Isolation of tetracyclines in milk using a solid-phase extracting column and water eluent

An isolating method using a solid-phase extraction (SPE) ISOLUTE® C8 endcapped syringe-column for routine monitoring of residual tetracyclines (TCs) (oxytetracycline (OTC), tetracycline (TC), chlortetracycline (CTC), and doxycycline (DC)) in cow's milk is presented. In the simplest and most environmentally harmless method, milk samples could be applied directly to the SPE column, following which all TCs were eluted with water. No organic solvents were used at all. The purified sample was injected into a high-performance liquid chromatography (HPLC) with a photo-diode array detector (PDAD). For the HPLC determination/identification, a LiChrospher® 100 RP-8 endcapped column and a mobile phase of acetonitrile −7% (v v⁻¹) acetic acid solution (in water) (35:65, v v⁻¹) with a PDAD was used. The total time required for the analysis of one sample was <40 min. Average recoveries (spiked 0.1-1.0 μg ml⁻¹ each drug) and their standard deviations were >80 and <5%, respectively.     

A dynamic liquid-liquid interfacial pressure detector for the rapid analysis of surfactants in a flowing organic liquid

Design and development of a dynamic interfacial pressure detector (DIPD) is reported. The DIPD measures the differential pressure as a function of time across the liquid-liquid interface of organic liquid drops (i.e., n-hexane) that repeatedly grow in water at the end of a capillary tip. Using a calibration technique based on the Young-Laplace equation, the differential pressure signal is converted, in real-time, to a relative interfacial pressure. This allows the DIPD to monitor the interfacial tension of surface active species at liquid-liquid interfaces in flow-based analytical techniques, such as flow injection analysis (FIA), sequential injection analysis (SIA) and high performance liquid chromatography (HPLC). The DIPD is similar in principle to the dynamic surface tension detector (DSTD), which monitors the surface tension at the air-liquid interface. In this report, the interfacial pressure at the hexane-water interface was monitored as analytes in the hexane phase diffused to and arranged at the hexane-water interface. The DIPD was combined with FIA to analytically measure the interfacial properties of cholesterol and Brij^®30 at the hexane-water interface. Results show that both cholesterol and Brij^®30 exhibit a dynamic interfacial pressure signal during hexane drop growth. A calibration curve demonstrates that the relative interfacial pressure of cholesterol in hexane increases as the cholesterol concentration increases from 100 to 10,000 μg ml⁻¹. An example of the utility of the DIPD as a selective detector for a chromatographic separation of interface-active species is also presented in the analysis of cholesterol in egg yolk by normal-phase HPLC-DIPD.     

Analysis of fenvalerate in its formulations and environmental samples using spectrophotometry

Two rapid, simple, sensitive, and nonextractive spectrophotometric methods were described for the determination of fenvalerate (syntheitic pyrethroid) in its formulations, water and grain samples. The methods are based on the hydrolysis of fenvalerate with methanolic NaOH to form 3-phenoxybenzaldehyde. The resultant aldehyde group was condensed with 4-aminoantipyrine in the basic medium to form a red product having λ_max at 489 nm or condensed with4,4′-methylene-bis-m-nitroaniline to form a plae red product with an absorption maximum of 513 nm. Beer’s law was obeyed over the range 0.6–10 μg/mL (molar absorptivity 2.184 × 10⁴ L/mol cm) for 4-aminoantityrine and over the range of 1–12 μg/mL (molar absorptivity 4.162 × 10⁴ L/mol cm) for 4,4′-methylene-bis-m-nitroaniline. The formations of color derivatives with the reagents are instantaneous and stable for 40 and 32 h, respectively. The methods were rapid, simple, sensitive, and free from nontarget species. The proposed methods have been applied to the determination of fenvalerate in its formulations and environmental samples. The text was submitted by the authors in English.     

