Voltammetric Behavior of Dopamine at ct-DNA Modified Carbon Fiber Microelectrode

A sub-micrometer thin-layer DNA modified carbon fiber microcylinder electrode was prepared by electrodeposition of ct-DNA at 1.5V (vs. Ag/AgCl). The voltammetric behavior of dopamine (3-hydroxytyramine) was investigated at the modified electrode. It was found that the modified electrode exhibits a highly electrocatalytic activity toward dopamine oxidation. Differential pulse voltammetry was used for determination of dopamine in pH 7.4 phosphate buffer solution. A linear response of the peak current versus the concentration was found in the range of 4×10^–6 to 10^–4molL^–1 at 10^–4molL^–1 AA (ascorbic acid) coexistence (R=0.9959) and the range of 6×10^–5 to 10^–3molL^–1 at 10^–3molL^–1 AA (R=0.9960). The presence of a high concentration of ascorbic acid did not interfere with the determination. The proposed method exhibited good recovery and reproducibility. This method can be applied to the detection of DA in real samples.     

Electrochemical Determination of 4-Nitrophenol Using a Single-Wall Carbon Nanotube Film-Coated Glassy Carbon Electrode

A single-wall carbon nanotubes (SWNT) film coated glassy carbon electrode (GCE) was fabricated for the direct determination of 4-nitrophenol (4-NP). The electrochemical behaviors of 4-NP at the SWNT-film coated GCE were examined. In 0.1M phosphate buffer with a pH of 5.0, 4-NP yields a very sensitive and well-defined reduction peak at the SWNT-modified GCE. It is found that the SWNT film exhibits obvious electrocatalytic activity towards the reduction of 4-NP since it not only increases the reduction peak current but also lowers the reduction overpotential. Based on this, an electrochemical method was proposed for the direct determination of 4-NP. The reduction peak current varies linearly with the concentration of 4-NP ranging from 1×10^–8 to 5×10^–6M, and the detection limit is 2.5×10^–9M after 3min of open-circuit accumulation. The relative standard deviation at 2×10^–7M 4-NP was about 6% (n=10), suggesting excellent reproducibility. This new method was successfully employed to determine 4-NP in several lake water samples.     

Determination of Caffeine Using a Simple Graphite Pencil Electrode with Square-Wave Anodic Stripping Voltammetry

A simple commercial graphite pencil electrode (GPE) was utilized for monitoring caffeine using the square-wave anodic stripping voltammetry (SWASV) method. This method was applied to determine the caffeine levels in several tea samples, which yielded a relative error of 1% in the concentrations. Caffeine was deposited at 0.0V (vs. Ag/AgCl), then reduced at +1.40V to strip it on the GPE. Optimal experimental conditions for the analysis were found to be as follows: pH value of 9 for the medium; deposition potential of 0.0V; deposition time of 120s; SW frequency of 25Hz; SW amplitude of 45mV, and step potential of 6mV. Given these optimum conditions, a linear range was observed within the concentration of 0500mgL^–1. At caffeine concentrations of 50.0, 250.0, and 500.0mgL^–1, the relative standard deviations in measured concentrations (n=12) were 0.19, 0.09, and 0.11%, respectively. The detection limit was found to be 9.2mgL^–1, which is comparable with the result obtained using a carbon paste electrode, equivalent to 8.2mgL^–1.     

Determination of Total Selenium Content in Cereals and Bakery Products by Flow Injection Hydride Generation Graphite Furnace Atomic Absorption Spectrometry Applying in-situ Trapping on Iridium-Treated Graphite Platforms

