Preparation of activated carbon from waste Camellia oleifera shell for supercapacitor application

The cost-effective activated carbons derived from waste Camellia oleifera shell (COS) by ZnCl₂ activation method are investigated as the active electrode material in electric double-layer capacitors (EDLCs) for the first time. The activation temperature and ZnCl₂/COS impregnation ratio are two key factors affecting the surface area and pore structure of the prepared activated carbons, which accordingly affect their capacitive performances. Electrochemical investigations indicate that the activated carbon (AC-3-600) obtained at the activation temperature of 600 °C and impregnation ratio of 3 shows the maximum specific capacitance of 374 and 266 F?g^?1 in 1 mol L^?1 H₂SO₄ and 6 mol L^?1 KOH electrolytes at 0.2 A g^?1, respectively. The high capacitance of the AC-3-600 is attributed to its high surface area (1,935 m² g^?1), high total pore volume (1.02 cm³ g^?1), and especially the large percentage of micropores (735 m² g^?1). Meanwhile, the activated carbon presents good cycle stability in both acid and alkaline electrolytes during 5,000 cycles at a fair current density of 4 A g^?1. So, we had reasons to believe that the activated carbons from waste COS by ZnCl₂ activation might be one of the innovative carbon electrode materials for EDLCs application.     

Converting eucalyptus leaves into mesoporous carbon for its application in quasi solid-state supercapacitors

A high performance activated carbon having pore diameter of 2.8 nm and specific surface area of 841.8 m² g^?1 is prepared by chemical activation of eucalyptus leaves using KOH as an activating agent. The chemically-treated eucalyptus leaves EL(T) as electrode material has a specific capacitance of 663.5 mF cm^?2 (equivalent to single electrode specific capacitance of 442.3 F g^?1) with solid polymer electrolyte. This active material has excellent rate capability and good cycle performance, over 95 % of the original capacitance is retained after 5,000 cycles. The energy density of 101.6 Wh kg^?1 and power density of 2.85 kW kg^?1 has been observed for EL(T) based quasi solid-state supercapacitors.     

Facile synthesis of biomass-derived hierarchical porous carbon microbeads for supercapacitors

Using the facile method of solvent evaporation, the leonardite fulvic acids (LFA)-based porous carbon microbeads (PCM) have been successfully prepared at ambient pressure, followed by carbonization and KOH activation (a low mass ratio alkali/LFA = 1.5) in an inert atmosphere. The effects of KOH treatment on pore structures and the formation mechanism of the PCM were discussed. The results showed that the sample exhibited remarkable improvement in textural properties. The activated carbon microbeads had high surface area (2269 m² g^?1), large pore volume (1.97 cm³ g^?1), and displayed excellent capacitive performances, compared with carbon powder. The porous carbon material electrodes with the “porous core structure” behaved superiorly at a specific capacitance of 320 F g^?1 at a current density of 0.05 A g^?1 in 6 M KOH electrolyte, which could still remain 193 F g^?1 when the current density increased to 100 A g^?1. Remarkably, in the 1 M TEABF₄/PC electrolyte, the PCM samples could reach 156 F g^?1 at 0.05 A g^?1, possess an outstanding energy density of 39.50 Wh kg^?1, and maintain at 22.05 Wh kg^?1 even when the power density rose up to 5880 W kg^?1. The balance of structural characteristic and high performance makes the porous carbon microbeads a competitive and promising supercapacitor electrode material.     

Nitric acid oxidation of ordered mesoporous carbons for use in electrochemical supercapacitors

Ordered mesoporous carbon materials with high microporosity were synthesized by a low temperature autoclaving of citric acid-catalyzed polymerized resorcinol/formaldehyde in the presence of the triblock copolymer F127 and were activated by nitric acid oxidation. The materials were used as electrode materials in electrochemical supercapacitors. A bimodal pore size distribution of 2.1–2.3 and 5.3 nm with a surface area of 465–578 m² g^?1 and pore volume of 0.44–0.54 cm³ g^?1 was obtained with the retention of an ordered mesoporous structure after nitric acid (2 M) treatment. The introduced functional groups produced a pseudocapacitance, which resulted in an increase in the specific capacitance. The electrochemical capacitance of the resulting mesoporous carbons showed a marked increase after 3 h of nitric acid activation, exhibiting a high value of 295 F g^?1 at the scan rate of 10 mV s^?1 in 6 M KOH aqueous solution and good cycling stability with specific capacitance retention over 500 cycles.     

