可聚合二苯甲酮类光引发剂的合成及其光聚合性能研究

以4-(2,3-环氧丙氧基)二苯甲酮(EBP)和丙烯酸为原料,通过开环反应合成了含有不饱和双键的可聚合光引发剂4-(丙烯酸-2-羟基丙酯-3-氧基)二苯甲酮(AEBP).采用红外光谱(FT-IR)、核磁共振氢谱(¹HNMR)对其结构进行表征,利用紫外吸收光谱对AEBP的紫外吸收波长进行表征,通过实时红外(RT-IR)研究了AEBP引发丙烯酸酯单体的光聚合动力学.采用萃取法对比了BP与AEBP引发固化体系后的迁移性.结果表明,随AEBP浓度增加,单体最终转化率增加;当助引发剂N,N-二甲氨基苯甲酸-乙酯(EDAB)浓度为1.2%时,单体最终双键转化率最高;AEBP对双官能度单体的引发效率较之三官能度单体的好;聚合速率随光照强度的增强而变快;固化后AEBP的迁移性比传统的BP大大降低.     

二芳酮-可聚合胺紫外光引发1,6-己二醇二丙烯酸酯聚合的动力学研究

用Photo-DSC(光差热扫描)研究了一种可聚合胺助引发剂乙二醇-3-吗啡啉丙酸酯甲基丙烯酸酯(EGMPM)分别与二苯甲酮(BP)、4-(4-甲苯硫基苯基)苯基甲酮(BMS)、4-氯二苯甲酮(CBP)、4-氯甲基二苯甲酮(CMBP)、4-羟甲基二苯甲酮(HMBP)等二芳酮组成的光引发体系引发以1,6-己二醇二丙烯酸酯(HDDA)为单体的紫外光聚合动力学.考察二芳酮质量分数、聚合温度、光照强度对其光聚合动力学影响,并评价其引发效果;同时计算出了EGMPM/BP引发HDDA聚合体系的活化能.结果表明,二芳酮的质量分数增加时,反应达到最大反应速率的时间减少,单体的转化率也相应增加,单体聚合速率相应增大;相同质量分数(0.1%)的不同二芳酮,BMS体系达到最大反应速率的时间最短,单体转化率也最高;随着温度和光强的增加,单体最终转化率、最大反应速率增大,达到最大反应速率所需的时间减少.     

二苯酮-可聚合胺引发1,6-己二醇二丙烯酸酯的光聚合研究

以UV-Vis分光光度计法和Photo-DSC法分别研究了合成的3种可聚合胺类助引发剂DMPDA、EGDPM、EGMPM与二苯甲酮(BP)组成的引发体系的光化学初级过程及引发1,6-己二醇二丙烯酸酯(HDDA)的紫外光聚合动力学.考察了助引发剂胺的含量对BP的光化学初级过程和对引发HDDA光聚合动力学的影响,以及光强和温度对聚合动力学的影响.结果表明,随着胺含量的增加,BP的光化学初级反应速率增加,从而使体系的聚合反应速率增加.随着温度和光强的增加,单体最终转化率、最大反应速率增大,达到最大反应速率所需的时间减小.     

三官能度甲基丙烯酰氧基单体的合成与性能研究

用甲基丙烯酰氯分别与二乙醇胺和三乙醇胺反应合成了两种三官能度甲基丙烯酰氧基单体.以实时红外光谱(RT-IR)法研究了两种单体的光聚合动力学性质,考察了不同单体、不同引发剂和引发剂浓度、不同光强对聚合性能的影响,并采用动态力学分析仪(DMA)测试了光固化后材料的力学性能.结果表明,随着引发剂浓度的增大,单体转化率、最大反应速率都增大,随着光强的增大,单体转化率、最大反应速率都降低.与二苯甲酮(BP)相比,2-羟基-2-甲基-1-苯基丙酮(1173)对两种单体具有较好的引发效果.两种单体加入三缩四乙二醇双甲基丙烯酸酯(SR209)中后,对体系光固化后的产物力学性能有不同影响.     

2,2′-二邻甲氧基苯基-4,4′,5,5′-四苯基-1,2′-二咪唑复合光引发体系的光聚合动力学研究

本文研究了对2,2′-二邻甲氧基苯基-4,4′,5,5′-四苯基-1,2′-二咪唑(BMOIM)复合光引发体系引发聚合动力学过程.采用紫外光谱仪对引发剂、供氢体、增感剂在紫外区的吸收谱图进行了表征.利用实时红外光谱仪对复合光引发体系引发聚合动力学过程进行实时监测,考察了不同光强、引发剂浓度以及不同官能度单体对反应速率及最终双键转化率的影响.结果表明,在引发剂浓度为0.6%(质量分数)时,20s内双键转换率达到96%,随着引发剂浓度的提高,聚合速率增大.聚合速率以及最终双键转化率随着光强增大而增大;双官能团单体的最终双键转化率比三官能团单体的最终双键转化率要高.     

