首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
This paper is concerned with the mechanical behaviour of 316 austenitic stainless steel under multiaxial loadings and particular attention is paid to ratchetting under tension–torsion non-proportional loadings. First, a series of uniaxial tests and biaxial tests has been carried out in order to calibrate five different cyclic plasticity models based on an isotropic hardening rule and a non-linear kinematic hardening rule. It is shown that this class of models gives quite good agreement between the experimental and numerical results. Second, another series of ratchetting tests has been carried out under tension–torsion loadings in order to test the prediction capacities of the previous models. It is shown that whereas the models have been calibrated with similar loading paths, four of the five selected models give poor predictions.  相似文献   

2.
3.
Elastic–plastic behavior of two types of steel sheets for press-forming (an aluminum-killed mild steel and a dual-phase high strength steel of 590 MPa ultimate tensile strength) under in-plane cyclic tension–compression at large strain (up to 25% strain for mild steel and 13% for high strength steel) have been investigated. From the experiments, it was found that the cyclic hardening is strongly influenced by cyclic strain range and mean strain. Transient softening and workhardening stagnation due to the Bauschinger effect, as well as the decrease in Young's moduli with increasing prestrain, were also observed during stress reversals. Some important points in constitutive modeling for such large-strain cyclic elasto-plasticity are discussed by comparing the stress–strain responses calculated by typical constitutive models of mixed isotropic–kinematic hardening with the corresponding experimental observations.  相似文献   

4.
In this work, we develop a physically-based crystal plasticity model for the prediction of cyclic tension–compression deformation of multi-phase materials, specifically dual-phase (DP) steels. The model is elasto–plastic in nature and integrates a hardening law based on statistically stored dislocation density, localized hardening due to geometrically necessary dislocations (GNDs), slip-system-level kinematic backstresses, and annihilation of dislocations. The model further features a two level homogenization scheme where the first level is the overall response of a two-phase polycrystalline aggregate and the second level is the homogenized response of the martensite polycrystalline regions. The model is applied to simulate a cyclic tension–compression–tension deformation behavior of DP590 steel sheets. From experiments, we observe that the material exhibits a typical decreasing hardening rate during forward loading, followed by a linear and then a non-linear unloading upon the load reversal, the Bauschinger effect, and changes in hardening rate during strain reversals. To predict these effects, we identify the model parameters using a portion of the measured data and validate and verify them using the remaining data. The developed model is capable of predicting all the particular features of the cyclic deformation of DP590 steel, with great accuracy. From the predictions, we infer and discuss the effects of GNDs, the backstresses, dislocation annihilation, and the two-level homogenization scheme on capturing the cyclic deformation behavior of the material.  相似文献   

5.
A recently-developed crystal-mechanics-based constitutive model for polycrystalline shape-memory alloys [J. Mech. Phys. Solids 49 (2001) 909] is shown to quantitatively predict the superelastic response of an initially-textured Ti–Ni alloy in (i) a proportional-loading, combined tension–torsion experiment, as well as (ii) a path-change, tension–torsion experiment.  相似文献   

6.
This report describes investigations of grain boundary groove effects on mode II dominated interface fracture. The study focused on a specific interface between stainless steel and an epoxy adhesive. First, a finite element model was developed to simulate residual stresses and crack propagation. Second, the simulation results were compared with the experimental results from a previous study (Kanerva et al., 2013. Eng. Fract. Mech. 99, 147-158). Additional measurements were performed using atomic force microscopy. Based on the simulation, a 100-fold toughening effect due to the grain boundaries was determined. Implementation of flaws, in the form of interfacial voids, decreased the toughening effect by 35% and increased the mode II dominance significantly. The work underlines the practical importance of complete wetting by the adhesive and its necessary adherence to the grain boundary groove walls.  相似文献   

7.
The bifurcation and chaos of a cable–beam coupled system under simultaneous internal and external resonances are investigated. The combined effects of the nonlinear term due to the cable’s geometric and coupled behavior between the modes of the beam and the cable are considered. The nonlinear partial-differential equations are derived by the Hamiltonian principle. The Galerkin method is applied to truncate the governing equation into a set of ordinary differential equations. The bifurcation diagrams in three separate loading cases, namely, excitation acting on the cable, on the beam and simultaneously on the beam and cable, are analyzed with changing forcing amplitude. Based on careful numerical simulations, bifurcations and possible chaotic motions are represented to reveal the combined effects of nonlinearities on the dynamics of the beam and the cable when they act as an overall structure.  相似文献   

