Intersubband transitions in InAs/GaSb semi-metallic superlattices

Magnetic field orientated parallel to the superlattice layers enables intersubband absorption to occur for normally incident light. We investigate semi-metallic InAs/GaSb superlattices in this configuration, presenting data over a wide range of InAs well widths. For narrow wells, the reduced absorption coefficient means that an alternative waveguide configuration, where the light makes about 4 or 5 passes through the sample is used. In this second configuration we see further activation of the intersubband resonance by the parallel field. The intersubband energy and absorption characteristics are studied over a large range of well widths and compared with results from 8-band k·p calculations.     

Coherent phonon dynamics in short-period InAs/GaSb superlattices

We have performed ultrafast pump-probe spectroscopy studies on a series of InAs/GaSb-based short-period superlattice (SL) samples with periods ranging from 46 Å to 71 Å. We observe two types of oscillations in the differential reflectivity with fast (∼$\sim$1–2 ps) and slow (∼$\sim$24 ps) periods. The period of the fast oscillations changes with the SL period and can be explained as coherent acoustic phonons generated from carriers photoexcited within the SL. This mode provides an alternative method for determining the SL period. The period of the slow mode depends on the wavelength of the probe pulse and can be understood as a propagating coherent phonon wavepacket modulating the reflectivity of the probe pulse as it travels from the surface into the sample.     

Four-component superlattice empirical pseudopotential method for InAs/GaSb superlattices

For the design of InAs/GaSb superlattice (SL) heterojunction infrared photodetectors with very low dark current we have extended the standard two-component superlattice empirical pseudopotential method (SEPM) and implemented a four-component model including interface layers. For both models, the calculated bandgap values for a set of SL samples are compared to bandgaps determined by photoluminescence measurements. While the bandgap resulting from the two-component model agrees well with experimental data for SL structures with individual layer thicknesses of 7 monolayers and more, we show that for SLs with thinner GaSb layers the four-component SEPM model is accurate, when the As-content in the interface and barrier layers is included in the model.     

InAs/GaSb量子阱的能带结构及光吸收

采用八能带K-P理论以及有限差分方法,研究了沿[001]方向生长的InAs/GaSb二类断带量子阱体系的能带结构、波函数分布和对[110]方向线性偏振光的吸收特性.研究发现,通过改变InAs或GaSb层的厚度,可有效调节该量子阱体系的能带结构及波函数分布.计算结果表明,当InAs/GaSb量子阱的导带底与价带顶处于共振状态时,导带基态与轻空穴基态杂化效应很小,且导带基态与第一激发态的波函数存在较大的重叠,导带基态与第一激发态之间在布里渊区中心处的跃迁概率明显大于导带底与价带顶处于非共振状态时的跃迁概率.研究结果对基于InAs/GaSb二类断带量子阱体系的中远红外波段的新型级联激光器、探测器等光电器件的设计具有重要意义.     

Performance of dual-band short-or mid-wavelength infrared photodetectors based on InGaAsSb bulk materials and InAs/GaSb superlattices

In this paper,we demonstrate bias-selectable dual-band short-or mid-wavelength infrared photodetectors based on In_(0.24)Ga_(0.76)As_(0.21)Sb_(0.79)bulk materials and InAs/GaSb type-II superlattices with cutoff wavelengths of 2.2μm and 3.6μm,respectively.At 200 K,the short-wave channel exhibits a peak quantum efficiency of 42%and a dark current density of5.93×10~(-5)A/cm~2at 500 mV,thereby providing a detectivity of 1.55×10~(11)cm·Hz~(1/2)/W.The mid-wave channel exhibits a peak quantum efficiency of 31%and a dark current density of 1.22×10~(-3)A/cm~2at-300 mV,thereby resulting in a detectivity of 2.71×10~(10)cm·Hz~(1/2)/W.Moreover,we discuss the band alignment and spectral cross-talk of the dual-band n-i-p-p-i-n structure.     

