纤维素在离子液体[AMMor]Cl/[AMIM]Cl混合溶剂中的溶解性能

研究了纤维素在混配离子液体N-甲基-N-烯丙基吗啉氯盐[AMMor]Cl/3-甲基-1-烯丙基咪唑氯盐[AMIM]Cl中的溶解性能, 结果表明, [AMMor]Cl/[AMIM]Cl混配溶剂能有效溶解天然纤维素, 且在相同条件下, 溶解能力要优于离子液体[AMIM]Cl; 随着溶解温度的升高, 溶解时间大大缩短. 利用FTIR, XRD和TGA方法分析了再生纤维素的化学结构和热稳定性, 结果表明, 未经活化的纤维素可直接溶于[AMMor]Cl/[AMIM]Cl而不发生其它衍生化反应, 且天然纤维素在该溶剂体系中纤维素聚合度下降较小.     

微波法合成离子液体[AMIM]Cl及其对纤维素的预处理

利用微波法合成了离子液体1-烯丙基,3-甲基咪唑氯盐[AMIM]Cl,并利用合成的离子液体分别对微晶纤维素、麦草秸杆和玉米芯进行预处理,得到了再生纤维素。考察了纤维素在离子液体中的溶解过程,并通过FT-IR、SEM和酶解对其预处理效果进行了表征。结果表明:微波法可以大大减少反应时间,合成的离子液体[AMIM]Cl可以有效降低纤维素的结晶度,增加其表面粗糙度,提高纤维素酶的可及性及底物的利用率。     

Thermal stability of ion-exchange Nafion N117CS membranes

The effect of exchanged ions on the thermal stability of Nafion N117CS membranes was investigated by X-ray photoelectron spectra (XPS), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), thermomechanical analysis (TMA), and ion exchange capacity determinations. The ion exchange of alkaline metal ions was effective in improving the thermal stability of the Nafion N117CS membrane. Findings reveal that when Nafion was exchanged for cations with a larger ionic radius, the membrane attained superior thermal stability. On the other hand, we confirmed that the Na-exchange Nafion N117CS membrane possessed a distinctive degree of thermal stability among the alkaline ion-exchange Nafions, although the order of ionic radii is K > Na > Li. Thermal stability improved the most when the Nafion membrane was exchanged for alkaline ions, followed by divalent ions, then trivalent ions. As for the Nafion membrane when it was exchanged for divalent ions or trivalent ions, Nafion following the ion exchange had a thermal stability proportional to an increase in the ionic radius of the cation. This stability may be explained by the reduction of water content and a greater interaction between the sulfonate groups and the cations with larger ionic radii. Since the Al cations acted as a Lewis acid center, the decomposition of the ether bonds of the perfluoroalkylether pendant-chains of the Nafion membrane was observed for the Nafion N117CS membrane that had been exchanged for Al ions. The activation of molecular mobility in Nafion was observed between the decomposition stages of the loss of water and the loss of sulfonic groups. The temperature of activation of cation-exchange Nafion became much higher than that of Nafion in an acid form.     

Thermal stability of surface-esterified cellulose and its composite with polyolefinic matrix

Thermal stability of hydrophobized cellulose powders was investigated from the perspective of potential use as filler in non-polar polyolefinic matrix. The hydrophobization was done by heterogeneous esterification with three carboxylic acids which differ in chain length (3, 10 and 18 carbons). Data measured by means of thermogravimetry (TG) were recalculated according to model-free isoconversional method to construct time–temperature plots. It was demonstrated that the esterification significantly decreases thermal stability of the material, which reduces feasible processing window. Under non-oxidative atmosphere, the single-step decomposition of materials is prevailing, while the process is more complex in air. In both cases the oleic acid esters showed the lowest stability and the original cellulose was the most stable. Finally, all powders were compounded with polyethylene or polypropylene. Obtained composites were then subjected to color measurement and TG. Even though the materials were partly degraded, which was indicated by the yellowish hue of the composites, virtually no impact of the filler pyrolysis on the polymer matrix decomposition was observed, particularly in case of decanoyl esters.     

Characterizations and stability of polyimide-phosphotungstic acid composite electrolyte membranes for fuel cell

Organic-inorganic composite membranes from partially aliphatic sulfonated polyimides and heteropolyacids (HPAs) were synthesized. A series of composite membranes with varying amounts of heteropolyacid were prepared by altering the weight ratio of polyimide and HPA. The partially aliphatic sulfonated polyimides are synthesized from 1,4,5,8-naphthalenetetracarboxylic dianhydride, 4,4′-diaminobiphenyl 2,2′-disulfonic acid as the sulfonated diamine, and decamethylenediamine as the aliphatic diamine. The incorporation of HPA is confirmed by FT-IR analyses. When appropriately embedded in a hydrophilic polymer matrix, the hydrated HPAs are expected to endow the composite membrane with their high proton conductivity, while retaining the desirable mechanical properties of the polymer film. These composite membranes were evaluated for thermal stability, ion exchange capacity, water uptake and proton conductivity. Also the extraction of HPA from the polyimide membranes and their stability in water were determined. Though water uptake and IEC decreased with increase in HPA content, the proton conductivity of the composite membranes increased with increase in HPA weight content. This study shows that partially aliphatic sulfonated polyimide composite membranes with HPA can be a viable substitute for Nafion^® for fuel cells which show good conductivity comparable to Nafion^®117 at temperatures nearing 100 °C, keeping in mind that polyimides have good thermal stability and low cost.     

