Partially reduced graphite oxide as an electrode material for electrochemical double-layer capacitors

Partially reduced graphite oxide was prepared from graphite oxide by using synthetic graphite as precursor. The reduction of graphite oxide with a layer distance of 0.57?nm resulted in a reduction of the layer distance depending on the degree of reduction. Simultaneously the amount of oxygen functionalities in the graphite oxide was reduced, which was corroborated by elemental analysis and EDX. The electrochemical activation of the partially reduced graphite oxide was investigated for tetraethylammonium tetrafluoroborate in acetonitrile and in propylene carbonate. The activation potential depends significantly on the degree of reduction, that is, on the graphene-layer distance and on the solvent used. The activation potential decreased with increasing layer distance for both positive and negative activation. The resulting capacitance after activation was found to be affected by the layer distance, the oxygen functionalities and the used electrolyte. For a layer distance of 0.43?nm and with acetonitrile as the solvent, a differential capacitance of 220?Fg(-1) was achieved for the discharge of the positive electrode near the open-circuit potential and 195?Fg(-1) in a symmetric full-cell assembly.     

Supercapacitor based on graphene and ionic liquid electrolyte

A new kind of supercapacitor by using chemical reduced graphene (CRG) as electrode material and ionic liquid with addition of acetonitrile as electrolyte is assembled and investigated. CRG materials with high surface area are prepared by chemical reduction of graphene oxide. The capacitive properties of the supercapacitor composed of the CRG and ionic liquid electrolyte are studied by electrical impedance spectroscopy, cyclic voltammetry and galvanostatic charge–discharge. With the combined advantages of graphene and ionic liquid, the supercapacitor shows perfect performance. The supercapacitor possesses wide cell voltage and good stability. The specific capacitance, energy density, and specific power density of the present supercapacitor are 132?Fg^??, 143.7?Wh?kg^??, and 2.8?kW?kg^??, respectively. The results demonstrate the potential application of electrical energy storage devices with high performance based on this new kind of supercapacitor.     

Supercapacitor based on graphene and ionic liquid electrolyte

A new kind of supercapacitor by using chemical reduced graphene (CRG) as electrode material and ionic liquid with addition of acetonitrile as electrolyte is assembled and investigated. CRG materials with high surface area are prepared by chemical reduction of graphene oxide. The capacitive properties of the supercapacitor composed of the CRG and ionic liquid electrolyte are studied by electrical impedance spectroscopy, cyclic voltammetry and galvanostatic charge–discharge. With the combined advantages of graphene and ionic liquid, the supercapacitor shows perfect performance. The supercapacitor possesses wide cell voltage and good stability. The specific capacitance, energy density, and specific power density of the present supercapacitor are 132 Fg⁻¹, 143.7 Wh kg⁻¹, and 2.8 kW kg⁻¹, respectively. The results demonstrate the potential application of electrical energy storage devices with high performance based on this new kind of supercapacitor.

     

Synthesis,characterizations, and electrochemical studies of ZnO/reduced graphene oxide nanohybrids for supercapacitor application

Herein the present article reports the fabrication of ZnO/reduced graphene oxide (ZnG) nanohybrid following a reduction-based process using a non-hazardous material, i.e., ascorbic acid. The morphology, structure, and bonding in the nanohybrid were analyzed using different techniques. Atomic force microscopy and scanning electron microscopy images show spherical particles of ZnO distributed over reduced graphene oxide (rGO). The X-ray diffraction analysis gives calculated values of crystallite size for ZnO as 15.62 nm. The successful incorporation of ZnO nanoparticles into rGO was confirmed using energy-dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy analyses. The electrochemical studies were performed using an electrolyte (0.5 M H₂SO₄). The calculated value of specific capacitance for the nanohybrid was 345 Fg^-1, which was found to be almost double as compared to that of rGO, which is having a value of only 190.5 Fg^-1 at the same scan rate. The nanohybrid also showed excellent capacitance retention after 1,000 cycles.     

