Multielemental evaluation of garbage bags by EDXRF

Garbage bags have been broadly used for collecting household waste in Brazil and worldwide. Many of these bags are made from recycled polymers, and the presence of harmful elements is a matter of concern. In this study, an energy dispersive X-ray fluorescence (EDXRF) approach for direct analysis of garbage bags is proposed. The concentrations of K, Ca, Ti, Cr, Mn, Fe, Ni, Cu, Zn, Br, Rb, Sr and Pb were determined in 14 garbage bags of different brands purchased from local markets in Piracicaba, São Paulo State, Brazil. The EDXRF technique proved to be an effective technique for multielemental, environmentally friendly and direct garbage bag monitoring. For most samples, Ca and Ti presented at minor concentration ranges and K, Cr, Mn, Fe, Ni, Cu, Zn and Pb at minor and trace levels. The EDXRF limits of quantification were K: 220; Ca: 112; Ti: 42; Cr: 19; Mn: 13; Fe: 9.2; Ni: 5.7; Cu: 5.3; Zn: 5.2; Br: 12; Rb: 20; Sr: 28 and Pb:17 μg g^–1. The samples had variable thicknesses, with a superficial density variation of 1.5 to 23% among the triplicates. The trueness of the method was checked by analysing the National Institute of Standards and Technology standard reference material SRM2783.     

ICP–AES法测定铬镍不锈钢中锰、铬、镍、硅、磷、铜、钼的含量

建立电感耦合等离子体原子发射光谱(ICP–AES)法测定铬镍不锈钢中锰、铬、镍、硅、磷、铜、钼7种元素含量的方法。试样用盐酸与硝酸混合酸溶液溶解,采用溶解国家标准样品的方法制备校准曲线溶液,确定了元素最佳分析谱线。各元素的含量在其测试范围内与原子发射强度呈良好的线性关系,线性相关系数不小于0.999,7种元素的检出限在0.000 3%~0.003 0%之间。该方法应用于铬镍不锈钢标准样品的测定,测定值与认定值相符,测定值的相对标准偏差在0.12%~1.15%之间(n=8)。应用于铬镍不锈钢样品测定时,加标回收率在90%~110%之间。该方法操作简便、迅速,可满足日常铬镍不锈钢中多元素含量的检测需要。     

Calibration graphs for steels by IR laser ablation inductively coupled plasma atomic emission spectrometry

Infrared laser ablation (IRLA) was studied as a sample-introduction technique for the analysis of steels by inductively coupled plasma atomic emission spectrometry (ICP–AES). A comparison of two IRLA–ICP–AES systems based on Q-switched nanosecond Nd?:?YAG lasers was performed. The beam of the Lina-Spark atomizer (LSA Sarl, Cully, Switzerland) based on the Surelite I-20 laser (Continuum, USA) was moved along a circle. A Perkin–Elmer Optima 3000 DV ICP system was used both with lateral and axial viewing modes. A laboratory-made ablation system based on the Brilliant laser (Quantel) was coupled to a Jobin-Yvon 170 Ultrace ICP (lateral viewing, polychromator part employed). A sample was rotated along a circle during ablation. Linearity of calibration plots was verified at least up to 19% Cr and 12% Ni without internal standardization for both LA–ICP–AES systems. Other elements examined were Mo up to 3%, Mn up 1.5%, Si up to 1.7%, and Cu up to 0.15%. The reproducibility was in the range 5–1 %RSD for a mass percentage 0.5–20% of steel constituents. The relative uncertainty of the centroids of the calibration lines was in the range from ± 4% to ± 12% for Cr, Ni, Mn, Mo, and Si, and from ± 8% to ± 19% for Cu. The lowest determinable quantities were calculated for calibration dependencies. Performances of both the IR-LA–ICP–AES were comparable.     

Quantitative determination of wear metals in engine oils using laser-induced breakdown spectroscopy: A comparison between liquid jets and static liquids

A comparison of laser-induced breakdown spectroscopy (LIBS) sensitivity in laminar liquid jets and at the surface of a static liquid has been performed. Limits of detection (LODs) have been estimated for Na, Mg, Al, Ca, Ti, V, Cr, Mn, Ni, Fe, Cu, Zn, Mo, Ag, Cd, and Ba under similar conditions using both experimental arrangements. LODs in liquid jets are found to be four times lower on average compared to measurements at static surfaces. Data acquisition rates in jet experiments are also generally higher than for static liquids due to reduced problems with splashing effects.The use of LIBS in jets has also been investigated for quantitative analysis of used lubricants. A number of contaminants have been measured in a set of used engine oils and the results compared to analysis via ICP-AES, where a good correlation is obtained.     

