Friction and wear properties of ZrO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> composite nanoparticles

In this article, the lubrication properties of ZrO₂/SiO₂ composite nanoparticles modified with aluminum zirconium coupling agent as additives in lubricating oil under variable applied load and concentration fraction were reported. It was demonstrated that the modified nanoparticles as additives in lubrication can effectively improve the lubricating properties. Under an optimized concentration of 0.1 wt%, the average friction coefficient was reduced by 16.24%. This was because the nanoparticles go into the friction zone with the flow of lubricant, and then the sliding friction changed to rolling friction with a result of the reduction of the friction coefficient.     

Ferroelectrical properties of SiO<Subscript>2</Subscript>-TGS nanocomposite

Dielectric properties of the composites based on nanodisperse silica hydrosol and ferroelectric triglycinesulfate (TGS) are investigated. The studies allow us to expect the presence of the ferroelectric state in the composites.     

Electrical conductivity and dielectric properties of SiO<Subscript>2</Subscript> nanoparticles dispersed in conducting polymer matrix

Electrical and dielectric properties of conducting polypyrrole–wide band gap silica (PPY–SiO₂) nanocomposites have been investigated as a function of temperature and frequency for different concentrations of polypyrrole. The average grain size of the nanocomposites is in the range of 40–80 nm. Impedance spectra reveal two distorted semicircles corresponding to grain and grain boundary effects. The magnitude of conductivity and its temperature variation are significantly different from polypyrrole and silica. A very large dielectric constant of about 4800 at 30 kHz and at room temperature has been observed for the highest concentration of silica. Inhomogeneous behavior of nanocomposites gives rise to high dielectric constant.     

Casimir friction force between a SiO<Subscript>2</Subscript> probe and a graphene-coated SiO<Subscript>2</Subscript> substrate

The possibility of mechanical detection of Casimir friction with the use of a noncontact atomic force microscope is discussed. A SiO₂ probe tip located above a graphene-coated SiO₂ substrate is subjected to the frictional force caused by a fluctuating electromagnetic field produced by a current in graphene. This frictional force will create the bend of a cantilever, which can be measured by a modern noncontact atomic force microscope. Both the quantum and thermal contributions to the Casimir frictional force can be measured using this experimental setup. This result can also be used to mechanically detect Casimir friction in micro- and nanoelectromechanical systems.     

Enhanced photoluminescence of Ca<Subscript>2</Subscript>Al<Subscript>2</Subscript>SiO<Subscript>7</Subscript>:Eu<Superscript>3+</Superscript> by charge compensation method

The effect of compensator on optical properties of Ca₂Al₂SiO₇:Eu³⁺ is systematically investigated by the X-ray powder diffraction, photo-luminescence (PL) properties and lifetime. It is obviously observed that the PL intensity of Eu³⁺ under 394 nm excitation increases in the order of Ca_1.86Eu_0.14Al₂SiO₇ (CAS), Ca_1.72Na_0.14Eu_0.14Al₂SiO₇ (CASNa) and Ca_1.86Eu_0.14Al_2.14Si_0.86O₇ (CASAl), the intensity of Eu³⁺ are 100%, 134%, 184%, and the lifetime of Eu³⁺ are 0.75 ms, 1.28 ms and 1.39 ms, respectively. A charge compensation model is proposed to explain the changes in the emission intensity and lifetime of Eu³⁺ in Ca₂Al₂SiO₇ with different compensation methods. PACS 78.55.-m; 61.72.Ji; 61.43.Gt; 42.70.-a; 74.62.Dh     

Si/SiO<Subscript>2</Subscript> core shell clusters probed by Raman spectroscopy

Using a pulsed microplasma source, clusters were produced through the ablation of a Si cathode and successive supersonic expansion. The Si cluster beam was deposited onto different substrates and the partial oxidation of the cluster surface avoided the growth of large agglomerates, preserving their nanocrystalline morphology. Micro-Raman spectroscopy was used for an accurate size diagnosis of the deposited nanoparticles. The size of the Si dots ranges between 2 and about 15 nm. The Si dots appear to have a Si oxide shell, as confirmed also by structural and compositional analysis through transmission electron microscopy and atomic force microscopy. Double Raman peaks were attributed to small Si agglomerates having a thin substoichiometric Si-O interface.     