Precise Tuning of Surface Composition and Electron‐Transfer Properties of Graphene Oxide Films through Electroreduction

Graphene materials are generally prepared from the exfoliation of graphite oxide (GO) to graphene oxide, followed by subsequent chemical or thermal reduction. These methods, although efficient in removing most of the oxygen functionalities from the GO material, lack control over the extent of the reduction process. We demonstrate here an electrochemical reduction procedure that not only allows for precise control of the reduction process to obtain a graphene material with a well‐defined C/O ratio in the range of 3 to 10, but also one that is able to tune the electrocatalytic properties of the reduced material. A method that is able to precisely control the amount and density of the oxygen functionalities on the graphene material as well as its electrochemical behaviour is very important for several applications such as electronics, bio‐composites and electrochemical devices.     

Electrochemical exfoliation and in situ carboxylic functionalization of graphite in non-fluoro ionic liquid for supercapacitor application

Simultaneous electrochemical generation and functionalization of nano-sized graphite from graphite had been carried out in a non-fluoroanion-based ionic liquid, namely, triethylmethylammonium methylsulfate (TEMAMS) containing water and acetonitrile (AN) in different weight ratios. The oxygen-based functional groups attached with the exfoliated material had been identified using Fourier transform infrared spectroscopy (FTIR), and morphological changes were characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). A symmetrical supercapacitor was fabricated using the exfoliated nano-sized graphite, and the influence of surface functionalities on its performance was investigated using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and galvanostatic charge–discharge cycles (CC). The highest specific capacitance (C _sp) value of 140 F g^?1 at 0.25 A g^?1 was obtained in 1.0 M H₂SO₄, followed by aqueous TEMAMS (125 F g^?1), TEMAMS/acetonitrile (115 F g^?1), and TEMAMS (106 F g^?1) at 0.10 A g^?1.     

Inherent Electrochemistry and Activation of Chemically Modified Graphenes for Electrochemical Applications

Graphene research is currently at the frontier of electrochemistry. Many different graphene‐based materials are employed by electrochemists as electrodes in sensing and in energy‐storage devices. Because the methods for their preparation are inherently different, graphene materials are expected to exhibit different electrochemical behaviors depending on the functionalities and density of defects present. Electrochemical treatment of these “chemically modified graphenes” (CMGs) represents an easy approach to alter surface functionalities and consequently tune the electrochemical performance. Herein, we report a preliminary electrochemical characterization of four common chemically modified graphenes, namely: graphene oxide, graphite oxide, chemically reduced graphene oxide, and thermally reduced graphene oxide. These CMGs were compared with graphite as a reference material. Cyclic voltammetry was used to ascertain the chemical functionalities present and to understand the potential ranges in which the materials were electroactive. Electrochemical treatment with either an oxidative or a reductive fixed potential were then carried out to activate these chemically modified graphenes. The effects of such electrochemical treatments on their electrocatalytic properties were then investigated by cyclic voltammetry in the presence of well‐known redox probes, such as [Fe(CN)₆]^4?/3?, Fe^3+/2+, [Ru(NH₃)₆]^2+/3+, and ascorbic acid. Thermally reduced graphene oxide exhibited the best electrochemical behavior amongst all of the CMGs, with the fastest rate of heterogeneous electron transfer (HET) and the lowest overpotentials. These findings will have far‐reaching consequences for the evaluation of different CMGs as electrode materials in electrochemical devices.     