Validation of a direct non-destructive quantitative analysis of amiodarone hydrochloride in Angoron formulations using FT-Raman spectroscopy

Raman spectroscopy was applied for the direct non-destructive analysis of amiodarone hydrochloride (ADH), the active ingredient of the liquid formulation Angoron^®. The FT-Raman spectra were obtained through the un-broken as-received ampoules of Angoron^®. Using the most intense vibration of the active pharmaceutical ingredient (API) at 1568 cm⁻¹, a calibration model, based on solutions with known concentrations, was developed. The model was applied to the Raman spectra recorded from three as-purchased commercial formulations of Angoron^® having nominal strength of 50 mg ml⁻¹ ADH. The average value of the API in these samples was found to be 48.56 ± 0.64 mg ml⁻¹ while the detection limit of the proposed technique was found to be 2.11 mg ml⁻¹. The results were compared to those obtained from the application of HPLC using the methodology described in the European Pharmacopoeia and found to be in excellent agreement. The proposed analytical methodology was also validated by evaluating the linearity of the calibration line as well as its accuracy and precision. The main advantage of Raman spectroscopy over HPLC method during routine analysis is that it is considerably faster and no solvent consuming. Furthermore, Raman spectroscopy is non-destructive for the sample. However, the detection limit for Raman spectroscopy is much higher than the corresponding for the HPLC methodology.     

Part two: Analytical optimisation of a procedure for lead detection in milk by means of bismuth-modified screen-printed electrodes

This work reports the optimisation of a new analytical method for lead ion detection in milk; the electrochemical detection scheme is based on the method that was described in Part I [1]. It features the use of a disposable, environmentally friendly bismuth film electrode to replace the traditionally used (toxic) mercury one while here we report an arduous development of sample treatment so that the simple device can be applied as a screening tool in many settings. For this purpose, a milk pre-treatment procedure by means of wet digestion with HCl, HClO₄, and H₂O₂ combined with an ultrasonic treatment was developed. The detection of lead ions in treated milk was then carried out using a disposable screen-printed electrode modified with Nafion^® and an “in situ” bismuth film, with the analysis being performed in anodic stripping voltammetry mode. The analytical method developed allows the detection of milk contaminated with lead ions at a concentration of 20 μg Kg⁻¹ (legal limit) and it can be proposed as a screening method for routine analysis of lead ions in milk with the advantage of employing inexpensive and portable instrumentation. Moreover, dedicated software supported by a portable instrument introduces procedures that are essential to avoid distortion from ambient lead contamination and also makes it possible for an unskilled operator to carry out each step of the analysis.     

Evaluation of novel amylose and cellulose-based chiral stationary phases for the stereoisomer separation of flavanones by means of nano-liquid chromatography

Three polysaccharide-based chiral stationary phases, Sepapak^® 1, Sepapak^® 2 and Sepapak^® 3 have been evaluated in the present work for the stereoisomer separation of a group of 12 flavonoids including flavanones (flavanone, 4′-methoxyflavanone, 6-methoxyflavanone, 7-methoxyflavanone, 2′-hydroxyflavanone, 4′-hydroxyflavanone, 6-hydroxyflavanone, 7-hydroxyflavanone, hesperetin, naringenin) and flavanone glycosides (hesperidin, naringin) by nano-liquid chromatography (nano-LC). The behaviour of these chiral stationary phases (CSPs) towards the selected compounds was studied in capillary columns (100 μm internal diameter (i.d.)) packed with the above mentioned CSPs using polar organic, reversed and normal elution modes. The influence of nature and composition of the mobile phase in terms of concentration and type of organic modifier, buffer type and water content (reversed phase elution mode) on the enantioresolution (R_s), retention factor (k) and enantioselectivity (α) was evaluated. Sepapak^® 3 showed the best chromatographic results in terms of enantioresolution, enantioselectivity and short analysis time, employing a polar organic phase mode. A mixture of methanol/isopropanol (20/80, v/v) as mobile phase enabled the chiral separation of eight flavanones with enantioresolution factor (R_s) in the range 1.15–4.18. The same analytes were also resolved employing reversed and normal phase modes with mixtures of methanol/water and hexane/ethanol at different ratios as mobile phases, respectively. Loss in resolution for some compounds, broaden peaks and longer analysis times were observed with these last two chromatographic elution modes.     

Synthesis and chromatographic resolution of conformationally constrained analogues of homotaurine

The first series of conformationally constrained analogues of homotaurine is reported. The partial constriction of the skeleton was realized through the insertion of a cyclopropyl ring, between the α,β- and β,γ-positions, thus affording, respectively, trans- and cis-2-aminomethylcyclopropane-1-sulfonic acids and trans- and cis-(2-aminocyclopropyl)methanesulfonic acids. The resolution of all four racemic mixtures was accomplished using HPLC system carrying the polysaccharide-based Chiralpak^® IB^® column as the chiral stationary phase. The coupling with an ‘Evaporative Light Scattering Detector (ELSD)’ has been particularly valuable during the chromatographic study.     

