Simultaneous determination of neodymium and erbium in rare earth mixture with 5,7-dibromo-8-hydroxyquinoline and TX-100 by third-derivative spectrophotometry

The absorption spectra of 4f electron transitions of the complexes of neodymium and erbium with 5,7-dibromo-8-hydroxyquinoline in the presence of octylphenol poly(ethyleneglycol)ether have been studied by normal and third-derivative spectrophotometry. The proposed method is free of interference of other rare earths. The calibration graphs were linear up to 18 g/ml of neodymium and 21 g/ml of erbium (in the final solution). The derivative molar absorptivities are 395 l.mol^–1.cm^–1 for neodymium and 3421.mol^–1.cm^–1 for erbium. The corresponding values of Sandell's sensitivity were 0.36 and 0.49 g.cm^–1, respectively. The relative standard deviations evaluated from ten independent determinations of 2.5 g/ml of neodymium and erbium are 1.5 and 3.8% for neodymium and 1.8 and 4.1% for erbium in absence and presence of 70 g of lanthanum, respectively. The detection limits (signal to noise ratio=2) are 0.23 g/ml for neodymium and 0.30 g/ml for erbium. The method has been used for the determination of neodymium and erbium in mixed rare earths with satisfactory results.     

Development and Validation of an HPTLC–Densitometric Method for Determination of ACE Inhibitors

A high-performance thin layer chromatographic method coupled with densitometric analysis has been developed for measurement of benazepril and cilazapril, both pure and in their commercial dosage forms. The active substances were extracted from tablets with methanol (mean recovery 102%) and chromatographed on silica gel 60 F₂₅₄ HPTLC plates in horizontal chambers with ethyl acetate–acetone–acetic acid–water, 8:2:0.5:0.5 (v/v), as mobile phase. Chromatographic separation of these ACE inhibitors was followed by UV densitometric quantitation at 215 nm. Calibration plots were constructed in the range 0.4 to 2.0 g L^–1 for benazepril (2.0–10.0 g spot^–1) and from 0.5 to 1.5 g L^–1 for cilazapril (4.0–12.0 g spot^–1) with good correlation coefficients (r 0.990). The method was used to determine benazepril and cilazapril in pharmaceutical preparations with satisfactory precision (1.4% < RSD < 5.6%) and accuracy (1.7 < RE < 5.1).     

A toxic reagent-free method for normal-phase matrix solid-phase dispersion extraction and reversed-phase liquid chromatographic determination of aldrin,dieldrin, and DDTs in animal fats

A method for the determination of aldrin, dieldrin, DDT, DDE, and DDD contamination in animal fats (beef tallow, lard, and chicken fat) without using toxic reagents is developed, that uses high-performance liquid chromatography after the sample has been prepared by matrix solid-phase dispersion (MSPD) with acidic alumina oxide. A reversed-phase C₁-silica column with a mobile phase of 50% (v/v) ethanol solution (in water) and a photo-diode array detector were used for the determination. Average recoveries of the target compounds (0.2–5.0 g g^–1) ranged from 84–98%, with coefficients of variation of <5%. The limits of quantitation were 0.16 g g^–1 for AD, 0.10 g g^–1 for DD, 0.06 g g^–1 for DDT, 0.07 g g^–1 for DDE, and 0.05 g g^–1 for DDD. No toxic reagents were used at all.     

Multi-residue procedure for the analysis of pesticides in groundwater: Application to samples from the comunidad Valenciana,Spain

Summary A simple multi-residue procedure has been developed and applied to the analysis of pesticides in groundwater samples from the Comunidad Valenciana, a predominantly agricultural area on the Mediterranean coast of Spain. The procedure includes a liquid-liquid extraction, after addition of NaCl on the samples, and a subsequent analysis by capillary gas chromatography using a dual detection system with electron capture and nitrogen-phosphorous detectors. This allows the determination of more than 30 compounds (organophosphorous, organochlorine and pyrethroid pesticides) at the low ppb (g l^–1) levels. Detection limits obtained varied between 0.01 g l^–1 (lindane, fonofos) and 0.5 g l^–1 (cypermethrin). An additional injection of the sample extracts into a gas chromatograph equipped with a column of different polarity and electron capture detector is used for the confirmation of chromatographic peaks. The recommended procedure has been applied to 66 ground water samples. Pesticides, including organophosphorus and organochlorine compounds were detected in 31 of them, in levels ranging from 0.02 to 0.7 g l^–1.     