8.
The main objective of this paper is to investigate the mechanical behaviour (strength and stiffness) of carbon nanotubes (CNTs) under combinations of bending and twisting. In order to achieve this goal, molecular dynamics (MD) simulations of bended and twisted CNTs are performed. The LAMMPS code is used, the AIREBO potential is considered for CC bonds, the temperature is kept at 300 K and incremental bending and twisting rotations are imposed to the CNT. Two types of CNTs are analyzed, including zig-zag (8,0) and armchair (5,5) CNTs with similar radius and length. The CNTs are also analyzed for pure bending and pure twisting. The main results are shown in the form of diagrams of energy and moment against imposed rotations. Some relevant conclusions are drawn concerning the influence of loading (bending and twisting) on the stiffness, strength and failure of CNTs: namely, it is concluded that armchair CNTs possess higher strength and fracture toughness under twisting–bending loading than zigzag CNTs; additionally, it is found that both CNTs (armchair and zigzag) still support moderate-to-high bending levels without failure after being extremely twisted and torsionally buckled, even for twisting angles four times those corresponding to torsional buckling; finally, the results prove that CNTs, mostly armchair ones, exhibit very high twisting–bending stiffness and strength and can be used with confidence as torsional spring elements in nanoelectromechanical systems (NEMS).  相似文献   

9.
The paper presents analytical solutions for the equal-rate mechanochemical wear of an ideal elastic–plastic thick-walled cylindrical tube subjected to any combination of internal and external pressure. The rates of corrosion at the inner and outer surfaces are supposed to be proportional to the equivalent tensile stress at the surface involved when it exceeds a given threshold. Furthermore, the corrosion rate can decay exponentially with time. The obtained solutions allow to assess the time of the initial yielding at the bore of the tube and the time of fully plastic yielding. Calculations showed that the time of plastic-zone propagation throughout the tube wall can be much greater than the length of the pure elastic stage. The proposed analytical solutions are to be used for design purposes and as benchmark solutions for numerical analysis.  相似文献   

10.
The paper examines the plastic bending of steel tubes exhibiting Lüders bands through a combination of experiments and analyses. In pure bending experiments on tubes with diameter-to-thickness ratio of 18.8 tested under end-rotation control, following the elastic regime the moment initially traced a somewhat ragged plateau. At the beginning of the plateau Lüders bands appeared on the tension and compression sides of the cross section and simultaneously the curvature localized in one or two short zones while the rest of the tube maintained a much lower curvature. As the rotation of the ends was increased, one of the higher curvature zones spread at a nearly steady rate, affecting an increasingly larger part of the tube. When the whole tube was deformed to the higher curvature, the moment started to gradually increase while the tube deformed uniformly. A moment maximum was eventually attained and the structure failed by localized diffuse ovalization without any apparent effect from the initial Lüders bands-induced propagating instability. The problem was analyzed using 3D finite elements with a fine mesh. The material was modeled as an elastic–plastic solid with an up–down–up response over the extent of the Lüders strain, followed by hardening. The calculated response reproduced all major structural events observed experimentally including the initiation of the Lüders deformation, the moment plateau that followed, its extent, and the curvature localization and propagation associated with it. As in the experiments, once the high curvature extended over the whole tube length, the response of the tube became stable and the curvature uniform. With further bending the increasing ovalization induced a limit moment at a very high curvature.  相似文献   

