Anisotropic swelling of hydrogel nanowires based on poly(vinylpyrrolidone) fabricated by single‐particle nanofabrication technique

We report a hydrogel nanowire based on poly(vinylpyrrolidone) (PVP) and N,N'‐methylenebis(acrylamide) (MBA), which have anisotropic swelling ratio for radius and length direction. The PVP/MBA nanowires were fabricated by single particle nanofabrication technique, which is a technique for the fabrication of polymeric nanowires using the single ion event, that cause the crosslinking reaction of polymer chains within the ion tracks along the ion paths; furthermore the size (length and radius) of the nanowires was controlled by changing the film thickness and amount of MBA crosslinker. The swelling behaviors in air and water were observed using atomic force microscopy. The PVP/MBA nanowires exhibited anisotropic swelling along the length and radius in aqueous environments, because the hydrogel nanowires consisted of crosslinked networks with inhomogeneous crosslinking points, which reflected the initial energy distribution from incident an ion within the ion track. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1950–1956     

利用模板法制备Ag纳米线

利用阳极氧化铝（AAO）作为模板,制备出高定向的Ag纳米线．Ag纳米线的形貌由环境扫描电镜证实,并通过X-射线能谱（EDX）、X-射线粉末衍射谱（XRD）测试手段进行了表征．     

Erythrocyte-like liposomes prepared by means of amphiphilic cyclodextrin sulfates

A novel class of sulfated glycolipids with excellent self-assembling capacity to form stable monolayers at an air-water interface and specific erythrocyte-like liposomes was synthesised from alpha, beta, and gamma-cyclodextrins as starting materials.     

Transferrin recognition based on a protein imprinted material prepared by hierarchical imprinting technique

A novel kind of transferrin imprinted polymer particles was synthesized by a hierarchical strategy. First, transferrin was immobilized on silica beads by non-covalent absorption. Then, a pre-polymerization mixture, composed of 1,4-bis(acryloyl)piperazine, methacrylamide, methacrylic acid, ammonium sulfate and polyoxyethylene sorbitan monolaurate, was irrigated into the pores of silica particles, and polymerized at 25 °C. Finally, the silica matrix was etched with ammonium hydrogen fluoride, not only to remove the template protein, but also to expose protein recognition sites on the surface of the imprinted polymer. The binding capacity of the transferrin-imprinted particles is 6.3 mg of protein per gram of material, and the time required to reach adsorption equilibrium was less than 10 min. The imprinting factor of transferrin is ca. 3.3 in the presence of ribonuclease B, cytochrome c and β-lactoglobulin. The results indicate that these imprinted polymer particles can recognize transferrin with good selectivity, high binding capacity and fast mass transfer. They may be applied as an artificial antibody to remove the high abundance proteins in plasma.

Transferrin recognition based on a protein imprinted material prepared by hierarchical imprinting technique

A novel kind of transferrin imprinted polymer particles was synthesized by a hierarchical strategy. First, transferrin was immobilized on silica beads by non-covalent absorption. Then, a pre-polymerization mixture, composed of 1,4-bis(acryloyl)piperazine, methacrylamide, methacrylic acid, ammonium sulfate and polyoxyethylene sorbitan monolaurate, was irrigated into the pores of silica particles, and polymerized at 25 °C. Finally, the silica matrix was etched with ammonium hydrogen fluoride, not only to remove the template protein, but also to expose protein recognition sites on the surface of the imprinted polymer. The binding capacity of the transferrin-imprinted particles is 6.3 mg of protein per gram of material, and the time required to reach adsorption equilibrium was less than 10 min. The imprinting factor of transferrin is ca. 3.3 in the presence of ribonuclease B, cytochrome c and β-lactoglobulin. The results indicate that these imprinted polymer particles can recognize transferrin with good selectivity, high binding capacity and fast mass transfer. They may be applied as an artificial antibody to remove the high abundance proteins in plasma.