大分子量二苯甲酮光引发剂的合成及动力学研究

以4-羟基二苯甲酮(HBP)、甲苯-2,4-二异氰酸酯(TDI)、4,4′-二羟基二苯甲酮(DHBP)为原料,通过两步反应,合成了一种大分子量二苯甲酮光引发剂:HBP-TDI-DHBP-TDI-HBP(HTDTH).通过实时红外研究了HTDTH的光聚合动力学.结果表明,HTDTH是一种有效的光引发剂.采用HTDTH/胺光引发体系引发二缩三丙二醇二丙烯酸酯(TPGDA)聚合时,随着胺和引发剂浓度的增大,反应速率(R_p)和单体最终转化率(P)同时增大.     

基于α-羟烷基苯酮(HAPK)可聚合大分子光引发剂的合成及其引发三丙二醇双丙烯酸酯(TPGDA)光聚合动力学的研究

以α-羟烷基苯酮(HAPK)、甲苯-2,4-二异氰酸酯(TDI)、聚乙二醇600(PEG600)和丙烯酸-β-羟乙酯(HEA)为原料,通过3步反应,合成了一种可聚合大分子光引发剂:HAPK-TDI-PEG600-TDI-HEA(HTPTH).用IR对反应过程进行了监测.通过Photo-DSC研究了HTPTH引发三丙二醇双丙烯酸酯(TPG-DA)光聚合动力学,考察了光强、引发剂浓度对TPGDA光聚合动力学的影响.结果表明,随着引发剂浓度和光强的增大,最大反应速率对应的转化率、单体最终转化率、最大反应速率都增大,达到最大反应速率所需的时间减小.     

4-乙烯基-1-环己烯二环氧化物阳离子单体光聚合性能研究

本文用实时红外光谱研究了4-乙烯基-1-环己烯二环氧化物(TTA22)单体的光聚合性能。分别考察了光引发剂浓度、光源、光强及增感剂浓度对其光聚合性能的影响。选用3,4-环氧环己基甲酸-3′,4′-环氧环己基甲酯(TTA21)作为参照,比较了不同单体的光固化性能。结果表明,随着引发剂浓度以及光强的增加,环氧基转化率及转化速率随之增加。LED光源下单体的转化率和转化速率低于UV汞灯。对TTA22和TTA21光固化后材料的热稳定性进行分析,结果显示TTA21的热稳定性优于TTA22的。     

一种可聚合光引发体系及其性能研究

合成了一种可聚合双分子光引发体系——甲基丙烯酸-4-二苯酮甲酯(BPMM)光引发剂和甲基丙烯酸-3,4-亚甲基二氧基苯甲酯(MDBMM)助引发剂.采用含有水平样品支架的实时红外光谱仪(RTIR)监测光聚合动力学,动态力学分析仪(DMA)研究固化膜的机械性能.结果表明,聚合体系的聚合速率(Rp)和最终双键转化率(Pf)随MDBMM浓度的增加而增加,但是,随BPMM的浓度变化出现一最佳值(0.8%);相同的聚合条件下,与传统引发体系相比,BPMM/MDBMM虽然引发活性较差,但是其固化膜的Pf和玻璃化转变温度以及在37℃左右的储能模量与传统引发体系相近,并且MDBMM作为天然可食用植物化学成分衍生物的特点使其有可能适宜于在生物相容性要求较高的领域中应用.     

2-(4-甲氧基苯基)-4,6-双(三氯甲基)-S-三嗪光引发剂的合成及其光聚合动力学性能研究

以对甲氧基苯甲腈和三氯乙腈为原料合成了光引发剂2-(4-甲氧基苯基)-4,6-双(三氯甲基)-S-三嗪(MBTT),通过傅里叶红外光谱仪、核磁共振仪和紫外吸收光谱对所合成的产物结构进行了表征.并利用实时红外(RT-IR)对该引发剂进行了光聚合反应动力学研究,考察了单体、引发剂浓度和光强对引发速率及单体转化率的影响.结果表明,MBTT是一种高效的紫外光引发剂,在引发剂用量为0.1%时光聚合的单体转化率就能达到90%;随着光强的增大,单体的双键转化率和最大反应速率都增大,诱导期缩短;双丙烯酸酯类单体的双键转化率比三丙烯酸酯类单体的双键转化率要高.     

