Natural convection in power-law fluids from two square cylinders in tandem arrangement at moderate Grashof numbers

In this work, free convective flow and heat transfer in power-law fluids from two heated square cylinders in tandem arrangement is studied. The governing differential equations have been solved numerically over wide ranges of Grashof number, 10 ≤ Gr ≤ 1,000, Prandtl number, 0.71 ≤ Pr ≤ 50 and power-law index, 0.4 ≤ n ≤ 1.8. In order to elucidate the extent of inter-cylinder interaction, the non-dimensional inter-cylinder spacing, L/d is varied in the range, 2 ≤ L/d ≤ 6. The results are interpreted in terms of streamline and isotherm contours in the proximity of two cylinders to gain physical insights into the nature of flow. At the next level, the distribution of the local Nusselt number along the surface of the cylinders is presented. At the minimum inter-cylinder spacing due to the intense interference, the downstream cylinder contributes much less to the overall heat transfer whereas it experiences much higher hydrodynamic drag than the upstream cylinder. Broadly, the local and average Nusselt number for both cylinders show a positive dependence on both Grashof and Prandtl numbers. Also, all else being equal, shear-thinning fluid behaviour promotes the rate of heat transfer and shear-thickening fluid behaviour impedes it. Finally, the present numerical results have been correlated by using simple forms of equations thereby enabling the estimation of Nusselt number in a new application.     

Mixed convection heat transfer from three heated square cylinders in cross-flow at low Reynolds numbers

This paper presents the effects of cross buoyancy and Prandtl number on the flow and heat transfer characteristics around three equal isothermal square cylinders arranged in a staggered configuration within an unconfined medium. Transient two-dimensional numerical simulations are performed with a finite volume code based on the SIMPLEC algorithm in a collocated grid system. The pertinent dimensionless parameters, such as Reynolds, Prandtl and Richardson numbers are considered in the range of 1 ≤ Re ≤ 30, 0.7 ≤ Pr ≤ 100 and 0 ≤ Ri ≤ 1. The representative streamlines, vortex structures and isotherm patterns are presented and discussed. In addition, the overall drag and lift coefficients and average Nusselt numbers are determined to elucidate the effects of Reynolds, Prandtl and Richardson numbers on flow and heat transfer. The flow is observed to be steady for all the ranges of parameters considered. The drag coefficient is found to decrease with Re (for Ri = 0) and Ri at low Pr, whereas it increases with Pr at higher Ri. The lift coefficient decreases with Ri at low Pr and increases with Pr at higher Ri. The time and surface average cylinder Nusselt number is found to increase monotonically with Re as well as Pr while it remains almost insensitive to Ri at low Pr.     

Entropy generation and natural convection in square cavities with wavy walls

The aim of the present work is to study the entropy generation in the natural convection process in square cavities with hot wavy walls through numerical simulations for different undulations and Rayleigh numbers, while keeping the Prandtl number constant. The results show that the hot wall geometry affects notably the heat transfer rate in the cavity. It has been found in the present numerical study that the mean Nusselt number in the case of heat transfer in a cavity with wavy walls is lower, as compared to heat transfer in a cavity without undulations. Based on the obtained dimensionless velocity and temperature values, the distributions of the local entropy generation due to heat transfer and fluid friction, the local Bejan number, and the local entropy generation are determined and plotted for different undulations and Rayleigh numbers. The study is performed for Rayleigh numbers 10³ < Ra < 10⁵, irreversibility coefficients 10^?4 < φ < 10^?2, and Prandtl numbers Pr = 0.71. The total entropy generation is found to increase with increasing undulation number.     

A numerical study of the steady forced convection heat transfer from an unconfined circular cylinder

Forced convection heat transfer from an unconfined circular cylinder in the steady cross-flow regime has been studied using a finite volume method (FVM) implemented on a Cartesian grid system in the range as 10 ≤ Re ≤ 45 and 0.7 ≤ Pr ≤ 400. The numerical results are used to develop simple correlations for Nusselt number as a function of the pertinent dimensionless variables. In addition to average Nusselt number, the effects of Re, Pr and thermal boundary conditions on the temperature field near the cylinder and on the local Nusselt number distributions have also been presented to provide further physical insights into the nature of the flow. The rate of heat transfer increases with an increase in the Reynolds and/or Prandtl numbers. The uniform heat flux condition always shows higher value of heat transfer coefficient than the constant wall temperature at the surface of the cylinder for the same Reynolds and Prandtl numbers. The maximum difference between the two values is around 15–20%.     

