Electrochemical behaviour of Ni, Cu, Ag, Pt and glassy carbon electrodes in triethylamine-tris(hydrogen fluoride) medium

Voltammetric responses of Ni, Cu, Ag, Pt and glassy carbon (GC) electrodes in triethylamine-tris(hydrogen fluoride) medium in the anodic as well cathodic potential region were investigated. AAS as well as SEM measurements were also made to ascertain the dissolution rate and surface transformation due to fluoride film formation on the electrode surfaces. On Ni, bulk NiF₂ film growth occurs only around 4.0 V following a thin NiF₂ monolayer formation around 0 V. The NiF₂ film shows very little solubility in the medium. Monolayer and bulk CuF₂ phases are formed quite close to each other on Cu during anodic polarization. The anodically formed CuF₂ dissolves to the extent of 12% in this medium. AgF formation follows a different mechanism during the first and subsequent anodic sweeps. The effect of MeCN as well as water addition on the solubility and stability of these fluoride films are also reported. Glassy carbon and Pt electrodes are relatively inert in this medium. Anodic voltammetric responses for other reactive species could be observed only on Pt and GC electrodes. On the cathodic side, all the electrodes show inert behaviour. Electrochemical reduction of PhNO₂, for example, could be observed on all the electrodes. Electronic Publication     

Decorating Pt/C Nanoparticles with Ru by Wall‐Jet Configuration: The Role of Coverage Degree on the Catalyst Activity for Glycerol Electrooxidation

Here, we built Ru‐decorated Pt/C nanoparticles with different coverage degrees (θ_Ru) by wall‐jet configuration for the first time, and we investigated their catalytic properties towards glycerol electrooxidation in acidic medium. Moreover, we used the most active catalysts as the anode in electrolysis to produce carbonyl compounds. The use of an electrochemical cell in wall‐jet configuration allows for the controlling of electrodeposition through easily handling parameters; namely, the θ_Ru is controlled by changing the concentration of the metallic precursor, speed, and volume of injection onto a Pt/C‐modified glassy carbon electrode under applied potential. Excess of Ru on a Pt surface inhibits glycerol dissociative adsorption, which limits further electrooxidation; whereas low θ_Ru do not provide surface oxygen species to the anodic reaction. Hence, intermediates θ_Ru reveal active catalysts – namely, θ_Ru=0.42 shifts the onset potential 170 mV towards lower values and increases 1.65‐fold the current density at 0.5 V. The stability of this catalyst is also enhanced by maintaining a more constant current density during successive potential cycles in the presence of glycerol and by avoiding Ru leaching from the surface. The electrolysis on Ru‐decorated Pt/C is shown to lead the reaction towards formic acid (‘high oxidation state’), decreasing the amounts of glyceradehyde, glycolic acid, and dihydroxyacetone, as a result of the improved catalytic properties.     

Ambient Pressure X-ray Photoelectron Spectroscopy Study of Oxidation Phase Transitions on Cu(111) and Cu(110)

The surface structure effect on the oxidation of Cu has been investigated by performing ambient-pressure X-ray photoelectron spectroscopy (APXPS) on Cu(111) and Cu(110) surfaces under oxygen pressures ranging from 10⁻⁸ to 1 mbar and temperatures from 300 to 750 K. The APXPS results show a subsequential phase transition from chemisorbed O/Cu overlayer to Cu₂O and then to CuO on both surfaces. For a given temperature, the oxygen pressure needed to induce initial formation of Cu₂O on Cu(110) is about two orders of magnitude greater than that on Cu(111), which is in contrast with the facile formation of O/Cu overlayer on clean Cu(110). The depth profile measurements during the initial stage of Cu₂O formation indicate the distinct growth modes of Cu₂O on the two surface orientations. We attribute these prominent effects of surface structure to the disparities in the kinetic processes, such as the dissociation and surface/bulk diffusion over O/Cu overlayers. Our findings provide new insights into the kinetics-controlled process of Cu oxidation by oxygen.     

