Volume Fraction Effects in Electroacoustic Measurements

We measured the dynamic mobility of a polystyrene latex at 1 MHz as a function of volume fraction using the ESA-8000. The volume fraction dependence is compared with a semiempirical equation as well as with some theoretical predictions. It turns out that our polystyrene latex exhibits a volume fraction dependence much weaker than that predicted by any of the theories. This suggests that (polystyrene) latices may not be the ideal model system and that the centrifugation process may influence the surface structure of the particles. We also measured the dynamic mobility spectrum of a silica sol as a function of volume fraction using the Acoustosizer. The experimental spectrum of the silica sol was found to agree reasonably well with the semiempirical and theoretical spectra, especially below φ=0.144. At higher volume fractions we observed positive phase angles that were not predicted by the semiempirical method nor the cell model.     

Effects of dispersion concentration on the electroacoustic potentials of o/w miniemulsions

Electroacoustic potentials are measured for toluene in water miniemulsions stabilized by cetyl alcohol (CA) and 10 mM sodium lauryl sulfate (SLS). The general trend with increasing CA concentration is a sharp drop in the potential up to 20 mM CA, after which the potential remains relatively constant as the CA concentration is further increased. The general trends in the electrokinetic sonic amplitude (ESA) and ζ-potential calculated ESA agree with the ζ-potential determined with microelectrophoresis for o/w miniemulsions prepared at several CA concentrations. However, the magnitude of the electroacoustic ζ-potential is two to three times lower than that of the electrophoretic ζ-potential. Dilution experiments show that the dynamic mobility varies linearly with the dispersion concentration, indicating that particle-particle interactions cancel in the electroacoustic field. The magnitude of the ζ-potential calculated from the dynamic mobility extrapolated to infinite dilution remains lower than that of the electrophoretic ζ-potential. Similar behavior is observed for a monodisperse polystyrene latex.     

Electrooptics of β-FeOOH Particles in Aqueous Media: 1. Reversing-Pulse Electric Birefringence in the Low Field Region

Reversing-pulse electric birefringence (RPEB) of a nearly monodisperse iron(III) hydroxide oxide sample in the β-form (β-FeOOH) was measured at 25°C and at a wavelength of 633 nm in aqueous media in the presence of NaCl. The concentrations of β-FeOOH and added NaCl varied between 0.00111 and 0.0555 g/L and 0.03 and 2.0 mM, respectively. Except for the suspensions with high salt concentrations, each RPEB signal showed a dip or minimum in the reverse process upon electric field reversal, together with a smooth rise in the buildup and a fall in the decay process. The observed signals were analyzed with a new RPEB theory, which takes into account not only the permanent electric dipole moment (μ) but also the root-mean-square ionic dipole moment (m^21/2) due to the ion fluctuation in ion atmosphere, in addition to the field-induced electronic (covalent) dipole moment Δα′ E. The results showed that the slowly fluctuating moment of m^21/2 is by far the most predominant one for the field orientation of the β-FeOOH particle, though the permanent dipole moment μ may not be completely excluded. The rotational relaxation time of the whole particle was evaluated from the decay signal, while the relaxation time for fluctuating ions was estimated from RPEB signal fitting. The sign of the steady-state birefringence for β-FeOOH suspensions was positive without exception under the present conditions. The birefringence signals in the steady state (δ/d) were proportional to the second power of the applied field strength (E) in the low field region; thus, the Kerr law was verified to hold for β-FeOOH suspensions. The specific Kerr constant was evaluated for each suspension by extrapolating the values of δ/d to zero field (E→0).     

Substituent Effects on Binding Constants of Carotenoids to n-Heptane/AOT Reverse Micelles