Determination of impurities in high-purity niobium(V) oxide by high-resolution continuum source graphite furnace atomic absorption spectrometry after sorption preconcentration

Method of sorption–atomic-absorption determination of Co, Cr, Cu, Fe, Mn, and Ni in samples of high-purity Nb₂O₅ with heterochain S,N-containing sorbents was developed. The method is based on the sorption preconcentration of trace impurities followed by their determination by high-resolution continuum source graphite furnace atomic absorption spectrometry (HR CS GFAAS). Selectivity of three original inhouse synthesized S,N-containing heterochain sorbents was studied. The recoveries of Co, Cr, Cu, Fe, Mn, and Ni using heterochain sorbents OKS, MTH, and GLSH were 100, 80, and 76%, correspondingly. Sorbent “OKS”, which provided the quantitative recovery of trace impurities, was chosen for further research. The sorption conditions for chloride solutions of different acidities (0.1–3 M HCl) were studied and optimized. Using the conditions established for the sorption and HR CS GFAAS analysis, trace Co, Cr, Cu, Fe, Mn, and Ni were determined in high purity Nb₂O₅ with a relative error less than 5%. The trueness control of the obtained results is confirmed by the “added–found” method. The developed method allows us to determine concentrations of analytes: 0.02–0.20 ppm Co, 2.0–3.3 ppm Cr, 0.2–1.5 ppm Cu, 6.0–21.0 ppm Fe, 0.6–0.8 ppm Mn, and 2.8–3.5 ppm Ni. The proposed methodology can be successfully extended to the determination of various trace elements in other high-purity inorganic materials.     

Parametric study of a fiber-optic laser-induced breakdown spectroscopy probe for analysis of aluminum alloys

In the present work we demonstrate a fiber-optic laser-induced breakdown spectroscopy (FO LIBS) system for delivering laser energy to a sample surface to produce a spark as well as to collect the resulting radiation from the laser-induced spark. In order to improve the signal/background (S/B) ratio, various experimental parameters, such as laser energy, gate delay and width, detector gain, lenses of different focal lengths and sample surface, were tested. In order to provide high reliability and repeatability in the analysis, we also measured plasma parameters, such as electron density and plasma temperature, and determined their influence on the measurement results. The performance of FO LIBS was also compared with that of a LIBS system that does not use a fiber to transmit the laser beam. LIBS spectra with a good S/B were recorded at 2-μs gate delay and width. LIBS spectra of six different Al alloy samples were recorded to obtain calibration data. We were able to obtain linear calibration data for numerous elements (Cr, Zn, Fe, Ni, Mn, Mg and Cu). A linear calibration curve for LIBS intensity ratio vs. concentration ratio reduces the effect of physical variables (i.e. shot-to-shot power fluctuation, sample-to-surface distance, and physical properties of the samples). Our results reveal that this system may be useful in designing a high-temperature LIBS probe for measuring the elemental composition of Al melt.     

Molybdenum(VI) Oxide-Modified Silica Gel as a Novel Sorbent for the Simultaneous Solid-Phase Extraction of Eight Metals with Determination by Flame Atomic Absorption Spectrometry

A silica-based inorganic sorbent was synthesized by the thermal decomposition of ammonium heptamolybdate on silica and applied for the preconcentration and simultaneous determination of Cd, Co, Cr, Cu, Fe, Mn, Ni, and Pb in river water samples using a column system with flame atomic absorption spectrometry. Attenuated total reflection-Fourier transformation infrared spectroscopy, scanning electron microscopy, and electron dispersive spectroscopy were used for sorbent characterization. The effects of pH, sample volume, eluent type, eluent concentration, eluent volume, sample flow rate, and matrix ions (Al, Bi, Ca, Mg, and Zn) on the recovery of the metals in model solutions were investigated. The adsorption capacities (µmol g^?1) of SiO₂-MoO₃ were 88.96 (Cd), 169.69 (Co), 153.85 (Cr), 188.88 (Cu), 179.05 (Fe), 163.81 (Mn), 136.31 (Ni), and 38.61 (Pb). The detection limits of the method were 9.09, 10.82, 10.77, 49.57, 31.64, 6.40, 8.86, 19.15?µg L^?1 for Cd, Co, Cr, Cu, Fe, Mn, Ni, and Pb, respectively, with a preconcentration factor of 25. The developed method was used for the determination of the target metals in real samples and the recoveries for spiked samples were found to be from 91.2% to 102.9%.     