Mini-gaps and novel giant negative magnetoresistance in InAs/GaSb semimetallic superlattices

We have studied the temperature dependence of the magnetoresistance of semimetallic InAs/GaSb structures with magnetic field applied parallel to the layers. We present the first unambiguous evidence for the presence of a mini-gap at the crossing point between the electron and hole dispersion relations. The resistivity is found to change from semiconductor-like behaviour with a strong temperature dependence at low parallel magnetic fields to that of a semimetal with a weak temperature dependence at high field. Furthermore, the magnetoresistance, for intrinsic samples, is found to decrease with field by as much as 70% at low temperatures. As the parallel magnetic field is increased the centres of the electron and hole dispersions are shifted apart in k-space and at sufficiently high field the mini-gap is destroyed and the bands overlap fully. Finally, a theoretical model allows us to estimate that the mini-gap is of order 7 meV.     

Interfaces as design tools for short-period InAs/GaSb type-II superlattices for mid-infrared detectors

The effect of interface anisotropy on the electronic structure of InAs/GaSb type-II superlattices is exploited in the design of thin-layer superlattices for mid-IR detection threshold. The design is based on a theoretical envelope function model that incorporates the change of anion and cation species across InAs/GaSb interfaces, in particular, across the preferred InSb interface. The model predicts that a given threshold can be reached for a range of superlattice periods with InAs and GaSb layers as thin as a few monolayers. Although the oscillator strengths are predicted to be larger for thinner period superlattices, the absorption coefficients are comparable because of the compensating effect of larger band widths. However, larger intervalence band separations for thinner-period samples should lead to longer minority electron Auger lifetimes and higher operating temperatures in p-type SLs. In addition, the hole masses for thinner-period samples are on the order the free-electron mass rather than being effectively infinite for the wider period samples. Therefore, holes should also contribute to photoresponse. A number of superlattices with periods ranging from 50.6 to 21.2 Å for the 4 μm detection threshold were grown by molecular beam epitaxy based on the model design. Low temperature photoluminescence and photoresponse spectra confirmed that the superlattice band gaps remained constant at 330 meV although the period changed by the factor of 2.5. Overall, the present study points to the importance of interfaces as a tool in the design and growth of thin superlattices for mid-IR detectors for room temperature operation.     

Growth and electrical characterization of type II InAs/GaSb superlattices for midwave infrared detection

Herein, we report a type II InAs/GaSb superlattice structure (SLS) grown on GaSb(1 0 0) substrates by molecular beam epitaxy (MBE) and its electrical characterization for mid-wavelength infrared detection. A GaSb buffer layer was grown under optimized SLS growth conditions, which can decrease the occurrence of defects for similar pyramidal structures. The complications associated with these conditions include oxide desorption of the substrate, growth temperature of the SLS, the V/III ratio during superlattice growth and the shutter sequence. High-resolution X-ray diffraction (HRXRD) shows the sixth satellite peak, and the period of the SLS was 52.9 Å. The atomic force microscopy (AFM) images indicated that the roughness was less than 2.8 nm. High-resolution transmission electron microscopy (HRTEM) images indicated that the SLS contains few structural defects related to interface dislocations or strain relaxation during the growth of the superlattice layer. The photoresponse spectra indicated that the cutoff wavelength was 4.8 μm at 300 K. The SLS photodiode surface was passivated by a zinc sulfide (ZnS) coating after anodic sulfide.     

High quality mid-wavelength infrared InAs/GaSb superlattices by exploring the optimum molecular beam epitaxy growth process

In this paper we report on the growth of mid-wavelength infrared superlattice materials by molecular beam epitaxy. We focused on the effects of process parameters, such as arsenic beam equivalent pressure and shutter sequences, on the key material properties, such as the lattice mismatch and the surface morphology. Though a smaller As beam equivalent pressure helps to reduce the lattice mismatch between the superlattice and the GaSb substrate, the As beam equivalent pressure itself has a lower limit below which the material’s surface morphology will degrade. To achieve fully lattice-matched superlattice materials, a novel shutter sequence in the growth process was designed. With well-designed interface structures, a high quality P-I-N superlattice mid-infrared detector structure was realized. At 77 K the dark current density at −50 mV bias was 2.4 × 10⁻⁸ A/cm² and the resistance-area product (RA) at maximum (−50 mV bias) was 2.4 × 10⁶ Ω cm², and the peak detectivity was then calculated to be 9.0 × 10¹² cm Hz^1/2/W. The background limited infrared photodetector (BLIP) level can be achieved at a temperature of 113 K.     