Electrospun porous MnMoO<Subscript>4</Subscript> nanotubes as high-performance electrodes for asymmetric supercapacitors

MnMoO₄ nanotubes of diameter about 120 nm were successfully synthesized by a single-spinneret electrospinning technique followed by calcination in air, and their structural, morphological, and electrochemical properties were studied with the aim to fabricate high-performance supercapacitor devices. The obtained MnMoO₄ nanotubes display a 1D architecture with a porous structure and hollow interiors. Benefiting from intriguing structural features, the unique MnMoO₄ nanotube electrodes exhibit a high specific capacitance, excellent rate capability, and cycling stability. As an example, the tube-like MnMoO₄ delivers a specific capacitance of 620 F g^?1 at a current density of 1 A g^?1, and 460 F g^?1 even at a very high current density of 60 A g^?1. Remarkably, almost no decay in specific capacitance is found after continuous charge/discharge cycling for 10,000 cycles at 1 A g^?1. An asymmetric supercapacitor fabricated from this MnMoO₄ nanotubes and activated carbon displayed a maximum high energy density of 31.7 Wh kg^?1 and a power density of 797 W kg^?1, demonstrating a good prospect for practical applications in energy storage electronics.     

Pomegranate rind-derived activated carbon as electrode material for high-performance supercapacitors

In this paper, activated carbon materials were synthesized from pomegranate rind through carbonization and alkaline activation processes. The effects of pyrolytic temperature on the textual properties and electrochemical performance were investigated. The surface area of the activated carbon can reach at least 2200 m² g^?1 at different pyrolytic temperatures. It was found that, at the range of 600–900 °C, decreasing the carbonization temperature leads to the increase of t-plot micropore area, t-plot micropore volume, and capacitance. Further decreasing the carbonization temperature to 500 °C also leads to the increase of t-plot micropore area and t-plot micropore volume, but the capacitance is slightly poorer. The activated carbon carbonized at 600 °C and activated at 800 °C possesses very high specific area (2931 m² g^?1) and exhibits very high capacitance (～268 F g^?1 at 0.1 A g^?1 and ～242 F g^?1 at 1 A g^?1). There is no capacitance fading after 2000th cycle.     

The production of activated carbon from cation exchange resin for high-performance supercapacitor

High-performance activated carbon for electrochemical double-layer capacitors (EDLC) has been prepared from cation exchange resin by carbonization and subsequent activation with KOH. The activation temperature has a key role in the determination of porous carbon possessing high surface areas, and large pore structures. The porous carbon activated at 700 °C (carbon-700-1:4) has high surface area (2236 m²?g^?1) and large total pore volume (1.15 cm³?g^?1), which also displays best capacitive performances due to its well-balanced micro- or mesoporosity distribution. In details, specific capacitances of the carbon-700-1:4 sample are 336.5 F?g^?1 at a current density of 1 A?g^?1 and 331.8 F?g^?1 at 2 A?g^?1. At high current density as 20 A?g^?1, the retention of its specific capacitance is 68.4 %. The carbon-700-1:4 sample also exhibits high performance of energy density (46.7 Wh?kg^?1) and long cycle stability (～8.9 % loss after 3,000 cycles). More importantly, due to the amount of waste ion-exchange resins increasing all over the world, the present synthetic method might be adopted to dispose them, producing high-performance porous carbons for EDLC electrode materials.     