Fast and sensitive trace metal analysis in aqueous solutions by laser-induced breakdown spectroscopy using wood slice substrates

To perform fast and sensitive trace metal analysis in aqueous solutions by laser-induced breakdown spectroscopy (LIBS) based on only one single-pulse laser system, a wood slice has been used as a liquid absorber to transform liquid sample analysis to solid sample analysis using LIBS. High detection sensitivity and good reproducibility can be achieved with this approach. Calibration curves for five metal elements, Cr, Mn, Cu, Cd, and Pb under trace concentrations, have been obtained, and the limits of their detection were determined to be in the range of 0.029–0.59 mg L^− 1, 2–3 orders better than those obtained by directly analyzing liquid samples where the laser was focused on a liquid surface. The wood slice was very easy to handle and thus, the whole analysis process took only 4–5 min for each sample. This approach provides a more practical approach for fast and sensitive metal element analysis in aqueous solutions using LIBS, which is especially useful for monitoring toxic heavy metals in water.     

Approach combining on-line metal exchange and tangential-flow ultrafiltration for in-situ characterization of metal species in humic hydrocolloids

This paper deals with the development and optimization of an analytical procedure using ultrafiltration and a flow-injection system, and its application in in-situ experiments to characterize the lability and availability of metal species in humic-rich hydrocolloids. The on-line system consists of a tangential flow ultrafiltration device equipped with a 3-kDa filtration membrane. The concentration of free ions in the filtrate was determined by atomic-absorption spectrometry, assuming that metals not complexed by aquatic humic substances (AHS) were separated from the complexed species (M–AHS) retained by the membrane. For optimization, exchange experiments using Cu(II) solutions and AHS solutions doped with the metal ions Ni(II), Mn(II), Fe(III), Cd(II), and Zn(II) were carried out to characterize the stability of the metal–AHS complexes. The new procedure was then applied in-situ at a tributary of the Ribeira do Iguape river (Iguape, São Paulo State, Brazil) and evaluated using the ions Fe(III) and Mn(II), which are considered to be essential constituents of aquatic systems. From the exchange between metal–natural organic matter (M–NOM) and the Cu(II) ions it was concluded that Cu(II) concentrations >485 μg L^?1 were necessary to obtain maximum exchange of the complexes Mn–NOM and Fe–NOM, corresponding to 100% Mn and 8% Fe. Moreover, the new analytical procedure is simple and opens up new perspectives for understanding the complexation, transport, stability, and lability of metal species in humic-rich aquatic environments.     

Direct solid atomic emission spectrometric analysis of metal samples by an argon microwave plasma torch coupled to spark ablation

Spark ablation has been combined to microwave plasma torch atomic emission spectrometry for the direct analysis of compact metallic samples. The material is ablated by a medium voltage spark (450 V, 370 Hz) in a point-to-plane configuration and swept into a 100-W, 2.45-GHz argon microwave discharge. The microwave plasma is observed end-on and the radiation analysed with a polychromator. The detection limits for Fe, Ni, Pb and Sn in brass, Cr, Cu, Ni, Mn, Mo, Si and V in steel and Cu, Fe, Mg, Mn, Si and Zn in aluminium with the microwave plasma torch in the case of measurements with a polychromator are in the μg/g range and by a factor of up to 20 higher than those obtained with spark ablation coupled to inductively coupled plasma atomic emission spectrometry using a high resolution sequential spectrometer. The stability of the emission signal depends on the element studied and relative standard deviations usually are between 0.5 and 3.5%. In the case of low-alloy steels, the linearity and the precision of the calibration could be improved by internal standardisation. Several elements (Cr, Cu, Ni, Si and V) could be determined in a steel sample (BAS SS 410/1) with high accuracy and precision.     