Double Layer Impedance in Mixtures of Acetonitrile and Water

Double layer (DL) impedances were evaluated in mixed solutions of water and acetonitrile at various ratios in the polarized potential domain in order to find competitive orientation of the two solvent molecules on the platinum electrode. The DL capacitance at any ratio of the mixture shows the common power law of the ac‐frequency. The capacitance at molar fractions of water less than 0.2 increases linearly with the fraction, and reaches the value for aqueous solution. This variation indicates accumulation of water molecules on the electrode excluding acetonitrile molecules. It is modelled on the concept of the Langmuir‐type isotherm in which water and acetonitrile molecules have competitive interaction with the electrode. The experimental variations by the use of the isotherm yield the difference in the interaction energy, 6 kJ mol⁻¹. The accumulation of water in the DL is supported by the formation of the adsorbed layer by insoluble ferrocene.     

Preparation and electrochemical analysis of graphene/polyaniline composites prepared by aniline polymerization

Polyaniline (PANI)/graphene nanosheet (GNS) composites were prepared by a chemical oxidation polymerization. The morphology, structure, and crystallinity of the composites were examined by scanning electron microscopy, transition electron microscopy, and X-ray diffraction. Electrochemical properties were characterized by cyclic voltammetry in 1 M H₂SO₄ electrolyte. GNS are considered as supporting materials which can provide a large number of active sites. The PANI nanofibers with diameter of 50 nm were homogeneously coated on the surface of GNS. The PANI/GNS composites exhibited a better electrochemical performance than the pure individual components. The PANI/GNS composites showed the highest specific capacitance 923 Fg^?1 at 10 mVs^?1 compared to 465 Fg^?1 for pure PANI and 99 Fg^?1 for GNS.     

An Electrochemical Transducer Based on a Pentacene Double‐Gate Thin‐Film Transistor

We report an electrochemical transducer based on an organic double‐gate transistor. The bottom‐gate is given by a p‐doped silicon substrate, which is covered by 300 nm thermal oxide. A 20 nm pentacene film acts as the semiconducting layer, and a 50 nm tetratetracontane (TTC) alkane film is used as a top‐gate dielectric. An aqueous ionic solution acts as top‐gate. We record the transistor transfer characteristics by variation of the electrolyte potential via a Ag/AgCl electrode for various bottom‐gate settings. A change of the electrolyte potential results in a change of the transistor current and the characteristic behaviour of the device is in good agreement with the expected behaviour of a double‐gate transistor. The top‐gate capacitance of the alkane layer is as high as 2.6×10^?8 F cm^?2 determined by impedance measurements, indicating that TTC is a good choice as an organic top‐gate dielectric. The suitability of this transducer configuration for sensing in aqueous media is demonstrated by the detection of hexanoic acid and stearic acid molecules adsorbing to the alkane interface, respectively. We show that the transducer easily achieves a concentration sensitivity in the range of 100 nM.     

Comparison of electrochemical properties of two-component C60-Pd polymers formed under electrochemical conditions and by chemical synthesis

The electrochemical behavior of C₆₀-Pd polymer formed under electrochemical conditions and by the chemical synthesis was examined. In these polymers, fullerene moieties are covalently bonded to palladium atoms to form a polymeric network. Both materials deposited at the electrode surface show electrochemical activity at negative potentials due to the reduction of fullerene cage. Electrochemically formed thin polymeric films exhibit much more reversible voltammetric response in comparison to chemically synthesized polymers. The morphology and electrochemical behavior of chemically synthesized C₆₀-Pd polymer depend on the composition of grown solution. Chemical polymerization results in formation of large, ca. 50 μm, crystallic superficial structures that are composed of regular spherical particles with a diameter of 150 nm. The capacitance properties of C₆₀-Pd films were investigated by cyclic voltammetry and faradaic impedance spectroscopy. Specific capacitance of chemically formed films depends on the conditions of film formation. The best capacitance properties was obtained for films containing 1:3 fullerene to Pd molar ratio. For these films, specific capacitance of 35 Fg^?1 was obtained in acetonitrile containing (n-C₄H₉)₄NClO₄. This value is much lower in comparison to the specific capacitance of electrochemically formed C₆₀-Pd film.     