Depth profile studies of ZrTiN coatings by laser ablation inductively coupled plasma mass spectrometry

The feasibility of depth profiling was studied by using a 193-nm ArF* excimer laser ablation system (GeoLas, MicroLas, Goettingen, Germany) with a lens array-based beam homogenizer in combination with an ICP-QMS Agilent 7500. Two ablation cells (20 and 1.5 cm³) were compared at the laser repetition rate of 1 Hz, laser beam energy of 135 mJ and the carrier gas flow rate 1.5 L min^–1 He + 0.78 L min^–1 Ar. The ablation cell dimensions are important parameters for signal tailing; however, very small cell volumes (e.g. 1.5 cm³) may cause memory effects, which can be probably explained by dominant inertial losses of aerosol on cell walls with its delayed mobilization. The 20-cm³ ablation cell seems to be appropriate for depth profiling by continuous single-hole drilling. The study of the influence of the pit diameter magnitude on the waning and emerging signals under small crater depth/diameter aspect ratios, which range between 0.75 and 0.0375 for the 3-m-thick coatings and pit diameters 4–80 m, revealed that the steady-state signals of pure coating and pure substrate (out of interface) were obtained at crater diameters between 20 and 40 m. Depth resolution defined by means of slopes of tangents in the layer interface region depend on the pit diameter and has an optimum value between 20 and 40 m and gives 0.6 m for the 20-m pit. In-depth variation of concentration of coating constituent (Ti) was proved to be almost identical with two different laser/ICP systems.Viktor Kanický performed this work while on leave at ETH Zurich     

Simultaneous capillary GC-MS determination of triazines and amides in water

Summary A simultaneous capillary Gas Chromatographic-Mass Spectrometric (GC-MS) method is described for the determination of thirteen pesticides belonging to the triazine and amide families in water. The sample is extracted in liquid-liquid mode (dichloromethane) and then the determination of the residues is carried out by capillary gas chromatography with mass spectrometric detection in the Selected-Ion Monitoring mode (SIM). The average recoveries of spiked compounds are in the 78.4–135.4% range between the relative low level (0.100 g L^–1) and the relative high level (10.0 g L^–1). The limits of detection (LOD) are in the 0.009–0.128 g L^–1 range.     

Extractive spectrophotometric determination of dioxouranium(VI) with the sodium salt of hexamethyleneiminecarbodithioate

The optimum conditions for the extractive spectrophotometric determination of dioxouranium(VI) with hexamethyleneiminecarbodithioate(HMICdt) have been established. Dioxouranium(VI) reacts with this ligand at pH 4.5 to form a yellowish-orange uncharged 12 metal-ligand complex which can be extracted by chloroform. The calibration graph was linear in the range of 1–20 g ml^–1 of dioxouranium(VI) at 335 nm. The molar absorptivity of the extracted species is 5.952×10³ l mol^–1 cm^–1 with Sandell's sensitivity of 0.04 g cm^–2. The average of 10 determinations of dioxouranium was 49.75 g for the samples containing 50 g of U(VI) and the variation from the mean at 95% confidence limit was 49.75±0.5955.     

Extraction and Spectrophotometric Determination of Osmium by Tetramethylthiuram Disulphide in Toluene

Summary Tetramethylthiuram disulphide (TMTD) is used for the extraction and spectrophotometric determination ofg quantities of osmium. 15 ml of 1.052×10^–3 M TMTD in toluene quantitatively extracts osmium from7 M HCl. The complex attains maximum colour intensity in 2 hours. It is red in colour and exhibits two max. One at 445 nm and the other at 504 nm. The maximum at 504 nm is more significant. Beer's law was found to hold good over the concentration range of 1.7 to 26.7g of osmium per ml. The Ringbom plot shows the optimum range of 9.42 to 23.65g of osmium per ml. The optimum period of equilibration is 30 seconds and the complex is stable up to 5 hours. The extracted species shows the composition to be 1 1 (Os TMTD). It is possible to extract and determine osmium in the presence of other platinum metals with composition corresponding to the ore osmiridium.

---

Zusammenfassung Tetramethylthiuramdisulfid (TMTD) wurde zur Extraktion und spektrophotometrischen Bestimmung von Mikrogrammengen Osmium verwendet. 15 ml einer 1,052.10^–3-molaren Lösung von TMTD in Toluol dienen zur Extraktion von Os aus 7-m Salzsäure. Der entstandene rote Komplex erreicht innerhalb 2 Stunden maximale Farbintensität und zeigt zwei Absorptionsmaxima bei 445 nm und 504 nm. Letzteres ist signifikanter. Zwischen 1,7 und 26,7g Os/ml gilt das Beersche Gesetz. Nach der Ringbom-Gleichung liegt die geeignetste Konzentration zwischen 9,42 und 23,65g Os/ml. Nach 30 sec stellt sich das Gleichgewicht ein und bleibt bis zu 5 Stunden konstant. Die extrahierte Substanz entspricht der Zusammensetzung 1 1 (Os TMTD). Os läßt sich auch in Gegenwart anderer Platinmetalle so extrahieren und bestimmen.