A flow injection hydride generation graphite furnace atomic absorption spectrometric (FI-HG-GFAAS) method was applied to the determination of Se in Se-doped and undoped cereals and bakery products. For the purpose of doping, the soils used for the cultivation of the cereals were dosed with Se-doped foliar fertilizers. The samples were dissolved in a mixture of HNO₃ and H₂O₂ solutions using microwave-assisted digestion. The decomposition of H₂Se generated from the sample solutions and the trapping of elemental Se were performed at a temperature of 300°C on an Ir-pretreated integrated graphite platform of a transversally heated graphite atomizer (THGA). For release of the trapped Se within a fairly short atomization time (5s), an atomization temperature of 2200°C was observed to be optimal. The overall efficiency of hydride generation, transport and trapping was 86%.The upper limit of the linear dynamic range of calibration was 10µgL^–1, which corresponds to 0.5µgg^–1 for solid samples. Recovery of the samples spiked with Se^VI solutions was found to be 93±6% on average. The relative standard deviation of the determinations was less than 8%. The limit of detection was found to be 0.06µgL^–1, corresponding to 3ngg^–1 for solid samples. The accuracy of the method was verified with the use of IAEA-155 (whey powder) certified reference material. End-capped THGA tubes resulted in an extension of the linear calibration range compared to that of standard THGAs.The Se content in bakery products made of undoped cereals ranged from 7.7 to 68ngg^–1 (wet weight) in 18 samples, whereas the Se content of the corresponding cereals was found to be below 100ngg^–1 (wet weight). The Se level of cereals grown on soils treated with Se-doped fertilizers ranged from 128 to 1046ngg^–1 (wet weight), and it depended linearly on the Se concentration of the corresponding foliar fertilizer.     

Determination of Heavy Metal Ions in Chinese Herbal Medicine by Microwave Digestion and RP-HPLC with UV-Vis Detection

A new method for the simultaneous determination of heavy metal ions in Chinese herbal medicine by microwave digestion and reversed-phase high-performance liquid chromatography (RP-HPLC) has been developed. The Chinese herbal medicine samples were digested by microwave digestion. Lead, cadmium, mercury, nickel, copper, zinc, and tin ions in the digested samples were pre-column derivatized with tetra-(4-chlorophenyl)-porphyrin (T₄-CPP) to form the colored chelates which were then enriched by solid phase extraction with C₁₈ cartridge and eluted from the cartridge with tetrahydrofuran (THF). The chelates were separated on a Waters Xterra RP₁₈ column by gradient elution with methanol (containing 0.05molL^–1 pyrrolidine-acetic acid buffer salt, pH=10.0) and THF (containing 0.05molL^–1 pyrrolidine-acetic acid buffer salt, pH=10.0) as mobile phase at a flow rate of 0.5mLmin^–1 and detected with a photodiode array detector in the range of 350–600nm. In the original samples the detection limits of lead, cadmium, mercury, nickel, copper, zinc and tin are 4ngL^–1, 3ngL^–1, 6ngL^–1, 5ngL^–1, 2ngL^–1, 6ngL^–1, and 4ngL^–1, respectively. This method was applied to the determination of lead, cadmium, mercury, nickel, copper, zinc and tin in Chinese herbal medicine samples with good results.     

Solid-Phase Extraction with Slurry Injection of the Resin Into ETAAS for Trace Determination of Thallium in Natural Water

Thallium in natural water samples was determined by electrothermal atomic absorption spectrometry after 1000-fold enrichment by mini solid-phase extraction from a 100-mL sample solution. A Tl-pyrrolidine-1-carbodithioate complex formed in a sample solution of pH 1.6 was extracted on fine particles of a cellulose nitrate resin dispersed in the sample solution. The cellulose nitrate resin was then collected on a membrane filter (25mm^ø) by filtration under suction using a glass funnel with an effective filtration area of 0.64cm². As a result, a circular thin layer of the resin phase with a diameter of 9mm was obtained. Then the resin phase was carved out by an acrylate resin puncher with a 10-mm^ø hole to put it into a sample cup containing 100µL of 10mM HNO₃ containing 0.5mM NaCl. The resin phase was suspended in the solution by ultrasonication. 1000-fold enrichment was thus attained within 15min, and the suspension was delivered to electrothermal atomic absorption spectrometry. The linear calibration graph was obtained in the range of 0–4ng of Tl in 100mL of a sample solution. The detection limit obtained by 3 method was 0.19ng. The proposed method was applied to the determination of Tl in natural water samples. The results showed the concentration of Tl in seawater was 12.1±1.8pgmL^–1 for the calibration graph method and 12.6±1.4pgmL^–1 for the standard addition method. A snowmelt sample contained 20.7±1.0pgmL^–1 of Tl.     