Symmetric electrochemical supercapacitor performance evaluation of N-doped graphene prepared via supercritical fluid processing

Here, the fast and shorter duration synthesis route was proposed for the production of N-doped graphene by supercritical fluid method involving ammonium oxalate as a source of nitrogen. Within the different proportions of graphene oxide and nitrogen source, the nitrogen-doped graphene formed from ammonium oxalate having nitrogen content of 3.3 wt% showed an enriched specific capacitance of 274 Fg^?1 at 1 A/g in 20% KOH electrolyte. The long-term stability results obtained from galvanostatic charge-discharge in ammonium oxalate-based N-doped graphene revealed that 90% specific capacitance retention was achieved up to 10,000 cycles at 10 A/g. To examine the device proficiency, a full cell was fabricated and the performance was evaluated in two different approaches. Among the different media in aqueous electrolytes, the fabricated symmetric supercapacitor has achieved a maximum specific capacitance value of 160 F/g at 1 A/g in alkaline medium (20% KOH solution). Between 20% KOH solution and 1 M NaClO₄ solution in acetonitrile, the fabricated symmetric supercapacitor exhibits an energy density of 26.5 Wh/kg as well as 5.5 Wh/kg in 1 M sodium perchlorate in acetonitrile solution and 20% KOH solution, respectively.     

KOH‐Activated Porous Carbons Derived from Chestnut Shell with Superior Capacitive Performance

Porous carbons (PC) were prepared from a waste biomass named chestnut shell via a two‐step method involving carbonization and KOH activation. The morphology, pore structure and surface chemical properties were investigated by scanning electron microscopy (SEM), N₂ sorption, Raman spectroscopy, X‐ray diffraction (XRD) and X‐ray photoelectron spectroscopy (XPS). The carbons have been evaluated as the electrode materials for supercapacitors by a two‐electrode system in 6 mol/L KOH electrolyte. Benefiting from the porous texture, high surface area and high oxygen content, the PCs derived from chestnut shell have exhibited high specific capacitance of 198.2 (PC‐1), 217.2 (PC‐2) and 238.2 F·g^?1 (PC‐3) at a current density of 0.1 A·g^?1, good rate capability of 55.7%, 56.6% and 54.9% in a range of 0.1–20 A·g^?1 and high energy density of 5.6, 6.1 and 6.7 Wh·kg^?1, respectively. This is believed to be due to electric double layer capacitance induced by the abundant micropores and extra pseudo‐capacitance generated by oxygen‐containing groups. At a power density of 9000 Wh·kg^?1, the energy density is 3.1, 3.5 and 3.7 Wh·kg^?1 for PC‐1, PC‐2 and PC‐3, respectively, demonstrating the potential of the carbons derived from chestnut shells in energy storage devices.     

An Electrochemical Route to Quantitative Oxidation of Graphene Frameworks with Controllable C/O Ratios and Added Pseudocapacitances

We report an electrochemical oxidation route to tunable C/O ratios in the graphene framework, creating enhanced pseudocapacitance with increasing oxygen content. Controlled surface functionalities on graphene enable a high specific capacitance and negligible electric conductivity loss. A specific capacitance of up to 279 F g^?1 was achieved for the functionalized graphene at a discharge current of 1 A g^?1 in 1 M H₂SO₄ electrolyte; this capacitance remained as high as 152 F g^?1 at 100 A g^?1. These values are much higher than those of non‐oxidized graphene. These excellent performances of the functionalized graphene signify the importance of precise control of the surface chemistry of graphene‐based materials.     

Electrochemical reduction of graphene oxide and its electrochemical capacitive performance

A convenient method for the production of graphene is developed using the electrochemical reduction of graphite oxide (GO) in solution without assembling it onto the electrode. The samples were examined by X-ray diffraction, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and Raman spectroscopy. The results show that the number of oxygen functional groups can be significantly decreased. The electrochemical capacitance of the prepared graphene after 8 h of reduction is 158.5 F g^?1 at 0.5 A g^?1, much higher than that of GO and carbon nanotubes. The mechanism for this reaction is also proposed in this paper.     