A novel kind of transferrin imprinted polymer particles was synthesized by a hierarchical strategy. Transferrin was immobilized on silica beads by non-covalent absorption. The pre-polymerization mixture was irrigated into the pores of silica particles and polymerized at 25°C. After the removal of the silica matrix and template protein, protein recognition sites were exposed on the surface of the prepared polymer and applied for the transferrin recognition

     

Sorption of phenols by single and mixed cyclodextrin polymers

Cyclodextrin (CD) hydrogels were synthesized by a crosslinking reaction with the same cyclodextrin/epichlorohydrin mole ratio (1/11) using αCD, βCD, γCD, and 50:50 mixtures of α/βCD and β/γCD. In order to investigate the sorption capacity of these hydrogels to different solutes, five model molecules have been selected: phenol, 3-nitrophenol, 4-nitrophenol, 1-naphthol, and the antiinflamatory drug diflunisal. The amounts sorbed have been related to the different affinities of the solutes. 1-naphthol shows the highest affinity for these polymers, especially in the case of sorbents containing βCD. The sorption is considerably poorer for phenol than for its nitro derivatives. The two structural isomers 3- and 4-nitrophenol show significant differences in their affinities towards αCD, βCD and α/βCD. Finally, in the case of diflunisal, a bulkier model molecule, remarkable differences were found on the sorption behaviour by polymers whose cyclodextrins have a similar affinity for this solute (βCD, γCD, and β/γCD).     

环糊精在金属酶模拟中的应用

非共价作用（如氢键、静电和疏水作用）普遍存在于天然金属酶中,对酶活化或底物催化过程有重要的协同作用.近年来基于超分子化学理论的金属酶模拟研究不断向酶的活性中心亚稳态和次层结构的生物功能模拟方向发展.本文将根据报道的文献并结合本课题组的研究工作,对环糊精（一种重要的超分子主体）构建金属酶模型的研究进行综述.     

A new fluorescent particle prepared by chemical stabilized phycobilisome

Natural phycobilisomes(PBSs) were isolated and purified from a red macroalga,Polysiphonia urceolata,by multi-step of sucrose gradient centrifugation,and were chemically stabilized by small molecule cross-linker formaldehyde.The stabilized PBSs showed similar absorption and fluorescent properties at room temperature compared to natural PBSs and kept a steady F672/F580 value during more than 3 months of storage in 0.45 mol/L phosphate buffer(pH 6.8) or at low temperature at 77 K.The stabilized PBS migrated...     

Hybrid polysaccharide-silica nanocomposites prepared by the sol-gel technique

New monolithic nanocomposite silica biomaterials were synthesized on the basis of various natural polysaccharides and recently introduced completely water-soluble precursor tetrakis(2-hydroxyethyl) orthosilicate. The sol-gel processes were performed in aqueous solutions without the addition of organic solvents and catalysts. The silica polymerization was promoted by the polysaccharides through acceleration and catalytic effect on the processes. By introducing poly(vinyl alcohol) or poly(ethylene oxide) in the precursor solution, it was shown that the jellification took place in the case of the hydroxyl-containing polymer. Therefore, it was suggested that the catalysis was caused by a formation of hydrogen bonds between hydroxyl groups in macromolecules and products of precursor hydrolysis (silanols). It was also demonstrated that the polysaccharides radically changed the structure of biomaterials. In place of the cross-linked nanoparticles, there was a three-dimensional network from crossed or branched fibers and uncrossed spherical particles that filled the mesh space. The density of network, thickness of fibers, and properties of synthesized biomaterials depended on the polysaccharide type, charged degree of their macromolecule, and concentration. By varying these parameters, it was possible to manipulate the structural organization of hybrid polysaccharide-silica nanocomposites.     