Enhanced Electrocatalytic Activity of Dual Template Based Pt/Cu‐zeolite A/Graphene for Methanol Electrooxidation

A novel Pt/Cu‐zeolite A/graphene based electrocatalyst was successfully prepared by chemical reduction method for methanol electrooxidation. Graphite oxide and Cu functionalized zeolite A were simultaneously reduced by NaBH₄ to prepare Cu‐zeolite A/graphene support which was used to deposit Pt nanoparticles. The nanostructure and composition of as‐prepared Pt/Cu‐zeolite A/graphene composites were characterized by X‐ray diffractometer, X‐ray fluorescence, Fourier transform infrared spectrometer and scanning electron microscopy. The electrocatalytic properties of Pt/Cu‐zeolite A/graphene modified electrode for methanol oxidation were investigated by cyclic voltammetry and chronoamperometry in 0.10 mol/L H₂SO₄ + 0.50 mol/L CH₃OH solution. Compared with Pt/zeolite A/graphene electrode and Pt/graphene electrode, Pt/Cu‐zeolite A/graphene based electrode exhibited obviously enhanced current and higher electrocatalytic activity for methanol electrooxidation. The increased electrocatalytic activity was attributed to the presence of zeolite A and reduced graphene oxide based dual template, which significantly increased the effective electrode surface and facilitated the diffusion of analytes into the electroactive catalyst.     

Electrochemical Designing of Au/Pt Core Shell Nanoparticles as Nanostructured Catalyst with Tunable Activity for Oxygen Reduction

Au/Pt core shell nanoparticles (NPs) have been prepared via a layer‐by‐layer growth of Pt layers on Au NPs using underpotential deposition (UPD) redox replacement technique. A single UPD Cu monolayer replacement with Pt(II) yielded a uniform Pt film on Au NPs, and the shell thickness can be tuned by controlling the number of UPD redox replacement cycles. Oxygen reduction reaction (ORR) in air‐saturated 0.1 M H₂SO₄ was used to investigate the electrocatalytic behavior of the as‐prepared core shell NPs. Cyclic voltammograms of ORR show that the peak potentials shift positively from 0.32 V to 0.48 V with the number of Pt layers increasing from one to five, suggesting the electrocatalytic activity increases with increasing the thickness of Pt shell. The increase in electrocatalytic activity may originate mostly from the large decrease of electronic influence of Au cores on surface Pt atoms. Rotating ring‐disk electrode voltammetry and rotating disk electrode voltammetry demonstrate that ORR is mainly a four‐electron reduction on the as‐prepared modified electrode with 5 Pt layers and first charge transfer is the rate‐determining step.     

Underpotential Deposition‐Induced Synthesis of Composition‐Tunable Pt?Cu Nanocrystals and Their Catalytic Properties

Pt? Cu alloy octahedral nanocrystals (NCs) have been synthesized successfully by using N,N‐dimethylformamide as both the solvent and the reducing agent in the presence of cetyltrimethylammonium chloride. Cu underpotential deposition (UPD) is found to play a key role in the formation of the Pt? Cu alloy NCs. The composition in the Pt? Cu alloy can be tuned by adjusting the ratio of metal precursors in solution. However, the Cu content in the Pt? Cu alloy NCs cannot exceed 50 %. Due to the fact that Cu precursor cannot be reduced to metallic copper and the Cu content cannot exceed 50 %, we achieved the formation of the Pt? Cu alloy by using Cu UPD on the Pt surface. In addition, the catalytic activities of Pt? Cu alloy NCs with different composition were investigated in electrocatalytic oxidation of formic acid. The results reveal that the catalytic performance is strongly dependent on Pt? Cu alloy composition. The sample of Pt₅₀Cu₅₀ exhibits excellent activity in electrocatalytic oxidation of formic acid.     