Gas-liquid chromatographic determination of fenvalerate on woolen cloth

A method is described for the determination of fenvalerate (cyano(3-phenoxyphenyl)methyl 4-chloro-α-(1-methylethyl)-benzeneacetate) residues on woolen cloth. The fenvalerate was Soxhlet-extracted from the treated fabric with acetone for four hours at a reflux rate of six solvent exchanges per hour. The fenvalerate residue was determined by gas-liquid chromatography with a flame ionization detector. The results were quantitated by comparing integrator counts obtained from extracts of treated samples with those obtained from known standards. The method was sensitive to 0.00054% fenvalerate by weight. Recoveries from fabric treated with 0.00054% to 0.215% averaged 94.8%. The response of the detector was linear over a 400-fold range of fenvalerate concentrations.     

Capacitive chemical sensor for fenvalerate assay based on electropolymerized molecularly imprinted polymer as the sensitive layer

A capacitive chemical sensor for fenvalerate is reported. By using ac impedance measurements the sensor has been based on the decrease in capacitance caused by the analyte used as the template in the formulation of an electropolymerized molecularly imprinted polymer as receptor layer. Improvement of the insulating properties of the sensor was investigated in detail. The capacitive sensor was prepared by a deposition of a self-assembled monolayer of 2-mercaptobenzimidazole (2-MBI) before electropolymerization of 2-MBI and subsequent treatment with n-dodecanethiol to eliminate pinholes and defects in the polymerized 2-MBI film. From the calibration curve concentrations of fenvalerate up to 9 g mL^–1 could be detected with a linear determination range up to 5 g mL^–1 and a detection limit of 0.36 g mL^–1. No significant interference was observed from common pyrethroid insecticides.     

Matrix diversion methods for improved analysis of perchlorate by suppressed ion chromatography and conductivity detection

Two inline matrix diversion methods were developed for the sensitive analysis of perchlorate in a matrix comprising up to 1000 mg l⁻¹ of chloride, sulfate and bicarbonate ions using suppressed ion chromatography and conductivity detection. The first method used a cryptand C1 concentrator column, which exhibited a high selectivity for perchlorate ion over the other matrix anions. After retaining the sample anions in a concentrator column derivatized with a crytpand phase, a rinse step was implemented with a weak base to divert the matrix ions to waste while selectively retaining perchlorate in the concentrator column for subsequent analysis. The analysis was done using a 2 mm IonPac^® AS16 or 2 mm IonPac^® AS20 separator column. The second method was a two-dimensional matrix diversion method with a focus on improving the detection sensitivity. The first dimension was used to achieve some resolution of the matrix ions from perchlorate. The perchlorate ion was then diverted into a concentrator column for subsequent analysis in the second dimension. By pursuing analysis using a 4 mm IonPac^® AS16 or IonPac^® AS20 column in the first dimension and subsequently pursuing analysis using a 2 mm IonPac^® AS16 or IonPac^® AS20 column format, excellent sensitivities were achieved when the first and second dimensions were operated at the same linear flow velocity (cm min⁻¹). While sensitive detection of perchlorate in the low μg l⁻¹ regime was achieved by the above methods in the presence of matrix ions, superior recovery for perchlorate was demonstrated under a variety of matrix concentrations by the second method.     

Characterization of new types of stationary phases for fast and ultra-fast liquid chromatography by signal processing based on AutoCovariance Function: A case study of application to Passiflora incarnata L. extract separations