     

Determination of palladium, platinum and gold by first derivative spectrophotometry

Summary The application of first-derivative spectrometry to the simultaneous determination of palladium(II), platinum(IV) and gold(III) is described. Light absorption of stable chlorocomplexes formed in 1 mol/l hydrochloric acid provides the basis of their determinations. A difference in the derivative amplitudes between two first-derivative zero crossing points of one metal A is read, corrected for the contribution of metal B and used for quantitation of metal C. Palladium (0.48–20 g ml^–1), platinum (0.16–24 g ml^–1) and gold (0.32–24 g ml^–1) have been determined with good precision and accuracy without any separations. Results are also presented for the simultaneous determination of the three precious metals in the presence of several major constituents.     

Spectrophotometric determination of nitrite in environmental waters using column preconcentration on biphenyl

Column preconcentration methods have been established for the spectrophotometric determination of trace nitrite with sulfanilic acid (SA) orp-aminoacetophenone (AAP) as the diazotizable aromatic amine andN, N-dimethylaniline (DMA) or 1-aminonaphthalene (AN) as the coupling agent, using differention-pairs co-precipitated with biphenyl. Nitrite ion reacts with SA in the pH range 2.0–3.0 and AAP in the pH range 1.7–3.0 in HCl medium to form water-soluble colourless diazonium cations. These cations are subsequently coupled with DMA in the pH range 3.7–6.1 for the SA-DMA system and AN in the pH range 1.7–2.3 for the AAP-AN system to be retained on microcrystalline biphenyl packed in a column. The solid mass is dissolved out from the column with 5 ml of DMF and the absorbance is measured by a spectrophotometer at 420 nm for the SA-DMA system and at 517 nm for the AAP-AN system. The calibration was linear over the concentration ranges 0.3–6.0 g of nitrite in 5 ml of DMF solution (i.e., 0.02–0.40 g/ml in the sample solution) for the SA-DMA system and 0.5–7.0 g of nitrite in 5 ml of DMF solution (i.e., 0.03–0.47 g/ml in the sample solution) for the AAP-AN system. The molar absorptivity and Sandell's sensitivity were respectively 2.63 × 10⁴lmol^–1cm^–1 and 1.75 × 10^–3 g cm^–2 for SA-DMA and 3.28 × 10⁴lmol^–1 cm^–1 and 1.40 × 10^–3 g cm^–2 for AAP-AN. The concentration factors were 4 and 16 for SA-DMA and AAP-AN, respectively. The detection limits were 0.0138 and 0.0175 g/ml NO₂ ^– for SA-DMA and AAP-AN, respectively. Seven replicate determinations of a solution containing 3.5 g of nitrite gave mean absorbances of 0.410 and 0.500 with relative standard deviations of 0.51 and 0.55% for SA-DMA and AAP-AN, respectively. Interference from various foreign ions has been studied and the methods have been applied to the determination of nitrite in environmental samples.     

Electrochemical Intercalation of Lithium Ions into Electrolytic Vanadium Pentoxide

The discharge of thin films of Li _x V₂O₅ is described by a mathematical diffusion model. The chemical diffusion coefficient for lithium ions, estimated with the model, is equal to (1.01–2.5) × 10^–11 cm²/s. As the film thickness increases, the discharge capacity at a current of 20 A/cm² tends to the calculated limiting of 3.12 C/cm². The optimum thickness of the film electrode calculated for a discharge current of 20 A/cm² is 33.4 m and agrees satisfactorily with the experimental value.     