A novel gaseous pinacolyl alcohol sensor utilizing cataluminescence on alumina nanowires prepared by supercritical fluid drying

A cataluminescence (CTL) sensor using Al₂O₃ nanowires as the sensing material was developed for the determination of trace pinacolyl alcohol in air samples based on the catalytic chemiluminescence (CL) of pinacolyl alcohol on Al₂O₃ nanowires. Eight catalysts were examined and the CL intensity on Al₂O₃ nanowires prepared by supercritical fluid drying was the strongest. This novel CL sensor showed high sensitivity and selectivity to gaseous pinacolyl alcohol at optimal temperature of 340 °C. Quantitative analysis was performed at a wavelength of 460 nm. The linear range of CTL intensity versus concentration of gaseous pinacolyl alcohol was 0.09 × 10⁻⁶ to 2.56 × 10⁻⁶ g mL⁻¹ (r = 0.9983, n = 6) with a detection limit (3σ) of 0.0053 × 10⁻⁶ g mL⁻¹. None or only very low levels of interference were observed while the foreign substances such as water vapor, ethanol, ammonia, chloroform, benzene, nitrogen dioxide, methylbenzene, hydrochloric acid, methanol and butanol were passing through the sensor. The response time of the sensor is less than 100 s, and the sensor had a long lifetime more than 60 h. The sensor would be potentially applied to analysis of the nerve agents such as Soman.     

Highly branched aromatic polymers prepared by single step syntheses

Highly branched polyphenylenes, polyphenylene ethers, aromatic polyesters and polyamides synthesized from AB₂ type monomers are reviewed. Polyphenylenes were obtained by aryl-aryl coupling reactions of 3,5-dihalo-phenyl organometallic reagents. ¹³C NMR indicates about 70% branching efficiency. A T_gat 236°C was observed, but the polymer did not form films. Polyethers were prepared by oxidative coupling of 2,4,6-tribromophenol and 2,4-dibromophenol. The former monomer gave high molecular weight polymers but the latter monomer did not polymerize well. Condensation of 3,5-diaminobenzoic acid (I) and 3-aminoisophthalic acid derivatives in an amide solvent gave lyotropic hyperbranched aromatic polyamides. The GPC indicated a large degree of polymer aggregation in the amide solvent in the absence of a complexing salt.     

Enhanced UV photosensing properties of ZnO nanowires prepared by electrodeposition and atomic layer deposition

A new process enabling the synthesis of zinc oxide (ZnO) and Al-doped ZnO nanowires (NWs) for photosensing applications is reported. By combining atomic layer deposition (ALD) for the seed layer preparation and electrodeposition for the NW growth, high-quality ZnO nanomaterials were prepared and tested as ultraviolet (UV) sensors. The obtained NWs are grown as arrays perpendicular to the substrate surface and present diameters between 70 and 130 nm depending on the Al doping, as seen from scanning electron microscopy (SEM) studies. Their hexagonal microstructure has been determined using X-ray diffraction and Raman spectroscopy. An excellent performance in UV sensing has been observed for the ZnO NWs with low Al doping, and a maximal photoresponse current of 11.1 mA has been measured. In addition, initial studies on the stability have shown that the NW photoresponse currents are stable, even after ten UV on/off cycles.     

Sensitive sandwich immunoassay based on single particle mode inductively coupled plasma mass spectrometry detection

A sensitive sandwich type immunoassay has been proposed with the detection by inductively coupled plasma mass spectrometry (ICP-MS) in a single particle mode (time resolved analysis). The signal induced by the flash of ions (¹⁹⁷Au⁺) due to the ionization of single Au-nanoparticle (Au-NP) label in the plasma torch can be measured by the mass spectrometer. The frequency of the transient signals is proportional to the concentration of Au-NPs labels. Characteristics of the signals obtained from Au-NPs of 20, 45 and 80 nm in diameters were discussed. The analytical figures for the determination of Au-labeled IgG using ICP-MS in conventional integral mode and single particle mode were compared in detail. Rabbit-anti-human IgG was used as a model analyte in the sandwich immunoassay. A detection limit (3σ) of 0.1 ng mL⁻¹ was obtained for rabbit-anti-human IgG after immunoreactions, with a linear range of 0.3-10 ng mL⁻¹ and a RSD of 8.1% (2.0 ng mL⁻¹). Finally, the proposed method was successfully applied to spiked rabbit-anti-human IgG samples and rabbit-anti-human serum samples. The method resulted to be a highly sensitive ICP-MS based sandwich type immunoassay.     