Surface composition of PdCuAu ternary alloys: a combined LEIS and XPS study

PdCuAu ternary alloy samples with different composition were synthesized on top of ZrO₂‐modified porous stainless steel disks by the sequential electroless deposition technique. The structure, morphology and bulk composition of the samples were characterized by X‐ray diffraction (XRD), scanning electron microscopy and energy dispersive X‐ray spectroscopy (EDX). Complete alloy formation with a pure fcc phase for the Pd₇₁Cu₂₆Au₃, Pd₇₀Cu₂₅Au₅ and Pd₆₇Cu₂₄Au₉ samples and a bcc structure for the Pd₆₂Cu₃₆Au₂ and Pd₆₀Cu₃₇Au₃ samples were obtained upon annealing at 500 °C for 120 h as revealed by XRD. A combination of low‐energy ion scattering (LEIS) and X‐ray photoelectron spectroscopy (XPS) was used to investigate the surface properties of the PdCuAu alloys. XPS results confirmed alloy formation under the annealing conditions. XPS analysis also revealed that the near‐surface regions of the alloys became enriched in Pd with respect to the bulk composition determined by EDX. In contrast, LEIS and angle‐resolved XPS analyses showed that the top‐most surface layers in all samples were copper‐rich compared with the bulk composition. This high Cu surface concentration could impart resistance to bulk sulfide formation to the PdCuAu alloy membranes. Copyright © 2015 John Wiley & Sons, Ltd.     

Structural Evolution of Pt,Au and Cu Anodes by Electrolysis up to Contact Glow Discharge Electrolysis in Alkaline Electrolytes**

Applying a voltage to metal electrodes in contact with aqueous electrolytes results in the electrolysis of water at voltages above the decomposition voltage and plasma formation in the electrolyte at much higher voltages referred to as contact glow discharge electrolysis (CGDE). While several studies explore parameters that lead to changes in the I–U characteristics in this voltage range, little is known about the evolution of the structural properties of the electrodes. Here we study this aspect on materials essential to electrocatalysis, namely Pt, Au, and Cu. The stationary I–U characteristics are almost identical for all electrodes. Detailed structural characterization by optical microscopy, scanning electron microscopy, and electrochemical approaches reveal that Pt is stable during electrolysis and CGDE, while Au and Cu exhibit a voltage-dependent oxide formation. More importantly, oxides are reduced when the Au and Cu electrodes are kept in the electrolysis solution after electrolysis. We suspect that H₂O₂ (formed during electrolysis) is responsible for the oxide reduction. The reduced oxides (which are also accessible via electrochemical reduction) form a porous film, representing a possible new class of materials in energy storage and conversion studies.     

On‐Surface Self‐Assembly of a C3‐Symmetric π‐Conjugated Molecule Family Studied by STM: Two‐Dimensional Nanoporous Frameworks

The on‐surface self‐assembled behavior of four C ₃‐symmetric π‐conjugated planar molecules ( Tp , T12 , T18 , and Ex ) has been investigated. These molecules are excellent building blocks for the construction of noncovalent organic frameworks in the bulk phase. Their hydrogen‐bonded 2D on‐surface self‐assemblies are observed under STM at the solid/liquid interface; these structures are very different to those in the bulk crystal. Upon combining the results of STM measurements and DFT calculations, the formation mechanism of different assemblies is revealed; in particular, the critical role of hydrogen bonding in the assemblies. This research provides us with not only a deep insight into the self‐assembled behavior of these novel functional molecules, but also a convenient approach toward the construction of 2D multiporous networks.     

Copper UPD on Selenium-Modified Polycrystalline Pt Electrode

Underpotential deposition of Cu onto an Se-modified smooth polycrystalline Pt electrode in an acidic CuSO₄ solution was investigated using a cyclic voltammetry. It was obtained that the specific voltammetric pattern of Cu UPD observed for a clean Pt electrode disappeared and a new current peak at potentials much closer to bulk Cu deposition was formed. This feature of a cyclic voltammogram is similar to that observed earlier for clean Pt electrode in acidic CuSO₄ solutions containing selenite and also to that described for S-modified Pt electrode in an additive-free CuSO₄ solution. The reasons for the difference in the voltammetric behavior of bare Pt and Se-modified Pt in the potential range characteristic of Cu UPD were considered. A model of Cu deposition taking place onto the free Pt sites at more positive potentials and onto the Se-covered ones at less positive potentials was discussed with closer scrutiny.     