2,3-Dihydroxypyridine Loaded Amberlite XAD-2 (AXAD-2-DHP): Preparation, Sorption–Desorption Equilibria with Metal Ions, and Applications in Quantitative Metal Ion Enrichment from Water, Milk and Vitamin Samples

2,3-Dihydroxypyridine loaded (via –N=N–linker) Amberlite XAD-2 (AXAD-2-DHP) was prepared and characterized by elemental analyses, TGA and FT-IR spectra. It (1g packed in a column of 1cm diameter; surface area 135.5m²g^–1) was found to be an effective solid phase sorbent for enriching Zn²⁺, Mn²⁺, Ni²⁺, Pb²⁺, Cd²⁺, Cu²⁺, Fe³⁺ and Co²⁺ at pH 3.5 to 7.0 using flow rates between 1.0–5.0mLmin^–1. For desorption (recovery 97.0–99.8%) of the metal ions, 8 to 10mL of 2.0molL^–1 HCl or 1.5molL^–1 HNO₃ at a flow rate of between 2.0 and 4.0mLmin^–1 were found most suitable. The t_1/2 (time for 50% sorption) is between 2 and 10min when a 50mL solution (containing a total amount of metal of 2mg) was equilibrated with 0.5g of resin. Sorption of all metal ions except Pb²⁺ follows the Langmuir model, whereas for Pb the data fits with the Freundlich model. The sorption capacity is between 60.7 (for Cd) and 406.7 (for Cu) µmolg^–1. The resin can withstand an acid concentration of 6molL^–1 and can be reused for thirty cycles of sorption–desorption. The preconcentration factor varies between 100 and 300. For Cd, Ni and Cu the sorption capacity of 2,3-dihydroxypyridine loaded cellulose is lower than that of the present resin. The tolerance limits of electrolytes, humic acid, complexing agents, Ca²⁺ and Mg²⁺ in the enrichment of all metal ions are reported. The limits of detection are 3.88, 5.37, 8.72, 13.88, 4.71, 1.24, 0.59 and 0.30µgL^–1 for Zn²⁺, Mn²⁺, Ni²⁺, Pb²⁺, Cd²⁺, Cu²⁺, Fe³⁺ and Co²⁺, respectively. The calibration curves for flame AAS determination were linear in the ranges 0.018–1.0, 0.067–5.0, 0.2–5.0, 0.9–20, 0.028–2.0, 0.077–5.0, 0.19–10 and 0.1–3.5µgmL^–1, respectively. All the eight metal ions in river and synthetic water samples, Co in vitamin tablets and Zn in milk samples have been quantitatively enriched with Amberlite XAD-2-DHP and determined by flame atomic absorption spectrometry.     

Determination of Squalene Using High-Performance Liquid Chromatography with Diode Array Detection

A high-performance liquid chromatographic method with photodiode array detection has been developed for the determination of squalene. After treated by extraction and fractional crystallization, squalene was analyzed on a C₁₈ column (150 × 3.9 mm, 5 m) with acetonitrile as mobile phase. Excellent linearity of the calibration curve was observed in the range of 100–40000 gL^–1 and the detection limit was 40 gL^–1. The recoveries were from 89.6% to 100.5% and the relative standard deviations were from 0.5% to 1.4%. The method was successfully applied to the determination of squalene in squalene capsules, olive oil, algal lipids and algal cells.     

Reduction of iodate by hydrazine: Application of the iodide ion selective electrode to the uncatalyzed reaction

Summary The reduction of iodate by hydrazine was examined by use of the iodide ion selective electrode. The rate of reduction of iodate at iodide concentrations below 5 × 10^–5 M is controlled by the direct reduction by hydrazine. At higher iodide concentrations, the rate of reduction of iodate is controlled by the reduction of iodate by iodide with the subsequent reduction of iodine by hydrazine. Application of the reaction to the determination of g quantities of iodine is discussed.

---

Zusammenfassung Die Reduktion von Jodat mit Hydrazin wurde mit Hilfe einer jodid-spezifischen Elektrode untersucht. Das Ausmaß der Jodatreduktion bei Jodid-konzentrationen unter 5·10^–5 Mol/l wurde durch direkte Reduktion mit Hydrazin kontrolliert. Bei höheren Jodidkonzentrationen wurde das Reduk-tionsausmaß des Jodats mit Hilfe der Jodat-Jodid-Reaktion und erst dann durch Reduktion des Jodids mit Hydrazin kontrolliert. Die Anwendung auf die Bestimmung von g-Mengen Jodid wurde diskutiert.

     

Application of l-cysteine-capped nano-ZnS as a fluorescence probe for the determination of proteins

Nanometer-sized l-cysteine-capped ZnS particles have been synthesized and used as a fluorescence probe to investigate the effect of proteins on fluorescent intensity. With =190 nm, maximum and constant synchronous fluorescence enhancement was produced at 267 nm and pH 5.12 in the presence of proteins. A highly sensitive synchronous fluorescence method for the rapid determination of proteins has been developed. Under optimum conditions, calibration graphs are linear over the range 0.03–8.0 g mL^–1 for bovine serum albumin (BSA), 0.01–6.0 g mL^–1 for human serum albumin (HSA), 0.05–8.0 g mL^–1 for -globulin (-G), and 0.04–4.0 g mL^–1 for ovalbumin, respectively. The relative standard deviations of seven replicate measurements were 1.75% for 1.0 g mL^–1 BSA, 1.90% for 1.0 g mL^–1 HSA, 1.65% for 1.0 g mL^–1 -G, and 2.32% for 1.0 g mL^–1 ovalbumin.     