The double layer at the interface between two immiscible electrolyte solutions: Part II. Structure of the water/nitrobenzene interface in the presence of 1:1 and 2:2 electrolytes

From fast galvanostatic pulse measurements at 25°C the capacitance of the water/nitrobenzene interface was evaluated as a function of the interfacial potential difference Δ_o^w? for systems consisting of NaBr, LiCl or MgSO₄ in water and tetrabutylammonium tetraphenylborate, tetraphenylarsonium tetraphenylborate or tetraphenylarsonium dicarbollylcobaltate in nitrobenzene. The modified Verwey—Niessen model, in which an inner layer of solvent molecules separates two space-charge regions (the diffuse double layer), describes the structure of the water/nitrobenzene interface well at electrolyte concentrations above ca. 0.02 mol dm^?3, provided that the ions are allowed to penetrate into the inner layer over some distance. For all the systems studied the zero-charge potential difference was found at Δ^w_o?_pzc ≈ 0 on the basis of the standard potential difference Δ^w_o?⁰_TMA + = 0.035 V for tetramethylammonium cation which was used as a reference ion. At zero surface charge a comparison was made with the theoretical capacitance calculated using the mean spherical approximation for a model consisting of two ion and dipole mixtures facing each other. The effect of ion penetration on the interfacial capacitance was estimated from the solution of the linearized Poisson-Boltzmann equation for a triple dielectric model with a continuous distribution of the point ions. The concentration-independent inner layer potential difference and capacitance can only be inferred from the capacitance data if the ion size effect is taken into account. A non-iterative procedure based on the hypernetted-chain equation was used for the evaluation of the potential drop across the diffuse double layer. The extend of the penetration into the inner layer appears to be a function of ion solvation, e.g. the more hydrated ion the less extensive ion penetration is likely.     

On Oxygen‐Containing Groups in Chemically Modified Graphenes

Reduced graphenes (belonging to the class of chemically modified graphenes, CMG) are one of the most investigated and utilized materials in current research. Oxygen functionalities on the CMG surfaces have dramatic influences on material properties. Interestingly, these functionalities are rarely comprehensively characterized. Herein, the four most commonly used CMGs, mainly electrochemically reduced graphene oxide (ER‐GO), thermally reduced graphene oxide (TR‐GO), and the corresponding starting materials, that is, graphene oxide and graphite oxide, were comprehensively characterized by a wide variety of methods, such as high‐resolution X‐ray photoelectron spectroscopy, electrochemical impedance spectroscopy, UV/Vis spectroscopy, transmission electron microscopy (TEM), and voltammetry, to establish connections between the structures of these materials that carry different oxygen functionalities and their electrochemical behaviors. This was followed by the quantification of the negatively charged oxygen‐containing groups (OCGs) by UV/Vis spectroscopy and of the electrochemically reducible OCGs by voltammetry. Lastly, a biofunctionalization with gold nanoparticle (AuNP)‐modified DNA sequences was performed by the formation of covalent bonds with the carboxylic groups (? COOH) on the CMG surfaces. There was an evident predominance of functionalizable ? COOH groups on the ER‐GO surface, as confirmed by a higher amount of Au detected both with differential‐pulse voltammetry and impedance spectroscopy, coupled with visualization by TEM. We exploited the DNA–Au bioconjugates as highly specific stains to localize and visualize the positions of carboxylic groups. Our findings are very important to clearly identify the presence, nature, and distribution of oxygen functionalities on different chemically modified graphenes.     