Thermal and hydrolytic stability of sulfonated polyimide membranes with varying chemical structure

Many important properties required for fuel cell applications including hydrolytic stability, depend on various factors like flexibility of the polymer backbone, ring structure and phase separation. This paper is primarily focused on studying the effect of the chemical backbone structure on the hydrolytic stability and other properties. To study the difference in the hydrolytic stability with change in the chemical backbone structure of sulfonated polyimides we synthesized phthalic sulfonated polyimides and naphthalenic sulfonated polyimides. Two series of phthalic sulfonated polyimides were prepared using 4,4′-oxydiphthalic anhydride (ODPA) and 4,4′-methylene dianiline (MDA), and 4,4′-(hexafluoroisopropylidine) diphthalic anhydride (6FDA) and oxydianiline (ODA). 4,4′-Diaminobiphenyl-2,2′-disulfonic acid (BDSA) was used to introduce sulfonic acid group into both series. Naphthalenic polyimides were synthesized from 1,4,5,8-naphthalenetetra-carboxylic dianhydride, BDSA, MDA and ODA. Also to observe other properties according to variation of sulfonic acid content, the degree of functionalisation was effectively controlled by altering the mole ratio between the sulfonated and non-sulfonated diamine monomers in phthalic sulfonated polyimides. The hydrolytic stability of the polyimides was followed by FT-IR spectroscopy at regular intervals. Polyimides prepared using naphthalenic dianhydride, NTDA, exhibited higher hydrolytic stability than the phthalic dianhydrides. The proton conductivity, ion exchange capacity (IEC) and water uptake measurements revealed the dependence on the molecular weight of the repeating unit. The proton conductivity of the sulfonated polyimides was found to vary with chemical backbone structure.     

Thermal and catalyzed [3,3]-phosphorimidate rearrangements

[3,3]-Sigmatropic rearrangements have been widely utilized for the synthesis of structurally complex organic molecules because of the ease with which carbon-carbon bonds are formed in a regio- and stereocontrolled manner. However, there are far fewer [3,3]-rearrangements available for the selective formation of carbon-nitrogen bonds despite the enormous potential of such reactions for the preparation of stereodefined allylic amines. We describe here the scope and mechanism of a [3,3]-rearrangement of allylic phosphorimidates that provides access to stereodefined allylic amines of diverse structure. The reactive intermediate in the reaction, an allylic phosphorimidate, is produced in situ through the combination of readily available starting materials (allylic alcohols, chlorophosphites, and organic azides), rendering the reaction an efficient three-component process. Analogous to other [3,3]-rearrangements, the stereochemistry in an allylic alcohol starting material is transferred with fidelity to the allylic amine product and, further, allylic amines are produced as single olefin isomers. In addition, a crossover experiment indicates that the rearrangement is an intramolecular process. Finally, activation of the allylic moiety either through incorporation of electron-deficient functional groups or through the use of a transition-metal catalyst significantly facilitates the reaction and consequently the preparation of a wider range of substitution patterns.     

Controlling the lifetime of cucurbit[8]uril based self-abolishing nanozymes

Nature has evolved a unique mechanism of self-regulatory feedback loops that help in maintaining an internal cellular environment conducive to growth, healing and metabolism. In biology, enzymes display feedback controlled switchable behaviour to upregulate/downregulate the generation of metabolites as per the need of the cells. To mimic the self-inhibitory nature of certain biological enzymes under laboratory settings, herein, we present a cucurbit[8]uril based pH responsive supramolecular peptide amphiphile (SPA) that assembles into hydrolase mimetic vesicular nanozymes upon addition of alkaline TRIS buffer (activator) but disintegrates gradually owing to the catalytic generation of acidic byproducts (deactivator). The lifetime of these nanozymes could be manipulated in multiple ways, either by varying the amount of catalytic groups on the surface of the vesicles, by changing the acid generating substrate, or by changing the ratio between the activator and the substrate. The self-inhibitory nanozymes displayed highly tunable lifetimes ranging from minutes to hours, controlled and in situ generation of deactivating agents and efficient reproducibility across multiple pH cycles.

