Determination of Trace Copper by Fluorescence Spectrophotometry Based on Cu(DP)2+ and Cu‐4.0‐Generations Polyamidoamine Dendrimers Catalyze Cu2+ to Oxidize Fluorescein

Abstract

Fluorescein can emit strong and stable fluorescence. Cu²⁺ can oxidize fluorescein, which causes the fluorescence signal to diminish. Cu(DP)²⁺ (DP refers to α,α′‐dipyridyl) and Cu‐GPD‐4.0 (GPD‐4.0 refers to 4.0‐generations polyamidoamine dendrimers) both can catalyze Cu²⁺ to oxidize fluorescein, which causes the fluorescence signal to diminish sharply. The ΔF is directly proportional to the content of copper. Based on the facts above, a new catalytic fluorescence spectrophotometry for the determination of trace copper using Cu(DP)²⁺ and Cu‐GPD‐4.0 was established. The linear range of this method is 0.040–28 pg mL^?1. The regression equation for working curve is ΔF=209.5+14.39 C_Cu ²⁺ (pg mL^?1), n=7; correlation coefficient is 0.991. The detection limit of this method is 1.0×10^?14 g mL^?1. After replicate measurement times, RSDs are 3.1% and 4.2% for samples containing 0.040 and 28 pg mL^?1 Cu²⁺, respectively. This method is rapid and precise with high sensitivity and good repeatability. The method has been applied to the determination of trace copper in tea and human hair with satisfactory results. Meanwhile, the mechanism for the determination of trace copper by catalytic fluorescence spectrophotometry using Cu(DP)²⁺ and Cu‐GPD‐4.0 was also discussed.     

Highly Selective and Sensitive Preconcentration of Mercury Ion and Determination by Cold Vapor Atomic Absorption Spectroscopy

Abstract

A simple and selective method based on a sodium dodecyl sulfate (SDS)–coated chromosorb P modified by 2‐mercaptobenzoxazole (MBO) has been developed to selectively separate and concentrate ultra trace amounts of mercury(II) ions for its highly sensitive measurement by cold vapor atomic absorption spectrometry (CVAAS).

The mercury ions were adsorbed quantitatively on SDS‐coated chromosorb due to its complexation with MBO, while the retained Hg²⁺ ions were then stripped from the column with minimal amounts of 2 M nitric acid in acetone. The eluting solution was sent to CV‐AAS for evaluating Hg²⁺ ion content and results indicate that the calibration curve was linear for Hg²⁺ ion in the range of 0.05–85.6 ng mL^?1 and 0.09–9.6 µg mL^?1 of Hg²⁺ ions. Maximum capacity of the SDS‐coated chromosorb modified with 40 mg of the ligand was found to be 498±30 µg of mercury(II), the limit of detection was 0.01 ng mL^?1, and enrichment factors were about 300, which make it suitable it for dilute solution analysis. The method was successfully applied to the determination of Hg²⁺ ion content in real samples.     

A novel method for the simple and simultaneous preconcentration of Pb2+, Cu2+ and Zn2+ ions with aid of diethylenetriamine functionalized SBA-15 nanoporous silica compound

A rapid method for the extraction and monitoring of nanogram level of Pb²⁺, Cu²⁺ and Zn²⁺ ions using uniform silanized mesopor (SBA-15) functionalized with diethylenetriamine groups and flame atomic absorption spectrometry (FAAS) is presented. The preconcentration factor of the method is 100 and detection limit of the technique is 5.5?ng?mL^?1 and 1.4?ng?mL^?1 and 0.1?ng?mL^?1 for Pb²⁺, Cu²⁺ and Zn²⁺ respectively. The time and the optimum amount of the sorbent, pH and minimum amount of acid for stripping of ions from functionalized SBA-15 were tested. The maximum capacity the functionalized SBA-15 was found to be 183.0 (±1.9) µg, 156.0 (±1.5) µg and 80.0 (±1.6) µg of Pb²⁺, Cu²⁺ and Zn²⁺/mg functionalized SBA-15, respectively.     

