Synthesis of Acetic Acid on Pd—H4SiW12O40—Based Catalysts by Direct Oxidation of Ethylene

Synthesis of acetic acid by direct oxidation of ethylene on Pd-H4SiW12O40-based catalysts was studied in a fixed-bed integral reactor and a pulse differential reactor,From the performance of the catalysts with different compositions and configurations,it is proposed that acetic acid is predominantly produced via an intermediate of acetaldehyde ,This can be easily confirmed by comparing the product distributions in the integral and the differential reactors,The active sites for acetic acid formation are considered to exist mainly at the boundaries between the H2SiW12O40 and the Pd particles,The Pd-based catalysts reduced by H2/N2 have higher activities than those reduced by hydrazine,as explained by the degree of Pd dispersion obtained from the characteristics of hydrogen chemical adsorption It was found that the Pd-Se-SiW12/SiO2 catalyst with selenium tetrachloride as a precursor was more active than that with potassium selenite ,and that the acetic acid yield can be greatly increased by adding a suitable amount of dichloroethane (C2H4Cl2/C2H4 mole ratio=0.03) to the reactants.     

载体和担载酸对乙烯直接氧化合成乙酸反应的影响

 在固定床流动反应器上研究了Pd－酸／载体体系催化乙烯直接氧\r\n化合成乙酸的反应，并对载体相同但担载酸强度不同的催化剂的催化活\r\n性进行了比较．结果表明，担载酸的强度明显影响催化剂的活性，酸强\r\n度越大其催化活性越高．用NH3－TPD和异丙醇脱水探针反应表征了二氧\r\n化硅、活性碳和酸性白土三种载体担载的Pd－H4SiW12催化剂的酸性，\r\n并测试了三种催化剂的催化活性．结果表明，载体通过影响担载酸的强\r\n度而影响催化剂的活性，载体上的强酸中心越多，催化剂的活性越高．\r\n测定了二氧化硅、活性碳和酸性白土三种载体担载的Pd－H4SiW12催化\r\n剂上Pd的分散度，并与其催化活性相关联．结果表明，决定乙烯直接氧\r\n化生成乙酸反应活性的主要因素是催化剂的酸强度而不是Pd的分散度．     

不同前驱体制备的Mn-H4SiW12O40/SiO2 催化剂对二甲醚催化氧化制取甲缩醛反应性能的影响

采用浸渍法分别用硫酸锰、醋酸锰、氯化锰和硝酸锰为原料制备了Mn-H4SiW12O40/SiO2 杂多酸催化剂。在常压连续流动固定床反应器中，考察了二甲醚选择氧化制取甲缩醛的反应活性。实验结果表明，催化剂的催化活性顺序为Mn-Cl2H4SiW12O40/SiO2>Mn(NO3)2H4SiW12O40/SiO2>MnSO4H4SiW12O40/SiO2>Mn(AC)2H4SiW12O40/SiO2。并进一步考察了反应温度对不同锰盐前驱体催化剂性能的影响。结果表明，随温度的升高，硫酸锰修饰的H4SiW12O40/SiO2 催化剂催化氧化比较剧烈，在613K时二甲醚转化率高达42.4%，但此时甲缩醛选择性仅为0.9%。采用氯化锰修饰的H4SiW12O40/SiO2催化剂，二甲醚催化氧化反应较缓和，并且甲缩醛的选择性明显高于分别采用硫酸锰、醋酸锰和硝酸锰改性的催化剂，在593K反应1h时，二甲醚转化率为8.6%，甲缩醛选择性达到37.5%。H2-TPR结果显示，硫酸锰改性的催化剂高温氧化性能明显强于另外三种催化剂，氯化锰的修饰使得催化剂的低温氧化性能变强。XRD结果表明，MnCl2 H4SiW12O40/SiO2催化剂的衍射特征峰明显强于其他三种催化剂，并且发现了MnO2衍射特征峰。     