Determination of Attogram Quantities of Silver via Quenching of the Solid Substrate Room-Temperature Phosphorescence of Rhodamine B Based on the Catalysis of its Oxidation by Potassium Persulfate

A new method of SS-RTP for the determination of trace silver has been established. This method is based on the fact that Ag⁺, when activated by ,-bipyridyl (bipy) in a media of HAc–NaAc (pH=4.9), can catalyze the reaction of Rhodamine B (RhoB) oxidized by K₂S₂O₈, thus causing the Solid Substrate Room-Temperature Phosphorescence (SS-RTP) of RhoB to be quenched. The activating efficiency of bipy is 6.7 times higher than that of o-phenanthroline (phen). The reduction of the phosphorescence intensity (I_p) of RhoB is directly proportional to the concentration of Ag⁺ ions in the range of 1.6016.0agspot^–1 (0.40µLspot^–1). The regression equation of the working curve can be expressed as I_p=18.78+5.100m_Ag+ (agspot^–1) (r=0.9994, n=6), the detection limit is 0.28agspot^–1. This rapid, accurate and sensitive method has been successfully applied to the determination of trace silver in tea and human hair samples, and the results agree well with the Atomic Absorption Spectroscopy (AAS) method. The mechanism of the catalyzing reaction is also discussed.     

Determination of Iron in Tap and Waste Water Using Liquid–Liquid Extraction in a Flow-Injection System

A flow-injection procedure for the determination of iron(III) in water is described. The procedure is based on the formation of an ion pair between the tetraphenylarsonium (Ph₄As⁺) (TPA) or tetrabutylammonium (But₄N⁺) (TBA) cations and the tetrathiocyanatoferrate(III) complex (TTF). This ion pair is extracted with chloroform, and the absorbance of the organic phase is measured at 503nm (for Ph₄As⁺) or 475nm (for But₄N⁺). Iron concentrations higher than 0.9×10^–6molL^–1 (50µgL^–1) can be detected in the first case, with a relative standard deviation of 1.9% (n=12), a linear application rangeof between 1.34 and 54.0×10^–6molL^–1 (75–3015µgL^–1), and a sampling frequency of 30h^–1. For the ion pair with But₄N⁺, the detection limit is 0.52×10^–6molL^–1 (29µgL^–1), with a relative standard deviation of 1.6% and a linear application range between 0.73 and 54.0×10^–6molL^–1. Under the proposed working conditions, only Pd(IV), Cu(II) and Bi(III) interfere. With the application of the merging zones technique, considerable amounts of organic reagent can be saved. The TBA method was applied to the analysis of iron(III) in tap and industrial waste waters.     

Use of a Packed Minicolumn Connected to a Syringe for Determination of Trace Elements in Biological and Water Samples by Flame Atomic Absorption Spectrometry

In this study, a syringe-connected minicolumn resin was used for the separation and enrichment of cadmium, copper, nickel and zinc prior to their determination by flame atomic absorption spectrometry. The proposed technique was compared with classical batch and column techniques in terms of rapidness, simplicity, enrichment and risk of contamination. The minicolumn was filled with Chromosorb-103 resin and connected to a syringe. If the samples were treated with ammonium pyrrolidine dithiocarbamate or 8-hydroxyquinoline, the analytes were quantitatively retained at pH2 and pH5 on the resin, respectively. On the other hand, if no chelating agent was added, the analytes were quantitatively retained at pH10. The analytes retained by the resin were quantitatively eluted by drawing and discharging nitric acid in acetone. The analytes in spiked river-water samples and in certified standard reference Bovine-Liver (NIST SRM 1577 b) were quantitatively (94%) recovered. The relative standard deviations for the determinations were found to be 1.0–10%.     