Colorimetric Determination of Lead Using Gold Nanoparticles

A combined homogeneous assay and colorimetric determination method using gold nanoparticles was developed for rapid determination of lead(II) in contaminated natural waters. The presence of lead(II) in the colloidal gold suspension causes a change in the absorbance of the suspension. An increase in the absorption property at 595 nm is accompanied by a change in the size of the gold nanoparticles. High concentrations of lead cause aggregation of the gold colloids. Colloidal gold nanoparticles were synthesized using tannic acid as the reducing agent; this reagent allowed selective determination of lead in 10 µL of water, with a detection limit of 310 ng mL^?1 with an analysis time of 5 min. The coefficient of variation for lead(II) within the working range of the assay (520 ng mL^?1–13 µg mL^?1) varied from 1.3% to 9.2%. The limit of detection using this method with a sample volume of 50 µL was 60 ng mL^?1. The coefficient of variation for lead over the working range of the determined concentrations (80 ng mL^?1–25 µg mL^?1) varied from 0.2% to 9.3%, while the values for the inter-day assay (n = 8) were less than 10%. The method was employed for the analysis of river, lake, marsh, and spring water; the recovery of lead was determined to be 72.5%–130% for 10 µL of water and 93.6%–114.7% for 50 µL.     

A new organic semiconducting polymer from Cu2+ chelate of poly(vinyl alcohol)and iodine

A new, easily processed, organic semiconductor was prepared from poly(vinyl alcohol) (PVA). The Cu²⁺ chelate of PVA exhibited excellent surface resistivity around 10³ Ω cm^?2 when modified with iodine. Favorable conditions for preparing the chelate effective for the conduction were investigated. The resistivity was significantly affected by the amounts of cupric salts and iodine, satisfactory results being given by more than 15 wt% of cupric salts and about 4 wt% of iodine. Effects of molecular weight of PVA and the chelate structure were also studied.     

Performance of the vanadium redox-flow battery (VRB) for Si-PWA/PVA nanocomposite membrane

The performance of Si-PWA/PVA nanocomposite membrane in vanadium redox-flow battery (VRB) is reported. Structurally, the membrane consisted of a dispersion of sub-micron-sized silica immobilized phosphotungstic acid (Si-PWA) inorganic ion-exchanging phase in the continuous phase of cross-linked poly(vinyl alcohol) (PVA). SEM micrographs indicated the defect-free top surface of membrane with similar morphology of Nafion-115. Good ion selectivity and availability of ion-exchangeable sites were observed as indicated by higher transport number (0.89) and ion-exchange capacity (IEC) (1.20 meq g^?1), respectively. Oxidative stability of the membrane was good in vanadium ion species (V⁴⁺, V³⁺, and V²⁺) but its stability in V⁵⁺ solution and Fenton’s reagent was slightly lower than Nafion-115. Vanadium ion permeability (0.69 × 10^?7 cm min^?1) of Si-PWA/PVA membrane was significantly lower than Nafion-115. Suitability for VRB with Si-PWA/PVA membrane was assessed from open-circuit voltage (OCV) decay which was lower compared to Nafion-115. Single-cell VRB with Si-PWA/PVA membrane exhibited lower voltage during charge and higher during discharge with excellent cyclic stability compared to VRB with Nafion-115.     

The States,Diffusion, and Concentration Distribution of Water in Radiation‐Formed PVA/PVP Hydrogels

Abstract

Hydrogels with various compositions of polyvinyl alcohol (PVA) and poly(1‐vinyl‐2‐ pyrrolidinone) (PVP) were prepared by irradiating mixtures of PVA and PVP in aqueous solutions with gamma‐rays from ⁶⁰Co sources at room temperature. The states of water in the hydrogels were characterized using DSC and NMR T₂ relaxation measurements and the kinetics of water diffusion in the hydrogels were studied by sorption experiments and NMR imaging. The DSC endothermic peaks in the temperature range ?10 to +10°C implied that there are at least two kinds of freezable water present in the matrix. The difference between the total water content and the freezable water content was referred to as bound water, which is not freezable. The weight fraction of water at which only nonfreezable water is present in a hydrogel with F_VP=0.19 has been estimated to be g_H2O/g_Polymer=0.375. From water sorption experiments, it was demonstrated that the early stage of the diffusion of water into the hydrogels was Fickian. A curve‐fit of the early‐stage experimental data to the Fickian model allowed determination of the water diffusion coefficient, which was found to lie between 1.5×10^?11 m² s^?1 and 4.5×10^?11 m² s^?1, depending on the polymer composition, the cross‐link density, and the temperature. It was also found that the energy barrier for diffusion of water molecules into PVA/PVP hydrogels was ≈24 kJ mol^?1. Additionally, the diffusion coefficients determined from NMR imaging of the volumetric swelling of the gels agreed well with the results obtained by the mass sorption method.     

