低温凝胶燃烧法合成Y2O3∶Er3+，Yb3+纳米晶上转换发光材料

分别以柠檬酸和甘氨酸为燃烧剂,采用低温凝胶燃烧法合成了Er³⁺、Yb³⁺共掺Y₂O₃纳米晶粉体。通过TG-DSC、XRD、SEM等分析手段对两种燃烧剂所对应的反应过程及纳米晶粉体的物理性能进行了分析,结果表明甘氨酸法具有更高的反应效率、更好的粉体分散性及粒径均匀性。在980 nm激光二极管(LD)激发下,对甘氨酸法所得样品的上转换发光性能分析表明,绿光和红光发射谱带分别来自于Er³⁺的⁴S_3/2/ ²H_11/2→ ⁴I_15/2和⁴F_9/2→ ⁴I_15/2跃迁。此外,对Er³⁺和Yb³⁺掺杂浓度、粉体煅烧温度对纳米晶样品上转换发光性能的影响进行了讨论。     

Yb3+/Tm3+共掺杂的钨酸镉纳米晶发光性能的研究

本文采用水热法制备了稀土离子Yb³⁺/Tm³⁺共掺杂的钨酸镉纳米晶。运用X-射线粉末衍射、场发射环境扫描电子显微镜和光谱分析对制备的样品的结构和发光性能进行了表征。根据XRD图谱可知, 钨酸镉为单斜晶系, 晶粒平均尺寸在28 nm左右。从ESEM图片可明显看出, 钨酸镉呈纳米棒结构, 直径在30 nm左右, 长径比在5~8之间。利用980 nm半导体激光器激发钨酸镉纳米晶得到样品的发射光谱, 存在一个较强的蓝光发射, 发光峰位于481 nm,对应于Tm³⁺的¹G₄→³H₆能级的跃迁, 分析了Tm³⁺/Yb³⁺离子共掺体系的发光机制。讨论了发光强度随稀土离子浓度的变化, 当Tm³⁺离子的掺杂浓度在2%, Yb³⁺/Tm³⁺物质的量浓度比为10:1时钨酸镉纳米晶的发光强度最强。根据泵浦功率与发光强度之间的关系, 可知处于481 nm的蓝光发射属于三光子过程, 由发光强度与掺杂浓度之间的双对数衰减曲线可知, 引起蓝光发射源于Tm³⁺的电偶极跃迁。     

水热合成LuF3∶Yb3+，Er3+微晶及其上转换发射与温度传感特性

通过在不同pH值下的简易水热法合成不同Yb³⁺离子（n_Yb³⁺/n_Lu³⁺=5%~15%）和Er³⁺离子（n_Er³⁺/n_Lu³⁺=1%~5%）掺杂浓度的LuF₃∶Yb³⁺,Er³⁺微晶荧光粉。发现pH值对正交相LuF₃∶Yb³⁺,Er³⁺的合成起着关键作用。在980 nm激发下,LuF₃∶Yb³⁺,Er³⁺荧光体呈现出以523 nm（²H_11/2→⁴I_15/2）和539 nm（⁴S_3/2→⁴I_15/2）为中心的强绿光上转换（UC）发射以及以660 nm（⁴F_9/2→⁴I_15/2）为中心弱红光上转换发射。通过使用X射线衍射（XRD）和光致发光（PL）分析测定了最强发射强度的Er³⁺和Yb³⁺的最佳掺杂浓度。浓度依赖性研究表明,达到最强的绿光上转换发光时最佳掺杂浓度为10% Yb³⁺,2% Er³⁺。通过改变泵浦功率来研究LuF₃∶Yb³⁺,Er³⁺荧光粉UC发光机制。通过980 nm二极管激光器在293~573 K的范围内研究了在523和539 nm处的2个绿光UC发射带的荧光强度比（FIR）的温度依赖性,发现在490 K得到最大灵敏度约为15.3×10^-4 K^-1。这表明LuF₃∶Yb³⁺,Er³⁺荧光体可应用于具有高灵敏度的光学温度传感器。     