Application of vacuum ultraviolet laser-induced breakdown spectrometry for steel analysis — comparison with spark-optical emission spectrometry figures of merit

Laser induced breakdown spectrometry (LIBS) was evaluated for trace analysis in steel in comparison to spark discharge optical emission spectrometry (spark-OES), including low C, N and S (<100 ppm) concentrations. The development of an industrial prototype is described, with the ability to be able to use either a spark or a laser source on the same optical mounting to directly compare the performances of both sources. Similar sensitivities between LIBS and spark-OES could be obtained for low alloying elements (Mn, Cr, Ni, Mo, etc., in the range of 0–1200 ppm) as well as for traces of C, N, S, P between 2 and 100 ppm. Limits of detection as low as 5 ppm were measured in a reproducible way for C, P, and S, whereas lower N signal stabilities result in 20 ppm LOD. Compared to a spark source used on the same optical mounting, it should be possible to improve these figures by a factor of 3. The results presented in this work lead us to believe that LIBS should rapidly develop as a steel control tool, and the instrumentation built up will be suitable for on-site process control applications.     

Application of LIBS to the in-line process control of liquid high-alloy steel under pressure

A process optimization and control system called VAI-CON Chem has been developed that uses laser-induced breakdown spectroscopy (LIBS) to quasi-continuously chemically analyze liquid high-alloy steel under pressure. The beam from a Nd:YAG laser, located on safe ground and operating at its fundamental wavelength, is guided by a mirror system to a process tuyere below bath level. Passing through the ∼1.5 m long tuyere, the beam is then focused onto the steel bath. Light emitted from the induced plasma passes back through the tuyere, which is coupled to a fiber optic cable that carries the information over a distance of approximately 10 m back to an Echelle spectrometer located beside the laser. Calibrations were performed using the complete system, located in a laboratory, during system testing. An induction furnace was used to simulate the AOD converter, wherein the samples were molten and superheated to a temperature of ∼1600 °C and kept at a pressure of ∼1.7 bar under an argon atmosphere. Twelve different high alloyed reference samples taken from normal AOD production with Fe concentrations of >48 wt.% and non-Fe element concentrations of up to 25 wt.% were available for calibration. The mean residual deviations (defined as the square root of the variance of the concentration ratios determined by LIBS and the reference element concentration ratios) obtained were close to those reported for other comparable high-alloy samples that were investigated at room temperature under normal atmospheric pressure.     

Control of the composition of lanthanum gallium silicate by laser ablation inductively coupled plasma mass spectrometry

The possibilities of determining the impurities and basic components of lanthanum gallium silicate using laser ablation in combination with inductively coupled plasma mass spectrometry (LA-ICP-MS) were shown. A procedure for the determination of 54 impurity elements with the limits of determination from n × 10^?5 wt % for Mg, Ti, V, Cr, Mn, Ni, Cu, and Zn to 2 × 10^?7 wt % for U and also a procedure for the determination of a ratio between basic components were developed. It was found that the concentration ratios between gallium and lanthanum and silicon and lanthanum in the crystals of lanthanum gallium silicate remained constant upon consecutive melting operations with the addition of a charge mixture to the crucible.     

A rapid separation method for radioscandium from proton-irradiated transition metals

The selectivity of trioctylphosphineoxide /TOPO/ with respect to rare earths and sc was used to develop a single step separation method for^43–48Sc from transition metals irradiated with high energy protons /660 MeV/. The target material serves as a salting-out agent in the described extraction-separation technique. Rapid and quantitative recovery of scandium is achieved using extraction chromatography. Radiochemically pure carrier-free Sc was separated from the following irradiated metals: Cr, Mn, Ni, Cu and Zn.     

不锈钢的 X射线荧光光谱分析

用高性能飞利浦PW2400X射线荧光光谱仪,测定不锈钢中Al、Si、P、S、Ti、Cr、Mn、Co、Ni、Cu、As、Mo、Sn、W、Fe15个元素。给出了各元素的干扰校正系数和基体效应校正系数。方法准确、灵敏、稳定性好、速度快。     

Nanometer-sized zirconium dioxide microcolumn separation/preconcentration of trace metals and their determination by ICP-OES in environmental and biological samples