Methane Activation by Platinum: Critical Role of Edge and Corner Sites of Metal Nanoparticles

Complete dehydrogenation of methane is studied on model Pt catalysts by means of state‐of‐the‐art DFT methods and by a combination of supersonic molecular beams with high‐resolution photoelectron spectroscopy. The DFT results predict that intermediate species like CH₃ and CH₂ are specially stabilized at sites located at particles edges and corners by an amount of 50–80 kJ mol^?1. This stabilization is caused by an enhanced activity of low‐coordinated sites accompanied by their special flexibility to accommodate adsorbates. The kinetics of the complete dehydrogenation of methane is substantially modified according to the reaction energy profiles when switching from Pt(111) extended surfaces to Pt nanoparticles. The CH₃ and CH₂ formation steps are endothermic on Pt(111) but markedly exothermic on Pt₇₉. An important decrease of the reaction barriers is observed in the latter case with values of approximately 60 kJ mol^?1 for first C? H bond scission and 40 kJ mol^?1 for methyl decomposition. DFT predictions are experimentally confirmed by methane decomposition on Pt nanoparticles supported on an ordered CeO₂ film on Cu(111). It is shown that CH₃ generated on the Pt nanoparticles undergoes spontaneous dehydrogenation at 100 K. This is in sharp contrast to previous results on Pt single‐crystal surfaces in which CH₃ was stable up to much higher temperatures. This result underlines the critical role of particle edge sites in methane activation and dehydrogenation.     

Polyelectrolyte brushes as efficient platform for synthesis of Cu and Pt bimetallic nanocrystals onto TiO2 nanowires

A Cu–Pt nanoparticle catalyst supported on TiO₂ nanowires (NWs) was prepared through regenerative counterion exchange–reduction using polyelectrolyte brush as template. Cationic polydimethyl aminoethyl methacrylate brushes were grafted onto TiO₂ NWs. Cu–Pt nanocrystals were produced by anionic counterions CuCl₄^2? and PtCl₆^2? bound with the polymer brush through in situ reduction with NaBH₄ of high density and low polydispersity. The as‐prepared TiO₂ NWs/polymer brush/Cu–Pt was characterized by Fourier transform infrared spectroscopy (FT‐IR spectrometry), X‐ray photoelectron spectroscopy, transmission electron microscopy, and UV–Vis adsorption spectrometry analyses. Results showed that the highly dispersed Cu and Pt nanoparticles were present on the surface of the TiO₂ NWs/polymer brush. The resultant TiO₂ NWs/polymer brush/Cu–Pt exhibited extremely high catalytic activity and reduced p‐nitrophenol at room temperature. Copyright © 2017 John Wiley & Sons, Ltd.     

Temperature effects on platinum single-crystal electrodes

This work reviews three different approaches for the study of temperature effects on the platinum single-crystal | solution interphase. First, the method of analysis of temperature-dependent voltammetric data with the help of a generalized isotherm is described and illustrated for the case of adsorbed hydrogen and OH species on Pt(111) in 0.1 M HClO₄. This method of analysis allows a detailed evaluation of the thermodynamic data of charge-transfer adsorbed species, namely, the standard molar Gibbs energy, enthalpy and entropy of adsorption and the magnitude of the lateral interaction between adsorbed species. However, a number of assumptions are involved in the application of a generalized isotherm, namely, the assumption of a Langmuirian configurational term and an arbitrary separation of capacitive and faradaic processes. The second approach described here overcomes these assumptions, since it employs Gibbs thermodynamic equations for interphaces to describe temperature effects on electrosorption processes including those in which charge-transfer is allowed. This approach allows evaluation of the entropy of formation of the interphase, being defined as the difference in entropy of the components of the interphase when they are forming it and when they are in the bulk phases. This method of analysis is illustrated through the evaluation of the entropy of formation of the interphase for Pt(111) in 0.1 M HClO₄. Finally, it is shown that temperature effects on interfacial processes can also be studied by means of the application of a fast temperature perturbation. This approach opens the possibility to separate the effect of temperature on the different components of the interphase. The fast temperature perturbation is usually achieved with short laser pulses, and hence the method is called the laser-induced temperature jump method. This approach is illustrated here for the case of Pt(111) in 1 mM HClO₄ + 0.1 M KClO₄, and it is shown that the corresponding laser-induced transients provide direct evidence on the reorientation of the interfacial water network.     