Selective Spectrophotometric Determination of Aluminium in the Presence of Beryllium and Lanthanide Cations

A spectrophotometric method for the selective determination of Al(III) in the presence of Be and Ln (lanthanide) cations is proposed. It is based on the selective reaction of SXO (Semi-Xylenol Orange) with Al(III) at pH 2.6. The presence of 8%v/v of 1,2-ethanediol serves to stabilize the chelate formed by heating at 100°C for 5min. 0.5mg each of Be(II), Ce(III), La(III), 4mg of Mn(II), 1.2mg of Pb(II), 1mg of Tl(I), 40mg each of Ca(II) and Mg(II) and 1.9mg of sodium dihydrogen phosphate are tolerable. A ligand buffer of HEDTA-Pb is incorporated to further enhance the selectivity of the color reaction. Under the specified conditions SXO reacts with Al(III) to form a 1:1 chelate. Its molar absorptivity at 526nm was found to be 3.3×10⁴Lmol^–1cm^–1. The linear regression equation for 2–20µg of Al(III) is A=0.04458C+0.0112 (where C stands for the concentration of Al(III), µg per 25mL) and correlation coefficient =0.9988. The RSD at the level of 10µg (n=10) and LOQ were found to be 3.5% and 2µg, respectively.     

Flame Atomic Absorption Spectrometric Determination of Gold and Palladium Using Microcolumn On-line Preconcentration and Separation

A microcolumn on-line preconcentration and separation system was developed for the flame atomic absorption spectrometric (FAAS) determination of trace levels of gold and palladium. The analytes were selectively adsorbed onto the microcolumn packed with 2-mercaptothiazole immobilized silica gel (MBTSG) in an acidity range of 0.1 to 6.0M HCl at a sampling flow rate of 4.0mLmin^–1. The analytes adsorbed could be desorbed by a thiourea solution with a flow rate of 2.0mLmin^–1. Most of the common coexisting metal ions at a concentration of 25.0mgmL^–1 and anions at a concentration of 50.0mgmL^–1 did not interfere with the preconcentration and determination of Au and Pd. The limits of detection (LOD), defined as three times the standard deviation of the blank (3), of Au and Pd are 10ngmL^–1 and 26ngmL^–1, respectively, with a preconcentration time of 60s. The relative standard deviation (RSD) is about 2.0% for 0.20µgmL^–1 Au and 0.30µgmL^–1 Pd. With a sample loading time of 30min, 6.7ngmL^–1 Au and 10ngmL^–1 Pd can be preconcentrated quantitatively. A geological sample, an anode slime and a secondary nickel alloy were successfully determined with the proposed method, and the results obtained showed good agreement with the certified values.Received December 23, 2002; accepted May 14, 2003 Published online August 8, 2003     

Determination of Lead Using a New Chromogenic Reagent 2-(2-Sulfo-4-acetylphenylazo)-7-(2,4,6-trichlorophenylazo)-1,8-dihydroxynaphthalene-3,6-disulfonic Acid

A novel chromogenic reagent, 2-(2-sulfo-4-acetylphenylazo)-7-(2,4,6-trichlorophenylazo)-1,8-dihydroxynaphthalene-3,6-disulfonic acid 1, was prepared by diazo coupling of 4-acetylaniline-2-sulfonic acid and 2,4,6-trichloroaniline to chromotropic acid through –N=N– groups. Based on this reagent, a simple, sensitive and selective spectrophotometric method was developed for the determination of lead. In 0.20M phosphoric acid medium, lead reacts with 1 to form a 1:2 blue complex with an absorption maximum of 654nm. Beers law is obeyed in the range of 0–0.6mgL^–1 of lead. The apparent molar absorptivity is 1.25×10⁵Lmol^–1cm^–1. The detection limit and quantification limit were found to be 0.63µgL^–1 and 2.1µgL^–1, respectively. The relative standard deviation for eleven replicate measurements was of 2.6%. The interference of foreign ions was also investigated. All the other foreign ions studied did not interfere with lead determination except for Ca(II) and Ba(II). The interference caused by Ca(II) and Ba(II) can be eliminated by prior extraction of lead with potassium iodide-methylisobutylketone (KI-MIBK). The proposed method was applied to the determination of lead in certified samples with satisfactory results.     