The absorption spectra of 6′-apo-β-caroten-6′-ol (1), 6′-apo-β-caroten-6′-oic acid (2), and ethyl 6′-apo-β-caroten-6′-oate (3) were analyzed in homogeneous media and in reversed micelles of AOT (sodium 1,4-bis(2-ethylhexyl) sulfosuccinate) in n-heptane. The possible solute–solvent interactions of these compounds were analyzed in pure solvents by Taft and Kamlet's solvatochromic comparison method. These carotenoids show sensitivity similar to that of medium polarity-polarizability as measured by π*. Moreover, the absorption spectra of carotenoid 3 and to much less extent carotenoid 2 display broadening of the visible bands induced by polar solvents characteristic of carotenoids that contain a carbonyl functional group in conjugation with the carbon–carbon π-electron system. They are also sensitive to the ability of the solvent to accept protons in a hydrogen bond interaction measured by β. This sensitivity follows the expected order: 2>1>3. In the reverse micellar system, while the spectra for 3 remain unchanged, the intensity of the absorption band characteristic of n-heptane for 1 and 2 decreases as the AOT concentration increases, and a new band develops. This new band is attributed to the solute bound to the micelle interface. These changes allowed us to determine the binding constant (K_b) between these compounds and AOT. At W₀=[H₂O]/[AOT]=0 the values of K_b of 326±5 and 6.2±0.3 were found for the acid 2 and the alcohol 1, respectively. The strength of binding is interpreted considering their hydrogen-bond donor ability and the solubility in the organic pseudophase. For 1K_bdecreases as W₀ is increased, while for 2 no variation was observed. These effects are discussed in terms of carotenoid–water competition for interfacial binding sites.     

Adsorption of 1,4-Benzenedithiol on Gold and Silver Surfaces: Surface-Enhanced Raman Scattering Study

The adsorption behavior of 1,4-benzenedithiol (1,4-BDT) on colloidal gold and silver surfaces has been investigated by means of surface-enhanced Raman scattering (SERS). 1,4-BDT chemisorbed dissociatively on both gold and silver surfaces but as mono- and dithiolate, respectively. Regardless of the bulk concentration of 1,4-BDT, only a monolayer was assembled on the silver surface with a flat orientation by forming two Ag–S bonds. On the gold surface, the monothiolate species,1,4-BDT⁻¹, appeared to assume a rather flat orientation at a very low surface coverage, but as the surface coverage was increased, the adsorbate took a perpendicular orientation. Furthermore, when the bulk concentration of 1,4-BDT was close to that required for a full-monolayer coverage limit, a band assignable to the S–S stretching vibration appeared at 536 cm⁻¹ in the gold sol SERS spectra. A separate ellipsometry measurement performed with vacuum-evaporated gold substrates revealed that up to tetralayers could be assembled on gold in 1 mM n-hexane solution of 1,4-BDT while at best a bilayer formed in either methanol or ethanol solution. The different adsorbate structure of 1,4-BDT on gold and silver was overall quite comparable to that of p-xylene-α,α′-dithiol.     

Silylating Agents Grafted onto Silica Derived from Leached Chrysotile

Silica from leached chrysotile fibers (SILO) was silanized with trialkoxyaminosilanes to yield inorganic–organic hybrids designated SILx (x=1–3). The greatest amounts of the immobilized agents were quantified as 2.14, 1.90, and 2.18 mmol g⁻¹ on SIL1, SIL2, and SIL3 for –(CH₂)₃NH₂,–(CH₂)₃NH(CH₂)₂NH₂, and –(CH₂)₃NH(CH₂)₂NH(CH₂)₂NH₂ groups attached to the inorganic support. The infrared spectra for all modified silicas showed the absence of the Si–OH deformation mode, originally found at 950 cm⁻¹, and the appearance of asymmetric and symmetric C–H stretching bands at 2950 and 2840 cm⁻¹. Other important bands associated with the organic moieties were assigned to ν_as(NH) at 3478 and ν_sym(NH) at 3418 cm⁻¹. The NMR spectrum of the solid precursor material suggested two different kinds of silicon atoms: silanol and siloxane groups, between −90 and 110 ppm; however, additional species of silicon that contain the organic moieties bonded to silicon at −58 and −66 ppm appeared after chemical modification. These modified silicas showed a high adsorption capacity for cobalt and copper cations in aqueous solution, in contrast to the original SILO matrix, confirming the unequivocal anchoring of silylating agents on the silica surface.     

Molecular Interactions in Mixed Monolayers of Octadecanoic Acid and Three Related Amphiphiles

Binary mixed monolayers of octadecanoic acid and three related amphiphilic compounds (octadecanamide, octadecylamine, octadecylurea) have been investigated at the air/water interface by surface pressure–area (Π–Â) isotherms and their resistances to water evaporation (r). In addition, the excess free energies of mixing (ΔG^E) were calculated using the Goodrich method. Both the ln r vs x and ΔG^E vs x plots exhibit marked deviations from linearity, indicating a high degree of miscibility and nonideal behavior of the components in the mixed films. For all of these binary systems the excess free energies of mixing have been found to be minimum for a certain composition corresponding almost to a maximum in evaporation resistances. Weak interactions were detected in octadecanoic acid/octadecanamide monolayers, whereas significant condensation effects were observed in 1 : 1 mixed films containing octadecanoic acid and octadecylamine. This is attributed to an acid–base equilibrium followed by the formation of a well-ordered arrangement of COO⁻ and NH₃⁺ head groups bound to each other by electrostatic forces. The unusual polymorphism of octadecylurea monolayers could be influenced by adding small amounts of octadecanoic acid. The formation of the low-temperature phase (β-phase) is completely suppressed, if the acid content exceeds 8 mol%. The octadecanoic acid seems to induce the formation of the high-temperature phase (α-phase), which is characterized by a vertical orientation of the hydrocarbon chains.     