Facile preparation of nitrogen-doped porous carbon for high performance symmetric supercapacitor

In this work, the micromolecule l-glutamic acid (Glu) is employed as nitrogen-rich precursor to prepare a novel porous carbon, and ZnCl₂ is used as activating agent to improve the surface area and electrochemical performance of the carbon. The nitrogen content of the carbon (Glu-2.5) prepared by Glu and ZnCl₂ with a mass ratio of 1:2.5 retains as high as 7.1 % at an activation temperature of 700 °C. The surface area and pore volume of Glu-2.5 are 1007.4 m² g^?1 and 0.57 cm³ g^?1, respectively. Glu-2.5 exhibits a high specific capacitance of 330.6 F g^?1 in 2 M KOH electrolyte at the current density of 1 A g^?1and good cycling stability (89 % retention of capacitance after 5000 charge/discharge cycles). More importantly, the assembled symmetric supercapacitor using Glu-2.5 as electrodes reveals a high energy density (16.7 Wh kg^?1) under the power density of 404.7 W kg^?1. Owing to its inherent advantages, Glu-2.5 could be a promising and scalable alternative applied to energy storage/conversion.     

Synthesis of micro- and mesoporous carbon spheres for supercapacitor electrode

Micro- and mesoporous carbon spheres (MMCSs) are synthesized by the polymerization of colloidal silica-entrapped resorcinol/formaldehyde in the presence of ammonia as catalyst, followed by carbonization, sodium hydroxide (NaOH) etching to remove silica template, and potassium hydroxide (KOH) activation. The morphology and microstructure are characterized by scanning electron microscopy, transmission electron microscopy, and nitrogen adsorption–desorption. The results show that a typical sample (denoted as MMCS-3) unites the characteristics of regular spherical shape (uniform diameters of 500 nm), high specific surface area (1,620 m² g^?1), large pore volume (1.037 cm³ g^?1), and combined micropores and mesopores (11.0 nm), which endows MMCS-3 good electrochemical performance. MMCS-3 as supercapacitor electrode shows a specific capacitance of 314 F g^?1 under a current density of 0.5 A g^?1 and low internal resistance of 0.2 Ω in 6 M KOH aqueous solution. The electrochemical capacitance still retains 198 F g^?1 at a high current density of 10 A g^?1. After 500 cycle numbers of galvanostatic charge/discharge at 0.5 A g^?1, MMCS-3 electrode still remains the specific capacitance of 301 F g^?1 with the retention of 96 %. This study highlights the potential of well-designed MMCSs as electrodes for widespread supercapacitor applications.     

Ultrasonic-assisted synthesis of magnetite/carbon nanocomposite for electrochemical supercapacitor

Iron oxides are considered as the promising pseudocapacitive materials for high-performance supercapacitors due to their high theoretical specific capacitance, low cost, environmental benignity, and natural abundance. In this work, we study capacitive behavior of different magnetite (Fe₃O₄) nanoparticles/carbon black (CB) composites ratios. These composites are synthesized by the coprecipitation method in the presence of ultrasonic waves. The structural and morphological characteristics of the magnetite/CB composites are investigated by X-ray diffraction and scanning electron microscopy, respectively. The electrochemical performance of magnetite/CB composite electrodes is tested by cyclic voltammetry and galvanostatic charge/discharge in a Na₂SO₄ electrolyte. The results indicate that the magnetite/CB electrodes show typical pseudo-capacitive behavior in Na₂SO₄ solution. Moreover, in comparison to the pure Fe₃O₄ (37 F g^?1) and carbon black (23 F g^?1), the as-prepared 45 % magnetite/CB nanocomposite electrode shows a higher specific capacitance (300 F g^?1). Additionally, the supercapacitor device of the magnetite/CB nanocomposite exhibits excellent long cycle life along with 98.5 % specific capacitance retained after 10,000 cycle tests.     

