硅溶胶-凝胶包埋纳米金和酶的葡萄糖生物传感器

采用溶胶-凝胶技术将金纳米粒子和葡萄糖氧化酶一次性固定于硅溶胶-凝胶的网络结构中,制备了葡萄糖生物电化学传感器并优化了传感器的制备条件。酶电极对葡萄糖具有良好的电化学响应,葡萄糖浓度在0.02~2.0 mmol/L范围内和催化电流呈线性关系,检出限为0.005 mmol/L。酶电极在4 ℃下贮存100 d后对葡萄糖的响应仅下降8%。该酶电极灵敏度高、响应快、稳定性好。     

交联镍纳米片修饰电极用于无酶葡萄糖传感器

以滴涂法在玻碳电极表面修饰一层阳离子交换聚合物Nafion膜,通过离子交换将Ni2+固定于电极表面,进一步电化学沉积得到相互交联的Ni纳米片。Ni纳米片修饰电极能催化葡萄糖的电化学氧化,可用于无酶葡萄糖传感器的构建。在0.60 V恒电位条件下,Ni纳米片修饰电极的氧化峰电流随葡萄糖浓度的增大而增大,其线性响应浓度范围为0.02~3.85 mmol/L。传感器的检测灵敏度为150.6μA(mmol/L)-1·cm-2,检出限为5μmol/L,响应时间为5 s。传感器应用于葡萄糖注射液的检测,加标回收率为90.0%。     

基于谷胱甘肽-壳聚糖自组装的葡萄糖生物传感器

采用壳聚糖-谷胱甘肽复合膜固定葡萄糖氧化酶构建电流型葡萄糖生物传感器。通过循环伏安法对酶膜状态进行表征,实验结果表明,壳聚糖-谷胱甘肽复合膜可以辅助电子传递,提高电极的电流响应。选用正交表L9(34)设计实验方案,分析最佳实验条件。在优化条件下,该传感器对葡萄糖溶液浓度有良好的线性关系,线性范围为1～18 mmol/L,检出限为1.3 mmol/L。实验表明,此传感器具有响应快、稳定性及选择性良好的特点。适用于临床尿样中葡萄糖的测定。     

碳纳米管负载铂-二氧化钌纳米颗粒用于葡萄糖传感器的研究

建立了多壁碳纳米管(MWNTs)负载铂二二氧化钌纳米颗粒的液相化学还原法.以Nafion为固定剂,将Pt-RuO2/MWNTs复合材料修饰于玻碳电极的表面,制备了一种无酶型葡萄糖传感器.实验表明:复合材料修饰的电极对葡萄糖响应电流明显,并且受抗坏血酸(AA)、多巴胺(DA)和尿酸(UA)的干扰小.本实验采用安培法测定葡萄糖,线性范围为2 0×10 3～1.0×10-2 mol/L(R～0.9965);灵敏度为119.26 μA cm-2(mmol/L)-1;检出限为1.25×10 -5 mol/L(信噪比为3);响应时间为4.8 s.PtRuO2/MWNTs修饰电极可作为性能良好的无酶型葡萄糖传感器.     

鱼鳔膜为基质的生物传感器测定葡萄糖的研究

以鱼鳔膜为基质同定葡萄糖氧化酶,偶联氧电极,构建了葡萄糖生物传感器,通过测定溶解氧浓度的变化定量测定葡萄糖.考察了酶浓度、pH值、缓冲液浓度对传感器的影响,优化了实验条件:即酶浓度为1 mg,pH 7.0,缓冲液浓度为100 mmol/L.此传感器具有较宽的线性范围(0.016～1.2 mmol/L),较短的响应时间(...     

纳米金葡萄糖氧化酶修饰电极对葡萄糖的电化学行为研究

利用自组装技术固定化酶稳定的优点,及纳米金的高灵敏电催化作用制备了纳米金修饰葡萄糖氧化酶修饰金电极.结果表明,制备的修饰电极对葡萄糖具有很好的电催化氧化功能.在选择的条件下,修饰电极对葡萄糖在0～28 mmol/L浓度范围内呈线性响应,响应时间为15 s,检出限为0.27 mmol,响应电流的平均密度为33.52 nA/cm2,两周后响应值保持88%,可满足实际应用要求.     

利用层层累积技术制备基于纳米碳管的葡萄糖生物传感器

以多壁纳米碳管(MWNTS)为电子媒介体和酶的吸附载体,利用层层累积的自组装技术固定葡萄糖氧化酶(GOX)的多层(MWNTa/GOx).复合薄膜修饰电极,制备了一种新型葡萄糖生物传感器.结果表明,传感器对葡萄糖的响应电流值随着MWNTa//GOx复合薄膜层数的不同而变化,当MWNTa//GOx复合薄膜的层教为6时,响应电流值迭到最大.(MWNTs/GOx).复合薄膜修饰的葡萄糖生物传感器对30mmol/L葡萄糖的响应电流为1.63μA,响应时间仅为6.7 s.该生物传感器检测的线性范围为0.5～15 mmol/L,最低检测浓度可达0.09 mmol/L.     