Keggin结构纳米硅钨酸铵的室温固相合成与物性

首次以H4SiW12O40 * 22H2O和(NH4)2C2O4 * H2O为原料,室温固相反应合成出(NH4)4SiW12O40纳米微粒;用元素分析、 FTIR确定产物的组成和结构; XRD、 TEM和BET对产物的形貌、晶粒尺寸和比表面积进行了表征; TG-DTA确定了产物的稳定温区.结果表明,产物为纳米粒子,平均粒径为60 nm,比表面积为108.7 m2/g,在430℃以下具有良好的热稳定性.在固相反应中,研磨和放热反应热效应能加快反应物扩散速率和生成物成核速率,使产物粒径减小;反应物含有结晶水和生成物H2C2O4 * 2H2O,对形成小粒径的(NH4)4SiW12O40纳米粒子起关键作用.     

A microwave-assisted and heteropolyacids-catalysed cyclocondensation reaction for the synthesis of 4(3H)-quinazolinones

We have investigated a microwave-assisted synthesis of 4(3H)-quinazolinones by condensation of anthranilic acid, orthoesters (or formic acid) and substituted anilines,using Keggin-type heteropolyacids (H(3)PW(12)O(40).13H(2)O, H(4)SiW(12)O(40).13H(2)O,H(4)SiMo(12)O(40).13H(2)O or H(3)PMo(12)O(40).13H(2)O) as catalysts. We found that the the use of H(3)PW(12)O(40).13H(2)O acid coupled to microwave irradiation allows a solvent-free, rapid (approximately 13min) and high-yielding reaction.     

H4SiW12O40和双偶极Ru(II)配合物形成的静电自组装多层膜

制备了含有H4SiW12O40和双偶极Ru(II)配合物交替层的一个新颖静电自组装多层膜.用紫外可见光谱、循环伏安学、原子力显微镜对薄膜进行了表征和性质研究.结果表明膜沉积平稳、均匀,所制得的薄膜具有较好的电化学活性.AFM图像表明钌(II)配合物和H4SiW12O40层具有明显不同的微区结构.     

Oxidative cross-coupling of acrylates with vinyl carboxylates catalyzed by a Pd(OAc)2/HPMoV/O2 system

Oxidative cross-coupling of acrylates with vinyl carboxylates was first successfully achieved by the use of a Pd(OAc)(2)/HPMoV/O(2) system in fair to good yields. For instance, the reaction of n-butyl acrylate with vinyl acetate in the presence of catalytic amounts of Pd(OAc)(2) and H(4)PMo(11)VO(40).nH(2)O under O(2) in acetic acid at 70 degrees C for 12 h afforded the corresponding cross-coupling product, n-butyl 5-(acetoxy)-2,4-pentadienoate, in 70% yield.     

H_2O-DMSO体系中联吡啶甲基化及其钨硅酸盐的形成

以Keggin型钨硅酸H_4[SiW_(12)O_(40)]·24H_2O和MN~(2+)为原料,4,4′-联吡啶(4,4′-bipy)为有机前驱体,水和二甲基亚砜(DMSO)为混合溶剂,在水热条件下,4,4′-bipy发生N-甲基化,并与DMSO共同修饰[SiW_(12)O_(40)]~(4-)阴离子,形成了1个钨硅酸盐基无机-有机杂化化合物(CH_3)_2bipy)((CH_3)_2SOH)_2[SiW_(12)O_(40)].通过元素分析、红外光谱(IR)、热重(TG)及X-射线单晶衍射分析对该化合物进行了表征,初步探讨了该化合物的形成条件,并研究了其在水溶液中的电化学性质及其对H_2O_2还原的电催化活性.     