Dielectrophoretic behavior of latex nanospheres: low-frequency dispersion

The electrostatic manipulation of nanoparticles using nonuniform electric fields (dielectrophoresis) has proved a useful method of investigating the movement of charge around colloidal particles. While previous work has explained many of the ways in which particle behavior deviates from that predicted by classical Maxwell-Wagner interfacial polarization theory, there exists an additional, anomalous polarization mechanism observed in media of high conductivity, causing an unexpected observation of positive dielectrophoresis. Here this is suggested that this may be explained in terms of the polarization of the Stern layer.     

Nitrogen Adsorption Studies of PAN-Based Activated Carbon Fibers Prepared by Different Activation Methods

Polyacrylonitrile (PAN)-based activated carbon fibers (ACFs) prepared by various activation methods were characterized using low-temperature nitrogen adsorption over a wide relative pressure from 10⁻⁶ to 1. Nitrogen adsorption is a standard tool for determination of porous structure parameters. In the present work, we carried out extensive adsorption studies of a series of PAN-ACFs activated by different methods. It was shown that the high-resolution α_S plot provided valuable information about structural properties of samples under study. The pore size distributions of samples under study were calculated by employing the regularization method according to density functional theory. By these analyses, the pore development and the dominant pores of samples prepared by different methods can be clearly observed. Moreover, the adsorption measurement could provide profound insight into the structural heterogeneity of the ACFs.     

Dynamic electrophoretic mobility of a concentrated dispersion of particles with a charge-regulated surface at arbitrary potential

The dynamic electrophoretic mobility of a concentrated dispersion of biocolloids such as cells and microorganisms is modeled theoretically. Here, a biological particle is simulated by a particle, the surface of which contains dissociable functional groups. The results derived provide basic theory for the quantification of the surface properties of a biocolloid through an electroacoustic device, which has the merit of making direct measurement on a concentrated dispersion without dilution. Two key parameters are defined to characterize the phenomenon under consideration: the first, A, is associated with the pH of the dispersion, and the second, B, is associated with the equilibrium constant of the dissociation reaction of the functional group. We show that if A is large and/or B is small, the surface potential is high, and the effect of double-layer polarization becomes significant. In this case the dynamic electrophoretic mobility may have a local maximum and a phase lead as the frequency of the applied electric field varies. Due to the hydrodynamic interaction between neighboring particles, the dynamic electrophoretic mobility decreases with the concentration of dispersion.     

H(2)O Outgassing Properties of Fumed and Precipitated Silica Particles by Temperature-Programmed Desorption

Temperature-programmed desorption was performed at temperatures up to 850 K on as-received fumed and precipitated silica particles. Physisorbed water molecules on both types of silica had activation energies in the range of 38–61 kJ/mol. However, the activation energies of desorption for chemisorbed water varied from 80 to >247 kJ/mol for fumed silica, Cab-O-Sil-M-7D, and 96 to 155 kJ/mol for precipitated silica, Hi-Sil-233. Our results suggest that physisorbed water can be effectively pumped away at room temperature (or preferably at 320 K) in a matter of hours. Chemisorbed water with high activation energies of desorption (>126 kJ/mol) will not escape silica surfaces in 100 years even at 320 K, while a significant amount of the chemisorbed water with medium activation energies (80–109 kJ/mol) will leave the silica surfaces in that time span. Most of the chemisorbed water with activation energies <126 kJ/mol can be pumped away in a matter of days in a good vacuum environment at 500 K. We had previously measured about 0.1–0.4 wt% of water in silica-reinforced polysiloxane formulations containing 21% Cab-O-Sil-M-7D and 4% Hi-Sil-233. Comparing present results with these formulations, we conclude that the adsorbed H₂O and the Si–OH bonds on the silica surfaces are the major contributors to water outgassing from these types of silica-filled polymers.     