Nanostructures of functionalized gold nanoparticles prepared by particle lithography with organosilanes

Periodic arrays of organosilane nanostructures were prepared with particle lithography to define sites for selective adsorption of functionalized gold nanoparticles. Essentially, the approach for nanoparticle lithography consists of procedures with two masks. First, latex mesospheres were used as a surface mask for deposition of an organosilane vapor, to produce an array of holes within a covalently bonded, organic thin film. The latex particles were readily removed with solvent rinses to expose discrete patterns of nanosized holes of uncovered substrate. The nanostructured film of organosilanes was then used as a surface mask for a second patterning step, with immersion in a solution of functionalized nanoparticles. Patterned substrates were fully submerged in a solution of surface-active gold nanoparticles coated with 3-mercaptopropyltrimethoxysilane. Regularly shaped, nanoscopic areas of bare substrate produced by removal of the latex mask provided sites to bind silanol-terminated gold nanoparticles, and the methyl-terminated areas of the organosilane film served as an effective resist, preventing nonspecific adsorption on masked areas. Characterizations with atomic force microscopy demonstrate the steps for lithography with organosilanes and functionalized nanoparticles. Patterning was accomplished for both silicon and glass substrates, to generate nanostructures with periodicities of 200-300 nm that match the diameters of the latex mesospheres of the surface masks. Nanoparticles were shown to bind selectively to uncovered, exposed areas of the substrate and did not attach to the methyl-terminal groups of the organosilane mask. Billions of well-defined nanostructures of nanoparticles can be generated using this high-throughput approach of particle lithography, with exquisite control of surface density and periodicity at the nanoscale.     

Towards biosensors based on conducting polymer nanowires

We report the electrochemical deposition of poly(pyrrolepropylic acid) nanowires, their covalent modification with antibodies and their conversion into potential functional sensor devices. The nanowires and the devices were characterised by optical microscopy, fluorescence microscopy, electron microscopy and electrical measurements. Fluorescence images, current–voltage (I–V) profiles and real-time sensing measurements demonstrated a rapid and highly sensitive and selective detection of human serum albumin (HSA), a substance that has been used to diagnose incipient renal disease. The detection is based on the selective binding of HSA onto anti-HSA that is covalently attached to the nanowires. The binding changes the electrical properties of the nanowires thus enabling the real-time detection. Whilst the utility of the research was demonstrated for protein binding/detection, the technology could easily be designed for the detection of other analytes by the modification of polymer nanowires with other analyte-specific molecules/biomolecules. Therefore, the technology has the potential to positively impact broad analytical applications in the biomedical, environmental and other sectors. Figure Real-time dynamic current response on sequential exposure of buffer, bovine serum albumin (BSA) and human serum albumin (HSA) onto anti-HSA modified poly (pyrrolepropylic acid) nanowires. Fluorescence images of poly(pyrrolepropylic acid) nanowire (top right) and polypyrrole nanowire control (bottom right) after sequential treatment with 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide hydrochloride (EDC), anti HSA and fluorophore-labeled HSA.     