11.
Based on the cells’ collapse mechanisms of the hexagonal honeycombs revealed from the numerical simulations under the low-velocity impact, an analytical model is established to deduce the crushing strength of the honeycomb and the stress at the supporting end both as functions of impact velocity, cell size, cell-wall angle, and the mechanical properties of the base material. The results show that the honeycomb’s crushing strength increases with the impact velocity, while the supporting stress decreases with the increase of the impact velocity. Combining with the dynamic predictions under the high-velocity impact in our previous work (Hu and Yu, 2010), the crushing strength of the honeycombs can be analytically predicted over wide range of crushing velocities. The analytical expression of the critical velocity is also obtained, which offers the boundary for the application of the functions of the honeycomb’s crushing strength under the low-velocity and the high-velocity impacts. All of the analytical predictions are in good agreement with the numerical simulation results.  相似文献   

12.
In this paper, an analytical solution is developed to determine deformations and stresses in circular disks made of functionally graded materials subjected to internal and/or external pressure. Taking mechanical properties of the materials of circular disks to be linear variations, the governing equation is derived from basic equations of axisymmetric, plane stress problems in elasticity. By transforming the governing equation into a hypergeometric equation, an accurate analytical solution of deformations and stresses in circular disks is obtained. The comparison with the numerical solution indicates that both approaches give very agreeable results, indicating correctness of the proposed analytical solution. The obtained analytical solution is employed to determine the radial displacement and stresses in circular disks subjected to external pressure, internal pressure, and internal and external pressure, respectively. How the radius ratio of circular disks affects deformations and stresses is also investigated.  相似文献   

13.
The two-phase flow of a hydrophobic ionic liquid and water was studied in capillaries made of three different materials (two types of Teflon, FEP and Tefzel, and glass) with sizes between 200 μm and 270 μm. The ionic liquid was 1-butyl-3-methylimidazolium bis{(trifluoromethyl)sulfonyl}amide, with density and viscosity of 1420 kg m−3 and 0.041 kg m−1 s−1, respectively. Flow patterns and pressure drop were measured for two inlet configurations (T- and Y-junction), for total flow rates of 0.065–214.9 cm3 h−1 and ionic liquid volume fractions from 0.05 to 0.8. The continuous phase in the glass capillary depended on the fluid that initially filled the channel. When water was introduced first, it became the continuous phase with the ionic liquid forming plugs or a mixture of plugs and drops within it. In the Teflon microchannels, the order that fluids were introduced did not affect the results and the ionic liquid was always the continuous phase. The main patterns observed were annular, plug, and drop flow. Pressure drop in the Teflon microchannels at a constant ionic liquid flow rate, was found to increase as the ionic liquid volume fraction decreased, and was always higher than the single phase ionic liquid value at the same flow rate as in the two-phase mixture. However, in the glass microchannel during plug flow with water as the continuous phase, pressure drop for a constant ionic liquid flow rate was always lower than the single phase ionic liquid value. A modified plug flow pressure drop model using a correlation for film thickness derived for the current fluids pair showed very good agreement with the experimental data.  相似文献   

14.
The present study has attempted to investigate phase inversion and frictional pressure gradients during simultaneous vertical flow of oil and water two-phase through upward and downward pipes. The liquids selected were white oil (44 mPa s viscosity and 860 kg/m3 density) and water. The measurements were made for phase velocities varying from 0 to 1.24 m/s for water and from 0 to 1.87 m/s for oil, respectively. Experiments were carried either by keeping the mixture velocity constant and increasing the dispersed phase fraction or by keeping the continuous phase superficial velocity constant and increasing the dispersed phase superficial velocity. From the experimental results, it is shown that the frictional pressure gradient reaches to its lower value at the phase inversion point in this work. The points of phase inversion are always close to an input oil fraction of 0.8 for upward flow and of 0.75 for downward flow, respectively. A few models published in the literature are used to predict the phase inversion point and to compare the results with available experimental data. Suitable methods are suggested to predict the critical oil holdup at phase inversion based on the different viscosity ratio ranges. Furthermore, the frictional pressure gradient is analyzed with several suitable theoretical models according to the existing flow patterns. The analysis reveals that both the theoretical curves and the experimental data exhibit the same trend and the overall agreement of predicted values with experimental data is good, especially for a high oil fraction.  相似文献   