新型苯并咪唑杂多酸盐离子液体的制备及其在催化合成己二酸中的应用

以1-丁基苯并咪唑为起始原料,合成了1-丁基-3-(4-磺酸基丁基)苯并咪唑內盐(1),1-丁基-3-羧甲基苯并咪唑氯盐(2)和1,3-二丁基苯并咪唑溴盐(3);1~3分别与硅钨酸、磷钨酸和磷钼酸在水或者乙醇中反应,合成了5种新型的杂多酸盐离子液体——1-丁基-3-(4-磺酸基丁基)苯并咪唑硅钨酸盐(4a),1-丁基-3-(4-磺酸基丁基)苯并咪唑磷钨酸盐(4b),1-丁基-3-(4-磺酸基丁基)苯并咪唑磷钼酸盐(4c),1-丁基-3-羧甲基苯并咪唑硅钨酸盐(5)和1,3-二丁基苯并咪唑硅钨酸盐(6),其结构经1H NMR,13C NMR和IR表征。并考察了4~6在30%H_2O_2催化氧化环己烯制备己二酸反应中的催化效果。实验结果表明:4b的催化效果最好。在最佳反应条件[环己烯20 mmol,4b 0.16 mmol,n(环己烯)∶n(H2O2)∶n(ILs)=1∶4.4∶0.008]下,己二酸产率71%。     

Pentafluorophenyl imidato palladium(II) complexes: catalysts for Suzuki cross-coupling reactions

Novel N-bonded imidato complexes of general formula [Pd(N-N)(C6F5)(imidate)](imidate = maleimidate, succinimidate or phthalimidate; N-N = 2,2'-bipyridine (bipy), 4,4'-dimethyl-2,2'-bipyridine (Me2bipy) or N,N,N',N'-tetramethylethylenediamine (tmeda)), [NBu4][Pd(C6F5)(H2O)(succinimidate)2] and [NBu4][Pd(C6F5)(L)(succinimidate)2](L = PPh3 or t-BuNC) have been synthesised. These complexes are air-, light- and moisture-stable. The crystal structures of [Pd(tmeda)(C6F5)(maleimidate)].H2O.0.5CHCl3, [NBu4][Pd(C6F5)(H2O)(succinimidate)2].H2O and [NBu4][Pd(C6F5)(t-BuNC)(succinimidate)2].2H2O have been determined by X-ray diffraction. Many of these new complexes are shown to be active phosphine-free palladium catalysts/precatalysts for the Suzuki cross-coupling reactions of aryl bromides and aryl chlorides with phenylboronic acid.     

双偶极半菁衍生物／H4SiW12O40自组装多层膜的研究

通过交替吸附H_4SiW_(12)O_(40)和双偶极半菁衍生物制备了一个新颖的无机- 有机杂化自组装多层膜。紫外可见光谱和X射线衍射研究证实了半菁衍生物 /H_4SiW_(12)O_(40)多层膜可被均匀沉积厚达至少12层，具有平均膜厚5.3nm(半菁 阳离子层加SiW_(12)O_(40)~(4-)层)的二维有序结构，膜中半菁衍生物与H_4SiW_ (12)O_(40)间发生了较强的电荷转移作用。循环伏安研究表明，薄膜具有较好的电 化学活性。     

STM image of tungstosilicic acid molecular layer on highly oriented pyrolytic graphite

Molecular layer of tungstosilicic acid (H4SiW12O40) deposited on freshly-cleaved highly oriented pyrolytic graphite (HOPG) was observed by scanning tunneling microscopy (STM) in air at room temperature.The molecular dimension (11.5 A) of H4SiWi2O4o measured by STM is consistent with known crystallographic parameter.We also imaged the boundary of H4SiW12O40 molecular layer on HOPG showing that molecular layer of H4SiW12O40 was formed.It has been proved that individual tungstosilicic acid species is imaged.The probable reason for the formation of the molecular layer is also discussed.     

Application of Heteropolyacid H4SiMo3W9O40 for the Preparation of Bimetallic MoWS2/Al2O3 Hydrotreatment Catalysts

Kinetics and Catalysis - The bimetallic MoWS2/Al2O3 catalyst was synthesized using the Keggin-type mixed heteropolyacid H4SiMo3W9O40. The monometallic catalysts SiMo12/Al2O3 and SiW12/Al2O3 based...     