Influence of urea and glycerol on functional properties of biodegradable PVA/xylan composite films

In recent years, numerous studies have focused on biodegradable plastics for agricultural applications. To improve the mechanical and hydrophobic properties, biodegradable xylan composite films containing poly(vinyl alcohol) (PVA) were successfully prepared by casting method in this work. A series of composite films at a PVA/xylan weight ratio of 3:1 under the addition of glycerol and urea were investigated. Influences of the urea and glycerol amounts on the functional properties of composite films such as hydrophilicity/hydrophobicity, water vapor permeability (WVP), mechanical properties, solubility and degradability were comparatively investigated. Results showed that increasing the glycerol amount led to a decrease in tensile strength and an increase in elongation at break and WVP, while the addition of 1 % urea in composite films without glycerol had a positive impact on improving the water resistance of composite films; the contact angle and WVP values reached 114.68° and 4.11 × 10^?11 g m^?1 s^?1 Pa^?1. Moreover, thermogravimetric analysis, FTIR and a scanning electron microscope were used to confirm the compatibility of the PVA and xylan components. FTIR analysis displayed the intensity of hydroxyl groups of films became stronger with increasing amounts of glycerol, while the opposite results were obtained with an increase of the amount of urea. These indicated that glycerol could improve the miscibility between PVA and xylan, and the addition of urea could enhance the water resistance of composite films.     

Square-Wave Anodic Stripping Voltammetry (SWASV) for the Determination of Ecotoxic Metals,Using a Bismuth-Film Electrode

This article reviews the use of square wave anodic stripping voltammetry for the simultaneous determination of ecotoxic metals (Pb, Cd, Cu, and Zn) on a bismuth-film (BiFE) electrode. The BiFE was prepared in situ on a glassy-carbon electrode (GCE) from the 0.1 mol L^?1 acetate buffer solution (pH 4.5) containing 200 µg L^?1 of bismuth (III). The addition of hydrogen peroxide to the electroanalytical cell proved beneficial for the interference-free determination of Cu (II) together with zinc, lead, and cadmium, using the BiFE. The experimental variables were investigated and optimized with the view to apply this type of voltammetric sensor to real samples containing traces of these metals. The performance characteristics, such as reproducibility, decision limit (CC_a), detection capability (CC_β), sensitivity, and accuracy indicated that the method holds promise for trace Cu²⁺, Pb²⁺, Cd²⁺, and Zn²⁺ levels by employment of Hg-free GCE with SWASV. CCa, and CCβ were calculated according to the Commission Decision of 12 August 2002 (2002/657/EC). Linearity was observed in the range 20–280 µg L^?1 for zinc, 10–100 µg L^?1 for lead, 10–80 µg L^?1 for copper, and 5–50 µg L^?1 for cadmium. Using the optimized conditions, the stripping performance of the BiFE was characterized by low limits of detection (LOD). Finally, the method was successfully applied in real as well as in certified reference water samples.     

Nanosized zinc and magnesium ferrites obtained from PVA–metal nitrates’ solutions

The paper presents a study regarding the possibility of obtaining zinc and magnesium ferrites starting from poly(vinyl alcohol)–metal nitrates solutions. By controlled heating of these solutions, a redox interaction takes place leading to the formation of some coordination compounds of the involved metal cations with the oxidation products of poly(vinyl alcohol) (PVA). FT-IR spectroscopy has evidenced the disappearance of the NO ₃ ^? anions at 140 °C due to the redox interaction with PVA. Thermal analysis evidenced the difference in the interaction of the individual metal nitrates and PVA and thus the particularity of the preparation of each ferrite. The thermal decomposition of the synthesized precursors was finished below 400 °C as resulting from both thermal analysis and FT-IR spectroscopy. The obtained ferrites powders consist of fine nanoparticle with diameters ranging from 10 to 30 nm for the powders annealed at 500 °C, as resulting from the SEM images. The specific surface area of the powders obtained at 500 °C was 32.2 m² g^?1 for ZnFe₂O₄ and 21.7 m² g^?1 for MgFe₂O₄, characteristic of nanoscaled powders. The increasing of the annealing temperature at 1,000 °C leads to sintering of both ferrites, more advanced in the case of zinc ferrite.     