15.
With the aid of the micro-mechanical model of knitted fabric proposed in Part 1 we analyze the buckling of a knitted fabric sheet when it is subjected to a tension along the wale direction. The large deformation of the fabric sheet in the critical configuration is considered and, to avoid possible deviation due to the approximation of the theory of thin plate, the three-dimensional theory of instability is used. The fabric sheet is considered as a three-dimensional body and all boundary conditions are satisfied. It is shown that the buckling of the fabric sheet is possible, two buckling modes and the corresponding buckling conditions are obtained, but only the flexural mode is physically possible as observed in experiments.The project supported by the National Natural Science Foundation of China (10272079)  相似文献   

16.
Micro-structured optical fibres (i.e. fibres that contain holes) have assumed a high profile in recent years and given rise to many novel optical devices. The problem of manufacturing such fibres by heating and then drawing a preform is considered for the case of annular capillaries. A fluid mechanics model suggested in the literature that uses asymptotic analysis based on the small aspect ratio of capillaries has been compared with the full 3D set of the N.–St. equations, for modelling the fabrication of capillaries. The final asymptotic equations, analysed in some asymptotic limits, are solved numerically and then compared with the N.–St. solutions, obtained with a commercial finite elements solver. These asymptotic limits give valuable practical information about the control parameters that influence the drawing process, taking into account the effects of surface tension and inner pressure, since those are of essential importance during drawing. It is shown that the asymptotic method delivers reliable results as long as the inner pressure does not exceed too high values.  相似文献   

17.
To promote a better understanding of liquid–liquid two-phase flow behavior, particularly under high pressure, flow patterns of n-hexadecane–CO2 liquid–liquid two-phase upward flow in vertical stainless steel pipes were experimentally investigated. Observations were made in two 0.0015 m I.D. pipes of different lengths (0.068 m and 0.5 m) under high pressure varying from 10.3 to 29.6 MPa using a high pressure visualization system. The total flow rate was fixed at 2.0 × 10−6 m3/min, while the flow rate ratio (φ) varied from 0.05 to 19. Bubbly flow, plug flow, slug flow, annular flow, and near-one-phase flow regions were found in both pipes, while stratified flow was observed only in the 0.068 m pipe. Flow pattern maps were constructed in the flow rate ratio versus pressure graph, which demonstrates significant impacts of flow rate ratio, pipe length, and pressure on flow patterns. These impacts are discussed in detail. To the authors’ best knowledge, this work is the first attempt to observe complex liquid–liquid two-phase flow behavior with flow pattern transitions under high pressure, and contributes to a better understanding of liquid–liquid two-phase flow behavior.  相似文献   

18.
19.
Presented in this paper is a computational analysis of the mechanisms involved in plastic deformation and fracture of a composite with coating under compressive and tensile loading. Using a steel specimen surface-hardened by diffusion borating, a role of the irregular geometry of the interface between the base material and hardened surface layer is investigated. In order to describe the mechanical behavior of the steel substrate and brittle coating, use is made of a plastic flow model including isotropic strain hardening and a fracture model, respectively. Using the Huber fracture criterion, the model takes into account the difference in the critical strength values for different types of local compressive and tensile states. It is shown that the irregular, serrated shape of the substrate–coating interface retards propagation of a longitudinal crack into this coating and prevents it from spalling under external compression of this composite. It is found out that even in the case of a simple uniaxial compression of the mesovolumes of this composite the boride “teeth” are subjected to tensile stresses, whose values are comparable with those of the external compressive load, and the direction of crack propagation and the general fracture behavior largely depend on the external loading conditions.  相似文献   

20.
Condensing of a sugar–water solution is a widely used production process, especially in food industry. In this study, boiling temperature and heat transfer of different concentration levels of sugar/water solution is experimentally studied. In the experiment, the pool boiling with constant temperature difference between surface and boiling temperature is investigated. Boiling point of sugar/water solution depends on sugar mass concentration and on vapor phase pressure. A function is suggested to calculation the boiling temperature. The experimental data and the calculated values of boiling temperature are compared. The results are verified with previous investigations. It is determined that the heat flux between surface and sugar/water solution while pool boiling displays a linear relation with water mass concentration in the solution. Heat transfer coefficient could be determined in dependency of surface temperature and sugar mass concentration. Furthermore a function is suggested to predict the heat flux for engineering purpose, which is already used in similar form for pure substances.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号