Numerical computation of natural convection in an isosceles triangular cavity with a partially active base and filled with a Cu–water nanofluid

This paper discusses the results of a study related to natural convection cooling of a heat source located on the bottom wall of an inclined isosceles triangular enclosure filled with a Cu water-nanofluid. The right and left walls of the enclosure are both maintained cold at constant equal temperatures, while the remaining parts of the bottom wall are insulated. The study has been carried out for a Rayleigh number in the range 10⁴ ≤ Ra ≤ 10⁶, for a heat source length in the range 0.2 ≤ ε ≤0.8, for a solid volume fraction in the range 0 ≤ ?≤0.06 and for an inclination angle in the range 0° ≤ δ≤45°. Results are presented in the form of streamline contours, isotherms, maximum temperature at the heat source surface and average Nusselt number. It is noticed that the addition of Cu nanoparticles enhances the heat transfer rate and therefore cooling effectiveness for all values of Rayleigh number, especially at low values of Ra. The effect of the inclination angle becomes more noticeable as one increases the value of Ra. For high Rayleigh numbers, a critical value for the inclination angle of δ = 15° is found for which the heat source maximum temperature is highest.     

Numerical investigation of flow and combined natural-forced convection from an isothermal square cylinder in cross flow

Unsteady flow and heat transfer from a horizontal isothermal square cylinder is studied numerically using a three-dimensional computational model to investigate the influence of buoyancy on the forced flow and heat transfer characteristics. The numerical model is based on a horizontal square cylinder subjected to laminar fluid flow in an unconfined channel. The governing equations in 3D form are solved using a fractional step method based on the finite difference discretization in addition to a Crank–Nicholson scheme employed to the convective and the viscous terms. Two working fluids–air (Pr = 0.7) and water (Pr = 7)–are considered, and the flow and heat transfer simulations were carried out for the Reynolds and Richardson numbers in the intervals 55 ≤ Re ≤ 250 and 0 ≤ Ri ≤ 2, respectively. The flow characteristics such as time-averaged drag/lift, rms drag/rms lift coefficients as well as Strouhal number were computed. The heat transfer from the cylinder is assessed by mean Nusselt number (and rms Nusselt number) over the total heated cylinder walls. As the buoyancy increases, the mass and the velocity of the fluid flowing underneath the cylinder increases. The fluid is injected into the near wake region with an upward motion which significantly alters the flow field in the downstream as well as upstream regions. The effects of Reynolds, Richardson and Prandtl numbers on the flow field and temperature distributions are discussed in detail. It is shown that the flow and heat transfer characteristics are influenced more for air than water. To fill the void in the literature, useful empirical correlations of practical importance are derived for pure forced and pure natural as well as mixed convection. The mixed convection correlations, in terms of the ratio of pure forced convection, are also developed, and their implications are discussed.     

Turbulent heat transfer characteristics of water flow in a rotating pipe

Large-Eddy-Simulation of turbulent heat transfer for water flow in rotating pipe is performed, for various rotation ratios (0 ≤ N ≤ 14). The value of the Reynolds number, based on the bulk velocity and pipe diameter, is Re = 5,500. The aim of this study is to examine the effect of the rotating pipe on the turbulent heat transfer for water flow, as well as the reliability of the LES approach for predicting turbulent heat transfer in water flow. Some predictions for the case of non-rotating pipe are compared to the available results of literature for validation. To depict the influence of the rotation ratio on turbulent heat transfer, many statistical quantities are analyzed (distributions of mean temperature, rms of fluctuating temperature, turbulent heat fluxes, higher-order statistics). Some contours of instantaneous temperature fluctuations are examined.     