Self-inhibitory feedback regulated transient assembly of a CB[8] based nanozyme is reported whose lifetime can be manipulated in multiple ways, ranging from minutes to hours.     

Thermal resistance and mechanical stability of tungsten oxide filled polymer composite radiation shields

Abstract

The influence of tungsten oxide on thermal and mechanical properties of Isophthalic polyester was studied in detail. Ultrasonication technique was successful in dispersing WO₃ filler particles upto 40?wt% into the polymer matrix and was confirmed through the Scanning Electron Microscopy technique. The mechanical strength of the composites was found to increase with increase in the WO3 content and is acting as a reinforcer. About 77.4%, 65.4% and 7–8 times increase was observed in tensile, flexural and compressive strength respectively with respect to pristine. The thermogram of the composites reveal two stages of degradation. Maximum weight loss was observed in the first stage of degradation in almost all the composites. The initial degradation temperature of the composites range from 151?°C–226?°C. Activation energy was estimated using Horowitz–Metzger kinetic theory and was found to range from 25.31 to 78.58?kJ/Mol. The 50?wt% WO3 filled composite exhibits excellent thermal stability and mechanical strength. Thus, WO₃ filler particles were successful in enhancing the thermal and mechanical strength of Isophthalic polyester.     

Thermal stability and lifetime estimates of a high temperature epoxy by Tg reduction

Thermal degradation of a high temperature epoxy network is studied in terms glass transition temperature (T_g) reduction over a temperature window encompassing the T_g of the network. The T_g is shown to decrease as the network is thermally aged at elevated temperatures in air and in argon. The duration of the aging experiments is extended to long time such that the absolute T_g reduction approaches a long time reduction plateau. Degradation is dominated by non-oxidative pyrolysis with a small contribution from diffusion limited thermal oxidative degradation at the surface. A time–temperature superposition is constructed from the extent of T_g reduction of samples aged in air and the thermal shift factors are shown to have Arrhenius scaling behavior. An activation energy is extracted that agrees with previous activation energy measurements derived from other property measurements of the same network aged under similar conditions. The agreement of the activation energy with past results shows that T_g reduction is controlled by the same degradation mechanism and may be used as an observable for lifetime estimates when thermal degradation is pyrolytic in nature. The extent of T_g reduction is modeled with an autocatalytic rate expression and compared to previous property measurements to show the difference in sensitivity of observable material properties on degradation.     

Location of [60]fullerene incorporation in lipid membranes

We confirmed that most C(60) fullerene units are located in the hydrophobic core of the lipid bilayer membrane in water-soluble lipid membrane incorporated C(60) (LMIC(60)) complexes using differential scanning calorimetry (DSC) and (13)C NMR spectra in the presence of radical labels.     

Microwave-Assisted and Thermal Synthesis of Calix[4]arene Derivatives

Russian Journal of Organic Chemistry - Some tert-butylcalix[4]arene derivatives were synthesized by thermal and microwave methods. The microwave method was conducted in two ways: (1) all the...     

Thermogravimetric analysis of SPEEK membranes: Thermal stability, degree of sulfonation and cross-linking reaction

Thermal degradation of SPEEK membranes is studied by coupling thermogravimetric analysis (TGA) and mass spectrometry (MS). Main mass losses can be attributed to water evaporation, desulfonation and oxidative pyrolysis of polymer main chain. The analysis can be used to determine the degree of sulfonation (DS) and the degree of cross-linking (DCL) between macromolecular chains. Furthermore, the thermogravimetric curves can be modelled using non-isothermal chemical kinetics, allowing determination of activation energies during thermal degradation of SPEEK membranes.     

Thermal unimolecular isomerization of 1,4-dimethylbicyclo[2.2.0]hexane, 1,4-dimethylbicyclo[2.1.1]hexane,and 1,4-dimethylbicyclo[2.1.0]pentane

The thermal isomerization of the title compounds was studied in the vapor phase. Over the temperature range from 445.1 to 477.5°K, 1,4-dimethylbicyclo[2.2.0]hexane underwent a homogeneous unimolecular reaction to 2,5-dimethyl-1,5-hexadiene, the rate constants being represented by the equation: k = 1.86 × 10¹¹ exp (?31000 ± 1800/RT) sec^?1. Over the temperature range from 630.0 to 662.2°K, 1,4-dimethylbicyclo[2.1.1]-hexane also underwent a unimolecular isomerization to the same product, the rate constants being given by the equation: k = 8.91 × 10¹⁴ exp (?56000 ± 900/RT) sec^?1. The pyrolysis of 1,4-dimethylbicyclo[2.1.0]pentane gave 1,3-dimethylcyclopentene-1 and 2,4-dimethyl-1,4-pentadiene in the ratio of 9:1. The former reaction was influenced by surface effects but the latter was not. The rate constants for the formation of 2,4-dimethyl-1,4-pentadiene fitted the equation: k = 1.66 × 10¹⁷ exp (?57400 ± 3100/RT) sec^?1. The effect of the two methyl groups at the bridgehead positions in these molecules in influencing the rate of decomposition is discussed in terms of the non-bonded repulsive forces between the substituents.     