RETRACTED ARTICLE: Refractive-index tailoring and morphological evolutions in Gd<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> and ZrO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite thin films

Refractive-index tailoring and morphological evolutions in two different thin film composite systems of gadolinia–silica (Gd₂O₃:SiO₂) and zirconia–silica (ZrO₂:SiO₂) deposited through reactive electron-beam codeposition processes are discussed in this research paper. For Gd₂O₃:SiO₂ the refractive-index tuning has been achieved from 1.45 to 2.18, whereas in the case of ZrO₂:SiO₂ the achieved tunable range is from 1.45 to 2.45 in the ultraviolet region. Under certain compositional mixings with lower silica fractions both the systems demonstrated relative microstructural and morphological densifications. Such evolutions were very successfully derived through phase-modulated ellipsometry and atomic force microscopy. The composition-dependent refractive-index tailoring and microstructural densifications have been investigated by adopting Tauc–Lorentz and single-effective-oscillator models. The morphological correlation functions have also very aptly supported such evolutions in these composite films. These experimental results indicate their favourable properties and applicability down to the extreme ultraviolet wavelength region of the electromagnetic spectrum. PACS 42.79.Wc; 78.66.-w; 78.20.Ci; 61.16.Ch; 42.70.-a;68.55.-a; 68.35.Bs; 81.15.Ef     

Preparation and investigation of composite SiO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> films

SiO₂-TiO₂ films [Si:Ti = 1:(0.06–2.3)] are obtained by the sol-gel method. The structural and photoluminescent properties of the films and powders heat-treated at different temperatures are studied. It is shown that after 700°C the composite consists of TiO₂ crystallites that are structurally similar to anatase and distributed in an amorphous SiO₂ matrix. The photoluminescence spectra have maxima at 450–500 nm. The photoluminescence intensity depends on the treatment temperature and TiO₂ content. __________ Translated from Zhurnal Prikladnoi Spektroskopii Vol. 74, No. 3, pp. 357–361, May–June, 2007.     

Erbium excitation in a SiO<Subscript>2</Subscript>: Si-nc matrix under pulsed pumping

The photoluminescence of Er³⁺ ions in a SiO₂ matrix containing silicon nanocrystals 3.5 nm in diameter is studied under resonant and nonresonant pulsed pumping with pulses 5 ns in duration. The effective erbium excitation cross section under pulsed pumping, σ_eff = 8.7 × 10^?17 cm₂, is close to that for nanocrystals. Comparison of the erbium photoluminescence intensity obtained for a SiO₂ matrix with and without nanocrystals made it possible to determine the absolute concentration of optically active nanocrystals capable of exciting erbium ions, the concentration of optically active erbium, and the average number of erbium ions excited by one nanocrystal. The study revealed that excitation transfer from one erbium ion to another is a relatively slow process, which accounts for the low efficiency of erbium ion excitation under pulsed pumping in a SiO₂ matrix containing silicon nanocrystals.     

Structure and optical properties of ZnSe/SiO<Subscript>2</Subscript> layered nanocomposites

Structure and optical properties of ZnSe/SiO₂ layered nanocomposites obtained using microwave magnetron sputtering have been studied. The nanocomposites are X-ray amorphous at relatively small thicknesses of the zinc selenide layers. When the thickness of the zinc selenide layers exceeds 20 Å, ZnSe/SiO₂ films contain SiO₂ amorphous phase and zinc selenide cubic nanocrystallites. It has been demonstrated that the thickness of zinc selenide layers affects the microstresses, refractive index, and band gap.     

Optical and magnetooptical properties of CoFeB/SiO<Subscript>2</Subscript> and CoFeZr/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> granular magnetic nanostructures

The optical and magnetooptical properties of the new granular nanocomposites (CoFeB)/(SiO₂) and (CoFeZr)/(Al₂O₃), which are grains of amorphous ferromagnetic alloys embedded in dielectric matrices, have been studied. The dependence of the optical, magnetooptical, and magnetic properties of the nanocomposites on their qualitative and quantitative composition, as well as on the conditions of their preparation, was investigated. Spectra of the dielectric functions ε = ε₁ ? iε₂ were obtained by the ellipsometric method in the range 0.6–5.4 eV. Above 4.2 eV, the absorption coefficient of the (CoFeB)/(SiO₂) composites was found to be close to zero for all magnetic-grain concentrations. The polar Kerr effect measured at a photon energy of 1.96 eV in dc magnetic fields of up to 15 kOe reaches values as high as 0.25°–0.3° for these nanocomposites and depends only weakly on the conditions of preparation. On the other hand, the (CoFeZr)/(Al₂O₃) nanostructures reveal a considerable difference in the concentration dependences of the Kerr effect between samples prepared in a dc magnetic field and in zero field.     

Mössbauer studies of magnetic Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/SiO<Subscript>2</Subscript> nanocomposites

A large variety of glass and glass ceramics may be obtained by sol-gel process from hydrolysis of tetraethoxysilane. The transformation involves hydrolysis and polycondensation reactions leading to the growth of clusters that eventually collide together to form a gel. The structure and properties of the final product have been found to be strongly dependent on the initial conditions of preparation. Silica nanocomposites based on Fe₂O₃/SiO₂ were prepared with the help of ultrasonic activation and subsequent annealing in nitrogen atmosphere or air with concentrations of iron oxide of about 20 to 30wt.%.     