Enhanced heat transfer performances of molten salt mixed convection in a vertical annular duct

The mixed convection heat transfer of upward molten salt flow in a vertical annular duct is experimentally and numerically studied. The heat transfer performances of mixed convection are measured under Reynolds number 2,500–12,000 and inlet temperature 300–400 °C, and Nusselt number of molten salt flow with cooled inner wall monotonically increases with buoyancy number. The mixed convection is further simulated by low-Reynolds number k-ε model and variable properties, and the heat transfer tendency from numerical results agrees with that from experiments. At low Reynolds number, the natural convection plays more important role in the mixed convection. As the buoyancy number rises, the thickness of flow boundary layer near the inner wall increases, while the effective thermal conductivity remarkably rises, so the enhanced heat transfer of mixed convection is mainly affected by the effective thermal conductivity due to turbulent diffusion.     

Analysis of viscous dissipation effect on thermal entrance heat transfer in laminar pipe flows with convective boundary conditions

Consideration is given to the influence of viscous dissipation on the thermal entrance region laminar pipe flow heat transfer with convective boundary condition. The Eigenfunction series expansion technique is employed to solve the governing energy equation. The results for axial distributions of dimensionless bulk and wall temperatures, local Nusselt number as well as modified local Nusselt number are presented graphically forNu ₀ =0.1, 2, and 100. The complicated variations of conventional local Nusselt number is due to the inappropriate definition of conventional heat transfer coefficient in this problem. A modified local heat transfer coefficient, based on the difference of bulk fluid temperature and wall temperature, is introduced. Its value can clearly indicate the extent and the direction of heat exchange between the fluid in the pipe and the ambient. The effects of outside Nusselt number are also investigated. Significant viscous dissipation effects have been observed for large Br.     

Numerical solutions to heat transfer of nanofluid flow over stretching sheet subjected to variations of nanoparticle volume fraction and wall temperature

The numerical analysis of heat transfer of laminar nanofluid flow over a fiat stretching sheet is presented. Two sets of boundary conditions （BCs） axe analyzed, i.e., a constant （Case 1） and a linear streamwise variation of nanopaxticle volume fraction and wall temperature （Case 2）. The governing equations and BCs axe reduced to a set of nonlinear ordinary differential equations （ODEs） and the corresponding BCs, respectively. The dependencies of solutions on Prandtl number Pr, Lewis number Le, Brownian motion number Nb, and thermophoresis number Nt are studied in detail. The results show that the reduced Nusselt number and the reduced Sherwood number increase for the BCs of Case 2 compared with Case 1. The increases of Nb, Nt, and Le numbers cause a decrease of the reduced Nusselt number, while the reduced Sherwood number increases with the increase of Nb and Le numbers. For low Prandtl numbers, an increase of Nt number can cause to decrease in the reduced Sherwood number, while it increases for high Prandtl numbers.     

Heat transfer performance comparison of steam and air in gas turbine cooling channels with different rib angles

Using steam as working fluid to replace compressed air is a promising cooling technology for internal cooling passages of blades and vanes. The local heat transfer characteristics and the thermal performance of steam flow in wide aspect ratio channels (W/H = 2) with different angled ribs on two opposite walls have been experimentally investigated in this paper. The averaged Nusselt number ratios and the friction factor ratios of steam and air in four ribbed channels were also measured under the same test conditions for comparison. The Reynolds number range is 6,000–70,000. The rib angles are 90°, 60°, 45°, and 30°, respectively. The rib height to hydraulic diameter ratio is 0.047. The pitch-to-rib height ratio is 10. The results show that the Nusselt number ratios of steam are 1.19–1.32 times greater than those of air over the range of Reynolds numbers studied. For wide aspect ratio channels using steam as the coolant, the 60° angled ribs has the best heat transfer performance and is recommended for cooling design.     