A Novel Optical Complex between an Organic Substrate and a Polyoxometalate. Crystal and Molecular Structure of alpha-H(4)SiW(12)O(40).4HMPA.2H(2)O (HMPA = Hexamethylphosphoramide)

A solvated complex of alpha-H(4)SiW(12)O(40).4HMPA.2H(2)O composed the heteropolytungstate alpha-H(4)SiW(12)O(40) and the organic substrate hexamethylphosphoramide (HMPA) has been synthesised, purified, and characterized. The electronic spectra (lambda = 220-500 nm) as well as the (1)H NMR spectra for the title compound dissolved in CD(3)CN establish that this complex dissociates into free SiW(12)O(40)(4)(-) and HMPA moieties in solution unless the organic substrate HMPA is present in very high concentrations. The solid reflectance electronic spectra and IR spectra indicate that there is interaction between the alpha-H(4)SiW(12)O(40) and the organic substrate. The complex has no photosensitivity under irradiation of sunlight, but under the near-UV light result in a charge transfer by oxidation of the HMPA and the reduction of the polyoxometalate. Light yellow polyhedrons of the title compound crystallize from the aqueous solvent of acetonitrile and aqueous solution as the formula of alpha-H(4)SiW(12)O(40).4HMPA.2H(2)O in the monoclinic, space group P2(1). The unit cell has a = 12.791(3) ?, b = 22.103(6) ?, c = 15.532(4) ?, beta = 102.860(10) degrees, and Z = 2. From the bond-valence parameters, it was found that the four hydrogen atoms of the polyoxometalate were combined with the N atoms of the four HMPA respectively. The title compound shows a certain second-order and third-order nonlinear optical response of I(2)(omega) = 0.7I(2)(omega)(KDP) and chi((3)) = 2.63 x 10(-)(11) esu, respectively.     

硅钨杂多酸在中孔全硅分子筛HMS上的固载及其催化性能

用十二烷基胺代替传统的季铵盐合成了中孔全硅分子筛ＨＭＳ，并将硅钨杂多酸浸渍固载在ＨＭＳ上，用ＸＲＤ，ＦＴ－ＩＲ以及ＮＨ３－ＴＰＤ等手段对ＨＭＳ及不同负载量的焙烧温度的负载论剂进行了表征，即使在固载量为５０％的ＳｉＷ１２／ＨＭＳ中，ＳｉＷ１２仍保持其Ｋｅｇｇｉｎ结构产均匀分布在载体表面上，没有ＳｉＷ１２晶相生成，同时，在气－固相反应体系中研究了固载在ＨＭＳ上的ＳｉＷ１２在合成乙酸丁酯中的催化性能，实     

Hydrothermal Synthesis and Crystal Structure of a Polyoxometalate- based Complex [Cu^I（phen）2]4（SiW12O40）

A new hybrid polyoxometalate-based complex, [Cu^I（phen）214（SiW12O40） （phen = 1,10-phenanthroline）, has been synthesized by hydrothermal method and characterized with the aid of elemental analysis, IR, UV spectra and thermal analysis studies. The result of X-ray crystallography analysis exhibits that the title compound crystallizes in the orthorhombic space group P212121, and the formula is C96H64N16Cu4SiW12O40. Crystal data： a = 18.3574（14）, b = 21.1952（16）, c = 27.992（2）A, Mr = 4570.08, V = 10891.4（14）A^3, Z = 4, Dc = 2.787 g/cm^3,μ = 13.478 mm^-1, R = 0.0364, wR = 0.0638 （I 〉 2σ（I）） and F（000） = 8360. The complex consists of one α-Keggin anion [SIW12O40]^4- and four discrete [Cu^I（phen）2]^＋ cations. The valence sum calculations for the Cu atoms suggest that all four Cu atoms are in the ＋1 oxidation state.     