Influence of chemical equilibrium in introduced oxygen vacancies on resistive switching in epitaxial Pt-CeO<Subscript>2</Subscript> system

We investigate the introduction of oxygen vacancies by the interaction of Pt with CeO₂(111) (ceria) thin epitaxial film grown on Cu(111) and the influence of the vacancies on resistive switching behavior. For this purpose, we used X-ray photoelectron spectroscopy and conductive atomic force microscopy. We found out that after Pt deposition, the ceria film was partially reduced. By our estimation, the reduction occurs not only at the Pt/CeO₂ interface, but also on the surface of the ceria film which is not covered by Pt, after Pt deposition and annealing. A different distribution of oxygen vacancies in the film proves to have an influence on the resistance switching process of the film. Finally, the proper balance between the reduced and the unreduced species in order to obtain relatively stable repeatable resistance switch with clear resistance window is discussed.     

Epitaxial CeO2 thin films for a mechanism study of resistive random access memory (ReRAM)

A thin epitaxial CeO₂ film was grown on a Cu(111) single crystal in order to investigate the mechanism of resistive memory/switching devices with an ultimately thin high-k dielectric film. A small amount of Pt was deposited on the CeO₂ film and the Pt/CeO₂/Cu structure was characterized by conductive atomic force microscopy and X-ray photoelectron spectroscopy. It was found that the grown epitaxial CeO₂ film was fully oxidized, i.e., the valence of Ce atoms in the film was completely Ce⁴⁺. However, after the deposition of a small amount of Pt, it was revealed that Ce atoms were partially reduced to Ce³⁺ in full thickness of the film. The Pt/CeO₂/Cu structure did not show switching behavior in resistance. The observed reduction of CeO₂ film is considered to be responsible to the non-switching behavior. The thermodynamics of the reduction of the CeO₂ film and the kinetics of oxygen diffusion in the reduced CeO₂ film are discussed.     

Application of Statistical Lattice Models to the Analysis of Oscillatory and Autowave Processes in the Reaction of Carbon Monoxide Oxidation over Platinum and Palladium Surfaces

Statistical lattice models which imitate oscillatory and wave dynamics in the adsorbed layer during of carbon monoxide oxidation over Pt(100) and Pd(110) single crystals differing in the mechanism of autooscillation formation are compared. In the case of platinum, oscillations are due to phase transitions of the catalyst surface structure and surface reconstruction under the action of the reaction medium. In the case of palladium, the driving force of oscillations is phase transitions in the adsorbed layers on the catalyst surface, namely, the reversible formation of subsurface oxygen in the course of the reaction, which modifies the adsorption and catalytic properties of the surface. It is shown that, according to the proposed models, a change in the coverages (CO_ads O_ads) in the autooscillation regimes occurs via the formation of a surface wave whose front is characterized by the high concentration of catalytically active sites that provide the maximal rate of CO₂ molecule formation. Under certain conditions, the formation of various spatiotemporal structures is observed in simulation experiments.     