光导纤维电化学发光葡萄糖传感器的研究

以碳糊为固定化载体 ,将葡萄糖氧化酶固定在碳糊电极上 ,制成了光导纤维电化学发光葡萄糖生物传感器。葡萄糖的酶催化反应、鲁米诺的电化学氧化和化学发光反应在电极表面同时发生 ,因此该传感器的信号响应在 1 0 s内达到发光强度峰值。葡萄糖浓度在 1 .0× 1 0 -5～ 2 .0× 1 0 -2 mol/L范围内与发光强度呈线性关系 ,检出限为 6.4× 1 0 -6mol/L,可应用于市售饮料中葡萄糖的测定     

基于金纳米棒-壳聚糖复合膜的葡萄糖生物传感器

本文采用金纳米棒-壳聚糖复合膜固定葡萄糖氧化酶构建电流型葡萄糖生物传感器.通过电化学交流阻抗法和循环伏安法对酶膜状态进行了表征,得到了相应的等效电路和动力学参数.实验结果表明,金纳米棒-壳聚糖复合膜可以辅助电子传递,提高电极的电流响应,并使生物传感器的使用温度范围有很大的扩展.此传感器表现出对葡萄糖溶液浓度的优良响应,线性范围在2.78×10^-5mol/L—2.22×10^-3mol/L,响应灵敏度约为7.819μA·cm^-2(mmol/L)^-1,表观米氏常数为10mmol/L.本工作还研究了温度和溶液pH值对电极电流响应的影响.     

高性能多级花状Co3O4基无酶葡萄糖电化学传感器

以硝酸钴、碳酸钠、尿素为原料,泡沫镍为基体,采用水热和煅烧相结合的二步法制备了一种多级花状Co_3O_4/Ni异质结构的无酶葡萄糖传感器。通过X射线衍射与扫描电镜对Co_3O_4/Ni电极的成分及形貌进行了表征,并采用循环伏安法在1mol/L KOH溶液中测试了Co_3O_4/Ni异质结构葡萄糖传感器电极的电化学性能。结果表明,通过二步法在泡沫镍表面制备的Co_3O_4呈现多级花状纳米纤维结构。将制备的Co_3O_4/Ni异质结构作为电极构建的无酶葡萄糖传感器表现出响应时间快(低于5s)、检测灵敏度高(7.4m A·(mmol/L)~(-1)·cm~(-2))、检出限低(1.17μmol/L,S/N=3)和线性检测范围宽(0~5 mmol/L)的特点。进一步的抗干扰性检测表明所制备的传感器在+0.44V vs.SCE对葡萄糖表现出良好的选择性。本文所制备的多级花状Co_3O_4基电极在无酶葡萄糖传感器的发展中有着很大的应用潜力。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Copper catalyzed/mediated synthetic methodology for ebselen and related isoselenazolones

Scope of the copper catalyzed/mediated selenium-nitrogen coupling reaction has been studied for the synthesis of isoselenazolones. It is noticed that the 2-chloro, 2-bromo-, and 2-iodo-aryl amides substrates can be exploited in the selenium-nitrogen coupling reaction by employing 25-100 mol % of CuI/1,10-phenanthroline (L) and potassium carbonate as a base in DMF. Furthermore, electron rich 2-chloro-arylamides also underwent selenium-nitrogen coupling reaction to give biologically important selenium-nitrogen heterocycles. Also, copper-catalyzed selenium-nitrogen coupling reaction has been meticulously applied for the synthesis of diaryl diselenides having methoxy, amine, and amide functionality from respective aryl iodides in the presence of stoichiometric amount of succinimide as an external Se-N coupling partner.     

Knoevenagel condensation catalyzed by novel Nmm-based ionic liquids in water

A series of novel N-methyl morpholine (Nmm) based ionic liquids with 1,2-propanediol group were synthesized and used as catalysts for Knoevenagel condensation at room temperature in water. Under the effect of the catalyst, various aldehydes or aliphatic ketones could react with a wide range of activated methylene compounds well, including malononitrile, alkyl cyanoacetate, cyanoacetamide, β-diketone, barbituric acid, 2-arylacetonitrile and thiazolidinedione. Furthermore, most of the products could be separated just by filtrating and washing with water. Additionally, the catalyst is recyclable and applicable for the large-scale synthesis.     

Construction of polyheterocyclic spirotetrahydrothiophene derivatives via sulfa-Michael/aldol cascade reaction

A series of polyheterocyclic spirotetrahydrothiophene derivatives were obtained in moderate to excellent yields via a catalyst-free sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 under mild conditions. We also present the first asymmetric sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 with moderate to good enantioselectivities catalyzed by readily available chiral phase-transfer catalysts (PTCs).     

Suzuki-Miyaura reactions of the soluble guanylate cyclase inhibitor NS2028: a non-product specific route to C-8 substituted analogues

Both soluble guanylate cyclase (sGC) inhibitors ODQ 1 and NS2028 2 are synthesized via improved protocols. In the former case treating 3,4-dihydroquinoxalin-2(1H)-one oxime 8, which can be prepared in two steps from 1,2-benzenediamine, with 1,1′-carbonyldiimidazole (CDI) gives the dihydro-ODQ 10 that in the presence of KMnO₄ oxidises to give ODQ 1 in an overall yield of 46% starting from 1,2-benzenediamine. In the latter case, the synthesis affords NS2028 2 from 2-amino-4-bromophenol 3 in three steps with an overall yield of 85% and avoids the need for chromatography. Furthermore, Suzuki-Miyaura reaction conditions are described that enable the preparation of 8-aryl and 8-heteroaryl derivatives of NS2028 directly from NS2028 2. Finally, demethylation of the 8-(methoxyphenyl) substituted analogues afforded the 8-(hydroxyphenyl) derivatives 40-42. All new products are fully characterised.