Excess noise in InAs/GaSb type-II superlattice pin-photodiodes

We characterize the low-frequency white noise behavior of a large set of InAs/GaSb superlattice infrared pin-photodiodes for the mid-wavelength infrared regime at 3–5 μm. For diodes with an increased dark current in comparison to the dark current of generation–recombination limited bulk material, the standard shot-noise model fails to describe the noise experimentally observed in the white part of the spectrum. Instead, we find that McIntyre’s noise model for avalanche multiplication processes is compliant with our data. We suggest that within high electric field domains localized around macroscopic defects, avalanche multiplication processes leading to increased dark current and excess noise.     

第一原理研究界面弛豫对InAs/GaSb超晶格界面结构、能带结构和光学性质的影响

通过广义梯度近似的第一原理全电子相对论计算, 研究了不同界面类型InAs/GaSb超晶格的界面结构、电子和光吸收特性. 由于四原子界面的复杂性和低对称性, 通过对InAs/GaSb超晶格进行电子总能量和应力最小化来确定弛豫界面的结构参数. 计算了InSb, GaAs型界面和非特殊界面(二者交替)超晶格的能带结构和光吸收谱, 考察了超晶格界面层原子发生弛豫的影响.为了证实能带结构的计算结果, 用局域密度近似和Hartree-Fock泛函的平面波方法进行了计算. 对不同界面类型InAs/GaSb超晶格的能带结构计算结果进行了比较, 发现界面Sb原子的化学键和离子性对InAs/GaSb超晶格的界面结构、 能带结构和光学特性起着至关重要的作用.     

Passivation techniques for InAs/GaSb strained layer superlattice detectors

InAs/(In,Ga)Sb Strained Layer Superlattices (SLSs) have made significant progress since they were first proposed as an infrared (IR) sensing material more than three decades ago. The basic material properties of SLS provide a prospective benefit in the realization of IR imagers with suppressed interband tunneling and Auger recombination processes, as well as high quantum efficiency and responsivity. With scaling of single pixel dimensions, the performance of focal plane arrays is strongly dependent on surface effects due to the large pixels’ surface/volume ratio. This article discusses the cause of surface leakage currents and various approaches of their reduction including dielectric passivation, passivation with organic materials (polyimide or various photoresists), passivation by overgrowth of wider bandgap material, and chalcogenide passivation. Performance of SLS detectors passivated by different techniques and operating in various regions of infrared spectrum has been compared.     

InAs/GaSb量子阱中太赫兹光电导特性

太赫兹技术由于具有重大的科学价值及应用前景而引起了广泛关注,其核心问题是性能优异的室温太赫兹辐射源和探测器研究.本文用半经典的玻尔兹曼方程方法研究了In As/Ga Sb量子阱系统中载流子对电磁场的响应,运用平衡方程方法求解玻尔兹曼方程得到了量子阱系统中的光电导,系统地研究了量子阱结构对光电导的影响,揭示了在该量子阱系统中光电导产生的物理机制.研究发现,量子阱结构主要通过调节载流子的能级、浓度和波函数的耦合影响光电导,对称性较好的量子阱结构(8 nm-8 nm)的光电导信号更强,其峰值落在太赫兹区(0.2 THz),并且在低温下器件的性能较好,温度升高则吸收峰略有降低,且光电导峰值发生红移.研究结果表明该量子阱系统可以用作室温太赫兹光电器件.     

Interface effect on superlattice quality and optical properties of InAs/GaSb type-II superlattices grown by molecular beam epitaxy

We systematically investigate the influence of InSb interface (IF) engineering on the crystal quality and optical properties of strain-balanced InAs/GaSb type-II superlattices (T2SLs). The type-II superlattice structure is 120 periods InAs (8 ML)/GaSb (6 ML) with different thicknesses of InSb interface grown by molecular beam epitaxy (MBE). The high-resolution x-ray diffraction (XRD) curves display sharp satellite peaks, and the narrow full width at half maximum (FWHM) of the 0th is only 30-39 arcsec. From high-resolution cross-sectional transmission electron microscopy (HRTEM) characterization, the InSb heterointerfaces and the clear spatial separation between the InAs and GaSb layers can be more intuitively distinguished. As the InSb interface thickness increases, the compressive strain increases, and the surface "bright spots" appear to be more apparent from the atomic force microscopy (AFM) results. Also, photoluminescence (PL) measurements verify that, with the increase in the strain, the bandgap of the superlattice narrows. By optimizing the InSb interface, a high-quality crystal with a well-defined surface and interface is obtained with a PL wavelength of 4.78 μ, which can be used for mid-wave infrared (MWIR) detection.     