Fabrication and structural characterization of Mg<Subscript>2</Subscript>SiO<Subscript>4</Subscript> nanowires

This article demonstrates the first reported successful synthesis of Mg₂SiO₄ nanowires. We have thermally heated Au-coated Si substrates, using a quartz tube with its inner surface pre-coated with MgO nanostructures. We have characterized the sample morphologies by using scanning electron microscopy and transmission electron microscopy (TEM). X-ray diffraction analysis and high-resolution TEM observation coincidentally revealed that the nanowires were crystalline with an orthorhombic Mg₂SiO₄ structure. We have discussed the possible growth mechanism of Mg₂SiO₄ nanowires. PACS 81.07.-b; 81.05.Zx; 61.10.Nz; 68.37.Hk; 68.37.Lp     

Facile growth of monolayer MoS<Subscript>2</Subscript> film areas on SiO<Subscript>2</Subscript>

Areas of single-layer MoS₂ film can be prepared in a tube furnace without the need for temperature control. The films were characterized by means of Raman spectroscopy, photoluminescence, low-energy electron diffraction and microscopy, and X-ray photoelectron spectroscopy and mapping. Transport measurements show n-doped material with a mobility of 0.26 cm² V^-1 s^-1.     

A computer study of the Raman spectra of the (GaN)<Subscript>129</Subscript>, (SiO<Subscript>2</Subscript>)<Subscript>86</Subscript>, and (GaN)<Subscript>54</Subscript>(SiO<Subscript>2</Subscript>)<Subscript>50</Subscript> nanoparticles

The Raman spectra of the (GaN)₁₂₉, (SiO₂)₈₆, and (GaN)₅₄(SiO₂)₅₀ nanoparticles were calculated using the molecular dynamics method. The spectrum of (SiO₂)₈₆ had three broad bands only, whereas the Raman spectrum of (GaN)₁₂₉ contained a large number of overlapping bands. The form of the Raman spectrum of (GaN)₅₄(SiO₂)₅₀ was determined by the arrangement of the GaN and SiO₂ components in it. The nanoparticle with a GaN nucleus had a continuous fairly smooth spectrum over the frequency range 0 ≤ ω ≤ 600 cm⁻¹, whereas the spectrum of the nanoparticle with a SiO₂ nucleus contained well-defined bands caused by vibrations of groups of atoms of different kinds and atoms of the same kind.     

Synthesis and nanostructural investigation of TiO<Subscript>2</Subscript> nanorods doped by SiO<Subscript>2</Subscript>

TiO₂ Nano rods can be used as dye-sensitized solar cells, various sensors and photocatalysts. These nanorods are synthesized by a hydrothermal corrosion process in NaOH solution at 200°C using TiO₂ powder as the source material. In the present work, the synthesis of TiO₂ nanorods in anatase, rutile and Ti₇O₁₃ phases and synthesis of TiO₂ nanorods by incorporating SiO₂ dopant, using the sol–gel method and alkaline corrosion are reported. The morphologies and crystal structures of the TiO₂ nanorods are characterized using field emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD) study. The obtained results show not only an aggregation structure at high calcination temperatures with spherical particles but also Ti–O–Si bonds having four-fold coordination with oxygen in SiO^4 −.     

The enhanced catalytic degradation of SiO<Subscript>2</Subscript>/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/C@TiO<Subscript>2</Subscript> photo-Fenton system on p-nitrophenol

Heterogeneous photo-Fenton SiO₂/Fe₃O₄/C@TiO₂ (SFCT) catalyst with a core-multishell structure and a diameter of about 550 nm was successfully prepared and was characterized by scanning electron microscopy (SEM), TEM, XRD, Raman, and Fourier transform infrared (FT-IR). The results illustrated that anatase TiO₂ coexisted with rutile TiO₂, in which the anatase phase was the main crystal phase. In addition, the catalytic activity of SFCT catalyst had been evaluated in the catalytic degradation on p-nitrophenol (PNP). The influence factors on the PNP degradation, including SFCT component ratio (m _SFC/ m _TiO2), H₂O₂ dosage, solution pH, and PNP concentration, had been investigated. And the contrast experiments about the photo-Fenton catalytic mechanism revealed that the SFCT-2 catalyst possessed a superior activity in the neutral environment due to the optimal activity matching between Fe₃O₄ and TiO₂, and it exhibited the stable catalytic performance after five successive recycles. Therefore, the SFCT-2 catalyst had a promising application for the photo-Fenton degradation of organic contaminant.     

Electroluminescence in SiO<Subscript>2</Subscript> layers in various structures

Electroluminescence (EL) in an electrolyte-insulator-semiconductor system is used to study oxide layers in Si-SiO₂-Si₃N₄ and Si-SiO₂ structures prepared using various techniques. The EL spectra of all the structures contained the 2.7-eV emission band characteristic of the radiative relaxation of excited sililene centers. A comparative study of the conditions conducive to the formation of such luminescence centers in various structures containing SiO₂ layers was made, and their nature was refined.