An upper bound to bond electric dipole moments

An upper bound can be set to the dipole moment of the X-H bond (with X+H^– polarity) for symmetrical molecules of XH₄ and XH₃ type from the experimental values of the g factor and bond length. The following upper bounds have been found to the bond dipole moments: CH₄ (C+H^–<0.902 D, SiH₄, (Si+H^–)<4.21 D, GeH₄+ (Ge+H^–)<3.59 D, NH₃ (N+H^–)<0, PH₃ (P+H^–)<2.74 D. These results enable one to rule out certain published data on the dipole moment of the C-H bond in methane as certainly incorrect. In the case of the ammonia molecule, the possibility of N+H^– polarity is ruled out.Translated from Teoreticheskaya i Éksperimental'naya Khitniya, No. 3, pp. 346–350, May–June, 1985.     

Path of “dry” electrons before localization in liquid hydrocarbons

Conclusions On the basis of measurements of values of in liquid hydrocarbons, it has been shown that the path length before localization of a photoliberated electron increases with increasing mobility of the excess electron, from approximately 40 Å (methylcyclohexane) to 200 Å (isooctane). In a liquid with10^–2 cm²/V·sec (methylcyclohexane, hexane), the localization takes place before or immediately after thermalization of the electron. In a liquid with>10^–1 cm²/V·sec, the electron passes through the main part of its path before localization, being in thermal equilibrium with the medium.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 10, pp. 2198–2203, October, 1985.     

Spectrophotometric determination of 6-aminopenicillanic acid using bromophenol blue and bromothymol blue

Two simple, selective and sensitive spectrophotometric methods are described for the determination of 6-aminopenicillanic acid (6-APA). The methods are based on the reaction of 6-APA with either bromophenol blue (BPB) or bromothymol blue (BTB), to give orange-red and green species, respectively. The coloured products are quantified spectrophotometrically at 625 and 616 nm for BPB and BTB, respectively. The optimization of the different experimental conditions is described. No interferences from different -lactams and common degradation products were observed in the determination of 6-APA using BTB, while flucloxacillin, dicloxacillin, adrenaline, vitamin C, urea and common degradation products in any percentage interfere on using BPB only. The BTB method was better than the BPB method, because of its wider range of determination (0.4–20 g ml^–1 vs. 0.4–7.2 g ml^–1 on using BPB), higher molar absorptivity and Sandell sensitivity (3.27 × 10³l mol^–1 cm^–1 and 0.099 g cm^–2 vs. 2.82 × 10³lmol^–1 cm^–1 and 0.115 g cm^–2), greater stability (3 and 10 days on using BTB and BPB, respectively) and better selectivity. The results were compared with those given by the Official United States Pharmacopeial XXI method.     

Accurate determination of lead in wines by inductively coupled plasma mass spectrometry

Summary The capability of inductively coupled plasma mass spectrometry (ICP-MS) for Pb determinations in wine samples is studied. An evaluation is made of the signal behaviour in aqueous ethanolic medium. The effect of preliminary sample preparation on signal suppression or enhancement is investigated in conjunction with the ability of internal standardization to correct for it. As a result, an accurate and precise method of analysis is described in which the sample preparation is limited to a 10-fold dilution and external calibration is applied for quantitation. A detection limit of 0.2 g 1^–1 Pb in wine is achieved. The Pb content of ten different wines was found to range around 40 g 1^–1 with extreme values of 1.63 and 58.8 g 1^–1.     

Extraction-spectrophotometric determination of nickel as Ni-(PAR)2-(CTAB)2 complex in polymetallic sea-bed nodules and steels

A red, water-soluble complex of nickel with PAR can be extracted into chloroform with CTAB at pH 7.0. The system obeys Beer's law upto 0.5 g/ml with a molar absorptivity of 45 200 L·mol^–1·cm^–1 at 540 nm. Job's method of continuous variations revealed that the composition of the extracting species is 1:2:2 for nickel:PAR:CTAB. Based on this extraction, a highly sensitive and selective spectrophotometric method for the determination of nickel in polymetallic sea-bed nodules and in steels, after prior separation of iron and manganese, was developed. The standard deviation was 0.04–0.127 g for 5–25 g of nickel.