A new method is proposed using a microcolumn (20 mm × 2.0 mm) packed with nanometer-sized zirconia as solid-phase extractor for the separation/preconcentration of Mn, Cu, Cr, Zn, Ni and Co prior to their determination by inductively coupled plasma optical emission spectrometer (ICP-OES) in environmental samples. The factors affecting the separation and preconcentration of analytes such as pH, sample flow rate and volume, eluent concentration and volume were determined, interfering ions were studied, and the optimal experimental conditions were established. The adsorption capacity of nanometer-sized ZrO₂ for Mn, Cu, Cr, Zn, Ni and Co was found to be 1.3, 1.3, 1.7, 2.0, 3.9 and 1.5 mg g⁻¹, respectively. The detection limits of the method were 12, 58, 24, 2, 7 and 36 ng L⁻¹, respectively, with a preconcentration factor of 25. The precision of this method was 1.7% (Mn), 2.9% (Cu), 5.9% (Mn), 3.8% (Mn), 6.2% (Mn) and 4.3% (Mn) with 9 determinations of 10 ng mL⁻¹ of target analytes, respectively. The method was successfully applied to the determination of trace metals in lake water, dried fish samples, certified reference materials of human hair and milk, and provided satisfactory results.     

Distribution of Minor and Trace Metals in Carezza Lake (ANTARCTICA) Ecosystem

Abstract

This paper reports the distribution of a series of metals in natural samples collected at Carezza Lake in Antarctica, during the Italian Expedition in the austral summer 1989/90. The considered elements are: water, sediments and soil sampled from the surroundings of the lake and algae. The determination of the total concentration of the following metals was performed: Al, As, Ca, Cd, Co, Cr, Cu, Fe, Mg, Mn, Na, Ni, Pb, Zn. In addition, for sediment and soil samples, a speciation study was performed for some metals, namely Cd, Co, Cr, Cu, Fe, Mn, Ni, Zn, using the Tessier procedure.     

Cadmium and other metals in Swedish wheat and rye flours: longitudinal study, 1983-1997.

Wheat flour (sifted), wheat bran, and rye flour were sampled annually in several different areas in Sweden for 15 consecutive years (1983-1997) for a total of 105, 90, and 30 samples, respectively. These samples were analyzed for their content of Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, and Zn by atomic absorption spectrophotometry with background correction after dry ashing at 450 degrees C. As part of the quality control procedures, an in-house reference material was analyzed in parallel to the samples to ensure reliability of the results. In addition, a certified reference material was analyzed to monitor accuracy of the results. The Cd level in wheat and rye flours (mean 0.029 and 0.017 mg/kg dry wt, respectively) correlated significantly with time (p < 0.05) in 2 phases, tending to increase during the first half of the period and decrease during the latter half. In wheat bran, Cd (mean 0.15 mg/kg) levels did not correlate significantly with time. In wheat flour, Cu, Mn, and Zn (means 1.7, 6.2, and 7.6 mg/kg, respectively) showed a significant linear increase (p < 0.05) in concentration over time. In rye flour, the levels of Cu, Fe, Mn, and Zn (means 3.8, 36, 30, and 28 mg/kg, respectively) all decreased significantly (p < 0.05) over time. Similarly, in wheat bran Cu (mean 14 mg/kg) increased and Pb (mean 0.027 mg/kg) decreased significantly (p < 0.05) over time, whereas Ni and Zn showed a significant curved correlation with time and peaked at about the middle of the measurement period.     

Co-doping a metal (Cr,Mn, Fe,Co, Ni,Cu, and Zn) on Mn/ZSM-5 catalyst and its effect on the catalytic reduction of nitrogen oxides with ammonia

Selective catalytic reduction (SCR) of NO_x by NH₃ over a series of Mn–M/Z catalysts (M = Cr, Mn, Fe, Co, Ni, Cu, Zn, and Z = the ZSM-5 Zeolite) synthesized by wet impregnation method was investigated. Mn–Fe/Z, Mn–Co/Z, and Mn–Cu/Z catalysts exhibited approximately 100 % NO_x conversion over a wide temperature range (200–360 °C) in a defined atmospheric condition, which was noticeably greater than that of Mn–Cr/Z (340–360 °C). Furthermore, the effect of addition of second metal oxide species to the initial Mn/Z catalyst on the structure of catalysts was studied by several characterization techniques. BET measurements revealed high surface area and pore volume of the Mn–Cu/Z catalyst. In addition, the XRD and UV–Vis DR results showed that addition of co-doped metal oxide species improved the dispersion of metal ions and inhibited crystallization of metal oxides. UV–Vis studies also were in good accordance with DTA/TG results confirming the formation of cobalt oxide and copper oxide clusters in Mn–Co/Z and Mn–Cu/Z catalysts, respectively. The FTIR spectra of pyridine adsorption, in addition, suggested the Mn–Cu/Z catalyst contained the most Lewis acid sites leading to more NO_x adsorption capacity.