Real‐Time Atomic‐Scale Visualization of Reversible Copper Surface Activation during the CO Oxidation Reaction

By using in situ aberration‐corrected environmental transmission electron microscopy, for the first time at atomic level, the dynamic evolution of the Cu surface is captured during CO oxidation. Under reaction conditions, the Cu surface is activated, typically involving 2–3 atomic layers with the formation of a reversible metastable phase that only exists during catalytic reactions. The distinctive role of CO and O₂ in the surface activation is revealed, which features CO exposure to lead to surface roughening and consequently formation of low‐coordinated Cu atoms, while O₂ exposure induces a quasi‐crystalline CuOx phase. Supported by DFT calculations, it is shown that crystalline CuOx reversibly transforms into the amorphous phase, acting as an active species to facilitate the interaction of gas reactants and catalyzing CO oxidation.     

Solid state reactions in the platinum–mercury system

Thermogravimetry, Differential Scanning Calorimetry and other analytical techniques (Energy Dispersive X-ray Analysis; Scanning Electron Microscopy; Mapping Surface; X-ray Diffraction; Inductively Coupled Plasma Atomic Emission Spectroscopy and Cold Vapor Generation Atomic Absorption Spectroscopy) have been used to study the reaction of mercury with platinum foils. The results suggest that, when heated, the electrodeposited Hg film reacts with Pt to form intermetallic compounds each having a different stability, indicated by at least three mass loss steps. Intermetallic compounds such as PtHg₄, PtHg and PtHg₂ were characterized by XRD. These intermetallic compounds were the main products formed on the surface of the samples after partial removal of bulk mercury via thermal desorption. The Pt(Hg) solid solution formation caused great surface instability, attributed to the atomic size factor between Hg and Pt, facilitating the acid solution’s attack to the surface.     

Controlled dispersion of polystyrene‐capped Au nanoparticles in P3HT:PC61BM and consequences upon active layer nanostructure

Numerous recent publications detail higher absorption and photovoltaic performance within organic photovoltaic (OPV) devices which are loaded with Au or Ag nanoparticles to leverage the light management properties of the localized surface plasmon resonance (LSPR). This report details the impact upon film morphology and polymer/nanoparticle interactions caused by incorporation of polystyrene‐coated Au nanoparticles (Au/PS) into the P3HT:PC₆₁BM bulk heterojunction film. Nanostructural analysis by transmission electron microscopy and X‐ray scattering reveals tunable Au/PS particle assembly that depends upon the choice of casting solvent, polymer chain length, film drying time, and Au/PS particle loading density. This Au/PS particle assembly has implications on the spectral position of the Au nanoparticle LSPR, which shifts from 535 nm for individually dispersed particles in toluene to 650 nm for particles arranged in large clusters within the P3HT:PC₆₁BM matrix. These results suggest a critical impact from PS/P3HT phase separation, which causes controlled assembly of a separate Au/PS phase in the nanoparticle/OPV composite; controlled Au/PS phase formation provides a blueprint for designing AuNP/OPV hybrid films that impart tunable optical behavior and potentially improve photovoltaic performance. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 709–720     

Selective Amplification of CO Bond Hydrogenation on Pt/TiO2: Catalytic Reaction and Sum‐Frequency Generation Vibrational Spectroscopy Studies of Crotonaldehyde Hydrogenation

The hydrogenation of crotonaldehyde in the presence of supported platinum nanoparticles was used to determine how the interaction between the metal particles and their support can control catalytic performance. Using gas‐phase catalytic reaction studies and in situ sum‐frequency generation vibrational spectroscopy (SFG) to study Pt/TiO₂ and Pt/SiO₂ catalysts, a unique reaction pathway was identified for Pt/TiO₂, which selectively produces alcohol products. The catalytic and spectroscopic data obtained for the Pt/SiO₂ catalyst shows that SiO₂ has no active role in this reaction. SFG spectra obtained for the Pt/TiO₂ catalyst indicate the presence of a crotyl‐oxy surface intermediate. By adsorption through the aldehyde oxygen atom to an O‐vacancy site on the TiO₂ surface, the C?O bond of crotonaldehyde is activated, by charge transfer, for hydrogenation. This intermediate reacts with spillover H provided by the Pt to produce crotyl alcohol.