Precise analysis of thyroxine enantiomers in pharmaceutical formulation by mobility difference based on cyclodextrin

Identification and determination of chiral pharmaceutical residues is still a challenging analytical puzzle. In this work, a simple, rapid, and effective method for chiral D/L-tetraiodothyronine (T4) separation and quantitative was developed based on host–guest recognition using ion mobility spectrometry-mass spectrometry (IMS-MS). The D/L-T4 enantiomers were mobility separated by their diastereomeric complexes through mixing with cyclodextrin (CD) and metal ions. D/L-T4 was first separated by complexing with host molecule (α-, β-, γ-CD), observing weak peak-to-peak resolution (R_p-p) by the formed binary complex [CD + D/L-T4-H]⁺, and the R_p-p decreased with the CD size increasing. However, the separation effect of D/L-T4 was much improved with the addition of divalent metal ions (G²⁺) by the formed ternary complex [CD + D/L-T4 + G]²⁺. In comparison, α-CD related complexes can possess the best separation effect for D/L-T4 in most cases. Considering the high selectivity, non-toxic, and chemically stable of β-CD, [β-CD + D/L-T4 + Ca]²⁺ was selected for D/L-T4 analysis (R_P-P = 0.764). Whereafter, chemical theoretical conformations for [β-CD + D/L-T4 + H]⁺ and [β-CD + D/L-T4 + Ca]²⁺ were optimized, discovering similar micro-interaction modes between [β-CD + D-T4 + H]⁺ and [β-CD + L-T4 + H]⁺; while with the addition of Ca²⁺, significantly different interaction modes were observed between [β-CD + D-T4 + Ca]²⁺ and [β-CD + L-T4 + Ca]²⁺. And theoretical collision cross section (CCS) trends for the complexes were consistent with that of the experimental results. Additionally, calibration curves were linear within 1.00 to 10⁴ ng mL^?1 with coefficient (R² > 0.99), gaining the limit of detection (LODs) calculation of 0.11 ng mL^?1, and the detection range between D-T4 and L-T4 of 45.6:1 to 1:59.8. Finally, the method was applied for D/L-T4 detection in Levothyroxine tablets, the detection content has good consistency on drug labeling. Because the proposed method exhibited good analytical performance in terms of speed, selectivity, sensitivity, and reproducibility of the measurements, that can be a promising strategy for effective D/L-T4 detection in pharmaceutical industries or other practical samples.     

Polyoxymethylene prepared by γ-ray-induced polymerization of tetraoxymethylene single crystal

Summary In order to prepare a large single crystal, tetraoxymethylene recrystallized by distilled water adjusted to pH 8 was sealed in an ampoule at a reduced pressure of 1 mm Hg and was crystallized in a furnace with the temperature gradient of 6 °C/cm. The lowering rate of the ampoule was required to be 6 cm/day for preparing the single crystal with 1 cm diameter and to be 3 cm/day for one with 2 cm diameter. The optimum angle at the pointing end of the ampoule, where a seed crystal is formed, was about 40°. The b-axis of the obtained single crystal was parallel to the direction of the crystal growth i. e. the wall of the ampoule. It was polymerized byγ-ray under conditions which prevent the growth of the twin crystal. The obtained polyoxymethylene was porous, because the polymerization yield of 100% could not be attained. However, it was so tough that a specimen for measurements could be cut down by a diamond cutter. Its fiber axis was parallel to the direction of the wall of the ampoule. It did not contain the so-called amorphous regions, although it did contain defects. It was characterized with the extremely high orientation of the polymer chains.