一元醇热法制备SrHfO3：Ce超微球发光粒子

以Sr(NO₃)₂和HfOCl₂·8H₂O为原料,乙醇/水作溶剂,KOH为矿化剂,Ce(NO₃)₃·6H₂O作为激活剂,用一元醇热法制备了掺杂Ce³⁺的SrHfO₃超微球粒子。用XRD、SEM、荧光光度计分析了粒子合成过程的物相变化、形貌特征及激发和发射光谱。结果表明：在n_Sr：n_Hf=1：1,V_C2H5OH：V_H2O=4：1,水热合成温度140℃,反应时间4h,pH=13.5的条件下,获得SrHfO₃：Ce形貌为球微、分散均匀的粒子,粒径约900nm。当Ce³⁺掺杂浓度为0.7mol%时发光强度最大。     

Ho3+/Yb3+共掺ZnO-Al2O3-GeO2-SiO2玻璃陶瓷的制备和上转换发光性质

综合ZnO-Al₂O₃-SiO₂系和锗酸盐玻璃陶瓷的优点,采用熔融-晶化法首次制备了Ho³⁺/Yb³⁺共掺以ZnAl₂O₄为主晶相的ZnO-Al₂O₃-GeO₂-SiO₂系玻璃陶瓷。因[GeO₄]四面体和[SiO₄]四面体都是玻璃网络形成体,讨论了GeO₂取代SiO₂对玻璃陶瓷样品硬度及发光性能的影响,最终确定GeO₂的取代量为10.55%（w/w）时,玻璃陶瓷综合性能最佳。在980 nm泵浦光的激发下,发现强的绿色（546 nm）和弱的红色（650 nm）上转换发光,并研究了不同Ho³⁺/Yb³⁺掺杂比对样品上转换发光的影响,最终结果表明当Ho³⁺/Yb³⁺掺杂比为1：11（n/n）时样品荧光强度最强,在绿色上转换发光材料方面具有潜在的应用。     

Sb掺杂ZTO透明导电薄膜的结构和性能

采用溶胶凝胶法和旋涂法制备Sb掺杂钙钛矿结构ZTO（ZnSnO₃）透明电薄膜,并借助XRD、SEM、XPS、UV-Vis和Hall效应测试等手段研究了其结构和性能。比较了Sb离子单独置换ZnSnO₃晶体中的Zn²⁺或Sn⁴⁺,以及同时置换Zn²⁺和Sn⁴⁺等3种置换方式所得薄膜的结晶状态,分析了不同置换方式形成的薄膜中Sb离子实际占有的晶格位置,以及Sb⁵⁺与Sb³⁺的比例变化。探讨了不同置换方式晶体中氧空位（V_O^..）、锌间隙（Zn_i^..）和锡离子变价（Sn_Sn"）等结构缺陷相应的含量变化,并研究Sb离子掺杂浓度对薄膜晶体结构、结构缺陷和电阻率的影响。研究表明,3种置换方式的Sb掺杂ZTO薄膜均保持单一ZnSnO₃晶相,并且Sb离子均按设计的方案进入了相应的晶格位置,但不同置换方式的薄膜中,Sb⁵⁺与Sb³⁺的比例不同,并且会随Sb离子浓度增大而逐渐减小。研究证明Sb离子置换方式以及掺杂浓度均会显著影响薄膜中载流子的浓度和迁移率,从而影响其电性能。在所制备的薄膜中,Sb离子单独置换Zn²⁺且组成为Sb_0.15Zn_0.35Sn_0.5O_1.5的薄膜电阻率最低,为0.423 Ω·cm。此外,所有Sb掺杂ZTO薄膜在360~800 nm波长范围内透过率均在78%以上。     