Selective homogeneous liquid-liquid extraction and preconcentration of copper(II) into a micro droplet using a benzo-substituted macrocyclic diamide, and its determination by electrothermal atomic absorption spectrometry

A fast and reliable method was developed for the selective separation and preconcentration of Cu²⁺ ions using homogeneous liquid-liquid extraction using a novel benzo-substituted macrocyclic diamide, 5,6,7,8,9,10-hexahydro-2H-1,13,4,7,10-benzodioatriazacyclo-pentadecine-3,11(4 H,12 H)-dione, as a selective complexing agent. An aqueous solution of Zonyl FSA (FSA) was used as a phase-separation agent at pH 4.5. Electrothermal atomic absorption spectrometry was used for Cu²⁺ determination after preconcentration. The influences of pH, type and volume of the water-miscible organic solvent, concentration of FSA, concentration of the ligand and the effect of diverse ions were investigated. Factorial design and response surface methods were used for the optimization purposes. Under the optimum experimental conditions, 50 ng of Cu²⁺ in 5 mL aqueous sample could be extracted quantitatively into 76 µL of the sediment phase. The maximum preconcentration factor was 65. The calibration curve was linear in the concentration range 0.2 to 4.0 µg L^?1. The detection limit and relative standard deviation were 4 ng L^?1 and 4.6%, respectively. The method was successfully applied to the extraction and determination of Cu²⁺ in natural water samples.     

Improved Multianalyte Determination of the Intense Sweeteners Aspartame and Acesulfame‐K with a Solid Sensing Zone Implemented in an FIA Scheme

Abstract

A multianalyte flow‐through sensor is proposed for the simultaneous determination of aspartame (AS) and acesulfame‐K (AK) in tabletop sweeteners. The procedure is based on the transient retention of AK in the ion exchanger Sephadex DEAE A‐25 placed in the flow‐through cell of a monochannel flow injection analysis (FIA) set‐up using pH 2.70 ortophosphoric acid/sodium dihydrogen phosphate buffer 0.06 M as carrier. In these conditions AS is very weakly retained, which makes it possible to measure the intrinsic ultraviolet (UV) absorbance of first AS and then AK after desorption by the carrier itself. The applicable concentration range, the detection limit, and the relative standard deviation were the following: for AS, from 10 to 100 µg mL^?1; 5.65 µg mL^?1; 3.4% (at 50 µg mL^?1); and for AK, between 40 and 100 µg mL^?1; 11.9 µg mL^?1 and 1.61% (at 50 µg mL^?1). The method was applied and validated satisfactorily for the determination of AS and AK blends in tabletop sweeteners. The results were compared against an HPLC reference method.     

Determination of Explosives in Water Using Disposable Pipette Extraction and High Performance Liquid Chromatography

The use of disposable pipette extraction was examined for the simple and rapid determination of seven high explosives (cyclotrimethyl-enetrinitramine, cyclotetramethyl-enetetranitramine, 2,4,6-trinitrophenyl-methylnitramine, 2,4,6-trinitrotoluene, 2,4-dinitrotoluene, nitroglycerin, and pentaerythritol tetranitrate) in water. The current study involved the determination of slightly polar and nonpolar explosives in water with a reversed phase sorbent followed by high performance liquid chromatography. The method was based on a styrene divinylbenzene sorbent loosely placed inside a 5-mL pipette tip. Water samples were drawn into the tip and mixed with the sorbent. Air bubbles were also drawn through the tip following sample solution to enhance mixing. Because disposable pipette extraction uses small amounts of sorbent, minimal solvent is required to elute analytes and solvent evaporation is not necessary. The method provided rapid sample preparation, and required less than five minutes to extract 1.0 mL of water sample in the current study. Matrix-matched calibration was performed, and the limits of detection (LOD) were determined to be below 0.1 µg mL^?1 for all targeted explosives in water with an enrichment factor of two. Coefficients of determination (r²) were greater than 0.9990 for all studied explosives, and the recoveries ranged from 69.76% to 87.51%, 83.77% to 91.25%, and 83.62% to 98.99% for samples spiked at 0.25 µg mL^?1, 1.0 µg mL^?1, and 5.0 µg mL^?1, respectively. The relative standard deviations of recoveries at all spiked levels were below 8.97%. These results indicate that the disposable pipette extraction method provided good accuracy and precision for the determination of explosives in water.     

Studies on bound water in poly(vinyl alcohol). Hydrogel by DSC and FT-NMR

The phase transition of water bound in poly(vinyl alcohol)(PVA) hydrogel was measured by differential scanning calorimetry. The cross-link density calculated from the swelling ratio of PVA hydrogel ranged from 3 × 10^?5 to 1 × 10^?3 according to the total dose of ⁶⁰Co γ-ray irradiation. From the enthalpy of melting, it was found that water in PVA gel can be classified into at least three groups; ca. 1–1.5 mol non-freezing water, 5–6 mol freezing bound water, and the rest free water, corresponding to each hydroxyl group of PVA. The characteristic properties of polymer hydrogel were attributed to the large number of molecules of freezing bound water in the network. The amount of free water depended markedly upon cross-link density; however, it was not apparent in PVA gel with cross-link density >2.0 × 10^?4. The decreases in the nuclear magnetic resonance relaxation times of water and PVA were related to the cross-link density and were found to level off at a cross-link density 2.0 × 10^?4.     