In this study, a comparative investigation was performed of HPLC Ascentis^® (2.7 μm particles) columns based on fused-core particle technology and Acquity^® (1.7 μm particles) columns requiring UPLC instruments, in comparison with Chromolith™ RP-18e columns. The study was carried out on mother and vegetal tinctures of Passiflora incarnata L. on one single or two coupled columns. The fundamental attributions of the chromatographic profiles are evaluated using a chemometric procedure, based on the AutoCovariance Function (ACVF). Different chromatographic systems are compared in terms of their separation parameters, i.e., number of total chemical components (m_tot), separation efficiency (σ), peak capacity (n_c), overlap degree of peaks and peak purity. The obtained results show the improvements achieved by HPLC columns with narrow size particles in terms of total analysis time and chromatographic efficiency: comparable performance are achieved by Ascentis^® (2.7 μm particle) column and Acquity^® (1.7 μm particle) column requiring UPLC instruments. The ACVF plot is proposed as a simplified tool describing the chromatographic fingerprint to be used for evaluating and comparing chemical composition of plant extracts by using the parameters D% – relative abundance of the deterministic component – and c_EACF – similarity index computed on ACVF.     

A novel application of Onyx™ monolithic column for simultaneous determination of salicylic acid and triamcinolone acetonide by sequential injection chromatography

A novel and fast simultaneous determination of triamcinolone acetonide (TCA) and salicylic acid (SA) in topical pharmaceutical formulations by sequential injection chromatography (SIC) as an alternative to classical high performance liquid chromatography (HPLC) has been developed. A recently introduced Onyx™ monolithic C18 (50 mm × 4.6 mm, Phenomenex^®) with 5 mm monolithic precolumn were used for the first time for creating sequential injection chromatography system based on a FIAlab^® 3000 with a six-port selection valve and 5.0 mL syringe pump in study. The mobile phase used was acetonitrile/water (35:65, v/v), pH 3.3 adjusted with acetic acid at flow rate 0.9 mL min⁻¹. UV detection provided by fibre-optic DAD detector was set up at 240 nm. Propylparaben was chosen as suitable internal standard (IS). There is only simple pre-adjustment of the sample of topical solution (dilution with mobile phase) so the analysis is not uselessly elongated. Parameters of the method showed good linearity in wide range, correlation coefficient >0.999; system precision (relative standard deviation, R.S.D.) in the range 0.45-1.95% at three different concentration levels, detection limits (3σ) 1.00 μg mL⁻¹ (salicylic acid), 0.66 μg mL⁻¹ (triamcinolone acetonide) and 0.33 μg mL⁻¹ (propylparaben) and recovery from the pharmaceutical preparations in the range 97.50-98.94%. The chromatographic resolution between peaks of compounds was more than 4.5 and analysis time was 5.1 min under the optimal conditions. The advantages of sequential injection chromatography against classical HPLC are discussed and showing that SIC can be a method of option in many cases.     

Mercury analysis: a special example of species analysis

Summary Mercury species analysis requires the determination of numerous different compounds with very different behaviour regarding environment and toxicity. For these differing species several new and more sensitive analytical methods have been developed and tested. Mercury species cannot be detected directly in most cases, and are normally derivatized by different agents and determined by different detector systems. In a new HPLC method with photometric detection more than 10 different organomercurials could be analysed as their thio-ethanol complexes. By alkylation of mercury compounds they can be separated by GC and analysed with an AAS or AFS as detector. Volatile organic species of Hg can be separated on Carbotrap^®, where Hg⁰ is not adsorbed, and analysed thereafter. With atomic fluorescence the detection limit for Hg⁰ measurement is improved significantly when compared with the widely used atomic absorption method. Results obtained with this new method are shown and discussed. Future developments for species analysis are outlined; not only to analyse the covalent metal — carbon/oxygen compounds — primary species-analysis — but also compounds with ionic or complex bonding: secondary species-analysis. With these developments, prediction of species behaviour in the environment, including toxicity assessment and decontamination proposals, should be made possible.     

Differentiation of organically and conventionally produced milk by stable isotope and fatty acid analysis