Enhanced electrochemical performance of straw-based porous carbon fibers for supercapacitor

The efficient utilization of natural biomass as renewable raw materials is of importance. We herein prepared porous carbon fibers (PCFs) by activation of the extracted cellulose microfibers from the agriculture byproduct of corn straw. Different from the porous carbons (PCs) by directly activating straw, the obtained PCFs had typical one-dimensional morphology with high surface area (2013 m² g^?1) and large pore volume (1.27 cm³ g^?1). The influence of the ZnCl₂/cellulose mass ratio on the electrochemical performance was studied, and the optimized PCF(1:1) possessed a much higher specific capacitance than the PC(1:1) sample, which was attributed to the improved specific surface area as well as the fiber-like morphology where it had short ion diffusion route and small interfacial resistance in comparison to PCs. PCFs have a high specific capacitance of 230 F g^?1 at 0.5 A g^?1, and 183 F g^?1 was retained at 20 A g^?1 (79.6%), revealing an excellent rate capability. The assembled symmetrical supercapacitor exhibited a wide potential window of 1.8 V, small electrochemical impedance, and superior cycle performance. Moreover, a high energy density of 16.0 Wh kg^?1 was obtained at a power density of 450.4 W kg^?1, which was preserved of 6.9 Wh kg^?1 at a high power density of 14,194.3 W kg^?1.     

Binder-free activated carbon papers for high-performance electric double-layer capacitors

A binder-free activated carbon paper (ACP) was simply prepared for electric double-layer capacitors by the carbonization of filter paper, followed by heat-air activation at a lower temperature. The electrochemical cells assembled using the as-prepared ACP-470 provides a high specific capacitance of 296.4 F g^?1 at current density of 0.5 A g^?1 and a high rate performance at a current density of 150 A g^?1 with a capacitance of 191.2 F g^?1 and a high cycle ability at 10,000 recycles with 100 % capacitance retention. In addition, the ACP has a lower electrical resistivity and provides an effective energy storage performance with a maximum energy density of 41.2 Wh kg^?1 and a maximum power density of 138.0 kW kg^?1 in a voltage range of 1 V.     

KOH direct treatment of kombucha and in situ activation to prepare hierarchical porous carbon for high-performance supercapacitor electrodes

Kombucha, a renewable biomass, has been successfully utilized as an accessible carbon source to fabricate kombucha-derived hierarchical porous carbon (KHPC) by KOH direct treatment and in situ activation. The prepared KHPC shows an interconnected hierarchical porous structure, a pore volume of 0.41 cm³ g^?1, and a specific surface area of 917 m² g^?1. Due to the multiple synergistic effects of these advantages, the KHPC-3 exhibits a high specific capacitance of 326 F g^?1 at a current density of 1 A g^?1 in 6 M KOH, good rate capability of 82% retention from 1 to 20 A g^?1, and cycling performance with 91.3% retention over 5000 cycles. Moreover, the KHPC-3 symmetric supercapacitor reveals a good energy density of 20.97 Wh kg^?1 at a power density of 871.2 W kg^?1 and retains 8.08 Wh kg^?1 at 6330 W kg^?1 in 1 M Na₂SO₄ electrolyte. Therefore, the KHPC obtained via the simple synthesis process shows great promise as an electrode material in energy storage devices.     

A high-performance hybrid supercapacitor with Li4Ti5O12-C nano-composite prepared by in situ and ex situ carbon modification

In this work, we report on the synthesis of in situ and ex situ carbon-modified Li₄Ti₅O₁₂-C (LTO-C) nano-composite and its application in a hybrid supercapacitor constructed using activated carbon (AC) and LTO-C nano-composite as positive and negative electrodes, respectively. The hybrid capacitors are characterized by galvanostatic charge–discharge, cycle life testing, and electrochemical impedance spectroscopy. The results reveal that the AC/LTO-C hybrid capacitors exhibit high rate capability and long cycle life. In the potential range of 1.5–3.0 V, the AC/LTO-C hybrid system can deliver a specific capacitance of 83 F?g^?1 based on the total mass of AC and LTO-C electrodes at a current density of 60 mA g^?1 (2 C rate). At a higher discharge rate of 980 mA g^?1 (32 C), the capacity is 68 F?g^?1, about 82?% of that at 2 C rate. After 9,000 deep cycles at 32 C, the hybrid capacitor still maintains 84?% of its initial capacitance. The specific energy of such hybrid system is 20 Wh kg^?1, which is at least twice that of an AC/AC system. Combining the high energy density with power capability, the AC/LTO-C hybrid supercapacitor has demonstrated high performance for applications needing high power output.     