Conjugate heat transfer in the unbounded flow of a viscoelastic fluid past a sphere

This work addresses the conjugate heat transfer of a simplified PTT fluid flowing past an unbounded sphere in the Stokes regime (Re = 0.01). The problem is numerically solved with the finite-volume method assuming axisymmetry, absence of natural convection and constant physical properties. The sphere generates heat at a constant and uniform rate, and the analysis is conducted for a range of Deborah (0 ≤ De ≤ 100), Prandtl (10⁰ ≤ Pr ≤ 10⁵) and Brinkman (0 ≤ Br ≤ 100) numbers, in the presence or absence of thermal contact resistance at the solid–fluid interface and for different conductivity ratios (0.1 ≤ κ ≤ 10). The drag coefficient shows a monotonic decrease with De, whereas the normalized stresses on the sphere surface and in the wake first increase and then decrease with De. A negative wake was observed for the two solvent viscosity ratios tested (β = 0.1 and 0.5), being more intense for the more elastic fluid. In the absence of viscous dissipation, the average Nusselt number starts to decrease with De after an initial increase. Heat transfer enhancement relative to an equivalent Newtonian fluid was observed for the whole range of conditions tested. The dimensionless temperature of the sphere decreases and becomes more homogeneous when its thermal conductivity increases in relation to the conductivity of the fluid, although small changes are observed in the Nusselt number. The thermal contact resistance at the interface increases the average temperature of the sphere, without affecting significantly the shape of the temperature profiles inside the sphere. When viscous dissipation is considered, significant changes are observed in the heat transfer process as Br increases. Overall, a simplified PTT fluid can moderately enhance heat transfer compared to a Newtonian fluid, but increasing De does not necessarily improve heat exchange.     

Laminar thermally developing flow in rectangular channels and parallel plates: uniform heat flux

Numerical simulations were conducted for thermally developing laminar flow in rectangular channels with aspect ratios ranging from 1 to 100, and for parallel plates. The simulations were for laminar, thermally developing flow with H1 boundary conditions: uniform heat flux along the length of the channel and constant temperature around the perimeter. In the limit as the non-dimensional length, x* = x/(D _h RePr), goes to zero, the Nusselt number is dependent on x* to the negative exponent m. As the non-dimensional length goes to infinity the Nusselt number approaches fully developed values that are independent of x*. General correlations for the local and mean heat transfer coefficients are presented that use an asymptotic blending function to transition between these limiting cases. The discrepancy between the correlation and the numerical results is less than 2.5 % for all aspect ratios. The correlations presented are applicable to all aspect ratios and all non-dimensional lengths, and decrease the discrepancy relative to existing correlations.     

Flow and heat transfer in a pipe with a fin attached to inner wall

Enhancement of heat transfer to the fluid can be done by turbulence promoters such as attached fins to the pipe walls. In this study, the flow field and the heat transfer rates were numerically investigated in a pipe with an internally attached fin. Numerical simulations were conducted for four different types of fluids and for different fin heights and locations, and as the Reynolds number was varied, the effects of the fin on Nusselt number and friction factors were investigated. For all the Reynolds numbers considered in this study, the effect of fin location on the heat transfer rate and friction factor was negligible. As the fin height was increased, the mean Nusselt number and the friction factor also increased in the turbulent flow regimes. For low Prandtl number fluids (Pr = 0.011), the main heat transfer mode is conduction, and hence the mean Nusselt number slightly affected the flow rates.     

Influence of heating load on heat transfer characteristics in micro-pin-fin arrays

Experimental investigations were carried out to explore the convective heat transfer in micro pin-fins with different aspect ratios, and the influence of heating load on Nusselt numbers in micro pin-fins with liquid water as working fluid were investigated. The mechanism of convective heat transfer in micro pin-fins at different heating load were studied by 3-D numerical investigations, and the relationships of thermal physical properties change, the end wall effect and axial thermal conduction with Nu numbers in micro pin-fins were analysed. It was found that the thickness of boundary layer was decreased as much as 33.3 % attributed to the destructive effect of thermal physical properties change, and convective heat transfer in the micro pin-fin channel was more than 20 % enhanced by the flow disturbance caused by the increase of temperature difference. The discrepancy of Nu in micro pin-fin channel with different aspect ratios reached 34.59 %, and this discrepancy was reduced by the increase of heating load. The maximum value of impact factors of dynamic viscosity and thermal conductivity on the Nu in micro-pin-fins reached 25.02 and 7.68 %, respectively.     