Synthesis and photopolymerization kinetics of benzophenone piperazine one‐component initiator

A one‐component type II photoinitiator (PDBP), based on 4‐hydroxybenzophenone (HBP), acryloyl chloride, and piperazine, was synthesized and its structure was confirmed by ¹H‐NMR. The photopolymerization kinetics of the photoinitiator was studied by real‐time Infrared spectroscopy (FT‐IR). It indicated that PDBP was a more effective photoinitiator than that of BP/triethylamine (TEA). The rate of polymerization, final conversion increased and the induction period shortened with increase in PDBP concentration, light intensity, and amine concentration. The kinetics of photopolymerization for TPGDA incorporating PDBP in the presence of different tertiary amines as the initiating system indicated that the PDBP/TEA combination exhibited the highest polymerization rates among the PDBP/amine combinations. Copyright © 2007 John Wiley & Sons, Ltd.     

The influence of temperature and photoinitiator concentration on photoinitiated polymerization of diacrylate monomer

The behavior of p-methoxybenzoyldiphenylphosphine oxide, previously synthesized, as a photoinitiator for the polymerization of diacrylate monomer, in the presence of 3% (w/w) tertiary amine (triethyl amine) as synergist additive, was studied. The influence of temperature in the range 30–90°C at 3% (w/w) photoinitiator concentration and the influence of the photoinitiator concentration in the range 0.5–3.5% (w/w) at 30°C was investigated by differential scanning photocalorimetry (photo-DSC). In all experiments the photopolymerization was performed at constant light intensity (3 mW cm⁻²). The maximum conversion was obtained at temperature of 90°C at 3% (w/w) photoinitiator concentration and 3% (w/w) triethyl amine. The optimal concentration of photoinitiator to obtain maximum conversion was 3% (w/w), at 30°C. No thermal polymerization occurred at higher temperature.     

Photopolymerization induced by a benzophenone derivative photoinitiator

A benzophenone derivative photoinitiator, HBP-TDI-HQ-TDI-HBP （HTCTH）, was synthesized based on 4-hydroxy benzophenone （HBP）, toluene-2,4-diisocyanate （TDI） and hydroquinone （HQ）. HTCTH was a more effective photoinitiator which had longer wavelength absorption in the UV-vis absorption spectra than the low molecular counterpart benzophenone （BP）. It showed that both rate of polymerization （Rp） and final conversion （P） increased with increase of amine and HTCTH concentration in photopolymerization.     

Novel,highly efficient polymeric benzophenone photoinitiator containing coinitiator moieties for photopolymerization

A novel polymeric photoinitiator P(MPBP‐co‐DMAEMA), bearing side‐chain benzophenone (BP) and coinitiator amine, was synthesized through free radical copolymerization of a polymerizable photoinitiator, 4‐[(4‐maleimido)phenoxy]benzophenone (MPBP), and a polymerizable coinitiator amine, N, N‐dimethylaminoethyl methacrylate (DMAEMA). In order to find out the influences of coinitiator amine on photopolymerization, a polymeric coinitiator amine, P(DMAEMA), was also synthesized for comparison. FT‐IR, ¹H NMR, and GPC analyses confirm the structures of polymers. The UV‐Vis spectra of polymeric photoinitiator P(MPBP‐co‐DMAEMA) and polymerizable photoinitiator MPBP are similar, and both exhibit high red‐shifted maximal absorption as compared with BP. The photopolymerization of 1,6‐hexanediol diacrylate (HDDA) and trimethylolpropane triacrylate (TMPTA), initiated by MPBP/DMAEMA, MPBP/P(DMAEMA), and P(MPBP‐co‐DMAEMA) systems, was studied by photo‐DSC. The results indicate that P(MPBP‐co‐DMAEMA) is most efficient for the polymerization of both HDDA and TMPTA, and MPBP/P(DMAEMA) is the least efficient of the three photoinitiating systems. Copyright © 2009 John Wiley & Sons, Ltd.     

One‐component photoinitiator based on benzophenone and sesamol

A new benzodioxole derivative, 4‐(1,3‐benzodioxol‐5‐yloxy) benzophenone (BPBDO), based on benzophenone and sesamol was precisely synthesized, and it can be used as a 1‐component type II photoinitiator. Elementary analysis, atmospheric pressure chemical ionization mass spectrometry, ¹H nuclear magnetic resonance, and ¹³C nuclear magnetic resonance studies revealed that the molecular structure of BPBDO consisted of both benzophenone (BP) and benzodioxole (BDO) structures. The laser flash photolysis experiments and electron spin resonance test indicated that the process of radicals generated from BPBDO after irradiation was similar to 3 processes of ethyl 4‐dimethylaminobenzoate and BP. The kinetics of photopolymerization of the photoinitiator was also studied by real‐time infrared spectroscopy. The oxygen content, light intensity, and viscosity of the monomer affected the decomposition (R_d) and polymerization rate, and the final double bond conversion was also studied. All the results suggest that BPBDO is a 1‐component photoinitiator that is an efficient photoinitiator for free radical polymerization. In contrast to typical dual‐component photoinitiators, eg, BP/ethyl 4‐dimethylaminobenzoate or BP/BDO, BPBDO does not require an additional amine coinitiator for the initiation and is applicable in nonamine resin systems.     