Dual template method to prepare hierarchical porous carbon nanofibers for high-power supercapacitors

Hierarchical porous carbon nanofibers serving as electrode materials are prepared through carbonization and hydrofluoric acid treatment of polyacrylonitrile-based electrospinning involving dual templates. The hierarchical porous structures are synergistically tailored by varying template contents in the spinning solution. The carbon nanofibers prepared from the electrospinning of polyacrylonitrile containing 15/15 wt.% polymethylmethacrylate/tetraethyl orthosilicate exhibit the largest specific surface area (699 m² g^?1) and microporous volume (0.196 cm³ g^?1). In 6 M KOH electrolyte, a symmetrical supercapacitor equipped with the hierarchical porous carbon nanofibers demonstrates its high-end specific capacitance of 170 F g^?1, superior rate capability, and high-power density output up to 14.7 kW kg^?1. Cycling evolution indicates capacitance fading is only 5.8 % of initial capacitance at a current density of 1 A g^?1 even after 8,000 cycles. The excellent electrochemical performances of the carbon nanofiber are mainly ascribed to the optimized pore size distributions of both micropores and mesopores and the unique hierarchical pore structures possessed by abundant micropores.     

A tunable hierarchical porous carbon from starch pretreated by calcium acetate for high performance supercapacitors

Hierarchical porous carbons (HPCs) with abundant mesopores have been prepared by a facile route from the starch that was pretreated by calcium acetate. The scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and N₂ adsorption–desorption tests show that hierarchical porous carbons with bimodal mesopores have been obtained. Moreover, the pore sizes are tunable by simply adjusting the reactants ratio and carbonization temperature. The as-synthesized hierarchical porous carbon materials (HPCs-2-800) possesses the highest Brunauer-Emmett-Teller (BET)-specific surface area of 464 m² g^?1 and mesoporous volume of 0.663 cm³ g^?1 at the carbonization temperature of 800 °C and starch to calcium acetate mass ratio of 2. Electrochemical measurements also display that the HPCs-2-800 electrodes have a high reversible capacity of 244 F g^?1 at the current density of 0.1 A g^?1 and 182 F g^?1 at the current density of 10 A g^?1. When the current density is elevated from 0.1 to 10 A g^?1, the high capacitance retention of 74.6 % reveals a good rate performance. Long charge–discharge cycling measurements disclose good stabilities over 25,000 cycles at different current densities of 1–10 A g^?1 (5000 cycles at each current density) for HPCs-2-800 electrode. The cycling results indicate a high capacitance retention of 99.6 % over 5000 charge–discharge cycles even at the current density of 10 A g^?1. The excellent supercapacitive performances imply that HPCs-2-800 is a promising candidate for supercapacitors.     

Hierarchical mesoporous carbon materials: preparation by direct tri-constituent co-assembly and the electrochemical performance

Hierarchical mesoporous carbon materials with large microporosity were prepared by direct tri-constituent co-assembly with the use of resols as the carbon precursor, tetraethyl orthosilicate as the inorganic precursor, and triblock copolymer F127 as the soft template. Bimodal pore size distributions in the range of 1.5–4 and 7.5–12 nm were obtained in the synthesized hierarchical mesoporous carbon materials after etching of silica by HF acid, showing a high surface area of 1,675 m²?g^?1 with a large pore volume of 2.06 cm³?g^?1. The electrochemical performance of the hierarchical mesoporous carbons was evaluated as an electrode material for electrochemical supercapacitor, showing a specific capacitance as high as 152 F?g^?1 at a scan rate of 5 mV?s^?1 in 6 M KOH aqueous solution and a good cycling stability with capacitance retention of 99 % over 500 cycles.     