Magnetic Separation Immunoassay for Digoxin in Plasma with Flow Injection Fluorescence Detection

Immunoassay (IA) is a sensitive and selective approach for low level quantitation of drugs. Magnetic separation immunoassays use magnetic beads to facilitate the separation of bound labeled antigens from free antigens in solution. Digoxin was chosen for this study because low level analysis (ngmL^–1) in biological samples isrequired, antibodies to digoxin were commercially available and derivatization procedures for fluorescence labeling were well established. A competitive immunoassay format was used in this study. Streptavidin coated magnetic beads were attached to biotinylated anti-digoxin antibodies for the separation. The inhibition curve for off-line magnetic separation immunoassay of digoxin in spiked plasma was characterized and the dynamic range of the curve was 0.25–2.5ngmL^–1. A power fit weighted by the inverse of concentration was found to provide the best fit to the data (r=0.9934). The percent RSDs for the two controls, 0.8 and 2.2ngmL^–1, were 9.95% and 20.62% (n=6) and the percent errors were 11.75% and 22.63% (n=6), respectively. The limit of detection (LOD) in plasma is 0.14ngmL^–1. The dynamic range of the inhibition curve for on-line magnetic separation immunoassay of digoxin was 0.5–15ngmL^–1 of digoxin. A quadratic fit was found to provide the best fit to the data (r=0.9937). The percent RSDs for the two controls, 4.0 and 12ngmL^–1, were 14.1% and 10.7% (n=6) and the percent errors were 5.8% and 3.3% (n=6) from the spiked value, respectively. The LOD was estimated to be 0.44ngmL^–1 (determined as two times the standard deviation of the blank, n=6). The on-line method has the advantages of being relatively easy to automate in the continuous flow mode and is adaptable for use in conjunction with HPLC separations.     

Determination of Trace Proteins by Rayleigh Light Scattering Technique with Indophenol Blue

The interaction of indophenol blue (IPB) with proteins in aqueous solution has been studied by optical absorption and Rayleigh light scattering (RLS) spectroscopy. At pH 3.8, the weak RLS of IPB is enhanced by proteins. Based on this phenomenon, a novel method for the determination of proteins at nanogram levels using the RLS technique is developed. The method is simple, practical and sensitive. The linear range is 0.25–20.9µgmL^–1 for BSA, and 0.25–17.6µgmL^–1 for HSA. The detection limits (S/N=3) are 23ngmL^–1 for BSA and 22ngmL^–1 for HAS. The results for the determination of proteins in human serum samples are very close to those obtained by an established clinical method. There is very little interference from amino acids, metal ions or other coexisting compounds.     

Determination of Arsenic in Food Samples by Hydride Generation – Atomic Absorption Spectrometry

A method for the determination of trace amounts of arsenic in food samples using flow injection analysis and atomic absorption spectrometry with hydride generation (FI-HG AAS) was developed. The parameters of the flow injection system and the hydride generation were optimized with respect to reagent concentrations, atomization temperature, injection volume, reaction coil length and carrier flow rate. The limits of detection and quantification were 0.34µgL^–1 and 1.2µgL^–:1, respectively, and the analytical curve is linear up to 30.0µgL^–1 arsenic. The relative standard deviation for 12 replicates varies between 5% for 4.0µgL^–1 As and 1.8% for 30.0µgL^–1 As, with an injection frequency of up to 135h^–1. Interferences from Ni(II), Cu(II), Fe(III), Cr(III), Mo(II), Bi(III), Se(IV), Se(VI), Sb(III) and Sb(V) could be masked with a mixture of ascorbic acid-KI in a 5.0molL^–1 HCl solution. The accuracy of the proposed method was evaluated by using certified reference materials of biological samples, and the method was used to determine the content of arsenic in fish and coffee beans.     

Flow Injection Determination of Lomefloxacin Based on Photochemically Sensitized Chemiluminescence

A photochemical chemiluminescence (CL) method for the determination of lomefloxacin (LFX) is proposed. LFX undergoes a photochemical reaction when irradiated with ultraviolet light, and a complex is formed when the photoproduct reacts with terbium(III), which can greatly enhance the CL of the Ce⁴⁺–Na₂SO₃ system. Under optimum experimental conditions, the linear range is between 9.0×10^–10 and 1.0×10^–5M, and the detection limit is 2.2×10^–10M. The relative standard deviation for the determination of 5.0×10^–8M LFX was 3.0% (n=11). The method has been successfully applied to the determination of LFX in dosage form, serum samples and urine samples. The recoveries were 97.9–102.3% for serum and urine samples. The possible mechanism is presented.     