SiW12／Al2O3为前身态的加氢脱氮催化剂研究

本文制备了担载在Ａｌ２Ｏ３上的十二钨硅酸为前身态的加氢脱氮催化剂，用ＸＲＤ，ＩＲ表征了催化剂的表面结构，结果表明，在Ａｌ２Ｏ载体上，ＳｉＷ１２仍保持着其Ｋｅｇｇｉｎ结构并以高度分散状态存在。     

Si取代Keggin型多酸催化光解水产氢机理

本文采用DFT和TD-DFT方法研究了Keggin型多酸[SiW12O40]4-光催化劈裂水产氢气机理。计算结果显示反应主要包括四个步骤：(i) 光激发,(ii) 电荷转移和生成单电子还原(OER)中间体,(iii) 生成双电子还原(TER)中间体,(iv)氢气从多酸表面解离和催化剂重生。当第一个电子从甲醇转移到多酸后,后续反应存在均为热力学上有利的放热途径,并推动第二个电子从甲醇自由基,H[SiW12O40]4-或[SiW12O40]5-转移到OER中间体H[SiW12O40]4-或[SiW12O40]5-生成TER中间体[SiW12O40]6-,H[SiW12O40]5-或H2[SiW12O40]4-,并伴随着H2产生。耦合的电子和质子转移路径在能量上最有利。甲醇和水分子的参与有利于H2产生。多酸在整个催化循环中,扮演了光敏剂、催化剂、电子的受体和给体。     

铁-谷氨酸-硅钨酸三元配合物作为高活性非均相类Fenton催化剂降解4-氯酚

Fenton氧化法通过Fe2+离子催化分解H2O2产生羟基自由基,能够氧化降解绝大多数有机污染物.但是传统的均相Fenton氧化法使用高浓度二价铁盐作为催化剂,催化剂不便于回收利用,而且还会引发新的环境问题.另外,均相Fenton氧化法通常需要在pH约为3的酸性条件下进行,在较高pH条件下,有机物氧化降解速率降低,同时铁盐水解产生铁泥.文献报道了一些含铁固体材料作为非均相类Fenton催化剂,能够解决催化剂回收和重复利用问题,但是许多固体催化剂仍然只在酸性条件下表现出较高催化活性.多金属氧簇是除过渡金属氧化物之外的一类光催化剂.近年来,多金属氧簇在Fenton氧化过程中的应用开始受到关注.可以预计,含铁的多金属氧簇固体化合物有可能同时具有类Fenton催化活性和光催化活性.本文以三价铁盐(FeI I)、谷氨酸(Glu)和硅钨酸(SiW)为原料在水溶液中合成了一种不溶性的三元固体配合物FeШGluSiW,并用电感耦合等离子体原子发射光谱(ICP-AES)、热重分析(TG)、傅里叶变换红外光谱(FT-IR)、紫外-可见漫反射光谱(UV-vis DRS)、X射线衍射(XRD)和场发射扫描电镜(FE-SEM)对FeШGluSiW进行了表征.根据ICP-AES, TG和FT-IR结果推断, FeШGluSiW可能的化学组成为[Fe(C5H8NO4)(H2O)]2SiW12O40·13H2O,其中含有铁、谷氨酸根单元和Keggin结构的SiW12O404?阴离子. FE-SEM和XRD测试结果表明, FeШGluSiW是由结晶度较低、尺寸为100–200 nm的无规则颗粒组成,并含有无定形相.通过考察在自然初始pH 6.5条件下100 mg/L 4-氯酚(4-CP)在FeШGluSiW(1.0 g/L)/H2O2(20 mmol/L)体系中的氧化降解反应,我们发现在暗态和光照条件下,4-CP完全降解所需时间分别为40和15 min,延长反应时间至2 h,总有机碳(TOC)去除率分别达到27%和72%.结果表明, FeШGluSiW具有很高的催化活性,而且在光照条件下活性更高.进一步研究发现, FeШGluSiW在pH 3–6.5范围内均表现出高的催化活性,而且在酸性条件下活性更高.用ICP-AES测定Fe元素在溶液中的析出量,证实4-CP氧化降解主要发生在固体催化剂表面.在反应体系中加入正丁醇能显著抑制4-CP降解,说明4-CP降解反应涉及羟基自由基的氧化作用.在光照反应条件下,催化剂颜色明显变深,表明光照条件下的反应机理涉及催化剂中SiW12O404?阴离子的还原.考虑到催化剂中含有谷氨酸根和SiW12O404?杂多阴离子,推测H2O2有可能通过氢键吸附于催化剂表面,这可能是FeШGluSiW表现出高催化活性的重要原因.结合文献报道的含铁固体材料类Fenton催化机理和多金属氧簇光催化机理,可以很好地解释4-CP降解反应实验结果.在暗态条件下, FeШGluSiW的催化机理归因于催化剂表面FeII的氧化还原循环FeII?FeI,即H2O2分子在催化剂表面分解产生羟基自由基,从而导致4-CP氧化;而在光照条件下,除了催化剂中FeI I的类Fenton催化作用之外,催化剂中SiW12O404?杂多阴离子的光催化作用同时发生,导致4-CP降解速率加快.在光催化过程中,4-CP可以被激发态SiW12O404?直接氧化,也可以被激发态SiW12O404?与H2O相互作用产生的羟基自由基氧化.被还原的杂多阴离子可以被O2氧化,也可以被H2O2氧化,因而H2O2的存在也促进了FeШGluSiW的光催化作用.     