Novel PU‐type polymeric photoinitiator comprising side‐chain benzophenone and coinitiator amine for photopolymerization of PU acrylate

A novel diamine 3,5‐diamino‐4′‐phenoxylbenzophenone (DAPBP) was synthesized from the reaction of 3,5‐diamino‐4′‐chlorobenzophenone (DACBP) and phenol. Then through the polycondensation of DAPBP, toluene‐2,4‐diisocyanate (TDI), and N‐methyldiethanolamine (MDEA), we obtained a PU‐type polymeric photoinitiator containing side‐chain benzophenone (BP) and tertiary amine in the same macromolecule (PUSOA). Another polymeric photoinitiator without coinitiator amine in polymer chain (PUSO) was also synthesized for comparison. FT‐IR, ¹H NMR, and GPC analyses confirmed the structures of monomer and polymeric photoinitiators. The UV–Vis spectra of PUSOA, PUSO, and DAPBP are similar, and all exhibit the maximal absorption near 290 nm. ESR spectra indicate that PUSOA can generate active species most efficiently. The photopolymerization of PU acrylate, initiated by PUSOA, PUSO/MDEA, DAPBP/MDEA, and BP/MDEA, was studied by differential scanning photocalorimetry (photo‐DSC). The results show that the in‐chain coinitiator amine can significantly improve the photoefficiency of the polymeric photoinitiator and the PUSOA is more efficient for the polymerization of PU acrylate than its low‐molecular‐weight counterpart. Copyright © 2008 John Wiley & Sons, Ltd.     

Preparation of Fluorine-Containing Polyacrylate Emulsion by a UV-initiated Polymerization

A fluorine-containing polyacrylate emulsion was synthesized by a UV-initiated emulsion polymerization from methyl methacrylate (MMA) and hexafluorobutly methacrylate (HFMA) in the presence of 2-hydroxy-4-(2-hydroxyethoxy)-2-methyl-propiophenone (Irgacure 2959) as a hydrophilic photoinitiator at room temperature. The latex and films were characterized by Fourier transformed infrared (FT-IR) spectrometry, nuclear magnetic resonance (¹H-NMR, ¹⁹F-NMR) spectrometry, transmission electron microscopy (TEM), recycling gel permeation chromatography (GPC), dynamic light scattering (DLS), and contact angle (CA) analysis, respectively. The effects of photoinitiator and emulsifier concentration on the polymerization were discussed. Compared to the corresponding thermal polymerization, UV-initiated polymerization of the MMA/HFMA emulsion could be accomplished at a much higher speed. The polymerization conversion in UV-initiated polymerization reached 95% within 10 min at an emulsifier concentration of 0.6 wt%, photoinitiator concentration of 0.4 wt%, and monomer concentration of 10 wt%.     

1,3-Dioxine diphenyl as a novel initiator for free-radical photopolymerization

1,3-Dioxane diphenyl, a novel photoinitiator for free-radical polymerization, was synthesized and characterized. UV-Vis absorption spectroscopy was used to investigate its photochemical behavior during the photophysical process. The photopolymerization kinetics of 1,3-dioxane diphenyl was studied by realtime infrared spectroscopy. There was an optimum curing rate with the increase of 1,3-dioxane diphenyl concentration. Both the polymerization rate and final conversion increased with the increase in light intensity. 1,3-Dioxane diphenyl was the most efficient photoinitiator for tripropylene glycol diacrylate and other acrylate monomers. 1,3-Dioxane diphenyl was a more effective photoinitiator than benzophenone/ethyl-4-dimethylaminobenzoate.     

光引发阳离子聚合反应的研究——Ⅱ.硫鎓盐DPTS引发乙烯基正丁醚光聚合动力学

以二苯基-4-苯硫基代苯基硫鎓盐(DPTS)为光引发剂,研究了乙烯基正丁醚的本体和溶液光聚合。在本体聚合中,聚合速率(R_p)与引发剂浓度成正比;在15～35℃范围内,聚合活化能几乎为零。分别以CHCl₃(CH₂Cl)₂和C₆H₅Cl作溶剂的溶液聚合,其R_p均比本体聚合者大,同时单体浓度对R_p的影响则表现出复杂的关系。根据普遍接受的硫鎓盐光解机理并假设溶剂和单体均可不同程度地参与引发反应,解释了溶液聚合中单体影响的动力学规律。