---

Zusammenfassung Zur Pr?parierung gro?er Einkristalle wurde rekristallisiertes Tetraoxymethylen in destilliertem Wasser von p_H 8 in eine Ampulle bei einem reduzierten Quecksilberdruck von 1 mm eingefüllt und in einem Ofen mit einem Temperaturgradienten von 6 °C/cm kristallisiert. Die Abkühlgeschwindigkeit der Ampulle betrug etwa 6 cm/Tag für die Pr?paration eines Einkristalls mit 1 cm ? und 3 cm/Tag für einen solchen mit 2 cm ?. Der optimale Winkel am spitzen Ende der Ampulle, wo der Keimkristall gebildet wird, betrug etwa 40°. Dieb-Achse des Einkristalls war parallel zur Wachstumsrichtung, d. h. zur Wand der Ampulle. Der Kristall wurde durch R?ntgenstrahlen polymerisiert unter Bedingungen, die das Wachsen eines Zwillingskristalls vermeiden. Das erhaltene Polyoxymethylen war por?s, doch konnte eine Polymerisationsausbeute von 100% nicht erhalten werden. Doch war der Einkristall so z?h, da? für Messungen eine Probe mit dem Diamantschneider abgeschnitten werden konnte. Die Faserachse war parallel zur Wandrichtung der Ampulle. Das kristalline Material enthielt keine sogenannten amorphen Bereiche, allerdings Defekte. Es war durch extrem hohe Orientierungen der Polymerketten charakterisiert.

---

---

We are greatly indebted to Dr.Y. Miyake of Mitsui Toatsu Co., Ltd. for providing the tetraoxymethylene. Thanks are to due Dr.M. Nishii of Osaka Laboratories, Japan Association for Radiation Research on Polymer for the radiation polymerization, to Mr.T. Tsukihara for the X-ray measurement, and to Mrs.H. Tanaka for the help with the electron microscopy. We are also grateful to Prof.S. Seki for offering the use of differential scanning calorimeter.     

基于大科学装置的空间金属组学和单细胞/单颗粒金属组学

金属组学是综合研究生命体内（(特别是细胞内）)自由或络合的全部金属原子的分布、含量、化学种态及其功能的一门学科,而大科学装置为金属组学研究提供了强有力的工具。本综述本文首先介绍了金属组学发展简史,然后介绍了基于大科学装置的同步辐射技术、中子技术、质子技术及缪子技术等,最后概述了基于大科学装置的空间金属组学、单细胞/单颗粒金属组学的应用示例。基于大科学装置的中子活化技术（NAA）NAA、X-射线荧光光谱（XRF）以及质子激发X射线谱（PIXE ）等技术是开展非原位空间金属组学研究的有力手段,而XRF、PIXE以及缪子X射线荧光谱（MXA）为开展原位空间金属组学提供了有力工具,特别是基于XRF的技术,其空间分辨率可低至10 nm级别,是开展原位单细胞/单颗粒金属组学的利器。 新一代同步辐射光源、质子源及缪子源将为空间金属组学、特别是时空金属组学研究提供更强有力工具。     

Fabrication of lead titanate single crystalline nanowires by hydrothermal method and their characterization

Single crystalline nanowires of lead titanate (PbTiO₃) were fabricated by hydrothermal method at 200°C using lead acetate and n-tetrabutyl titanate as starting materials, where sodium hydroxide was served as a mineralizer. Crystalline phases, microstructure and optical properties of PbTiO₃ nanowires were investigated. The PbTiO₃ nanowires were uniform and continuous along the long axis, and were composed of single crystalline PbTiO₃ with a tetragonal perovskite structure. The diameter of a single nanowire was around 12 nm and the length reached up to 3 μm. The chemical composition of the samples and the valence states of elements were determined by X-ray photoelectron spectroscopy (XPS). The ultraviolet/visible absorption spectroscopic investigation suggested that the absorption edge of optical transition of the first excitonic state occurred at around 320 nm. A blue-green light emission peaking at about 471 nm (2.63 eV) is observed at room temperature, and the intensity of this emission increased with increasing excitation wavelength. Oxygen vacancies are responsible for the light emission of PbTiO₃ nanowires.     

Sugar sensing based on induced pH changes

A sensory assembly consisting of a pH sensitive NIR dye and an arylboronic acid shows ratiometric absorption changes with increased fluorescence intensity upon addition of sugar in aqueous media; this demonstrates a new signal transduction mechanism for the detection of sugar based on pH changes induced in the microenvironment of the sensory assembly.