A Phenomenon of the Change in Particle Drift Velocity Direction in High-Field Electrophoresis

The sign–alternating electric field in rectangular impulses has been used to eliminate linear electrophoresis and to study nonlinear electrophoresis in water at strong fields. We found out that the particle drift velocity could change its direction with the growth of the strength of the field. This new phenomenon has obtained its explanation in the framework of the Debye–Hückel theory of strong electrolyte where we consider a particle as a “heavy” effective ion and take into account all relevant nonlinear effects, grounding ourselves on basic physics. With the help of our theory we have succeeded in good fitting of our experimental data on black oil and Al₂O₃ particles in distilled water using reasonable values for the basic parameters such as the Debye screening length.     

The Heavy-Atom Effect on the Photophysics of Aromatic Hydrocarbons in the Presence of Solid Clays

The exchange of the original cation present on a Laponite clay (usually Na⁺) for heavy atoms such as Rb⁺, Cs⁺, and Tl⁺ significantly alters the emission characteristics of some aromatic hydrocarbons (p-terphenyl, naphthalene, pyrene, and biphenyl). The increase of the atomic mass of the cation induces a decrease of the fluorescence emission simultaneous with an increase of the emission in the region of lower energies of the spectra, ascribed to the phosphorescence of those hydrocarbons. Time-resolved experiments for the pyrene–clay system showed a decrease of singlet lifetimes for the heavier atoms. Hydrocarbon aggregates were also detected from both the emission spectra and the time-resolved studies. The “excimer-like” emission showed longer lifetimes (10–25 ns) than the monomolecular hydrocarbons (1–3 ns), as already found for other similar systems. The amount of aggregates increased for the heavier cations due to the smaller surface available on the clay particles. Experiments increasing the amount of Tl⁺ in samples containing a constant concentration of naphthalene allowed evaluation of the distance between the heavy atoms and the probe on the clay surface. The Perrin model treatment was used and resulted in approximately R₀=9.2 Å.     

Influence of Sodium Periodate and Tyrosinase on Binding of Alginate to Adlayers of Mytilus edulis Foot Protein 1

Mytilus edulis foot protein 1 (Mefp-1) is the most well-characterized component of this sea mussel's adhesive plaque. The plaque is a condensed, heterogeneous mixture consisting of a large proportion of cross-linked biopolymers that bonds the mussel to a chosen mooring. Mefp-1 is densely populated with lysine and -3,4-dihyroxyphenylalanine ( -dopa) residues incorporated into a repeating amino acid sequence motif. It has been proposed that one plaque cross-linking reaction is the nucleophilic addition of the ε-amino groups of the lysine residues into the oxidized catechol (o-diphenol) functionality (quinone) of the -dopa residues. In order to determine if this reaction occurs in adlayers of Mefp-1, a previously developed assay for ε-amino groups was applied. Adlayers of Mefp-1 were exposed to an oxidant, either the enzyme, mushroom tyrosinase, or sodium periodate. Binding of alginate to adlayers was used to probe for accessibility of ε-amino groups. It was found that lysine residues lose the ability to bind alginate after exposure to sodium periodate, but that this loss is not clearly due to a reaction with -dopa residues. There is a slight decrease of binding of alginate to adlayers of Mefp-1 exposed to either active or thermally deactivated mushroom tyrosinase, probably due to the obstruction of binding sites by bound enzyme. Adsorption kinetics of mushroom tyrosinase onto adlayers of Mefp-1 for active and thermally inactivated enzyme were nearly identical. Attenuated total reflection Fourier transform infrared spectroscopy was used to characterize these interactions at a germanium (Ge) interface.     

Effects of Nonionic and Mixed Cationic-Nonionic Micelles on the Rate of Alkaline Hydrolysis of 4-Nitrophthalimide

Pseudo-first-order rate constants (k_obs) for alkaline hydrolysis of 4-nitrophthalimide show a monotonic decrease with increase in [C₁₂E₂₃]_T (total concentration of Brij 35) at constant [CH₃CN] and [NaOH]. This micellar effect is explained in terms of a pseudophase micelle model. The rate of hydrolysis becomes too slow to monitor at [C₁₂E₂₃]_T≥0.03 M in the absence of cetyltrimethylammonium bromide (CTABr) and at [C₁₂E₂₃]_T≥0.04 M in the presence of 0.006–0.02 M CTABr at 0.01 M NaOH. The plots of k_obs versus [C₁₂E₂₃]_T show minima at 0.006 and 0.01 M CTABr, while such a minimum is not visible at 0.02 M CTABr.     