Increasing sales of organic milk mean intensified tests for authenticity are required. In addition to comprehensive documentation, analytical methods to identify organic milk, and thus to differentiate it from conventional milk, are needed for consumer protection. Because the composition of milk is fundamentally dependent on the feeding of the cows, thirty-five samples from both production systems in Germany, including farm and retail milk, were collected within 12 months, to reflect seasonal variation, and appropriate properties were analysed. Fatty acid analysis enabled organic and conventional milk to be completely distinguished, because of the higher α-linolenic acid (C18:3ω3) and eicosapentaenoic acid (C20:5ω3) content of the former. Organic milk fat contained at least 0.56% C18:3ω3 whereas the maximum in conventional milk was 0.53%. Because of the parallel seasonal course of the C18:3ω3 content of organic and conventional retail samples, however, time-resolved comparison at the five sampling dates resulted in a clearer difference of 0.34 ± 0.06% on average. Analysis of stable carbon isotopes (δ¹³C) also enabled complete distinction of both types of milk; this can be explained by the different amounts of maize in the feed. For conventional milk fat δ¹³C values were −26.6‰ or higher whereas for organic milk fat values were always lower, with a maximum of −28.0‰. The time-resolved average difference was 4.5 ± 1.0‰. A strong negative correlation (r = −0.92) was found between C18:3ω3 and δ¹³C. Analysis of a larger number of samples is required to check the preliminary variation ranges obtained in this pilot study and, probably, to adjust the limits. Stable isotopes of nitrogen (δ¹⁵N) or sulfur (δ³⁴S) did not enable assignment of the origin of the milk; in cases of ambiguity, however, some trends observed might be useful in combination with other properties. Figure Correlation (r = −0.92) between δ¹³C value and C18:3ω3 content of milk fat from different production systems     

Determination of pesticides fenoxycarb and permethrin by sequential injection chromatography using miniaturized monolithic column

Sequential injection chromatography system equipped with miniaturized 10 mm monolithic column was used for fast simultaneous determination of two pesticides—fenoxycarb (FC) and permethrin (PM). The system was composed of a commercial sequential injection analysis (SIA) system (FIAlab^® 3000, 6-port selection valve and 5.0 mL syringe pump), commercially available column Chromolith™ RP-18e (10 mm × 4.6 mm i.d.) (Merck^®, Germany) and CCD UV-vis detector (USB 2000, Ocean-optics) with 1.0 cm Z-flow cell, absorbance was monitored at 225 nm. The mobile phase used for analysis was acetonitrile/water (60:40, v/v), flow rates were 0.6 mL min⁻¹ for elution of fenoxycarb and 1.2 mL min⁻¹ for elution of permethrin. For each analysis 4.8 mL of mobile phase was used. The chromatographic resolution between both compounds was >8 and analysis time was <6.5 min under the optimal conditions. Limits of detection were determined at 2.0 μg mL⁻¹ for fenoxycarb and 1.0 μg mL⁻¹ for permethrin. Samples were prepared by diluting with mobile phase and injected volume was 10 μL for each analysis. Developed method was applied to analysis of both pesticides in veterinary pharmaceutical foams and sprays ARPALIT^® Neo (Aveflor, Czech Republic). SIC method was compared with validated method (HPLC, reverse phase 100 mm monolithic column, gradient elution).     

A novel high selectivity chemiluminescence sensor for fenvalerate based on double-sided hollow molecularly imprinted materials

Novel fenvalerate double-sided hollow molecularly imprinted microspheres (fenvalerate-DHMIMs) were fabricated by in situ polymerization with the help of mesoporous silica microspheres (MSMs) in this paper for the very first time. Scanning electron microscope was employed to characterize the surface morphology of the fenvalerate-DHMIMs. Taking advantage of the quenching effect of fenvalerate on the luminol-H(2)O(2)-NaOH chemiluminescence system, a new model was established to determine fenvalerate by a highly selective flow injection chemiluminescence method. The traditional flow-through cell was replaced by a novel Y-shaped column. The chemiluminescence intensity was linear with fenvalerate concentration over the range of 5.0 × 10(-8) to 2.0 × 10(-5) g mL(-1) and the detection limit was 2.2 × 10(-8) g mL(-1). The relative standard deviation (RSD) for the determination of 2.0 × 10(-6) g mL(-1) fenvalerate was 1.4% (n = 11). The proposed method was applied to the determination of fenvalerate in real samples with satisfactory results.     