A numerical and experimental study of natural convective heat transfer from an inclined isothermal square cylinder with an exposed top surface

Natural convective heat transfer from an isothermal inclined cylinder with a square cross-section which have an exposed top surface and is, in general, inclined at an angle to the vertical has been numerically and experimentally studied. The cylinder is mounted on a flat adiabatic base plate, the cylinder being normal to the base plate. The numerical solution has been obtained by solving the dimensionless governing equations subject to the boundary conditions using the commercial cfd solver, FLUENT. The flow has been assumed to be symmetrical about the vertical center-plane through the cylinder. Results have only been obtained for Prandtl number of 0.7. Values of inclination angle between 0° and 180° and a wide range of Rayleigh number and the dimensionless cylinder width, W = w/h, have been considered. The effects of Dimensionless widths, Rayleigh numbers, and inclination angles on the mean Nusselt number for the entire cylinder and for the mean Nusselt numbers for the various surfaces that make up the cylinder have been examined. Empirical equations for the heat transfer rates from the entire cylinder have been derived.     

Thermo-Bioconvection in a Square Porous Cavity Filled by Oxytactic Microorganisms

This paper studies the thermo-bioconvection in a square porous cavity filled by oxytactic microorganisms. The Darcy model with Boussinesq approximation has been used to solve the flow and heat and mass transfer in the porous region. The governing equations formulated in terms of the dimensionless stream function, temperature and concentration have been solved using the finite difference method. Comparison with results from the open literature of the mean Nusselt number for a square cavity filled with a regular porous medium is made. It is shown that the results are in very good agreement. The main objective was to investigate the influence of the traditional Rayleigh number Ra = 10, 100, bioconvection Rayleigh number Rb = 10, 100, Lewis number Le = 1, 10, and Péclet number Pe = 0.1, 1 on the fluid flow and heat and mass transfer. Comprehensive analysis of an effect of these key parameters on the Nusselt and Sherwood numbers at the vertical walls has been conducted.     

Heat transfer in turbulent pipe flow based on a new mixing length model

A new model for the heat transfer in turbulent pipe flow is presented based on a modified form of the mixing length theory developed by Cebeci [1] for boundary layer flow problems. The model predicts the velocity and temperature distributions and the Nusselt number for fluids with low, medium and high Prandtl numbers (Pr=.02 to 15) and fits the available experimental data very accurately for values of Reynolds number exceeding 10⁴. Expressions for the eddy conductivity and for the turbulent Prandtl number are presented and shown to be dependent upon the Reynolds number, the Prandtl number, and the distance from the tube wall.     

Natural convection in inclined rectangular enclosures with perfectly conducting fins attached on the heated wall

The natural convection heat transfer in inclined rectangular enclosures with perfectly conducting fins attached to the heated wall is numerically studied. The parameters governing this problem are the Rayleigh number (10²≤Ra≤2×10⁵), the aspect ratio of the enclosures (2.5≤A=H′/L′≤∞), the dimensionless lengths of the partitions (0≤B=?′/L′≤1), the aspect ratio of micro-cavities (A≤C=h′/L′≤0.33), the inclination angle (0≤φ≤60^°) and the Prandtl number (Pr=0.72). The results indicate that the heat transfer through the cover is considerably affected by the presence of the fins. At low Rayleigh numbers, the heat transfer regime is dominated by conduction. When B≈0.75 and C≈0.33, the heat transfer through the cold wall decreases considerably. This trend is enhanced when the enclosure is inclined. Useful engineering correlations are derived for practical applications.     

Heat transfer in magnetohydrodynamic laminar radial channel flow

Heat transfer in the steady axisymetrical laminar source flow of an incompressible electrically conducting fluid between two parallel disks in the presence of a transverse applied magnetic field is analyzed. The energy equation is solved numerically for the temperature distribution, where both Joulean and viscous heating are included. Both local and average Nusselt numbers for the case of constant wall temperature are evaluated. For fluids of moderate and high Prandtl numbers, Nusselt number is seen to be a strong function of both Hartmann number and a heat generation parameter together with a modified Peclet number. However, for fluids of small Prandtl number, Joulean heating and viscous dissipation can be neglected without appreciable error.