Sr2Si5N8∶Eu2+荧光粉的制备与发光性能

以α-Si₃N₄,SrCO₃,Eu₂O₃为原料,采用碳热还原氮化法制备了Sr₂Si₅N₈∶Eu²⁺荧光粉。研究了材料的结构与光谱特性,分析了影响材料发光性能的工艺因素。结果表明,石墨粉含量和助熔剂的用量对Sr₂Si₅N₈相的形成和发光性能有重要影响。当n_C/n_Sr=1.5,助熔剂用量为4wt%时,合成样品的主晶相为正交晶系Sr₂Si₅N₈,在400~550 nm可见光激发下,可发射峰值波长位于609 nm荧光。激发带的位置与Eu²⁺离子浓度无关,为400~550 nm之间的宽带激发;但发射强度随Eu²⁺离子浓度的增加而增加,Eu²⁺离子浓度达到5mol%时发射强度达最大值,在Eu²⁺离子浓度为2mol%~5mol%之间,观察到发射峰的红移现象。     

Gd2O3:Yb3+,Nd3+,Tm3+/SiO2/Ag纳米复合材料的合成及上转换发光性质

通过多步骤的化学法合成了Gd₂O₃：Yb³⁺,Nd³⁺,Tm³⁺/SiO₂/Ag纳米复合材料。利用XRD,TEM,EDS,XPS,CLSM等方法对样品进行表征。实验结果表明,具有低声子能、稳定的化学性质的Gd₂O₃作为上转换发光的基质,当掺杂的敏化剂Nd³⁺离子浓度为1.0%（n/n）,激活剂离子Tm³⁺浓度为0.5%（n/n）时,上转换发光强度达到最大值。此外,表面吸附的Ag纳米颗粒,由于表面等离激元共振耦合作用,使得上转换发光蓝光波段的强度增强1.70倍。     

松香基季铵盐为模板剂有序超微孔二氧化硅的合成

以松香基季铵盐(脱氢枞基三甲基溴化铵,标记为DTAB)为模板剂、正硅酸乙酯为硅源、氨水为碱性介质成功合成出具有纳米片状形貌的六方有序超微孔二氧化硅材料。采用X射线衍射、N₂吸附-脱附、透射电镜、扫描电镜等手段对样品进行表征,结果表明,体系中模板剂添加量、硅源添加量、碱性介质添加量、晶化温度、搅拌时间对前驱体的有序度有着较大的影响。当物质的量之比为n_Sio2:n_DTAB:n_NH3·H2O:n_H2O=1.0:0.1:11.3:924.0,晶化温度为373K,搅拌时间为24h,所得样品有序度最高。经煅烧后样品具有较大的比表面积(1024 m₂·g^-1)和孔容(0.56 cm³·g^-1),以及狭窄的孔径分布(集中于1.80 nm)。     

绿色荧光粉Ca3Y2Si3O12:Tb3+,Ce3+的制备及发光特性

采用高温固相法合成了绿色荧光粉Ca₃Y₂Si₃O₁₂:Tb³⁺。XRD检测结果显示,荧光粉主晶相为Ca₃Y₂Si₃O₁₂,属单斜晶系。荧光光谱分析表明:Ca₃Y₂Si₃O₁₂:Tb³⁺硅酸盐荧光粉可以被370nm的近紫外光激发,发射绿光,主发射峰位于490nm(⁵D₄→⁷F₆),544nm(⁵D₄→⁷F₅),585nm(⁵D₄→⁷F₄)和621nm(⁵D₄→⁷F₃)。用544nm最强峰监测,得到主激发峰位于370nm的激发光谱,此光谱覆盖了300~450nm的波长范围。研究了煅烧条件、掺杂浓度及Ce³⁺共掺杂对荧光粉发光性能的影响:在1400℃下经二次煅烧6h得到的样品的发光性能最佳,Tb³⁺离子的最佳掺杂浓度为20mol%,Ce³⁺离子共掺杂能够提高荧光粉的发光强度,其最佳掺杂量为4mol%,说明存在Ce³⁺→Tb³⁺的能量传递。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.