Determination of Iron(III), Cobalt(II) and Chromium(III) in Various Water Samples by Flame Atomic Absorption Spectrometry After Preconcentration by Means of Saccharomyces Carlsbergensis Immobilized on Amberlite XAD-4

A method for the determination of Fe(III), Co(II) and Cr(III) by flame atomic absorption spectrophotometry (FAAS) after preconcentrating on a column containing S. carlsbergensis immobilized on Amberlite XAD-4 has been developed. The optimum values of pH, amount of adsorbent, elution solution and flow rate of the sample solution were determined for the quantitative recovery of the analytes. The effect of interfering ions on the recovery of the analytes was also investigated. Under the optimum conditions, recoveries of Fe(III), Co(II) and Cr(III) by S. carlsbergensis immobilized on Amberlite XAD-4 were 99±2, 100±2 and 98±2% at 95% confidence level, respectively. The limit of detections for Fe(III), Co(II) and Cr(III) were 2.8, 3.9 and 7.4ngmL^–1, respectively. The proposed method was applied to the determination of the analytes in various water samples. The validity of the method was checked with spiked water samples. Fe(III), Co(II) and Cr(III) was determined with a relative error of less than 5%.     

Determination of Iodine in Enriched Chlorella by ICP-OES in the VUV Region

A method of determining iodine in the vacuum ultraviolet region by inductively coupled plasma optical emission spectrometry in enriched Chlorella is established and evaluated. Alga Chlorella samples enriched with iodine were solubilized with tetramethylammonium hydroxide. The iodine content was quantified by inductively coupled plasma optical emission spectrometry using the 182.980nm emission line of iodine to avoid the spectral interference from phosphorus which occurs in Chlorella at the 178.218nm emission line of iodine. The methods accuracy was confirmed by a modified Sandell and Kolthoff spectrophotometric method (As³⁺, Ce⁴⁺ and brucine) after alkaline ashing, and the agreement between the methods was about 96%. The limit of detection in real samples was 3mgkg^–1 for enriched Chlorella, and the iodine content in the samples varied between 100 and 1300mgkg^–1.     

A Simple Sensitive Spectrophotometric Method for the Determination of Ce4+ Using Variamine Blue as a Chromogenic Reagent

A rapid and sensitive spectrophotometric method is described for the determination of trace amounts of cerium using Variamine Blue (VB) as a chromogenic reagent. The proposed method is based on the reaction of cerium with potassium iodide in acidic medium to liberate iodine, which oxidizes Variamine Blue to give a violet colored species with an absorption maximum at 560nm. Beers law was obeyed in the range 2–10µg mL^–1 of cerium. The molar absorptivity and Sandells sensitivity are found to be 1.65×10⁴L mol^–1cm^–1 and 8.48×10^–3µgcm^–2, respectively. The proposed method has been successfully applied to the determination of cerium in alloy and synthetic mixtures.     

Detection of Hydrogen Peroxide in River Water via a Microplate Luminescence Assay with Time-Resolved (“Gated”) Detection

Hydrogen peroxide (HP) in river water was determined using the highly luminescent Eu³⁺-tetracycline hydrogen peroxide (EuTc-HP) complex. A 15-fold increase in luminescence intensity of Eu³⁺-tetracycline (EuTc) is observed at 616nm after formation of EuTc-HP. In order to eliminate interferences by other fluorescent substances that exist in river water, a time-resolved scheme is employed: EuTc-HP has a main decay time of 61µs, while background fluorescence decays within a few ns. Thus, by performing measurements after a delay time of typically 30µs, the signal becomes highly specific for EuTc-HP. Under optimized conditions (pH 7 in MOPS buffer), the calibration curve for the determination of HP was linear over the range of 2 to 160µmolL^–1. The limit of detection is 1.1µmolL^–1 HP. An average recovery of 99.5% was obtained for measurements of river water samples spiked with HP. The relative standard deviation of less than 2% indicates the high accuracy and precision of the method.