐reduction method. The photocatalysts were characterized using X‐ray diffraction, scanning and transmission electron microscopies, X‐ray photoelectron spectroscopy and UV–visible diffuse reflectance spectroscopy. The characterization results indicated that Ag NPs were dispersed on the surface of MIL‐125(Ti) microspheres, and the Ag NPs had a uniform diameter of about 40 nm. The composites exhibited excellent visible‐light absorption, due to the modification with the Ag NPs. The photocatalytic activity for the visible‐light‐promoted degradation of Rhodamine B was improved through the optimization of the amount of Ag loaded as a co‐catalyst, this amount being determined as 3 wt%. Additionally, studies performed using radical scavengers indicated that O₂^? and e^? served as the main reactive species. The catalyst can be reused at least five times without significant loss of its catalytic activity. Furthermore, a photocatalytic mechanism for degradation of organics over Ag@MIL‐125(Ti) is also proposed. Copyright © 2015 John Wiley & Sons, Ltd.