Effect of SiO2 on relaxation phenomena and mechanism of ion conductivity of [Nafion/(SiO2)x] composite membranes

This report describes a study of the effect of SiO2 nanopowders on the mechanism of ionic motion and interactions taking place in hybrid inorganic-organic membranes based on Nafion. Five nanocomposite membranes of the formula [Nafion/(SiO2)x] with SiO2 ranging from 0 to 15 wt % were prepared by a solvent casting procedure. TG measurements demonstrated that the membranes are thermally stable up to 170 degrees C but with the loss water it changes the cluster environments and changes the conductivity properties. MDSC investigations in the 90-300 degrees C temperature range revealed the presence of three intense overlapping endothermal peaks indicated as I, II, and III. Peak I measures the order-disorder molecular rearrangement in hydrophilic polar clusters, II corresponds to the endothermic decomposition of -SO3 groups, and III describes the melting process in microcrystalline regions of hydrophobic fluorocarbon domains of the Nafion moiety. ESEM with EDAX measurements revealed that the membranes are homogeneous materials with smooth surfaces. DMA studies allowed us to measure two relaxation modes. The mechanical relaxation detected at ca. 100 degrees C is attributed to the motion of cluster aggregates of side chains and is diagnostic for R-SO3H...SiO2 nanocluster interactions. DMA disclosed that at SiO2/-SO3H (psi) molar ratios lower than 1.9, the oxoclusters act to restrict chain mobility of hydrophobic domains of Nafion and the dynamics inside polar cages of [Nafion/(SiO2)x] systems; at psi higher than 1.9, the oxoclusters reduce the cohesiveness of hydrophilic polar domains owing to a reduction in the density of cross-links. FT-IR and FT-Raman studies of the [Nafion/(SiO2)x] membranes indicated that the fluorocarbon chains of Nafion hydrophobic domains assume the typical helical conformation structure with a D(14pi/15) symmetry. These analyses revealed four different species of water domains embedded inside polar cages and their interconnecting channels: (a) bulk water [(H2O)n]; (b) water solvating the oxonium ions directly interacting with sulfonic acid groups [H3O+...SO3(-)-].(H2O)n; (c) water aggregates associated with H3O+ ions [H3O+.(H2O)n]; and (d) low associated water species in dimer form [(H2O)2]. The conductivity mechanism and relaxation events were investigated by broadband dielectric spectroscopy (BDS). [Nafion/(SiO2)x] nanocomposite membranes were found to possess two different molecular relaxation phenomena which are associated with the alpha-relaxation mode of PTFE-like fluorocarbon domains and the beta-relaxation mode of acid side groups of the Nafion component. Owing to their strong coupling, both these relaxation modes are diagnostic for the interactions between the polar groups of the Nafion host polymer and the (SiO2)x oxoclusters and play a determining role in the conductivity mechanism of the membranes. The studies support the proposal that long-range proton charge transfer in [Nafion/(SiO2)x] composites takes place due to a mechanism involving exchange of the proton between the four water domains. This latter proton transfer occurs owing to a subsequent combination of domain intersections resulting from the water domain fluctuations induced by the molecular relaxation events of host Nafion polymer.     

Theoretical study of the [10]-annulenes geometry and stability

Five structures of [10]-annulene, proposed in the literature, namely the naphthalenic, planar, boat and helix forms have been studied by EHT, CNDO/2, MINDO/2 methods and the empirical method of Dashevskyi. Optimum geometries of the single structures were determined either from energy curves or from the coplanarity condition for bond groups of the ethylenic type. The relative stabilities of the structures were established by comparing their heats of formation with the values of the other stable cyclic polyenes. The most favourable boat form appears as an antiaromatic inverse to benzene.     

Thermal rearrangements of spiro[2.4]hepta-1,4,6-trienes

Thermolysis of spiro[2.4]hepta-1,4,6-triene (1a) at 50 degrees C yielded bicyclo[3.2.0]hepta-1,3,6-triene (5), which dimerized in two different fashions to form cyclobutanes. The 1,2-dimethyl and 1-propyl derivatives of 1a also rearranged at 50 degrees C, but at a faster rate, each yielding a pair of cyclobutane dimers. The structures of these symmetrical dimers were investigated by 1D and 2D NMR and NOE difference spectroscopy. Ab initio calculations indicated that the two strained olefins 1a and 5 had comparable energies about 50 kcal/mol lower than norborna-1(7),2,5-triene, which was thus excluded as a reaction intermediate.