Mechanistic analysis of the electrocatalytic properties of dissolved alpha and beta isomers of [SiW12O40]4- and solid [Ru(bipy)3]2[alpha-SiW12O40] on the reduction of nitrite in acidic aqueous media

Voltammetric studies on the reduction of alpha and beta isomers of the Keggin polyoxometalate anion [SiW12O40]4- reveal a series of electrochemically reversible processes in acidic aqueous media. In the presence of NO2-, catalytic current is detected in the potential region of the [SiW12O40]4-/5- process. Electronic spectroscopy and simulation of voltammetric data undertaken at variable [NO2-] and [H+] allow the following mechanism to be postulated, [SiW12O40]4- + e- <-->[SiW12O40]5-, H+ + HNO2 <--> NO+ + H2O, NO+ + [SiW12O40]5- --> NO + [SiW12O40]4-. The second-order rate constant for the rate-determining step is faster for the alpha isomer than for the beta one. This may be attributed to the different reversible potentials of -0.144 V (alpha isomer) and -0.036 V vs Ag/AgCl (beta isomer) and, hence, smaller driving force for an assumed outer sphere electron-transfer reaction in the case of beta isomer. A stable, water-insoluble, thin-film [Ru(bipy)3]2[alpha-SiW12O40] chemically modified electrode was generated electrochemically via ion-exchange of [Ru(bipy)3]2+ with Bu4N+ in the [Bu4N]4[alpha-SiW12O40] solid. The first reduction process with this modified electrode gives rise to the reaction [Ru(bipy)3]2[alpha-SiW12O40](solid) + H+(soln) + e- <--> H[Ru(bipy)3]2[alpha-SiW12O40](solid). The need to transfer a proton from the solution to the solid phase for charge neutralization purposes introduces a hydrogen-ion concentration dependence into this reaction, which is not found in the solution-phase study. Nevertheless, the voltammetric catalytic activity with respect to nitrite reduction is retained with the chemically modified electrode. However, nitrite catalysis with the [Ru(bipy)3]2[alpha-SiW12O40]-modified electrode is now independent of concentration of H+, rather than exhibiting a first-order dependence, and full mechanistic details for this process are unknown.