Molecularly-Imprinted Materials for Potentiometric Transduction: Application to the Antibiotic Enrofloxacin

Enrofloxacin (ENR) is an antimicrobial used both in humans and in food producing species. Its control is required in farmed species and their surroundings in order to reduce the prevalence of antibiotic resistant bacteria. Thus, a new biomimetic sensor enrofloxacin is presented. An artificial host was imprinted in specific polymers. These were dispersed in 2-nitrophenyloctyl ether and entrapped in a poly(vinyl chloride) matrix. The potentiometric sensors exhibited a near-Nernstian response. Slopes expressing mV/Δlog([ENR]/M) varied within 48–63. The detection limits ranged from 0.28 to 1.01 µg mL^?1. Sensors were independent from the pH of test solutions within 4–7. Good selectivity was observed toward potassium, calcium, barium, magnesium, glycine, ascorbic acid, creatinine, norfloxacin, ciprofloxacin, and tetracycline. In flowing media, the biomimetic sensors presented good reproducibility (RSD of ± 0.7%), fast response, good sensitivity (47 mV/Δlog([ENR]/M), wide linear range (1.0 × 10^?5–1.0 × 10^?3 M), low detection limit (0.9 µg mL^?1), and a stable baseline for a 5 × 10^?2 M acetate buffer (pH 4.7) carrier. The sensors were used to analyze fish samples. The method offered the advantages of simplicity, accuracy, and automation feasibility. The sensing membrane may contribute to the development of small devices allowing in vivo measurements of enrofloxacin or parent-drugs.     

Identification and Quantification of Heterologous Compounds Parthenin and Organic Acids in Parthenium Hysterophorus L. Using HPLC-PDA-MS-MS

Parthenium hysterophorus L., is an obnoxious weed known for its environmental health hazards and medicinal uses. These characteristics are due to presence of sesquiterpene lactones and organic acids; therefore a rapid and sensitive analytical procedure using HPLC-PDA-MS-MS was developed and optimized for separation, identification, and quantification of parthenin and six organic acids. Separation and characterization of compounds was achieved on a RP-C18 column with 1% acetic acid in water (A) and acetonitrile (B) as a mobile phase at a flow rate of 0.6 mL min^?1 and by matching their UV and mass spectra with reference compounds. Six organic acids (ferulic acid, 0.1 mg g^?1 to coumaric acid, 13.6 mg g^?1) and parthenin (27.4 mg g^?1) were characterized within 26 minutes of chromatographic separation in plant extract. The calibration curves are linear with correlation coefficients from 0.985 to 0.998, limit of detection and quantification ranged between 1.0 µg mL^?1 (anisic acid) to 2.2 µg mL^?1 (parthenin) and 2.5 µg mL^?1 (coumaric acid) to 5.2 µ g mL^?1 (parthenin) and recovery ranged between 90.9% to 97.3%. To the best of our knowledge this is the first report for the simultaneous separation of parthenin and organic acids. The method is applicable for screening of commercial crops, medicinal plants, and their products which might be mixed with P. hysterophorus during harvesting period.     

Simultaneous voltammetric analysis of lead,copper and mercury ions by carbon paste electrode based on 1-(3-aminopropyl) imidazole modified polymer

In this study, a carbon paste electrode modified with a novel 1-(3-aminopropyl) imidazole functionalised crosslinked chlorosulfonated poly(styrene)-divinyl benzene polymer was used for selective and sensitive determination of the trace amounts of Pb²⁺, Cu²⁺ and Hg²⁺ ions by square wave anodic stripping voltammetry. The effect of some parameters such as paste composition, pH, preconcentration time, reduction potential and time, type of supporting electrolyte and potential scan rate on the determination of metal ions were investigated to find the optimal conditions. The effective open-circuit accumulation of the studied metal ions was succeeded only by the modification of the carbon paste electrode with functional polymer. For 6 min open-circuit preconcentration, the detection limit of Pb²⁺, Cu²⁺ and Hg²⁺ was found to be 5, 9 and 14 µgL^?1, respectively at 100 mVs^?1. The results confirmed that the lower concentration levels of these trace metal ions can be determined with the increase of preconcentration time and/or potential scan rate. Good detection limits and large dynamic concentration ranges were also obtained for their binary and ternary mixtures. The optimised method was successively applied to determine the concentration of Pb²⁺, Cu²⁺ ions in the tap water sample and Cu²⁺ ion in the waste water sample in the presence of possible interfering species (RSD<1%, recoveries 96–110% for 4 min preconcentration).     