Field induced interlayer interband coupled states in aperiodic InAs/GaSb heterostructures

The interlayer interband state coupling and the interfacial composition effect in aperiodic InAs/GaSb (001) heterostructures are studied with the scattering theoretic Green's function technique, which can handle interlayer multi-subband interaction under the external bias. The current density calculation shows that the interlayer interband coupled subbands enhance the peak current density by facilitating electron resonant tunneling. The calculated spectral local density of states of a heterostructure predicts that the GaAs interface shifts the energies of the quasibound states to lower energies than those of the InSb interface case, which agrees with experimental results.     

Quantum spin Hall effect in inverted InAs/GaSb quantum wells

We review the recent experimental progress towards observing quantum spin Hall effect in inverted InAs/GaSb quantum wells (QWs). Low temperature transport measurements in the hybridization gap show bulk conductivity of a non-trivial origin, while the length and width dependence of conductance in this regime show strong evidence for the existence of helical edge modes proposed by Liu et al. [Phys. Rev. Lett., 2008, 100: 236601]. Surprisingly, edge modes persist in spite of comparable bulk conduction and show only weak dependence on magnetic field. We elucidate that seeming independence of edge on bulk transport comes due to the disparity in Fermi-wave vectors between the bulk and the edge, leading to a total internal reflection of the edge modes.     

Influence of the p-type doping on the radiometric performances of MWIR InAs/GaSb superlattice photodiodes

In this paper, quantum efficiency (QE) measurements performed on type-II InAs/GaSb superlattice (T2SL) photodiodes operating in the mid-wavelength infrared domain, are reported. Several comparisons were made in order to determine the SL structure showing optimum radiometric performances: same InAs-rich SL structure with different active zone thicknesses (from 0.5 μm to 4 μm) and different active zone doping (n-type versus p-type), same 1 μm thick p-type active zone doping with different SL designs (InAs-rich versus GaSb-rich and symmetric SL structures). Best result was obtained for the p-type doped InAs-rich SL photodiode, with a 4 μm active zone thickness, showing a QE that reaches 61% at λ = 2 μm and 0 V bias voltage.     

Mid-wavelength type II InAs/GaSb superlattice infrared focal plane arrays

We have demonstrated 384 × 288 pixels mid-wavelength infrared focal plane arrays (FPA) using type II InAs/GaSb superlattice (T2SL) photodetectors with pitch of 25 μm. Two p-i-n T2SL samples were grown by molecular beam epitaxy with both GaAs-like and InSb-like interface. The diode chips were realized by pixel isolation with both dry etching and wet etching method, and passivation with SiN_x layer. The device one with 50% cutoff wavelength of 4.1 μm shows NETD ∼ 18 mK from 77 K to 100 K. The NETD of the other device with 50% cutoff wavelength at 5.6 μm is 10 mK at 77 K. Finally, the T2SL FPA shows high quality imaging capability at the temperature ranging from 80 K to 100 K which demonstrates the devices’ good temperature performance.     

Type-II InAs/GaSb superlattices for very long wavelength infrared detectors

Type-II superlattices (SLs) can be designed for semiconductor band gaps as large as 400 meV down to semimetallic. This flexibility in design makes them an excellent candidate for infrared photodiodes with cut-off wavelengths beyond 15 μm. There are relatively few options for high-performance infrared detectors to cover wavelengths longer than 15 μm, especially for operating temperatures above 15 K. In the past few years, excellent results have been obtained on photoconductive and photodiode samples designed for infrared detection in the very long wavelength infrared (VLWIR) range (λ>15 μm). There is a variety of possible designs for these SLs which will produce the same narrow band gap by adjusting individual layer thicknesses, or indium content, in the InGaSb layer. Several of these different design options have been grown and characterized. These designs often require monolayer control per layer over hundreds of repeats in the SL. Photoresponse spectra for type-II SLs are compared to show how the design choices not only change the band gap but also the band structure, as reflected in features observed in the spectra. Theoretical modeling results are used to interpret the photoresponse spectra. SLs with cut-off wavelengths ranging from 15 to 25 μm are covered.