Facile fabrication of mesoporous manganese oxides as advanced electrode materials for supercapacitors

Mesoporous manganese oxides (MnO₂) were synthesized via a facile chemical deposition strategy. Three kinds of basic precipitants including sodium carbonate (Na₂CO₃), sodium bicarbonate (NaHCO₃), and sodium hydroxide (NaOH) were employed to adjust the microstructures and surface morphologies of MnO₂ materials. The obtained MnO₂ materials display different microstructures. Great differences are observed in their specific surface area and porosity properties. The microstructures and surface morphologies characteristics of MnO₂ materials largely determine their pseudocapacitive behavior for supercapacitors. The MnO₂ prepared with Na₂CO₃ precipitant exhibits the optimal microstructures and surface morphologies compared with the other two samples, contributing to their best electrochemical performances for supercapacitors when conducted either in the single electrode tests or in the capacitor measurements. The optimal MnO₂ electrode exhibits a high specific capacitance (173 F g^–1 at 0.25 A g^?1), high-rate capability (123 F g^?1 at 4 A g^?1), and excellent cyclic stability (no capacitance loss after 5,000 cycles at 1 A g^?1). The optimal activated carbon//MnO₂ hybrid capacitor exhibits a wide working voltage (1.8 V), high-power and high-energy densities (1,734 W kg^?1 and 20.9 Wh kg^?1), and excellent cycling behavior (93.8 % capacitance retention after 10,000 cycles at 1 A g^?1), indicating the promising applications of the easily fabricated mesoporous MnO₂ for supercapacitors.     

Hybrid materials utilizing polyelectrolyte-derivatized carbon nanotubes and vanadium-mixed addenda heteropolytungstate for efficient electrochemical charging and electrocatalysis

Preparation and electrochemical behavior of new hybrid materials composed of multi-walled carbon nanotubes (CNTs) that were derivatized with poly(diallyldimethylammonium) chloride and modified with vanadium-mixed addenda Dawson-type heteropolytungstate, [P₂W₁₇VO₆₂]^8?, is described here. These nanostructured composite systems exhibited fast dynamics of charge propagation. They were characterized by the transport (effectively diffusional) kinetic parameter of approximately 8?×?10^?8 cm^?2 s^?1/2 and the specific capacitance parameter of 82 F g^?1 (at the charging/discharging current of 200 mA g^?1). The latter parameter for bare CNTs was found to be only 50 F g^?1 under analogous conditions. These observations were based on the results of galvanostatic charging–discharging, cyclic voltammetric, and AC impedance spectroscopic measurements. The improved capacitance properties were attributed to the systems’ pseudocapacitive features originating from the fast redox transitions of the [P₂W₁₇VO₆₂]^8? polyanions. In addition to the fast redox conduction, the proposed organic–inorganic hybrid materials exhibited interesting electrocatalytic activity toward reduction of bromate in the broad concentration range (sensitivity, 0.24 mA cm^?2 mmol^?1 dm³).     

Fabrication and characterization of electrochemical double layer capacitors using ionic liquid-based gel polymer electrolyte with chemically treated activated charcoal electrodes

The present investigation deals with electrochemical double layer capacitors (EDLCs) made up of ionic liquid (IL)-based gel polymer electrolytes with chemically treated activated charcoal electrodes. The gel polymer electrolyte comprising of poly(vinylidine fluoride-co-hexafluropropylene) (PVdF-HFP)–1-ethyl-2,3-dimethyl-imidazolium-tetrafluroborate [EDiMIM][BF₄]–propylene carbonate (PC)–magnesium perchlorate (Mg(ClO₄)₂) exhibits the highest ionic conductivity of ~8.4?×?10^?3?S?cm^?1 at room temperature (~20 °C), showing good mechanical and dimensional stability, suitable for their application in EDLCs. Activation of charcoal was done by impregnation method using potassium hydroxide (KOH) as activating agent. Brunauer–Emmett–Teller (BET) studies reveal that the effective surface area of treated activated charcoal powder (1,515 m²?g^?1) increases by more than double-fold compared to the untreated one (721 m²?g^?1). Performance of EDLCs has been tested using cyclic voltammetry, impedance spectroscopy, and charge–discharge techniques. Analysis shows that chemically treated activated charcoal electrodes have almost triple times more capacitance values as compared to the untreated one.