Aggregation and Polymerization of PEG-Based Macromonomers with Methacryloyl Group as the Only Hydrophobic Segment

Aggregation behavior in aqueous solution of a series of poly (ethylene glycol) (PEG)-based macromonomers with methacryloyl group as the only hydrophobic segment has been investigated using surface tension, steady-state and time-resolved fluorescence spectroscopy using pyrene as a probe, and small-angle neutron scattering techniques. The general formula of these macromonomers is CH₂=C(CH₃)–CO–O–E_m–CH₃, where E is the ethylene glycol unit and m=8 (ME₈), 18 (ME₁₈), 49 (ME₄₉), and 120 (ME₁₂₀). The results indicate that a macromonomer with 8 ethylene glycol units forms as an aggregate above a certain critical concentration, which can be defined as critical aggregation concentration. The observed high value of I₁/I₃ in pyrene emission spectra at the interface of these aggregates and the inability to scatter a neutron beam by these aggregates indicate that the hydrophobic cluster formed by this macromonomer is remarkably solvated. ME₁₈ has a tendency to aggregate but others do not form any hydrophobic cluster. The homopolymerization behaviors of these macromonomers in an aqueous medium at 70°C are consistent with these possibi- lities.     

Activity and Conformation of Yeast Alcohol Dehydrogenase (YADH) Entrapped in Reverse Micelles

Yeast alcohol dehydrogenase (YADH) solubilized in reverse micelles of aerosol OT (i.e., AOT or sodium bis (2-ethyl hexyl) sulfosuccinate) in isooctane has been shown to be catalytically more active than that in aqueous buffer under optimum conditions of pH, temperature, and water content in reverse micelles. Studies of the secondary structure conformational changes of the enzyme in reverse micelles have been made from circular dichroism spectroscopy. It has been seen that the conformation of YADH in reverse micelles is extremely sensitive to pH, temperature, and water content. A comparison has been made between the catalytic activity of the enzyme and the α-helix content in the conformation and it has been observed that the enzyme is most active at the maximum α-helix content. While the β-sheet content in the conformation of the entrapped enzyme was found to be dependent on the enzyme–micelle interface interaction, the α-helix and random coil conformations are governed by the degree of entrapment and the extent of rigidity provided by the micelle core to the enzyme structure.     

Effect of β-Cyclodextrin on the Photoinduced Charge Transfer in Sodium 1-Anilino-8-naphthalene Sulfate (ANS)/CdS Colloidal System

The S-center radical (ANS^·) of sodium 1-anilino-8-naphthalene sulfate (ANS) generated by photoinduced charge transfer in ANS/CdS and ANS/CdS/β-cyclodextrin(β-CD) systems has been studied by using spin trapping electron spin resonance techniques, UV-visible spectroscopic methods, and fluorescence spectroscopic methods. It was found that the S-centered radical (ANS^·) was produced by the charge transfer reaction between the ground state ANS and the positive hole h⁺(CdS) from the valence band of CdS colloids, by the charge transfer from the excited singlet state ¹ANS* to the conduction band of CdS colloids, or by both in the ANS/CdS and ANS/CdS/β-CD systems. The ESR signal intensity of the spin adduct (5,5′-dimethyl-1-pyrroline-N-oxide (DMPO)–ANS)^·, which is formed from ANS^· trapped by DMPO, in the latter system is 15 times stronger than that in the former system. The apparent association constants between ANS and CdS colloids in the absence and presence of β-CD determined from fluorescence quenching experiments are 1097 and 1606 M⁻¹, respectively. From ESR and fluorescence results, it is estimated that the efficiency of photoinduced charge transfer from ANS to CdS colloids in the ANS/CdS/β-CD system is 12.5 times that in the ANS/CdS system.     

Wetting Study of Hydrophobic Membranes via Liquid Entry Pressure Measurements with Aqueous Alcohol Solutions

A new concept of liquid entry pressure measurements is applied to study the hydrophobicity of microporous membranes for aqueous alcohol solutions. The effects of alcohol concentration, type of alcohol, and temperature on liquid entry pressure of the membrane have been studied. Two theoretical equations for the determination of membrane pore size have been proposed. The former equation was developed taking into account the deviation from the Laplace–Young equation due to the membrane structure by means of the structure angle. The latter equation was established considering only the range of alcohol concentration in which the dispersion component of liquid surface tension remains practically constant. Hydrophobicity has been expressed in terms of wetting surface tension, γ_L^w. Based on these measurements, the maximum concentration before the spontaneous wetting occurs would be predicted.