Ultrathin Carbon Nanoparticle Composite Film Electrodes: Distinguishing Dopamine and Ascorbate

Ultrathin carbon nanoparticle–poly(diallyldimethylammonium chloride) films (CNP‐PDDAC films) are formed on tin‐doped indium oxide (ITO) electrodes in a layer‐by‐layer electrostatic deposition process employing 9–18 nm diameter carbon particles. Transparent and strongly adhering films of high electrical conductivity are formed and characterized in terms of their electrochemical reactivity. When immersed in aqueous 0.1 M phosphate buffer pH 7, each layer of CNP‐PDDAC (of ca. 5–6 nm average thickness) is adding an interfacial capacitance of ca. 10 μF cm^?2. Absorption into the CNP–PDDAC nanocomposite film is dominated by the sites in the PDDAC cationomer and therefore anionic molecules such as indigo carmine are strongly bound and retained within the film (cationic binding sites per layer ca. 150 pmol cm^?2). In contrast, cationic redox systems such as ferrocenylmethyltrimethyl‐ammonium⁺ fail to bind. For solution phase redox systems such as hydroquinone, the rate of electron transfer is dramatically affected by the CNP‐PDDAC film and switched from completely irreversible to highly reversible even with a single layer of carbon nanoparticles. For the mixed redox system ascorbate–dopamine in 0.1 M phosphate buffer pH 7 cyclic voltammograms suggest a rapid and selective temporary poisoning process which causes the ascorbate oxidation to be suppressed in the second potential cycle. This effect is exploited for the detection of micromolar concentrations of dopamine in the presence of millimolar ascorbate.     

Non‐Covalent Functionalization of Graphene with Bisphenol A for High‐Performance Supercapacitors

The reduced graphene oxide (RGO)/bisphenol A (BPA) composites were prepared by an adsorption‐reduction method. The composites are characterized by X‐ray diffraction (XRD), UV‐vis, thermogravimetric (TG) analysis, field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM). The results confirm that BPA is adsorbed on the basal plane of RGO by π‐π stacking interaction. Furthermore, the electrochemical behaviors were evaluated by cyclic voltammetry, galvanostatic charge/discharge techniques and electrochemical impedance spectroscopy (EIS). The results show that the RGO/BPA nanocomposites exhibit ultrahigh specific capacitance of 466 F·g^?1 at a current density of 1 A·g^?1, excellent rate capability (more than 81% retention at 10 A·g^?1 relative to 1 A·g^?1) and superior cycling stability (90% capacitance decay after 4000 cycles). Consequently, the RGO/BPA nanocomposites can be regarded as promising electrode materials for supercapacitor applications.     

Manganese Oxide/Graphene Aerogel Composites as an Outstanding Supercapacitor Electrode Material

Graphene aerogels (GA), prepared with an organic sol–gel process, possessing a high specific surface area of 793 m² g^?1, a high pore volume of 3 cm³ g^?1, and a large average pore size of 17 nm, were applied as a support for manganese oxide for supercapacitor applications. The manganese oxide was electrochemically deposited into the highly porous GA to form MnO₂/GA composites. The composites, at a high manganese oxide loading of 61 wt. %, exhibited a high specific capacitance of 410 F g^?1 at 2 mV s^?1. More importantly, the high rate specific capacitances measured at 1000 mV s^?1 for these composites were two‐fold higher than those obtained with samples prepared in the absence of the GA support. The specific capacitance retention ratio, based on the specific capacitance obtained at 25 mV s^?1, was maintained high, at 85 %, even at the high scan rate of 1000 mV s^?1, in contrast with the significantly lower value of 67 % for the plain manganese oxide sample. For the cycling stability, the specific capacitance of the composite electrode decayed by only 5 % after 50,000 cycles at 1000 mV s^?1. The success of this MnO₂/GA composite may be attributed to the structural advantages of high specific surface areas, high pore volumes, large pore sizes, and three‐dimensionally well‐connected network of the GA support. These structural advantages made possible the high mass loading of the active material, manganese oxide, large amounts of electroactive surfaces for the superficial redox events, fast mass‐transfer within the porous structure, and well‐connected conductive paths for the involved charge transport.