Nonextractive Trace Level Simultaneous Determination of Mercury(II) and Zinc(II) in Environmental Samples with 2‐(5‐Bromo‐2‐pyridylazo)‐5‐diethylaminophenol and Cetylpyridinium Chloride

Abstract

A simple, rapid, selective, and sensitive method for the derivative spectrophotometric determination of Hg(II) and its simultaneous determination in the presence of Zn(II) using 2‐(5‐bromo‐2‐pyridylazo)‐5‐diethylaminophenol in the presence of cetylpyridinium chloride, a cationic surfactant, has been developed. The molar absorption coefficient and analytical sensitivity of the 1∶1 Hg(II) complex at 558 nm (λ_max) are 5.78×10⁴ L mol^?1 cm^?1 and 0.67 ng mL^?1, respectively. The detection limit of Hg(II) is 1.40×10^?2 ng mL^?1, and Beer's law is valid in the concentration range 0.05–2.40 µg mL^?1. Overlapping spectral profiles of Hg(II) and Zn(II) complexes in zero‐order mode interfere in their simultaneous determination. However, 0.10–2.00 µg mL^?1 of Hg(II) and 0.065–0.650 µg mL^?1 of Zn(II), when present together, can be simultaneously determined at zero cross point of the derivative spectrum, without any prior separation. The relative standard deviation for six replicate measurements of solutions containing 0.134 µg mL^?1 of Hg(II) and 0.620 µg mL^?1 of Zn(II) is 1.72 and 1.47%, respectively. The proposed method has successfully been evaluated for trace level simultaneous determination of Hg(II) and Zn(II) in environmental samples.     

Simultaneous Determination of Iron and Copper in Ethanol Fuel Using Nafion/Carbon Nanotubes Electrode

This work presents the analytical method development for iron and copper determination in ethanol fuel. This method was developed using stripping voltammetry with a glassy carbon electrode modified with Nafion/Carbon‐nanotubes. With linear sweep stripping voltammetry was achieved a limit of detection of 7.1×10^?7 mol L^?1 for Fe³⁺ and 5.1×10^?8 mol L^?1 for Cu²⁺. The amperometric sensitivities were 2.0×10⁶ µA mol^?1 L for Fe³⁺ and 2.8×10⁷ µA mol^?1 L for Cu²⁺. The recovery study showed that the method has good accuracy and repeatability, with recovery of 108 and 103 % for Fe³⁺ and Cu²⁺ respectively.     

Simultaneous Estimation of Atorvastatin Calcium, Ramipril and Aspirin in Capsule Dosage Form by RP-LC

A simple, sensitive, precise and accurate reversed phase liquid chromatographic method has been developed for the simultaneous estimation of atorvastatin (AT) calcium, ramipril (RA) and aspirin (AS) from capsule dosage form. The method was developed using a Phenomenex Luna C₁₈ (250 mm, 4.6 mm i.d., 5 µm) column with a mobile phase consisting of 0.1%, orthophosphoric acid buffer:acetonitrile:methanol (45:50:5 v/v/v), pH 3.3, at a flow rate of 1 mL min^?1. Detection was carried out with ultra-violet detection at 210 nm. The retention times were about 12.19, 2.35, and 3.95 min for AT calcium, RA and AS, respectively. The developed method was validated for linearity, accuracy, precision, limit of detection, limit of quantitation and robustness. The linearity ranges were 1–6 µg mL^?1 for AT calcium, 0.5–3 µg mL^?1 for RA and 7.5–45 µg mL^?1 for AS with mean recoveries of 100.59 ± 0.68, 100.62 ± 0.83 and 100.49 ± 0.73% for AT calcium, RA and AS, respectively. Limit of detection obtained were 29.85 ng mL^?1 for AT calcium, 4.71 ng mL^?1 for RA and 85.13 ng mL^?1 for AS. Impurity of salicylic acid was found in capsule dosage form at the retention time of about 4.84 min. The proposed method can be used for the estimation of these drugs in combined dosage forms.