Preparative enantioseparation of (±)-N-(3,4-cis-3-decyl-1,2,3,4-tetrahydrophenanthren-4-yl)-3,5-dinitrobenzamide by centrifugal partition chromatography

The racemic compound (±)-N-(3,4-cis-3-decyl-1,2,3,4-tetrahydrophenanthren-4-yl)-3,5-dinitrobenzamide ((±)-1), an analogue of increased lipophilicity of the chiral selector (CS) contained in the Whelk-O^® HPLC chiral stationary phase (CSP) has been resolved into its enantiomers by applying centrifugal partition chromatography (CPC). Considering the known enantioselectivity of the Whelk-O^® CS for naproxen, and the reciprocity concept in enantioseparation, (S)-naproxen related compounds were tested as CSs. In the search for an adequate solvent system, the partition behaviour of the two solutes, CS and racemate, has been studied using several biphasic solvent mixtures. The optimal CS concentration and sample loading capacity were determined in the chosen solvent system. The search for an appropriate CS and solvent system, the scale-up and optimization of the enantiomer separation by CPC, as well as the rationale for the unexpected elution order of enantiomers, are here described. The comparison of the preparative CPC separation achieved with that in HPLC, using a CSP containing an analogous CS, resulted favourable to the former in terms of loading capacity, solvent consumption and throughput.     

Study of the inhibitory effect of ferulic acid on short-chain fatty acids in milk samples by dispersive liquid–liquid micro-extraction in combination with fluorescence derivatization

A sensitive high-performance liquid chromatography (HPLC) method was developed to study the influence of ferulic acid on the formation of volatile fatty acids and lactic acid in milk and soybean milk samples. Volatile fatty acids were extracted by liquid–liquid micro-extraction using chloroform and acetonitrile as the extraction and disperser solvents, respectively. The analytes were derivatized with 2-(5-benzoacridine)ethyl-p-toluenesulfonate that showed excellent fluorescence property and made the sensitive HPLC analysis of short-chain fatty acids become possible. The optimized HPLC sensitivity was in the range of 1.1–1.9?µg?L^?1. Ferulic acid was added in milk and soybean milk samples to study its preservative effect. The results indicated that ferulic acid with concentration of 0.2% (m/v) could effectively reduce the formation of short-chain fatty acids.     

Development and validation of HPLC method for determination of clotrimazole and its two degradation products in spray formulation

A novel simple isocratic HPLC method with UV detection for the determination of three compounds in spray solution (active component clotrimazole and two degradation products imidazole and (2-chlorophenyl)diphenylmethanol) using ibuprofen as an internal standard was developed and validated. The complications with different acido-basic properties of the analysed compounds in HPLC separation - while clotrimazole has pK_a 4.7, imidazole has pK_a 6.9 compared to relatively more acidic (2-chlorophenyl)diphenylmethanol - were finally overcome using a 3.5 μm Zorbax^® SB-Phenyl column (75 mm × 4.6 mm i.d., Agilent Technologies).The optimal mobile phase for separation of clotrimazole, degradation products imidazole and (2-chlorophenyl)diphenylmethanol and ibuprofen as internal standard consists of a mixture of acetonitrile and water (65:35, v/v) with pH* conditioned by phosphoric acid to 3.5. At a flow rate of 0.5 ml min⁻¹ and detection at 210 nm, the total time of analysis was less than 6 min.The method was applied for routine analysis (batch analysis and stability tests) in commercial spray solution.     

Development and application of a capillary electrophoresis based method for the simultaneous screening of six antibiotics in spiked milk samples

An easy to use and low time consuming capillary electrophoresis (CE) method was developed and applied to the simultaneous determination of six antibiotics (ampicillin, amoxicillin, cloxacillin, penicillin, tetracycline and chloramphenicol) in spiked milk samples. Samples of milk were cleaned up by solid-phase extraction (with a C₁₈ cartridge) after protein precipitation. Analysis was performed by CE and results compared with the obtained via HPLC, both coupled to a UV-vis detector (210 nm). CE employed a 58.5 cm long fused-silica capillary (50 cm to detector), 75 μm i.d., a 2.7 × 10⁻² M KH₂PO₄, 4.3 × 10⁻² M Na₂B₄O₇ separation buffer, pH 8; an applied voltage of 18 kV; a hydrostatic injection of 0.5 psi during 3 s; and a run temperature of 25 °C. Under the described conditions, amoxicillin was not separated by HPLC, while CE was able to separate, and, therefore, allow detection. Regardless of amoxicillin, comparable results were obtained by HPLC and CE. The average recoveries of antibiotics, from milk fortified at 2.5 and 5 μg/mL, was over 72% with R.S.D.s within 5%. Recovery levels were essentially dictated by the used SPE cartridge.